Search Documents

By J. B. Wagner, B. Swaroop

The atomic ratios of oxygen to iron in zlarious corn-posilions of wustite in the vicinity oj the reported p to n transformation were determined in the temperalure range between 950" and 1250°C. For these conditions, equilibrium vacancy concenrations have also been determined at vatious mixtures of C0,-CO. The data show a continuos introduction of iron vacancies as oxygen is introduced into wuistite. No phase change is observed with in the wuustite field. However, the value of n in the isothermal oxygen pressure dependence, the weight change shifts to 1ower values as the concentration of oxygen increases. WUSTITE is a metal deficit semiconductor with the majority lattice disorder being cation vacancies. Using the notation similar to that of Kroger and ink,' the dissolution of oxygen into wiistite using C02-CO mixtures is represented by, WHere v+! denotes a cation vacancy with k effective negative charges and kh • denotes k electron holes, h -. Applying the law of mass action and assuming a dilute solution of defects in the wiistite yields Where the square brackets denote concentrations. Furthermore, when k = 2 the cation vacancies are completely ionized, and both the concentration of cation vacancies and the concentration of electron holes are proportional to the third root of the ratio, PC /PCo. This analysis is valid for one particular mael based on an ideal solution at elevated temperatures (in this case t > 1000°C). At lower temperatures, it has been shown2 that the pressure dependence of the electronic conductivity changes in a manner which suggests that vacancies interact with or "trap" electron holes. At the very high concentrations of defects, 10'' to 10" per cu cm, these simple models no longer hold. Recently Tannhauser,3 Geiger et a1.' Bransky and Tannhauser; and Hillegas' have found an apparent p to n transformation in wiistite in the temperature range of 950" to 1300°C. This junction was found by thermoelectric and electronic conductivity measurements. Geiger eta1.' found that the electronic conductivity became almost independent of the oxygen pressure at high temperatures and oxygen concentrations within the experimental error. In addition, Vallet, Raccah, and coworkers6'7 have reported the existence of several "varieties" of wiistite which were reported to exist within what was heretofor presumed to be a

Jan 1, 1968

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah, The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 in. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements, They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics' have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I. 03 -1.06 Acid number.................. 6-8 Softening point, mercury method 160°-165°C Iodine valus (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residua] coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction CO., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1949

By W. F. Mattes

The manufacture of steel rails in the United States upon a large scale may be roughly dated from the years 1875-76, and the same years witnessed an active movement among the railroads toward the adoption of heavier and improved patterns. In this movement each road was a law unto itself, and the "personal equations " of some scores of engineers were so freely injected into the calculations that patterns were multiplied in the most absurd and mischievous manner, until at length the burden upon the mills became wellnigh unendurable, and called forth a vigorous protest in Mr. Holley's paper,* read before the Institute in February, 1881. There were then regularly manufactured in the various mills of the United States, no less than 119 different patterns of steel rails, subject to current order, of which 64 per cent. were embraced under five weights per yard. Commenting upon these and other figures there given, Mr. Holley stated as the primary object of his paper, " to show that,, while this multiplication of rail-patterns is an annoyance and an expense to rail-makers, it is a source of immense loss to railway companies." Since 1876 the increase in gross annual tonnage upon our leading lines has been very great, and has been accompanied by an increase of wheel-loads and running-speeds. As the average weight of the rails of 1876 was by no means excessive, the growing deman Is of traffic have slowly driven the roads toward stiffer sections, inaugurating a movement that now promises to become epidemic. In 1876 a 67-pound rail was a first-class equipment; to-day everything under 75 pounds is light, and many 80's are coming into use. European practice has long been heavier than ours; in part because the higher cost of sleepers has led to an average of 3-feet spacing, instead of two-feet as with us. The old 84-pound double-header, and Sandberg's 80- and 89-pound rails, respectively 51/4 inches and 591/2 inches high, are reported common on English roads; and he is strongly advocating the general adoption of the 100-pounder shown in Fig. 7, with what success I have not learned, except that the Belgian government has ordered a lot. Mr. Sandberg points out the undesirability of frequent changes of pattern, and the recent rapid growth in traffic-requirements; prognosticates a continuance of this

Jan 1, 1887

By Hall K

The Osborne copper gold mine, 100 per cent owned by Placer Pacific Limited, is situated 195 kilometres south east of Mount Isa. The orebody is broadly categorised into three main ore zones; oxide, transitional and sulphide copper. Copper oxide

Jan 1, 1997

By P. Pietrokowsky

RECENTLY a comprehensive investigation of the various sigma binary alloys was published by Duwez and Baen.1 It was shown that the following conditions are necessary for the formation of the sigma phase: (1) the difference in atomic diameters of the two alloying metals must not be more than about 8 pct; (2) of the two elements which form sigma, one must exhibit a body-centered cubic structure while the second metal must be face-centered cubic, at least in one of its allotropic forms. In addition, a tetragonal unit cell was proposed and powder patterns of six sigma phases were indexed for d spacings greater than 1.640 kx. Since the indexing, based on tetragonal symmetry, led to only fair agreement, the possibility of sigma being orthorhombic was investigated. Various methods for indexing orthorhombic powder patterns are de- scribed in the literature.' The method used in this investigation was a graphical examination of the differences in values of sin' 9 for the adjacent lines of the powder diffraction pattern. This method led to a complete indexing of the Cr-Co (60-40) pattern. Because of the strong similarity between the various sigma alloys, it was then possible to assign indexes to the patterns of Fe-Cr (50-50), Fe-Cr-Mo (30-30-40), Fe-V (50-50), Co-V (50-50), and Ni-V (50-50). The values of sin' 9 and indexes of the six sigma alloys, together with visually estimated intensities, are presented in table 1. In general, the similitude between the six patterns is quite good. For spacings greater than 1.75 kx a few differences are noticeable. In the Ni-V pattern, no (320) exists and the two strong lines (030) and (031) are separated by only two lines of lower intensity, unlike any of the other sigma patterns. However, very little is known about the Ni-V phase diagram and it is possible that the equal atomic percentage composition in this system lies in a two-phase region. At lower spacings there is a close analogy between the patterns. The planes

Jan 1, 1951

By W. Tovote

This paper is based upon 12 years' experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coördinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, due to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining states. Possible Systems of Classification By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that are most striking in their uniformity. 1. The "Desert province," extending roughly from Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and down into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows. 2. The "Yavapai schist" province, similar to the one first mentioned, consists of metamorphosed basic and semi-basic rocks. It lies in northern

Jan 1, 1920

By Dermot Ross-Brown, Brian Stimpson

The use of point load test data by the authors to estimate rock mass cohesion is a very ingenious approach. It must be emphasized that this estimate is indeed only an estimate since the point load strength index employed to predict the uniaxial compressive strength (and subsequently predict the cohesion) is likewise only an estimate.

Jan 11, 1979

By Donald P. Richards

The use of point load test data by the authors to estimate rock mass cohesion is a very ingenious approach. It must be emphasized that this estimate is indeed only an estimate since the point load strength index employed to predict the uniaxial compressive strength (and subsequently predict the cohesion) is likewise only an estimate.

Jan 1, 1980

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By M. G. King

In 1982, Asarco operated six smelters and refineries producing primary copper, lead, zinc, silver and gold. At that time Asarco was still reliant on its custom smelting and refining roots and mined only 25% of its smelting and refining capacity for copper and 10% of its lead smelting and refining capacity. By 1992, Asarco had been reshaped to become largely an integrated primary metal producer operating four smelters and three refineries. Zinc is no longer refined and the mining capacity has been increased to meet 100% of copper smelting and 50% of lead smelting needs. Only one custom smelter is in operation. This paper describes the metallurgical changes and challenges which have occurred in this restructuring of Asarco's operations while maintaining Asarco's position as one of the largest non-ferrous metals producers in the world.

Jan 1, 1993

By Yu-ren Jiang

Novel compounds of hydroxycarbamoyl carboxylic acids, including 2-hydroxycarbamoyl -3-methlcyclohexane carboxylic acid (HCMC), 2-hydroxycarbamoylmethyl decylen-4-yl carboxylic acid (HCDC) and 2-hydroxycar-bamoylmethyl tridecylen-4-yl carboxylic acid (HCTC) were synthesized. The flotation behaviors of diaspore, kaolinite and illite using these compounds as collectors were investigated. The flotation results revealed that the floatability of the minerals was, in descending order, diaspore and kaolinite, followed by illite, and the ability to collect the minerals was, in ascending order, HCMC and HCDC, followed by HCTC. At a dosage of 2×10-4 mol/L, both HCDC and HCTC show a strong ability to collect diaspore and a weak ability to float kaolinite and illite. The flotation recovery of diaspore is over 90% and that of kaolinite and illite less than 30%. Moreover, Fourier transform infrared spectroscopy (FTIR) spectrum and zeta potential, as well as the adsorption amount, indicated that the adsorption interaction between HCTC and diaspore was primarily a kind of chemisorption in the form of chelate rings, while the interaction between the collector and aluminosilicate mineral was dominated by physisorption. It was concluded that the novel hydroxycarbamoyl carboxylic acid compounds are highly selective collectors for the flotation of diaspore vs. aluminosilicate minerals.

Jan 1, 2011

By Briggs D

Comparing the results of a plant trial by averaging performance measures collected during the trial with measures collected before and after the trial is often quite subjective because of the impact of natural variation on the process. This is

Jan 1, 1997

THE morning session on mining methods with R. M. Raymond as chairman was devoted mainly to papers on explosives and the discussion of these papers. A paper on the numerical index of the re-sistance which rocks offer to the penetration of a drill bit was also read. The first paper, "Relation Between the Oxygen Bal-ance and Propulsive Strength of Eight Gelatin Dynamites" by G. St. J. Perrott, N. A. Tolch and J. E. Crawshaw, was presented by Mr. Perrott, super-intendent of the Pittsburgh Experiment Station of the U. S. Bureau of Mines. In this paper which is the beginning of a series of publications on explosives, Mr. Perrott stated that the attempt was made to put down in quantitative form the facts which have been known to explosive engineers for a long time. Eight samples of 40 per cent gelatin dynamite, with oxygen content varying from + 15 to - 36 per cent of the theoretical amount necessary to form complete combustion with all of the combustible elements were tested. The experimental work showed that a bal-anced explosive did not give the greatest propulsive strength-but the most favorable range was from - 8 to - 25 per cent oxygen. The experimental work also brought out the fact that the wrapper of a stick of dynamite enters quite completely into the explosive reaction, and gelatin dynamites from which the wrapper had been removed developed less strength than the a same explosive with the wrapper. The second paper, "Effect of Oxygen Balance of Gelatin Dynamites on the Gaseous Products of Det-onation," by G. W. James and G. St. J. Perrott, was also presented :by Mr. Perrott. The first portion of this paper is given over to a discussion of the relative merits of different types of apparatus for testing and analyzing the combustion products of dynamites. Three types were used (1) the Bichel gage, (2) the Crawshaw-Jones apparatus and (3) the Hercules tank. All three of these types were used in testing dynamites whose oxygen balance varied from-35 to + 6 per cent.

Jan 3, 1928

CONTENTS PAGE FULTON, CHARLES H., and READ, J. BURNS-A New Roasting Furnace for Zinc Flotation Concentrate. Discussed by Charles H. Fulton, Arthur S. Dwight, B. M. O'Harra, Kurt Stock 1 STOCK, KURT.-Redistillation of Zinc. Discussed by G. E. Dalbey, Kurt Stock.. 3 BEASLEY, F. E.-High Zinc in Lead Blast-furnace Slags. Discussed by R. C. Canby, R. L. Lloyd, C. R. Haywood, G. E. Dalbey, A. S. Dwight, E. P. Mathewson, A. L. Walker, B. M. O'Harra, and C. P. Linville 4 STEELE, E. W.-Application of Pulverized Coal to Copper Refinery Furnaces. Discussed by F. R. Pyne, E. P. Mathewson 11 LINVILLE, C. P.-Recovery of Arsenic and Other Valuable Constituents from Speiss. Discussed by C. R. Hayward, C. P. Linville, G. E. Dalbey, A. S. Dwight, Edward F. Kern, Karl Eilers, E. P. Mathewson 12 A New Roasting Furnace for Zinc Flotation Concentrate Discussion of the paper of CHARLES H. FULTON and J. BURNS READ, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1362-D, with MINING AND METALLURGY,. October, 1924. G. E. DALBEY, East Berlin, Conn. What would be the, effect on the formation of sulfates of an increased water vapor content in the roasting gases? CHARLES H. FULTON.-I cannot answer that from our experience. The question of the formation of sulfate in the roasting of zinc is mainly one of temperature and the concentration of S02 and S03 in the gases. We found we could roast almost completely to sulfate if the concentration was kept at the proper point. We, however, did not care to do this because we wished to make a 5 to 6 per cent. S02 gas for sulfuric-acid work. The sulfating of the zinc oxide in the proper concentration of gases goes on very rapidly. There are certain places in the furnace system such as the Cottrell and in a part of the dust chamber in which the roasted

Jan 6, 1925

The mineral resources of Hamersley Iron are structurally complex with fluctuations in mineral chemistry. Besides orebody charact- eristics, mineral recovery is also affected by stringent product quality demands from the competititve steel industry. Under such conditions, a geological ore reserve estimate has little meaning because it is unqualified and presupposes the defini- tion of ore. A system was developed in Hamersley - the Mine Planning Technique - to optimise recovery from available resources. This incremental planning method reduces a geological reserve statement into a simple, logical sequence of events. While there are limitations in the method used, the benefits are enormous. Among its' numerous applications, the schedule - the end product of the technique - plays an important role at Management level in decision making and policy formulation on all aspects of resource exploitation.

Jan 1, 1979

By C Gourdon

The present study concerns a new type of mixer-settler unit where coalescence is promoted by means of the phase inversion method (MSPI). Using two different systems (alkaline etching solution û LIX 54 in kerosene and acidic aqueous solution û LIX 984 in kerosene) the influence of the total flowrate, the A/O phase ratio and the hydrodynamic conditions in the nozzles of the scattering device on the extraction and separation efficiencies are studied. Two modes of operation are clearly outlined and a theoretical model predicting the separation efficiency is proposed and compared to experimental results. A comparison between mixer-settlers with classic decanters and the MSPI unit has demonstrated the advantages of the latter where throughputs in the range 20 -25 m3.m-2h-1 can be easily realised.

Jan 1, 2000

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By J. B. Clark, F. N. Rhines

brittlement or notch sensitivity progressively increases. Further, in contrast to results obtained with the impact test, the notch strength for the large specimens does not reveal a 500°F embrittlement range. The notch sensitivity as determined with the 0.3-in. specimen of 4340 steel given the stepped austenitizing treatment has been discussed elsewhere. This quantity as measured for the 1.1-in.- diam notch tensile test and given in Fig. 3, is taken to signify that reduced notch sensitivity is encountered in the 600" to 800°F tempering range for specimens given the stepped austenitizing treatment. The stepped austenitizing treatment may, there- fore, be of use in promoting deeper hardenability for a 4340 steel while at the same time giving reduced notch sensitivity in the high-strength range in which this steel is now being used. Acknowledgments The work reported was supported by the U. S. Navy Bureau of Aeronautics. The authors are indebted to the Bureau of Aeronautics for granting permission to publish results of this research and to N. E. Promisel, H. Hessing, and J. Maltz for their interest.

Jan 1, 1958

By M. Charles Gilbert

Basement rocks in southern Oklahoma are divided into two groups. One group is the Lower Cambrian Wichita Igneous Province, a diverse igneous suite that crops out in the western Arbuckle Mountains and in the Wichita Mountains. These largely bimodal igneous rocks were emplaced in an intracratonic-rift environment. The other group, the older, is a set of Precambrian rocks of the Eastern Arbuckle Province, yielding ages between 1,350 and 1,400 Ma, exposed in the core of the eastern Arbuckle Mountains. These are deeply eroded mesozonal granitic rocks and associated granitic gneisses cut by numerous dikes ranging in composition from diabase to rhyolite. The southern Oklahoma igneous rocks have long been utilized mostly as dimension and crushed stone. Most of the early quarries were in granite of various red hues for monuments and facing stones. Large crushed-stone quarries are now exploiting both granite and rhyolite, which is used chiefly as aggregate and railroad ballast. The exposed basement rocks in Oklahoma represent an underdeveloped and accessible resource.

Jan 1, 1999

By Wankun Wang, Shixing Wang, Jinhui Peng, Zebiao Zhang

"Germanium leaching from germanium dust and fume was carried out using sulphuric acid. Response surface methodology (RSM), based on a five level, four variable central composite design (CCD), was employed to obtain the best possible combination of liquid/solid ratio (Xi: 2-10), leaching time (X2: 1-5 h), sulphuric acid concentration (X3:3.15-15.75mol/L) and leaching temperature (X4:50-90 *C) for germanium leaching. The obtained experimental data were fit to a one-order polynomial equation using multiple regression analysis and also analyzed by analysis of variance (ANOVA). The 3-D response surface plot and the contour plot derived from the mathematical models were applied to determine the optimal conditions. The optimum extraction conditions were: liquid/solid ratio of 10, leaching time of 1 h, sulphuric acid concentration of 15.75 mol/L, and leaching temperature of 87.8 'C. Under these conditions, the germanium leaching extent was 65.14%, which is in close agreement with the value predicted by the model. The samples were characterized before and after leaching using X-ray diffraction (XRD).IntroductionResponse surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [1-15]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the vital controllable factors are identified. It is also used to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected [6], The process optimization of the sulphuric acid leaching of germanium from germanium dust and fume has not been reported in the literature. Hence the present work intends to assess the effects of variables such as liquid/solid ratio, leaching time, sulphuric acid concentration and leaching temperature and to identify the optimum conditions using RSM. The characteristics of sample before and after leaching are assessed using the advanced analytical instruments such as X-ray diffraction (XRD)."

Jan 1, 2012