Search Documents

By Artieda JJ, Catalina JC

- The aim of this paper is to analyse the possibilities of applying signal processing and artificial vision techniques to the ore sorting problem. In order to overcome the limitations imposed by the classical approach to the problem, which essentialy cons

Jan 1, 1985

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

Two separate mine rehabilitation programmes carried out by Australian Consolidated Industries Limited (A.C.I.) in South Australia at Normanville and Port Lawler are discussed. Emphasis is given to the methods used, the results achieved and to possible future improvements.

Jan 1, 1976

By Morrell S

As more and more autogenous and semi-autogenous mills are run in closed circuit with cyclones the limitations that can be imposed by poor grate and pulp lifter design are becoming increasingly apparent. Relevant literature on the subject is al

Jan 1, 1997

By Richard Miller

The investigations of large-grained specimens carried out by Polanyi and Schmid,1 Sykes,2 Goucher,3 Yamaguchi,4 Gough, Cox, and Sopwith,5 Carpenter and Elam,6 Aston,7 and others have shown qualitatively that grain boundaries restrain the deformation of adjacent crystals. But whether or not the influence of the grain boundary is confined to the glide planes intersected by the boundary has not been demonstrated in any of these investigations, nor has there been carried out any quanti-tative analysis, of the influence of a boundary on the deformation of a crystal. Indeed, the specimens employed in the previous work con-

Jan 1, 1934

By K. I. Afewu, L. C. Woollacott

Little is reported in the literature that is directly useful for the interpolation film coefficients for the in-pulp adsorption circuits used in gold metallurgy. This can create a problem if the design or operation of these circuits is to be optimized by the use of simulation techniques. To address this problem, a study was undertaken on the influence of mixing intensity, scale, and geometry on the film coefficient in adsorption systems typical of the carbon-in pulp plants used for gold extraction. This, the first paper deals with the influence of these factors on the film coefficient and shows that the specific power to just disperse the carbon in the slurry is an important variable. This variable is also strongly dependent on mixing intensity, scale, and geometry-a dependence that is dealt with in the second paper in the series. From the informatlon obtained, practical scale-up procedures were developed. These procedures are considered to be applicable to resin-in-pulp as well as to carbon-In-pulp plants.

Jan 1, 1995

By C. A. Landolt

Inco pioneered the use of tonnage oxygen in non ferrous metallurgy when it commissioned the first industrial oxygen f1ash smelting process for the treatment of copper concentrates in the ear 1y fifties. This techno logica1 innovation was followed by other applications of technical oxygen. Inco is currently implementjng a Sulfur Dioxide Abatement Program designed to reduce SO2 emissions from the smelter by 60% in 1994. The new flowsheet includes new equipment for the oxygen flash smelting of Cu-Ni concentrates and for flash conversion of chalcocite. Oxygen smelting and converting technology will lead to a substantial decrease in use of fossil fuels and to generation of high strength S02 off gases suitable for efficient fixation in a new acid plant.

Jan 1, 1992

By Stanley Reichert

The manganese deposits of the Embree Iron Co., Embreeville, Tenn., are thought to be fairly typical and representative of the East Tennessee type of deposit, and so to warrent rather detailed description. The methods used by the Embree Iron Co. for prospecting and mining, and to a lesser extent for milling; should therefore be applicable to other East Tennessee manganese deposits, as yet' undeveloped. Early History and Discovery of Manganese Brown iron ore (limonite) was mined by the Embree Iron Co. at various times from 1890 to 1910. The early method was simply pick-and-shovel mining in open pits. Later hydraulic giants were used and sluice lines carried the ore down the mountain slopes to log washers.. During this phase of mining, manganese ore was discovered under the iron ore in some of the pits. In other areas oxidized zinc ore was found under the iron. It thus happened that the valuable zinc deposits were discovered in 1914. During the World War period, from 1914 to 1918, there was sporadic prospecting for manganese ore among the abandoned iron workings, but the main activity then centered around the recently discovered lead and zinc deposits. It was not until 1934 that manganese mining began in earnest, under the supervision of R. D. Pritchett, Mine Superintendent. Geology of the Manganese Deposits United States Geological Survey Folios 151 (Roan Mountain) and 118 (Greeneville show that Bumpass Cove is a synclinal structure thrust faulted along the southeast flank, but with normal sequence of strata along the northwest flank. Fig, l. shows the areal geology of Bumpass Cove as taken from the folios superposed on the U.S.G.S. -T.V.A. 1/24,000 topographic maps of the Erwin and Telford 7 ½ minute sheets. The manganese mines occur near the contact of the unfaulted Shady dolomite and the Erwin quartzite. This contact zone is deeply weathered, with overburden averaging 40 to 60 ft. thick. The material overlying' the bedrock along this normal contact is a very tough, plastic clay, termed "buckfat" or "ocher" by the miners. It is not a true ocher, however, in the sense of having commercial value. The manganese deposits occur along this "ocher" band. Fig. 1 also shows how the manganese deposits occur along the broad topographic terrace between the 2100 and 2200-ft. contour lines. This terrace lies at the foot the Erwin quartz ridge. Apparently it is the topographic is expression of the deeply weathered zone along the Shady-Erwin contact.

Jan 1, 1941

By 000-000-604

HISTORIACAL INTRODUCTION Mineral processing has three principle branches, to quote Taggart, "Ore Dressing, which comprises the methods of separation of solids in inorganic crude by means which do not affect substantial chemical change; Extractive Metallurgy, which utilizes chemical reactions for separations of constituents from solids in inorganic crude; and, Fuel Technology, which employs both physical and chemical methods for separating and rearrangement of liquid gaseous and solid components in crude oil and natural gas, tar sands, shale oil, or coal." The scope of this handbook covers the first two classifications, that is, "ore dressing" and "extractive metallurgy," which have been combined in one term: "mineral processing." For a brief history of the development of mineral processing, one could well refer to the Introduction, Sec. I of the Handbook of Mineral Dressing by Taggart, Froth Flotation, Principles of Mineral Dressing by Gaudin, and the original Richard's Ore Dressing, volume No. 1, first published in 1903-1905. In these references and the references given in them a coverage of the history of "ore dressing" can be found and studied at the reader's leisure. For the history of extractive metallurgy as well as ore dressing, the bibliography in General References, taken from a History of Ex¬tractive Metallurgy by F. Habashi, will give a good background for those who are interested in more detail on the history of metallurgy in general. Mineral processing covers a very wide field as is illustrated by the topics discussed in Part II of this handbook and dates back to the early history of man which started with the production and use of native minerals such as gold, silver, copper, mercury, and meteoric iron which were washed or picked from deposits on the surface of the earth and worked because of their malleability. Later, melting was discovered and then it was possible to cast objects of these metals, excluding mercury. The discovery of a method for reducing the metal¬lic oxide probably was developed from melting fragments of oxides or roasted sulfides with charcoal, so that the native metal could be produced in simple blast furnaces such as are used today in rural parts of Spain, China, and elsewhere. Eventually, it was learned that iron could be readily worked when hot, which resulted in its replacing bronze for tools, weapons, and cutlery. Carbon dating and correlation with the Brittle Cone pine has

Jan 1, 1985

The Century zinc deposit is located in Queensland approximately 250 kilometres north north-west of the provincial city of Mount Isa, on Lawn Hill Station and within 150 kilometres of the Gulf of Carpentaria.ThefirstMining Lease in this area was pegged in 1887. The Silver King vein is the largestvein deposit in the area and has produced lead and zinc, in addition to 74,000 ounces of silver during its history.A total of forty three veins containing silver, lead and zinc are now known, all of which were discovered by prospectors within 10 years of the first vein being recognized.

Jan 1, 1993

By Masszi D

INTRODUCTION The association of methane with coal has been known almost since coal was first mined and in general it has been considered the curse of underground coal mining. Historically, most of the effort to handle this methane has been directed at diluting it to a safe level and preventing an explosive mixture of methane and oxygen from forming in any part of the mine. This is generally achieved by in-mine activites. This approach has two principal drawbacks, the severity of which are dependent on local conditions. The first is that the activity associated with the handling of the methane is undertaken in the mine and there- fore competes with the mining activity for the limited space available. The second drawback is that the whole methane handling activity is generally a cost to the coal because methane is so diluted that it cannot be used. With the value of energy increasing thi; second drawback is gaining importance so th.u several mines in Europe and North America ;it,, now installing systems to recover the methane in a useful form. Two approaches are

Jan 1, 1982

By C. A. Landolt

Inco pioneered the use of tonnage oxygen in non ferrous metallurgy when it commissioned the first .industrial oxygen flash smelting process for the treatment of copper concentrates in the early fifties. This technological innovation was followed by other applications of technical oxygen. Inco is currently implementing a Sulfur Dioxide Abatement Program designed to reduce S02 emissions from the smelter by 60% in 1994. The new flowsheet includes new equipment for the oxygen flash smelting of Cu-Ni concentrates and for flash conversion of chalcocite. Oxygen smelting and converting technology will lead to a substantial decrease in use of fossil fuels and to generation of high strength S02 off gases suitable for efficient fixation in a new acid plant.

Jan 1, 1992

By J. J. Sense

10.2-1. Equipment Scheduling. In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice for many obvious reasons, principally mechanical conditions, operating conditions, and human nature-this ideal situation is not possible. The cost-conscious organization strives to keep as many pieces of equipment of the fleet working efficiently as much of the work day as possible. Operating efficiency requires the minimum equipment to move the predetermined tonnages in the prescribed period of time. In the case of a shovel-truck operation this would mean the scheduling of the minimum shovel and truck shifts to excavate and transport the necessary tonnage to the processing plant or waste dump. To accomplish this goal, the operator must work from the predetermined production established by the requirements of the plant, stripping ratio, mine plan, etc. This production schedule may be in terms of tons or yards per year, per month, or per hour, but must eventually be translated into tons or yards per ma- chine per unit of time. In this regard, the reader is referred to Sections 8.0, Excavation and Loading, and 9.0, Haulage and Transportation. The trend to larger and faster, and as a result more costly, equipment requires that the operator consider every possibility to keep the equipment operating around the clock, seven days per week. In some areas seven day operation may not be feasible economically, because of premium pay for Sunday work. Mine labor agreements are generally written without premium pay penalties for weekend work, and such scheduling is possible and most often desirable.

Jan 1, 1968

By H. J. Struth

A glance into the immediate future of the refining industry, and a retrospective view of 1929, cannot fail to emphasize the need for effective measures of control of refinery still runs. With oil producers alert to the need for control of the crude supply, it has become more than ever necessary for refiners to complete the movement toward stabilization by concerted determination to maintain still run schedules within the limitations prescribed by the demand for gasoline. The outlook for continued growth in the demand for gasoline appears to be well sustained by a preliminary survey of requirements for 1930. In fact, it is apparent that the industry will be assured of a market for gasoline that will aggregate in volume at least 472,000,000 bbl. this year. This indicates a gain in total demand over 1929 of about 9 per cent. or about 4.6 per cent, less than the gain recorded during 1929 over 1928, which amounted to 13.6 per cent. Despite the indicated increase in gasoline demand this year, it is apparent that little, if any, more crude will be required than last year. This is shown in Table 1, presenting estimates of gasoline demand and probable crude requirements for 1930. Table 1.—Preliminary Survey of 1930 Gasoline and Crude Run Requirements Millions of Barrels Doniestic gasoline demand................................... 397 Foreign gasoline demand..................................... 75 Total indicated demand...................................... 472 Natural gasoline content..................................... 53 Net gasoline from crude...................................... 419 Imported gasoline........................................... 13 Net gasoline required from refineries.......................... 406 Indicated excess stock Dec. 31, 1929........................... 10 Maximum protluction required................................ 396" At 40 per cent. gasolitlc recovery, this represents a maximum crude converson of 990,000,000 bbl., or a daily average for the ycar 2,712,000 barrels. Year after year, the refining branch of the petroleum industry has been found guilty of running crude to stills greatly in excess of normal requirements, causing frequent periods of market depression. A review

Jan 1, 1930

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By T. P. Meloy

Recently, Gilvarry1 has criticized the Gaudin-Meloy2 derivation of the size distribution equation for impact grinding. The criticism states that as the derivation stands it is good for only a long, thin wire being fractured. This paper contains a second derivation in reply to the criticism. Consider a homogeneous solid particle. This particle is broken into fragments by impact. It is assumed that the material resembles galena and that the particles were broken into chunky parallelepipedes which may be treated as cubes. The fragments are now reassembled — as seen in Fig. 1 — and a line is passed through the fractured solid perpendicular to one of its faces. For simplicity, the length of the line segment in the cube is considered to be 1. Fig. 2 represents the line segment in the cube showing the locations of the crack surfaces cutting the line and one point, P, chosen at random on it. The question arises as to what is the probability of the point, P,

Jan 1, 1963

By Leon Merker

FLAME fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904,1 was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile,2 mullite,3 and ferrites4 One of several significant advantages of the flame fusion technique over more conventional methods of growing crystals from a melt is that the crystals are grown without the use of melt containers. This fact alone excludes other methods of growing crystals from a melt whenever there are compounds with a melting point near 2000°C or above. Growth of the crystal, similar to that of a stalagmite, takes place inside a circular refractory furnace that does not contact the crystal, Fig. 1. This eliminates a serious source of impurities as well as the likelihood of multi-crystalline solidification along the container walls. The flame fusion technique is particularly advantageous for research because it produces large crystals quickly and at lower cost. A corundum crystal 25 mm long and 12 mm in diam can be grown in 2 to 3 hr. Operating conditions permit observation of the growing crystal during any stage of the process. The various flame patterns and a wide range of oxidation-reduction conditions can be investigated in a relatively short time. It should be pointed out that formation of the foot of the boule is the most critical step in growing an unfractured boule. When the tip of the sintered cone is fused to initiate crystal growth, the original area of fusion should be kept as small as possible so that one crystallite can assume dominance over all the others and propagate as a single crystal. If the boule start happens to consist of several crystals, usually the entire boule also contains several crystals. In many cases these tightly cohering crystals exhibit different crystallographic orientations. Although the basic technique of the original Verneuil process has been retained, refinements in method and burner design have been developed in recent years. For example, boule growth may be initiated on a seed crystal rather than by fusion of a sintered cone. The danger of multicrystalline or twinned boule starts is thus eliminated, and this procedure may also be used to grow boules of predetermined crystallographic orientation. Prior Art: Of the many attempts to produce artificial gem crystals, most early efforts% ere directed toward synthesis of .rubies and sapphires and diamonds. None of these efforts resulted in a process that was commercially practical. Without exception only tiny crystals of corundum were obtained, and those at excessive cost. Verneuil announced his process in 1904; Ravier6 in 1934 presented a detailed description of a commercial boule production plant. Descriptions of the German synthetic stone industry, the process details, and the equipment used have been published by Barnes7 and by Merker.'

Jan 1, 1956

By G. F. Willis

Gold mineralization in the Mesquite district is hosted by a series of Jurassic amphibolite grade metamorphic rocks which have been intruded by a Cretaceous leucogranite pegmatite. A series of northwest trending, high angle, normal faults have apparently acted as a structural locus for mineralized epithermal fluids and thus economic concentrations of gold in the Big Chief orebody. Late Tertiary fault reactivation has bounded the fault and fracture controlled mineralization. Popular theories of ore genesis call on, (1) Tertiary detachment faulting, (2) the Cretaceous intrusive, or (3) the opening of a dilational jog between regional dextral strike-slip faults as a source powering the gold bearing hydrothermal fluids.

Jan 1, 1988

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) The governing body of the Imperial College of Technology, London, S. W. (Royal School of Mines), will shortly proceed to the appointment of a Professor of Metallurgy. This important Chair has been filled in the past by such eminent metallurgists as John Percy, Sir William C. Roberts-Austen, and others. Inquiry has been received at the office of the Institute for an engineer to examine a mica, deposit in one of the New England States. The position of converter blower at. a side-blow Bessemer steel casting plant is vacant.

Jan 4, 1913