Search Documents

By Artur Frederico Fonseca da Cruz, Jael Moutinho dos Santos

The problem of iron ore sticking and premature wear on screening rolls on balling systems is recurrent. The importance of the "screening" function of the roller classifier is fundamental, since in perfect conservation state and operation it is possible to ensure the performance improvement of the most expensive phase in the pelletizing production chain, the thermal processing. The present works target is the identification of possible causes of iron ore adhesion in classifier rollers and develop a methodology to evaluate and quantify the iron ore sticking mechanism on the classifier surface. For this purpose, iron ore and additives were collected at four different pelletizing plants in terms of iron ore origins and process flows, three different rollers were chosen for testing around the adhesive energy at the iron ore mixture/rolls surface interface. As results, it was possible to construct methodologies to evaluate the aggregability, it was observed the importance of "specific moisture" definition and knowledge on the adhesive energy increase, besides presenting the better performance of rolls with tungsten carbide coating than other evaluated.

Oct 1, 2019

The Year Book of the Institute is mailed with this Bulletin. Its membership lists, both alphabetic and geographic, are corrected to Jan. 1, 1918, but its list of officers is revised inn accordance with the elections in February, 1918. The amendment to the Constitution, relating, to qualifications for membership, adopted at the same time, is also inserted in its proper place. We would call attention to the Honor Roll, heading the list of membership. This includes the names of those whom we know (in February, 1918) to be on active military duty, as well as those who are rendering emergency service to the Government in other branches. We are aware that the list is not complete, and shall be grateful for information as to any omissions or corrections. Because of the rapid movement of the military members, their addresses have been omitted from the alphabetic list. Mail addressed to such members, and sent to the office of the Institute, will be forwarded to the best of our information at the time.

Jan 3, 1918

By E. S. Moffat

Members of the Institute who have visited the works of the Lackawanna Iron and Coal Company at Scranton, will remember the exposure of a large vein of anthracite coal in the rocky bank on the south side of Roaring Brook, near the blast-furnace. The vein is quite flat, and is exposed to view for several hundred yards along the banks of the brook, a few feet above the surface of the water. It is some ten feet in thickness, and is known as the Big Vein. At a point just opposite the blast-furnace, much of the coal from this vein was mined out many years since, the usual pillars being left to support the overlying rock and drift, which are here some twentyfive to thirty feet in thickness. Over thirty pears ago fire was communicated from an ore-roasting pile on the surface of the ground at this point, through an old shaft, down to the refuse and pillars which had been left in the mine

Jan 1, 1887

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) General manager .for a pyrite mine in Virginia, with experience in the mining and particularly in the washing of pyrite, required. Salary at start, $250 per month with perquisites. No. 28. Assayer and cyanide man for a Costa Rica plant. Salary $100. No. 29. Mine manager to develop gold-mining property in Witwatersrand, Transvaal. Salary £2,000 to £4,000, according to the experience and ability of the engineer. No. 31. Mine superintendent for a mine in Arizona containing copper, gold, silver ore. Will have entire charge of operation and development. Salary to start, $200 per month with perquisites. No. 32. .Mining engineer to make complete report and suggest necessary machinery for development and operation of a placer property; also to examine a copper property. Both properties in Peru, South America. No. 34.

Jan 4, 1915

By Stanley Bunk

The fluidized bed was invented by Fritz Winkler of Germany in 1921. The first application in the U.S. was in the development of the fluidized bed catalytic cracking of petroleum in 1942. Today, fluid bed cracking reactors are an integral part of every oil refinery. When fluid bed technology was first considered for applications outside the petroleum industry it was recognized to have uniform temperature, close control of the gaseous atmosphere and excellent mixing between solids and gases. Roasting of sulfide ores and concentrates was an obvious match. The first application was a single stage roaster for gold refining in 1947. There have been over four hundred commercial fluid bed roasters built and operated successfully in the four decades since the fluid bed was invented. There are three general categories of roasting applications. The largest number of roasters fall into the dead roasting category which includes gold ore roasters. The other categories are sulfating roasters and partial roasters (Reference 1).

Jan 1, 1990

By J. V. Batty, K. C. Dean, H. D. Snedden, W. J. Long

As a part of the investigation of strategic-mineral deposits in the United States under the Strategic Minerals Act, engineers of the Bureau of Mines examined and sampled numerous deposits of fluorite ore from Utah. From those deposits that warranted further investigation, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory ore-dressing studies of the fluorite ores submitted. Test work was done on samples from four properties in the Washington Mining District, Beaver County; two properties in the Star Mining District, Beaver County; one property in the Wah Wah Mountains, Beaver County; and three properties in Tooele County, Utah. In general, the Washington District ores were found amenable to concentration by flotation for the production of acid-grade fluorspar. None of the other ores were beneficiated to acid-grade, but several were amenable to concentration for the production of metallurgical-grade fluorspar concentrates.

Dec 1, 1947

By J. V. Batty, K. C. Dean, H. D. Snedden, W. J. Long

As a part of the investigation of strategic-mineral deposits in the United States under the Strategic Minerals Act, engineers of the Bureau of Mines examined and sampled numerous deposits of fluorite ore from Utah. From those deposits that warranted further investigation, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory ore-dressing studies of the fluorite ores submitted. Test work was done on samples from four properties in the Washington Mining District, Beaver County; two properties in the Star Mining District, Beaver County; one property in the Wah Wah Mountains, Beaver County; and three properties in Tooele County, Utah. In general, the Washington District ores were found amenable to concentration by flotation for the production of acid-grade fluorspar. None of the other ores were beneficiated to acid-grade, but several were amenable to concentration for the production of metallurgical-grade fluorspar concentrates.

Dec 1, 1947

By G. Roy Chaudhury

Adsorption techniques are comparatively low cost and effective for treatment of arsenic contaminated drinking water. Various adsorbents such as alumina, ferrihydrite and manganese ores have been used, but there has been little investigation of modifying the structure of ferrihydrite to improve its adsorptive efficiency of As(III) and As(V). In the present study the incorporation of manganese oxide into the ferrihydrite structure was carried out and the prepared materials used in arsenic adsorption experiments. The compounds were X-ray amorphous, but TGA/DTA and FTIR analysis showed some structural characteristics. Sorption studies reported in this paper indicate the excellent arsenic removal properties of the manganese/iron compounds with a loading capacity of 0.3 mmol/g. Adsorption follows first order kinetics and the results fitted to adsorption and mass transfer models. Arsenic levels in water containing 1 mg/L As(V) were reduced by 50% in 20 minutes and 90% in 60 minutes using 1 g/L manganic ferric oxyhydroxide.

Jan 1, 2003

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Abstract-Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environment control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m, (24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1- ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky Fluorspar mining district, and late Paleozoic, erosional unconformities in northeastern Kentucky.

Jan 4, 1978

By Keith G. Wallace

Small scale open pit mining of the Lucky Mc property in the Gas Hills district of central Wyoming was started in the spring of 1954 and the first uranium ore went to Vitro's mill in Salt Lake City that July. Shortly after mining started it became apparent that accurate ore control for mining purposes would be an absolute requirement. A systematic drilling program was initiated in the spring of 1955, and has been continued up to the present time. Two main mining areas have been developed. Mine 1, at the site of the original ore discovery in the Gas Hills, covers a mineralized zone roughly 600 x 2800 ft. This orebody was outlined and developed by drill holes on 50-ft centers. Approximately 1300 holes were drilled in the area before preliminary mining plans were made and mineable reserves calculated. Reserve estimates were based almost entirely on chemical assays of drill hole samples.

Jan 10, 1958

By Gunther L. M, Rich N

Remapping of the Burdekin Basin has resulted in the subdivision of the three formations (megafacies) previously recognised in the Late Devonian Dotswood Group. Nine dominantly volcaniclastic facies are now identified within the three megafacies, representing coastal plain, floodplain lake, alluvial plain, ephemeral lake and alluvial fan depositional environments. The Dotswood Group was deposited during a major regressive phase that began at the end of the Givetian, continued throughout the Frasnian and ended in the early Famennian.The proposed depositional model completes a southeasterly progradation of coastal plain facies over shoreline and nearshore marine facies established in the underlying Fanning River Group. Uplift and associated acid-intermediate volcanism to the south of the Burdekin Basin, resulted in the deposition of a volcanogenic alluvial fan facies locally preserved along the southwestern margin of the basin. Tuffs and ?ignimbrite were deposited in widespread floodplain lakes which lay behind the coastal plain. An alluvial plain traversed by southward flowing rivers, formed the northern margin of the basin.

Jan 1, 1990

By A. D. Taylor

In recent years there has been an increasing effort to attract students into engineering. Obviously, the effort is necessary because young people find the image of the engineer unattractive. Some of the things they find unattractive are real, some are not, and part of the problem is too little knowledge of the field. First, I would like to comment on some of the ideas which appear to be justified. Engineering is a difficult course of study. True, and nothing can or should be done to change this. The education is continually being improved, but it is unlikely to be made easier.

Jan 1, 1970

By D. Lenartowicz, K. R. Alexander, M Collings

Cosmo Howley is a gold deposit in the Northern Territory of Australia. The geology is complex and the input of geological data is an important part of the grade control process. As the geology of the deposit has become better understood, grade control and mining techniques have evolved to meet the changing circumstances. Present grade control depends on the use of angled blast holes, 21/2 benches and selective mining. Data is processed on site using 2 386 PC's running Surpac software. An environmental protection programme is employed, including soil stripping and stockpiling, sulphide waste containment and water quality monitoring.

Jan 1, 1989

By Phillip Philbin, Frank E. Senftle

A field neutron activation analysis technique suitable for determining uranium in ores has been tested. The method is based on the measurement of the 74.7 keV gamma ray from 'U. When the thorium/uranium ratio is greater than one or the vanadium is greater than 1%, a low uranium analysis is obtained. No satisfactory correction for thorium has been found, but a correction for vanadium can be deter¬mined. For ore containing greater than 0.01% uranium, the uranium can be deter¬mined with an accuracy of about 10% which is quite adequate for a field exploration technique.

Jan 1, 1972

By Eustáquio de Souza Baêta Júnior

O aço delta-TRIP é um conceito recente, sendo desenvolvido nos últimos dez anos com o intuito de aliar boa resistência mecânica e ductilidade. Este aço é multifásico, contendo ferritas d e a, austenita, bainita e/ou martensita. O efeito TRIP (Transformação Induzida por Plasticidade) é influenciado pela proporção entre essas fases, que por sua vez tem relação com a quantidade dos elementos de liga. Este trabalho busca uma composição química que permita adequada proporção entre as fases, otimizando as microestruturas através de métodos computacionais. Essas microestruturas são projetadas para conter na temperatura do eutetóide entre 10% e 50% de austenita, entre 10% e 70% de ferrita alfa e entre 20% e 80% de ferrita delta. O software ThermoCalc foi utilizado para prever as frações dos microconstituintes, gráficos da variação dos elementos de liga pelas faixas de interesse dos microconstituintes foram utilizados para mapear cada condição que leva a microestrutura desejada. Resultados indicam que o volume das fases projetado é encontrado para determinadas proporções entre os elementos de liga, maiores concentrações de Al e Nb combinados com C permitem a ocorrência ou não de carbonetos e outras fases em menores quantidades.

Oct 30, 2017

By Fred W. Menzl, Raymond E. Sutton

GABBS, Nev., in Nye County, is 140 miles southeast of Reno and about 31 miles north of the Southern Pacific railroad at Luning. The townsite lies at the eastern edge of Gabbs Valley, and plant and quarry operations are in the foothills of the Paradise Range at elevations from 5000 to 5900 ft. Hard-surfaced roads connect with main U. S. high- ways on the north and south. Historical Background: Brucite, a magnesium hydroxide mineral, was discovered in the Gabbs area in 1927 and magnesite, the magnesium carbonate, was found later on claims originally staked and worked for the tungsten mineral scheelite. The brucite is on a granodiorite contact and the magnesite is usually some distance away from the granodiorite

Jan 7, 1957

This paper looks at the problems associated with surface settlements and other subsidence effects from the underground extraction of coal in relation to consent applications under the Resource Management Act. The main features of subsidence are examined with respect to identifying the adverse effects as defined under the RMA. Particular attention is paid to sites where little or no data is available as in the case of greenfield sites or at mines where new or different mining methods are being introduced. In these situations it is not possible to make accurate predictions of settlements or strains and therefore other factors need to be considered. The long term effects which might occur post mining are examined in relation to mitigation and management options.

Jan 1, 2003

By M. Y. Xia

In this paper, based on the Theological tests of the interface between clay and concrete, an interface Theological model is proposed and is used in the finite element analysis which takes soil as viscoelastic mass and Theological effect of the interface between diaphram wall and ground into consideration. Its results are compared with those without an interface element, without considering the relative creep displacement. Close attention is paid to the variation of wall with time under the condition of various interface shear stiffness and viscous sliding coefficient, and their effects on the wall bending moment are primarily verified in the paper. The change of wall bending moment with time, trench heave and wall displacement in different excavation depth, bracing position, parameters for soil are also studied.

Jan 1, 2010