Search Documents

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By W. R. Dengler

In Canada, most of the rock being broken in underground metal mines is being done by using traditional drilling and blasting methods. Despite advances being made in hardrock boring and other, more exotic techniques, Dynatec believes that the traditional methods will prevail for many years. It is also believed that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunneling businesses. Dynatec has pursued productivity improvements through the use of long rounds in shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC, 1991). This technology was subsequently used to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunneling is a natural progression of the long round technology developed for the Craig Shaft. The Dynatec Long Round System has been patented in the United States and South Africa, with additional patent applications pending in Canada and Australia.

Jan 1, 1993

By J. A. Smith

The topic assigned me by the Chairman of the Institute, "Safety Practices in Franklin and Williamson Counties, Illinois," I fear will necessarily resolve itself into a paper on shale dust, its application and the results obtained. I returned .only last week from a three weeks trip through these counties at which time, through the courtesy extended me by the operators, I had ample opportunity to visit and inspect many of the largest mines in the field, some of which are among the largest in the United States. With the exception of shale dust and ventilation, I see but vary few instances where the Illinois mines are further advanced in safety precautions than the western mines, and in some respects I believe the operators of the West are further advanced in safety methods than their eastern brothers. Great care is exercised in handling of all ventilation currents. This is an aboslute necessity, as this field is quite gaseous, and the peculiar geological structure of the overlying and underlying strata makes airtight seals very

Jan 1, 1924

The Jacobs Sliding Floor (Floor) is experiencing a surprisingly long competitive life. The first Floor was used on the Camino Tunnel in California in 1960. At that time the Robbins Company had built only seven TBMs, and the future for such machines was considered doubtful by many, as compared to drill and blast methods. This was then, and still is, commonly called the "conventional" method. Robbins' TBM No. 8 was for the Hydro Electricity Commission of Tasmania (HEC) for their Poatina Hydro Project in 1961. In this writer's view, the Poatina experience was the start of successful hard rock boring machines. But, by coincidence, the HEC is using the newest Floor for their King River Hydro project, where driving with the Floor started in July 1986 on the King Tunnel. This paper examines the history and developments in both Floor design and other "conventional" tunnelling equipment, and the site specific conditions that have allowed this old concept to still be competitive in certain select situations. Parametric costing data and some actual progress records are included.

Jan 1, 1987

By John Cobb

THE attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinations of ,the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia, at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal, and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in another way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 3, 1925

By John W. Cobb

The attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinitions of the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia,. at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal; and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in &other way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 1, 1925

IN this paper the author's intention is to convey a brief resume of the lead flotation treatment and lead flotation machines, which have replaced the May jigs and Wilfley tables at the plant of the North Broken Hill Ltd., and converted this mill into an all-flotation plant.Attention is directed to the fact that this drastic change from semi-gravity to all-flotation treatment, has been successfully accomplished without resorting to finer grinding than that previously in vogue for Wilfley table concentration, viz.: 10% to 16% plus 40-mesh I.M.M. screen.From the figures now available it is manifest that the scheme of all-flotation concentration-new as regards its successful application to Broken Hill ores is resulting in considerably higher-grade lead concentrates, and is substantially decreasing charges for labour, stores, and maintenance.The new treatment is far-reaching in its simplification of plant, as evidenced by the idle jigs and tables, and the results being obtained by North Broken Hill Ltd. may possibly influence metallurgical practice generally in Broken Hill.The outstanding features of the treatment are:(1) The coarseness, and high grade of lead concentrates obtainable.(2) The low time factor required for flotation.(3) The plant capacity, and the simplicity of its operation.(4) The low horse-power consumption.(5) The small cost for reagents used (not exceeding 3d. per ton of ore).

Jan 1, 1930

By Stephen Birch

The Chitina mining district of Alaska is located at the headwaters of the Chitina and Copper Rivers. At present, the only producing mining properties are the mines of the Kennecott Copper Corpn. and the Mother Lode Coalition Co., which are situated 196 miles from Cordova, the port of entry. The first claims, later acquired by the Kennecott Mines Co. and afterwards transferred to the Kennecott Copper Corpn., were discovered in 1900. The Copper River & Northwestern Ry., which connects the mines with tide water at Cordova, was completed in the spring of 1911. Contemporary with the construction of the railroad, aerial tram equipment was brought to the mines by pack train and a tramway, 3 miles long, connecting Bonanza mine with the proposed railroad terminal, was finished, enabling shipments of high-grade ore to be made immediately the railroad was completed. A mill to treat the lower grade ore was begun the same year. The Kennecott company's holdings consist of 111 mineral claims. The Mother Lode Coalition Mines Co., which is controlled by the Kennecott Copper Corpn., owns 73 claims adjoining the Kennecott holdings. All data on operations and geology refer equally well to the Mother Lode property. Geology The general geology of the district has been covered by the U. S. Geological Survey1 and the geological features of the mines have been carefully studied by A. M. Bateman, in his capacity as consulting geologist to the company.2

Jan 1, 1925

By S. R. Mitchell, M. Weissman, J. H. Brown

It has been demonstrated that for fine grinding operations, the energy input (E) and the product size modulus (k) are related by an equation of the form E = Ak1-n (1) where "A " and "n" are constants.(1) Also, it was suggested that "A" is determined by the comminuting device and that "n" depends primarily on the rock. It was the purpose of this investigation to study these constants by determining the form of an energy-size reduction relationship over an extreme range of energy inputs, and at the same time, to evaluate the minimum particle size produced during grinding. The comminution system consisted of a stainless steel laboratory ball mill in which quartz was ground at 60% solids for times ranging from 1 minute to 700 hours. The mill which measured 10" diameter by 12" long was loaded with about 60 pounds of balls ranging in diameter from 3/8" to 1-1/8" and was driven at 55 r.p.m. Quartz was selected for the tests because it is a brittle material for which size distribution data were expected to show a constant distribution coefficient regardless of product size.(1) This permitted specification of product size by a size modulus alone. The quantities measured were the time of grind (measure of energy input) and the specific surfaces of the products. Since no accurate method is available yet for determining particle size directly in the very fine size ranges specific surface data were used for this purpose. The relationship between these two quantities may be expressed as where Cis a constant which includes a shape factor, p is the specific gravity of the solid,_S is the specific surface and D is an equivalent particle diameter. For a material in which the distribution coefficient does not change with size the term (l/S) may be substituted for k in equation L if the proportionality constant "A" is changed correspondingly. This substitution was made in this work but in addition, screen analyses were made on several products to verify the equivalence of the two methods of size specification. EXPERIMENTAL DETAIL QUARTZ Quartz from two sources was tested. One series of tests was made on a clear, high purity crystalline quartz from Brazil and Arkansas, and another series was run on massive quartz fromNewHampshire. Grinding charges of the high purity material consisted of 2000 gram samples of -3-8 mesh particles, while the charges of the New Hampshire quartz were 500 gram samples of a -35+48 mesh screen fraction. The difference in the sizes of these two series of charges was not significant in view of the extreme size reduction accomplished, and the New Hampshire samples were smaller to permit ginding to finer sizes in shorter times than required for 2000 gram lots. SAMPLING AND ANALYSIS Separate charges were ground for all tests in which the grinding times were less than one hour and for all tests on New Hampshire quartz since these products were difficult to sample accurately without affecting the entire charge. During the long time grinding tests the mill was

Jan 1, 1961

By Gregory Comstock

THERE is a growing interest in the possibilities presented by the manipulation of metal powders, which justifies an attempt to summarize their character and potential value. A summary of this kind presents an opportunity for making a classification of metal powder products into several general types. Our present knowledge of the finer and more abstract aspects of many of the principles involved in metal powder technique is extremely limited. Any conclusions as to the ultimate value of the process will, therefore, for the present at least, be of doubtful value unless they are substantiated by its products. The number of such products is increas-ing. A study of their diverse and unusual characteristics; an examination of the methods by which they ale made, and a consideration of the reactions that take place during their fabrication, in so far as we can define them, should afford as good an evaluation of this interesting development as it is possible to make at this time. A critical study of this kind results in a formidable list of special attributes, which apparently are characteristic of applied powder metal-lurgy. A comparison of these special effects with the end products and well defined limitations of the melting and casting process indicate that often they may very well be considered as being special advantages. They are subject, of course, to certain not as yet so well defined limita-tions of their own. Based on current products only, a necessarily con-densed summary of the more striking special attributes of the metal powder process follows.

Jan 1, 1938

By G. I. Voiloshnikov, A. F. Panchenko, N. S. Voiloshnikova

Low world gold prices stimulate development and introduction of economically efficient ( cost saving) technology for operating gold mills. This report covers the results of testing and introduction of CIL technology to recover gold from flotation concentrate of Samarta gold concentration plant located in Buryatia (Russia). This plant is treated the ore of Zun Kholba gold deposit using gravity and flotation of gravity tails as preconcentration processes. Till recently high grade gold gravity concentrate was smelted to gold bullion and shipped to gold refinery, gravity middlings were leached by cyanidation in cone type equipment developed by Irgiredmet and flotation concentrate shipped to copper smelter. The disadvantages of flotation concentrate shipping to copper smelter are following: high concentrate transport cost; problem with gold shipped balance; high cost of flotation concentrate treatment; comparatively low gold recovery. In this connection IRGIREDMET developed the hydrometalurgical technology for gold recovery from flotation concentrate. The flowsheet was developed on the base of laboratory, pilot plant and industrial scale tests conducted by IRGIREDMET in 1987-1997 and lrgiredmet experience on CIP process testing and industrial scale introduction in Yakutia [1-6]. The flowsheet is presented in Fig.1 and consists of following base operations: concentrate regrinding;

Jan 1, 1999

While South Africa is well endowed with mineral resources, it is generally accepted that its future will be determined more by the development of its human resources than its mineral wealth. The country has throughout its modern history suffered from an over-supply of unskilled labour and a shortage of skilled and professional manpower. There has furthermore always been an over-reliance on Whites as an internal source of professional manpower, supplemented by immigration wherever possible. Better utilisation of other population groups in professional positions has been hampered by the general lack of education and training among such groups. Although many problems still remain, there are emerging trends which are likely to positively affect the training of professional manpower in the future. The direct and indirect influences that are likely to affect professional training at the macro level include 1. government policy and objectives in respect of manpower education and training, 2. the emergence of technikons as fully- fledged tertiary education institutions, 3. demographic trends in South Africa as they pertain to education, 4. political and statutory developments in the country, 5. industry involvement in tertiary education, and 6. professional registration.

Jan 1, 1986

By K. Hanumantha Rao, K. S. E. Forssberg

The limestone deposit of Gâsgruvan, Sweden contains around 89.2 per cent of calcite. Conventional and column flotation studies have been carried out using sodium oleate and modified fatty acid collectors in the presence of sodium silicate modifier. The effects of collector and silicate concentrations, and particle size on the flotation response of calcite have been investigated. The results have been discussed in comparision to the performance of conventional and column flotation cells. The feed size is found to be a significant factor to achieve a high grade calcite concentrate either by conventional or by column flotation. The loss of selectivity at fine particle sizes is examined using a modified DLVO theory.

Jan 1, 1995

By A. B. Cox, L. W. Wark

In the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practised at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts of many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies—the Broken Hill South, the North Broken Hill, and the Zinc Corporation—together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism. After an extensive search of the literature, it was decided to determine in a preliminary investigation whether the effect of chemical collectors could be evaluated quantitatively by the "contact-angle" method. This preliminary investigation showed that with the bubble machine of

Jan 1, 1935

By W. K. Hardy, H. H. Stadelmaier, L. J. Huetter

The ternary system Co-Sn-C was studied in the cobalt-rich region. The liquidus projection ulas established and two fonr -phase reactions were found. An isothermal section at 950°C was worked out. In the region studied the following phases were observed: cobalt-rich solid solution, graphite, binary compound y -cobalt-tin, and a ternary compound. As a result of the limited solubility of carbon in liquid cobalt-tin alloys, the investigation was limited to the cobalt-rich region. Tin contents up to 32 at. pct were studied. Cobalt of 99.99 pct purity, tin of 99.97 pct purity and synthetic graphite of 99.93 pct minimum purity prepare the alloys. Carbon determinations of all alloys were obtained by gas volumetric analysis. Samples were investigated microscopically and by X-ray diffraction using CoK, and FeK, radiation. Cooling curves were obtained with a number of alloys to determine the temperature of the four-phase reactions. The thermocouple was calibrated with the melting points of high-purity silver and copper. In the region studied the following phases were observed: Cobalt-rich solid solution (face-centered cubic) Graphite. Binary compound y (solidifies congruently at composition Cop~n)'. Ternary compound k which is face-centered cubic with superlattice and nonferromagnetic.' In Fig. 1 the fields representing the projections of the liquidus surfaces were determined by microscopic investigation and are labled by their primary phase. In the field labled C graphite is the primary phase. During solidification in this field much of the primary graphite was expelled through the surface of the melt. It could not always be established microscopically whether the remaining graphite was primary or purely eutectic. Therefore it was not possible to determine accurately the boundary curve which drops from the binary eutectic el at 1309 "~~ to the point of the four-phase reaction at F. The ter-nary carbide is the primary phase in the field labled k. To the right of this field the primary graphite is consistently nodular whereas flake graphite is observed at tin contents somewhat below F. The ternary carbide does not appear to solidify congruently. The graphite is attacked in a peritectic reaction along the boundary between k and C. Thus no graphite is observed in alloys in the k field. In alloys right of the boundary between k and C the graphite nodules are located in the center of the k crystallites, further documenting the peritectic nature of the reaction with the graphite. A four-phase reaction was found at F and 1120 &3"C. The most likely reaction is L+ CY-Co + C — k. Below the temperature of the binary eutectic ez at 1112" a second four-phase reaction was observed at E and 1100 lt3"C. It is the ternary eutectic L — CY-Co + k + y. Figs. 2(a ) to (e) show microstructures of the ternary alloys in the as-cast condition. Fig. 2(a) shows the eutectic a-Co + C (with some primary graphite) with the carbide k in the grain boundaries. Fig. 2(b) shows primary cobalt (dark areas) and the eutectic a-Co + k which is formed along F-E.

Jan 1, 1961

By E. L. Bruce

The district of Patricia, in the province of Ontario, lies northwest of the Albany River and extends northward to Hudson Bay. Formerly this was the unorganized district of Keewatin, the southern part of which was divided in 1912 between the provinces of Manitoba and Ontario. The interprovincial boundary now runs north from Lake of the Woods for 275 miles and thence northeast 375 miles to Hudson Bay. This district is comparable in size to all the older part of Ontario south of the Canadian Pacific Railway east of Lake Huron—thus it is roughly one-third of the whole of the present provincial area. The central part of this great triangle is one of the least accessible parts of Canada. From it streams flow southward to the English River, southeastward to the Albany, northward to Hudson Bay and the Hayes River, and westward to Lake Winnipeg. None of the streams is large and canoe travel is not easy. The only industry it has ever had is the trade in furs. Until the development of the airplane on a commercial basis, the only means of travel was by canoe or dog-train. There is not a mile of railway in the whole district. The two areas to be dealt with lie in the southwestern part of Patricia. Red Lake is 50 miles east of the Manitoba boundary and 75 miles north of the transcontinental railway from Cochrane to Winnipeg. Woman Lake is 50 miles farther east and slightly farther north. The late Dr. D. B. Dowling, of the Geological Survey of Canada, visited Red Lake and spent some time there during his exploration survey from Lac Seul to Berens River in 1893. He also visited the Woman Lake basin during the same journey, but his examination of it was much less detailed, the great area covered by him during the one field season making it impossible to make more than a hurried reconnaissance. Some prospecting in the Red Lake district followed Dowling's exploration, but the distance from railway was too great for any systematic work to be done. In 1922, following the usual plan, the Ontario Department of Mines made a geological reconnaissance of the English River, following :in instrumental survey of that river and its lakes by the Department of Lands. A side trip was taken to examine the rocks of Red Lake described

Jan 1, 1928

By M. Nicolle

The Tati Activox® Project will be the first full-scale implementation of the patented Activox® process (The Tati Activox® project was deferred in 2008. Please refer to the Norilsk Nickel press issue on the topic for more info). The process was developed by Norilsk Process Technology and has been tested on Tati mine sulphide concentrates in laboratory, pilot and demonstration plant scales and demonstrated its viability. There are inherent risks to the final scale-up of the process from the demo plant and one of them will be investigated in this paper. Compartment 1 is designed to leach approximately 77% of the total nickel leached. For this reason agitation requirements in the first compartment of the autoclave are reviewed. An attempt is made to minimize the process and mechanical risks associated in achieving oxygen mass transfer into the slurry solution. The agitator powers for oxygen mass transfer are calculated using empirical correlations and compared to demonstration plant testwork. The resulting gassed power per unit volume (P/V) is higher than most commercial autoclaves and raises uncertainty on the viability of using such high unit power inputs. Additionally, there is concern about the ability of the autoclave shell to withstand and support the higher loading of large agitators. An alternative solution to designing for the increased P/V is assessed in which the number of compartments within the autoclave is reduced from 5 to 4 by removing the compartment wall separating compartments 1 and 2. This results in an enlarged first compartment containing 3 agitators instead of 2. Therefore the compartment 1 oxygen demand is supplied through 3 agitators, which lowers the P/V per agitator. The reduction in the number of autoclave compartments raises the potential for short-circuiting the mean flow pattern by slurry particles. Short-circuiting and low velocity zones could result in a lower recovery of metal and localized hot spots, respectively. A computational fluid dynamic (CFD) analysis was conducted to quantify these concerns and also to evaluate further design considerations. The results indicate that the proposed design change to 4 compartments affects short-circuiting. The impact of increased short-circuiting on the overall autoclave recoveries is not quantified, however; it is expected to be negligible based on testwork done in the Tati Demonstration Plant and similar modifications made to another operating autoclave. The CFD analysis also suggests that there will be no low velocity zones within the compartment.

Jan 1, 2009

By S. P. Lin

The numerical models of nonlinear piles for deep foundations are studied in this paper. The purpose of these is to clarify the mechanical behaviour of deep foundation nonlinear piles subjected to axial and lateral loadings. Based on the site data of p-y curve as well as t-z curve of foundation soils, it is possible to evaluate pile performance under above mentioned loads by means of combined FEM/FDM models. Numerical examples are presented in tall building and offshore jacket for illustrating the technique, it show high efficiency of these models. Some information to be interested by design engineers are given, especially for those who pay very concerns on the interaction behaviours of structure and its pile foundation.

Jan 1, 2010