Search Documents

Heavy medium separation is widely used because of the precision of separation achievable and the flexibility of control. Good design is manifest in the eventual achievement of the operational objectives. These objectives which take account of the assessed quality of raw feed, market requirements and production cost levels need to be carefully prepared and realistic.

Jan 1, 1987

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

By R. W. Smith, D. Clare

The removal of metals from an acid mine drainage (Leviathan Mine, Alpine County, California) water by precipitate flotation was investigated. The Leviathan waters vary from about pH 4.0 to pH <2.0and contain from about 2,000 to about 12,000 ppm SO42-.The main multivalent metals present in solution are Fe, Ca, Mg, Al and Mn. Both Cu and Co are present in small amounts. The pH was adjusted with lime. The collector used was either sodium oleate or tall oil. The sodium oleate was used as a function of pH to establish optimum flotation conditions and the tall oil was used only at the optimum pH. Dow Froth 250 was used as a frother. In some test additional Cu was added to the system. Excellent recovery of Fe and Cu were achieved at optimum pH. The process achieves results comparable to precipitation and filtration without as much problems with screens blinding because of less material to filter.

Jan 1, 2004

By AIME AIME

COUNCIL* PRESIDENT OF THE COUNCIL. JAMES F. KEMP NEW YORK, N. Y (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, C; L.. R. V. NORRIS WILKES-BARRE, PA.. GARDNER F. WILLIAMS WASHINGTON, D. C.. (Term expires February, 1913.) KARL EILERS NEW YORK, N. Y.. WALDEMAR LINDGREN WASHINGTON; D. C.. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Nov 1, 1912

By Fyodorov A. N, Sorokin M. L, Komkov A. A

The Vanyukov Process is a bath smelting technology, that has been investigated for over 25 years and since 1977 has been in use on an industrial scale. Results of trials that have been carried out at the various pilot facilities over the past 15 years are considered in this paper. Both the main process aspects, design of the pilot furnaces and metal distributions are presented for consideration. Experience of the smelting of copper, copper-nickel, copper-zinc, nickel, lead, and pyrite concentrates is analysed.

Jan 1, 1992

By David Martin Menne

Carbon or attrition can be expected to be affected by • Agitation power • Vessel volume • Carbon and Suspension densities • Kinematic viscosity of slurry • Carbon particle size • Impeller diameter • Impeller rotational velocity • Fractional carbon [volume] concentration • Gravitational constant

Jan 1, 1995

By Callcott R

Prediction of raw coal size distributions and those generated by processing are examined using spreadsheets and the matrix analysis of breakage processes. Run of mine coal size distributions are predicted from the lithotype properties using a

Jan 1, 1998

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By Duane H. Haley

The century we live in has been an eventful time for the Third World, particularly the country of Peru. Although it will take one or two generations more to see its end and fully evaluate its scope, it is already clear that during the twentieth century, Peru has entered a dynamic industrial, economic, social, and political revolution. This century has seen the end of old governments, and the introduction of reforms which radically change complex traditional patterns. It also has marked the beginning of an era in which the government has elected to undertake, as a national effort, most of the future economic growth of Peru. For the most part, large multinational mining companies, which have helped to discover and put into operation large mineral and ore deposits in Peru, have been sympathetic toward this philosophy. Most big foreign companies, in addition to capital, brought with them to Peru an efficient technology, modern management, and an effective organization for the further processing, sales, and distribution of refined commodities. Nationalization of all basic resources, including mining, is the, trend-not, it is hoped, to the detriment of established technology and production.

Jan 1, 1974

By Paul Hosford, B. Thrall

There has been a surge of exploration activity and interest in mineral properties located in cold Northern climates, with gold and copper properties as the two most attractive targets. There are already a number of mining operations located in the Arctic, for example, Red Dog, Polaris, and Lupin, all located in the Canadian Arctic. The logistics of sustaining operations, the engineering design and construction methods for such inhospitable regions are now relatively well understood. However, at least three of the proposed new mines in the Yukon Territory, Canada are designed to be heap leach operations. Rescan Engineering has recently completed Feasibility studies for two heap leach operations in the Yukon, one of which, the Brewery Creek Mine, is now in operation. The purpose of this paper is to explore some of the engineering and operating concepts that have been developed to make heap leaching an appropriate process method for gold recovery in a cold climate. Many of the readers will be familiar with the general and specific details of heap leaching, and it is not the intention of the authors to deal with any of the established "do's" and "don'ts" that have been addressed in numerous previous papers, but only with those pertaining to cold weather operations. This paper also examines these design concepts in specific relation to the results of the first winter's operation at Brewery Creek Mine, the first "far" North heap leach operation.

Jan 1, 1997

The excessively high cost of production in underground coal mines has made the survival of many coal mines around the globe economically non-viable. The global competitive coal market speaks itself of the desirability of a lower operating cost in conjunction with a higher productivity performance, particularly in underground coal mines, and calls for an optimal production planning under a host of constraints. Such a task of optimal planning is not an easy exercise like that of traditional planning based merely on intuition, experience and subjective judgement. It essentially demands a thorough understanding of the complex interaction of mine sub-systems for judicious application of optimisation tools and techniques available with operations research. A few large mines around the globe have made an effective use of a sizeable number of operations research packaged programs for optimal decision-making (Grayson, 1989). The success of practical applications of operations research techniques made in a variety of mining problems in large mines in different parts of the world will hopefully make inroads to smaller mines in years to come. The present paper is an addition in the series of such applications of operations research tools to mining problems, particularly with reference to an underground coal mine in India. The paper is based on research work (Jawed, 1990) and deals with the development and use of a mathematical model for production planning in underground coal mines under multiple objective environment subject to a host of constraints.

Jan 1, 1995

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By B. Hoare, H. M. Hill

"SYNOPSISTailings volumes, disposal systems, effects of dam failures, construction materials, and concentrator process water volumes are discussed. Earth dams and tailings dams are discussed in detail. Some of the fundamentals of soil mechanics relating to earth dams are presented. Brief notes on optimization are presented. The development of a triplex meter for earth dam instrumentation is described. The advantages of the hydro-cycloned dam over the spigotted dam are outlined. INTRODUCTIONThe realistic and responsible recognition of the pollution problem, combined with the grossly increased volumes of waste material from large modern mining operations, has emphasized the demand for safe tailings dams at minimum cost.Tailings may be defined as the waste material from a mining operation after the process of concentration in which the minerals have been extracted for commercial use. The present revenue from the Canadian Mining Industry is slightly over $4,000,000,000 per year and it is estimated that the quantity of tailings produced exceeds 300,000,000 tons annually. In many instances, the volume of tailings from a mining operation is greater than the volume of crude ore mined on account of the small quantity of valuable mineral recovered during concentration, and on account of the ""swell factor"" resulting from the processes of drilling and blasting, crushing, and grinding of the crude ore. Some of the larger mine tailings deposits contain over 200,000,000 cubic yards and the associated tailings dams are among the largest man-ma.de structures in the world."

Jan 1, 1970

By Edward Walsh

The difficulty of securing for experimental research the actual conditions to be found in practice very frequently deters many from engaging in such work. Probably no metallurgical operation is more difficult to imitate in the laboratory than the blast-furnace process. So many complex reactions take place within the furnace, under such varied conditions of time and temperature, with innumerable mechanical, physical, and chemical mutations, that while the results reached may approximate those obtained in practice, there is always something wanting. Much work of this kind has, nevertheless, been done, and is now being undertaken. We are indebted to the bold minds who have attempted it for our present real knowledge of the blast-furnace process. Not that those who have performed series of experiments at a few given temperatures can claim the honor. It required more than this—the ability to make a summary of all preceding experiments, to supply those which were wanting, and to confirm those that were doubtful. Sir I. Lowthian Bell, whose able papers before the Chemical Society and the British Iron and Steel Institute (forming the basis of his great work, The Chemical Phenomena of Iron-Smelting) has

Jan 1, 1889

By J. L. Floyd

The Trapper Mine is a large surface coal operation located in northwestern Colorado US. The coal seams at the mine dip an average of 8 degrees so, historically, their dragline pits have been orien-tated parallel to the dip of the coal seam to balance stripping ratios. However, the mine plan in the future G and Z pits is designed to take advantage of pit orientations that are parallel to the strike of the coal. During the initial presplit and cast blasts in G pit, significant slope damage occurred. This damage included the opening of joints and tension cracking. There was also block movement directly above the L coal seam, which is the main plane of weakness in the slope. A detailed site evaluation was conducted to develop specific blast design modifications to protect the slopes during future blasting. The modified de-signs successfully controlled vibration levels during the blasting of the Z pit box cut. This paper includes a review of the blast vibration related factors that influence slope stability along with a detailed discussion of the field tests and design modifications developed.

Jan 1, 2004

By M. S. Enders

The McDonald gold deposit is located in the upper Blackfoot Valley in Lewis and Clark County in west-central Montana, about 65 km (40 miles) northwest of Helena and 13 km (8 miles) east of Lincoln (Fig. 1). The McDonald project area covers about 20.7 km2 (8 sq miles) of elevated terrain on the north side of the Blackfoot Valley. The Blackfoot River lies 1 km (0.6 miles) south of the McDonald deposit. East Butte and West Butte rise 300 m (985 ft) above the Blackfoot Valley to an elevation of 1,750 m (5,740 ft). They conveniently divide the area into two parts. The Seven-Up Pete Joint Venture (SPJV) is a partnership between Phelps Dodge Mining (72.25%) and CR Montana, a subsidiary of Canyon Resources (27.75%). SPJV controls about 83 km2 (32 sq miles) of mineral and surface rights in the Lincoln area. The McDonald project is on state-owned and private land. The joint venture has conducted exploration since 1989 at the Seven-Up Pete, McDonald and Keep Cool areas (Fig. 1).

Jan 1, 1995

By A. V. Tarasov

The insufficient scientific and technical level of a number of operations in the nonferrous metals industry encourages development of new processes and equipment, including smelting in liquid bath, flame-type sparged smelting unit for combined processes, electrothermal process with the use of alternating current (PDF furnace), electrothermal processing of complex raw materials and intermediate products at nonferrous metallurgical plants, etc. One of the most important aspects for development of new processes and equipment in the Gintsvetmet Institute is their environmental safety. Special attention is paid to environmental protection measures, which is also of important economic and social significance. This refers also to a complete extent to processing of reserves of man-made raw materials and wastes available at the existing operations with the use of innovative techniques ensuring not only resource conservation and environmental protection, but also abatement of negative impact on the nature due to accumulated industrial and domestic waste, reclamation of the land used for waste disposal and recycling of nonferrous metals. Technologies and equipment developed in the Gintsvetmet Institute and based on electrothermal processes determine the prospects for ensuring more integrated usage of ores and man-made raw materials.

Jan 1, 2006

By S C. Goel

The Obuasi Mine in Ghana, West Africa is the largest producing gold mine in Africa, outside South Africa. The mine has changed from a mine producing from narrow vein, high grade quartz orebodies to a mine producing from wide, lower grade sulphide rebodies. Traditionally mining methods were cut and fill and sublevel caving. Now the preferred stoping methodologyis long hole open stoping. Transverse or longitudinal methods are both used, dependent on the orebody characteristics. The change has been technically, socially, economically and politicallychallenging and at times has tested the abilities of those responsible for the operation of the mine. However, the benefits have been many. Safety has improved significantly, ounces from underground have doubled. Productivityhas doubled and underground unit costs have reduced bya third. These achievements have allowed the Obuasi mine to staycompetiti ve in this time of falling gold price. During 1999 and 2000 a full review of the mining and processing operations was undertaken, and as a result, the mine is now in a phase of restructure. Efforts are being made across the mine to improve efficiencies and to reduce costs. The future for the Obuasi Mine is an exciting one.

Jan 1, 2000