Search Documents

By Percival Roberts

IT may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or paddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By H. Biloni, B. Chalmers

Metallographic studies of the segregation of solute in and near the surfaces of chill-cast alloys have shown that, under sufficiently severe conditions, nucleation on the cold mold surface is followed by the formation of a disc of solid of the same composition as the liquid. This disc is surrounded by two concentric rings in which the concentration first decreases and then increases. The discs and rings are surrounded by a region in which arms of low solute concentration separate regions of high concentration. These arms start at the periphery of the outer ring and are initially radial; they make a gradual curved transition from the radial direction to a crystallographic direction. A normal dendritic substrcture is established beyond the position at which the arms have become crystallographically aligned. When the cooling is less severe, the disc becomes less irregular in shape and has a concentration minimum at the center. The term "Predendritic" is proposed for these transitions. A qualitative explanation is outlined for the phenomena observed at the surface and in the equiaxed region of the ingots. It is well-established1-' that the normal mode of solidification for alloys under most conditions is dendritic. A characteristic of dendritic solidification is the growth of rods or plates in specific crys-tallographic directions. The remaining liquid solidifies later, usually with a higher concentration of solute than the original liquid. Very little is known, however, about the transition from a crystal nucleus until the dendritic pattern is established. It is clear that there must be a transition because the nucleus is much smaller than the characteristic spacings found in the "steady-state" structure. And it also seems clear that the initial conditions must be important since the undercooling existing during the nucleation of the grains has a remarkable influence upon the grain size4 and the segregation pattern. The present paper reports a study of the micro-segregation in regions where crystals have nucleated, and the conclusions that can be drawn regarding the early stages of growth, in connection with the details of the solidification process. Aluminum of 99.993 purity, A1-Cu alloys containing 0.5 to 20 wt pct Cu, and Pb-Sn alloys with 5 wt pct Sn were cast and examined metallographically at the as-cast surface, close to the surface, and in the interior after casting. The alloys were cast from controlled temperatures against surfaces at different temperatures ranging from room temperature to approximately the liquidus temperature of the alloy. The surfaces were, in various experiments, graphite, stainless steel, copper, and aluminum. The methods used for metallographic examination were as follows. 1) The Nomarski phase contrast interferometer6 was used to obtain information on the topography of the as-cast surface. 2) The distribution of any solute present in A1 99.993 pct and copper in the A1-Cu alloys was studied by the anodic film technique originated by Lacombe and Mouflard7 and previously applied in the study of the solidification of aluminum by Biloni.8 The electropolished surface of the specimen is anodized under controlled conditions so that the thickness of the oxide film and therefore the interference colors under white light are sensitive to the local composition. This technique was applied to the as-cast surfaces and to metallographically prepared surfaces from the interior. 3) If in Al-Cu alloys, the surface is anodically oxidized for several minutes, instead of seconds as in the color-film technique, the copper segregation is outlined by a different level with respect to the matrix. This method is less sensitive but complementary to that for the color films. 4) The distribution of copper revealed and mapped by the metallographic techniques was confirmed by electron probe. 5) In samples with high concentration of copper, evidence for the copper distribution could be seen optically after electropolishing.

Jan 1, 1965

By C. L. Barron, M. L. Smith, K. A. Prisbrey

SAG mill throughput is often a bottleneck to increasing plant productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility, which is also related to the rock fragmentation that is achieved by blasting. The relationship between the size distribution and fragility of the feed and the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1994

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By Eren H

For a hydrocyclone of fIXed geometry, DC, Di, DO and ? are constants, the variable parameters affecting the performance are Qi, Fi, Du and H. (See Appendix 2 for definition of symbols).The relationship between d50c, Qi, Fi, Du and H gives models which can effectively be used for performance predictions. Such models have already been established by Lynch et al and by Plitt.These models have been tried in a limited manner under continuous operating conditions for on-line cowol. For on-line control effective and accurate instrumentation is required for which a new set up is proposed. Using this set up, a new model was established. A feature in this model is that deviations from the norm of operational parameters affecting d50c were considered. It is shown that these deviations generated by the disturbance of one or more of variations in the parameters, can be monitored by a computer and suitable signals generated to control servo mechanisms for restoring the required d50c value.The logic followed in developing the computer software is described and the application of the model is indicated.

Jan 1, 1990

By Alan Lawley

AS part of a programme of experimental work on single crystals of rhenium and ruthenium, it was found necessary to have the crystallographic angles for these elements. The angles given in Table I were determined to the nearest minute of arc, by Univac Computer. The angle $ between (HKIL) and (hkil) is given by the formula: The angles given for rhenium should be particularly useful in view of the increasing interest in this element. For completeness, angular values are also given for cadmium zinc and magnesium; these form a more complete set of values than those given by Salkovitz.' The assistance of Professor J. Hobstetter and Mr. J. Crozier in the programming of this data is acknowledged. The work is sponsored by the Office of Naval Research under contract No. NONR 551 (19).

Jan 1, 1961

By B. Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to he porous. In- deed, sponge iron, prepared by rcduction of the oxide in a reducing gas, is generally accepted as quite porous. with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig r shows commercial tungsten powder magni- fied at I0,000 X by the electron microscope,' both etched and unetched. In an earlier paper by one of the authors,* the existence of ports in tungsten powder was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these {pores} are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than IOO A. and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1949

By Bernard Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to be porous. In- [ ] deed, sponge iron, prepared by reduction of the oxide in a reducing gas, is generally accepted as quite porous, with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig I shows commercial tungsten powder magnified at 10,000X by the electron microscope,1 both etched and unetched. In an earlier paper by one of the authors,2 the existence of pores in tungsten powder [ ] was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these pores are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than 100 A, and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1948

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By L. S. Darken

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970

Coal strip mine operators in Western Canada often mine steeply-dipping multiple coal seams in mountainous terrain. The ability to fragment the rock waste layers above and below these seams with minimum disruption of the seams in large blasts normally involves decked charges in large rotary boreholes. Mining these seams may take two or more separate blasts to break the waste wedges above and below the coal, but these wedges can be blasted in a single shot for better mining efficiency.

Jan 1, 1985

By P. Barnes

In vol.33 of the Proceedings of the Institution of Civil Engineers, London (part 2, for 1870-71), may be found a statement of the cost of two blast furnaces, together with a somewhat detailed description. The attempt will he made in this note to restate these items of cost, so that the information may be rendered perhaps more accessible to our members than in its present place of record, and also in order that the items may be more intelligibly compared among themselves, or with similar items in other cases.

Jan 1, 1879

By L. Cifuentes

Electrodialysis (ED), i.e. a technique based on the effects of electrically charged membranes on ions in solution in an electric field, has been applied to Cu-Fe-As-Sb- H2SO4 electrolytes similar to those used in copper electrorefining and electrowinning operations. The effects of current density, time and species concentration have been studied in a batch ED cell. The technique has shown to be effective in concentrating and separating a range of ions and points to possible new methods of treating copper electrometallurgy effluents.

Jan 1, 1999

By D. Oyler

The National Institute for Occupational Safety and Health’s(NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tail-gate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

Jan 1, 2004

By Charles E. Locke

The little stamp-mill in the mining laboratory of the Massachusetts Institute of Technology and the work done by it have been well described by Prof. R. H. Richards and E. E. Bugbee in a paper read at the Albany meeting of the American Institute of Mining Engineers, February, 1903.' As run for student class-work the mill contains a feeder, stamps, plate, and vanner. Results in the past indicate that the work of these machines is just as efficient as that of a regular mill handling the same class of ore. It has been the custom to obtain ore principally from Nova Scotia, mainly because it is the nearest source of supply, and also because there is a considerable saving in freight-cost as compared with other districts. The gold in Nova Scotia ores is notoriously coarse, and for this reason it is almost impossible to obtain satisfactory results by sampling and fire-assay, unless an extremely large lot of ore is crushed and all of the contained gold pellets are saved. A very interesting and most extraordinary example of this fact has been presented by a recent run in the Technology stamp-mill. Since the capacity of the mill is about 60 kg. per hr., and since in about 5-hr. run the students in any one section have an opportunity to make the necessary study of machines, it usually happens that several runs are made from one lot of ore. When the shipment is received it is first dried and weighed, put through the Blake breaker, set at 1 or 1.5 in., and the crushed product is piled in a cone on the sampling-floor. When the crushing is completed the ore is usually stored away in barrels for future use; it is aimed to have each barrel of

Jan 1, 1914

By Ellis Clark

THE mining town of Pribram is situated in Central Bohemia, on the western slope of the Heiliger Berg, 30 miles southwest from Prague. Birkenberg, the village in which most of the shafts and ore-dressing establishments are situated, is built on a mountain of the same name. It is about a mile from Pribram, is 1700 feet above the sea, and is surrounded by graywacke rocks of Silurian origin, which are intersected by greenstone dikes, and in the southerly, southeasterly, and southwesterly direction are bounded by granite. The graywacke formations consist on one side of graywacke sandstone and quartzite, and on the other of graywacke slates. These last are separated from the first in the immediate vicinity of the mines by a graywacke seam converted into clay. For many years this so-cal led clay seam (lettenkkluft) was considered as a boundary of the ore deposits in both zones of graywacke. The graywacke formation is divided according to its hardness, structure, texture, and color, into fine, coarse, compact, slaty, whitish-gray, reddish-gray, and black graywacke. The, miner divides the formation into four divisions. The first or lowest division, which is in contact with the granite, consists of a fine-grained dirty gray slate; the -second is a very fine to a very coarse schist, white to reddish-gray in color, and rich in quartz, but containing little mica; the third consists of a slate with a contused cleavage, which has a dirty gray, dark gray, and very often black color and is often graphitic in its composition ; the fourth consists of a fine to coarse-grained graywacke schist, of a grayish-white or reddish-gray color, and rich in quartz. The cleavage in all four divisions strikes from northeast to southwest, and the dip is sometimes northwesterly, sometimes southerly, and often vertical. All four zones are cut through by a great number of diorite and greenstone dikes and chimneys. The thickness of these dikes, which are of

Jan 1, 1881

Many volcanoes in western Melanesia have tectonic settings and rock compositions that do not conform to conventional models of arc- trench systems. Part of the reason for this may be that in an environment of rapid tectonic change mantle source regions bear the imprint of former subduction even though subduction has now ceased. Results bearing on this concept and on other important aspects of Plelit nesian v ican ism and tectonics, were obtained in 1982-1986 from >e,:eral marine - geoscience studies in the re,,ii n

Jan 1, 1987

By J. S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1983

By Woods PW

Consulting Engineers have been used in the mining and metallurgical industries for many years. The traditional role of the consultant overseas has been one of assisting with conceptual design right through to con- struction and commissioning as well as on occasion acting solely in specialist fields. This role developed because mining companies wished to concentrate on building up the permanent organisation they require to operate their mines and treatment plants without the traumas of increasing staff for the design and construction period and reducing it on completion. In Australia where there have been few individual minerals projects of magnitude (until recently) companies have looked after their own detailed engineering and construct- ion management employing consultants mainly in specialised fields.

Jan 1, 1975