Search Documents

By B. Whitmoyer, J. Tian, J. E. Sneckenberger, M. A. Jerabek, C. A. Chandler

A computational procedure has been developed to determine the lung volume function for the upper airways of the human respiratory system. This analytical procedure computes a person's partial lung volume from an experimental two-microphone acoustic measurement of the upper airway passages obtained through a molded tubular mouthpiece. The theoretical transfer function for the two microphone signals as well as the related acoustic impedance and reflection coefficient for the upper airways are calculated using two-channel spectrum analysis techniques. An inverse spectrum analysis scheme then converts the reflection coefficient to an impulse response from which the airway area function is extracted using an area recovery algorithm. Numerical integration of the upper airway area function yields the lung volume function for the upper airways of the human respiratory sysytem. A software program to accomplish this computation of human upper airway volumes will be described in this paper. Application of this computational procedure to the measured tracheal acoustic impedances of 15 human subjects will illustrate the program's capability toward early detection of lung dysfunction using a prototype clinical facility.

Jan 1, 1991

By R. F. Hewlett

All ore reserve estimates are based on some system for assigning an area of influence to each drill hole. Commonly used methods of calculation are the polygonal, triangular, statistical analysis, and cross-sectional. Each of these methods is based on different volumetric considerations and the weighting of grade with tonnage varies with each method. Because the characteristics of each mineral deposit are different, a preliminary survey of these characteristics should be made for each individual deposit to determine which method or methods should be used. In this project the several methods were not only compared with one another, but also against actual production records. Basic data was derived from a mined out portion of the Silver Bell pit near Tucson, Ariz. All calculation was carried out on a digital computer, and the first step was development of computer programs which would yield the desired information. The second step was the coding of input data into punched card form. Cost and speed of computer operation were measured, and these results are given with the computer program summaries on page 38.

Jan 1, 1961

By L. S. Darken, H. A. Wriedt

The equilibria at 1 atm total pressure and 600° to 1300°C (1112° to 2372°F) between gas mixtures with various partial pressures of the reactive constituents (principally sulfur dioxide, carbon dioxide, water vapor, oxygen or carbon monoxide, and hydrogen) and coexisting solid phases (groups variously including calcium oxide, calcium carbonate, calcium sulfide, calcium sulfate, iron, ferrous sulfide, and the iron oxides) are examined. Tables and charts show the combinations of temperature, oxygen activity, and carbon dioxide partial pressure under which the various groups of the solid phases coexist and the corresponding sulfur dioxide pressures. In the presence of calcium sulfide, calcium sulfate, and calcium oxide, the partial pressure of sulfur dioxide has a peak value at each temperature which increases from 101 atm at about 800°C (1472°F) to 1 atm at about 1200°C (2192°F). With water vapor present, hydrogen sulfide may predominate among gaseous sulfur compounds, particularly at low temperatures and oxygen activities; under all other circumstances considered, sulfur dioxide is the dominant gaseous sulfur-bearing species.

Jan 1, 1974

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers, and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties.

Jan 1, 1923

By Newton D

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers, and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties.

Jan 1, 1928

By Griffin P

The project is the result of a European Commission supported collaboration between Surpac Software International, the Technical University of Berlin, and the industrial partners Exploration and Bergbau GmbH (E+B) and Taylor Woodrow. The object

Jan 1, 1998

By E. B. Fitch

The operating behavior of liquid-solid cyclones is outlined, together with the nature and range of the process results obtainable, to serve as a background for engineers wishing to consider application of this new process tool.

Jan 3, 1953

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By E. H. Rennhack

THE presence of sufficient quantities of the inter- stitial elements, carbon, oxygen, and nitrogen is known to decrease sienificantly the room-temperature impact resistance of titanium. Hydrogen does not appear to affect impact strength unless present

Jan 1, 1959

By K. V. S. Sastry, V. P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite, and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in term of the compression strength, impact resistance (drop test), abrasion resistance, and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder wed. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1983

By Vantuil Manoel Thebas

A automatização do laminador Machine duo reversível de 8 toneladas passa pela determinação da força de laminação em seus cilindros durante processo de deformação da chapa metálica não ferrosa, o que se faz pela medição direta da força nos cilindros do laminador através de um sensor de força ou pelo uso de modelos matemáticos aplicados ao processo de laminação das ligas metálicas. O presente trabalho tem por objetivo o estudo dos modelos de Orowan, Ekelund e Bland & Ford aplicados à predição da carga de laminação de ligas metálicas não ferrosas. Amostras em barras chatas extrudadas com 6,35 mm (14/') de espessura da liga de Alumínio 6063-T5, com 300 mm de comprimento e 50,8 mm (2’) de largura, foram laminadas. Suas dimensões finais foram obtidas por uma escala de medição e paquímetro universal, sendo os dados tratados por rotinas computacionais especificamente desenvolvidas para a implementação dos modelos matemáticos citados. Os resultados deram conta de que a implementação dos modelos de Orowan, Ekelund e Bland & Ford através de rotinas computacionais podem ser muito úteis na predição da carga de laminação de ligas metálicas não ferrosas.

Aug 8, 2018

By Guilherme Santos Garcia

Este trabalho tem por objetivo avaliar a sinterização a plasma do alumínio com a utilização da técnica Active Screen, em comparação com o processo em forno resistivo. Foi utilizado pó de alumínio atomizado, com granulometria entre 30 e 100µm, sendo misturado junto aos pós cerca de 1% em massa de estearato de zinco como agente lubrificante. Foram confeccionados corpos de prova com 13mm de diâmetro e 10mm de altura. A compressão dos pós se deu através de uma prensa hidráulica, de ação simples, utilizando pressão de compactação de 600MPa. O tempo te sinterização foi mantido em 60min a temperatura de 500ºC, utilizando atmosfera de nitrogênio. Foram realizadas medidas de densificação, antes e após a sinterização, medição de rugosidade e microdureza superficial, bem como análises em MEV da superfície das amostras. O processo a plasma se mostrou satisfatório, sendo capaz de produzir amostras com boa densificação. As medições de microdureza superficial evidenciaram valores semelhantes entre os processos, sendo a amostra sinterizada via plasma a apresentar menor variação de microdureza. Através da análise de EDS das imagens, foi identificada a presença de estearato de zinco em ambos os processos, evidenciado que a extração do lubrificante não foi totalmente eficaz. Ainda, houve uma leve redução da rugosidade no processo a plasma em relação ao convencional.

Aug 17, 2017

By K. N. Karparov

The stress state on two slope profiles overlying an inclined surface with layer inclination of 50 and 150 are investigated. It is demonstrated that the induced stress state in an imbedded weak layer, exposed at the base of the slope, forms a zone of induced tensile vertical and horizontal stresses, which can lead to failure. The zone length depends on the slope angle and the angle of the inclined layers. L’état des contraintes sur deux profils en pente en superposition sur une surface inclinée avec une inclinaison de couche de 5o et 15o est étudié. L’étude présente démontre que l’état induit des contraintes dans une couche faible insérée, exposée au bas de la pente, forme une zone de contraintes de traction induites horizontales et verticales, qui peut amener à la rupture. La longueur de la zone dépend de l’angle de la pente et l’angle des couches inclinées. Die Druckvorkommnisse zweier Hangprofile auf einer schrägen Fläche mit einer Schichtneigung von 5º und 15º wurden untersucht. Es zeigte sich, dass die induzierten Druckvorkommnisse in einer eingebetteten schwachen Schicht, die am Hangfuße offen liegt, einen Gürtel induzierter vertikaler und horizontaler Zugkräfte bildet, die zum Zusammenbruch führen können. Die Gürtellänge ist von der Neigung des Hanges und der Neigung der schrägen Schichten abhängig.

Jan 1, 2003

By M. G. Benz, J. F. Elliott

A. J. Goldak and J. Gordon Parr (U)iuersity of Alberta) —Margolin and Ence's paper reached us only a few days after we had submitted a paper on the structure of Ti2Cu to the AIME. Here, however, we only wish to point out an error in the paper (page 321): "Karlsson has reported the crystal structure of the first intermediate phase occurring in the Ti-rich portion of the Ti-Cu system to be face-centered tetragonal." Karlsson actually reported the structure of Ti3Cu (i.e., "the first intermediate phase") to be primitive tetragonal with four atoms per lattice point: Cu at 0, 0, 0; and Ti at 1/2, 1/2, 0; 0, 1/2, 1/2; and 1/2, 0, 1/2. Thus, Karlsson suggests a primitive lattice with an ordered arrangement of atoms located at corners and face-centers: Ence and Margolin suggest a random body-centered tetragonal structure—-with which our results agree. E. Ence and H. Margolin (authors' reply)— We do not agree that Karlsson has not reported the structure of Ti3Cu as face-centered tetragonal. The fact that Cu atoms are located at the corners and titanium at the face-centers does not indicate that the lattice is not face-centered. We are pleased that the discussers' results agree with our own.

Jan 1, 1962

By H. Margolin, E. Ence

A. J. Goldak and J. Gordon Parr University of Alberta) —Margolin and Ence's paper reached us only a few days after we had submitted a paper on the structure of Ti2Cu to the AIME. Here, however, we only wish to point out an error in the paper (page 321): "Karlsson has reported the crystal structure of the first intermediate phase occurring in the Ti-rich portion of the Ti-Cu system to be face-centered tetragonal." Karlsson actually reported the structure of Ti3Cu (i.e., "the first intermediate phase") to be primitive tetragonal with four atoms per lattice point: Cu at 0, 0, 0; and Ti at 1/2, 1/2, 0; 0, 1/2, 1/2; and 1/2, 0, 1/2. Thus, Karlsson suggests a primitive lattice with an ordered arrangement of atoms located at corners and face-centers: Ence and Margolin suggest a random body-centered tetragonal structure—-with which our results agree. E. Ence and H. Margolin (azlt1zo.l-s' reply)— We do not agree that Karlsson has not reported the structure of Ti3Cu as face-centered tetragonal. The fact that Cu atoms are located at the corners and titanium at the face-centers does not indicate that the lattice is not face-centered. We are pleased that the discussers' results agree with our own.

Jan 1, 1962

Silica-Kaolin Sand Wet Sizing The Bulgarian deposits of silica-kaolin sand are localised in the eastern part of the Danube plain. After wet separation the raw material yields two products - washed kaolin (different grades) and silica sand (different grades). The water washing technology includes: disintegration; spiral classification; hydrocyclone classification and dewatering of kaolin grades; hydroclassification; sizing using drum screens and dewatering of silica sand grades. Research and development program has started to improve the silica-kaolin sand separation in processing plants. Based on the raw material and tails characterisation data and the preliminary experiments using Derrick Stacksizer screening machines a silica-kaolin sand wet sizing technology was developed. The full-scale pilot flowsheet includes the following units: Derrick Stacksizer equipped with 0.43 mm opening Derrick Urethane Panel; 500 mm Flat bottom Hydrocyclone; Derrick Stacksizer equipped with 0.150 mm opening Derrick Urethane Panel; 100 mm Hydrocyclone and Derrick Dual Motor Linear Motion Machine equipped with 0.064 mm opening Derrick Pyramid Panel. The pilot-test data clearly demonstrate that the new silica-kaolin sand wet sizing technology is suitable for Bulgarian silica-kaolin raw material. There are possibilities to increase the silica sand recovery increasing the production of silica sand grade PK 0.16 and starting the production a new grade PK 0.10.

Sep 13, 2010

By John Crusius

? 3-year research program overview ? initial results- MainZone pit Waterline pit ? questions raised ? increasingly common in western N. America ? frequently low-pH waters with elevated concentrations of many metals ? water quality controls poorly understood ? some in U.S. are Superfund sites

May 1, 2002

By Thales Lima Da Silva

As cerâmicas avançadas estão em diversas aplicações técnicas devido à possibilidade de melhoria na tenacidade, ao desgaste e corrosão em altas temperaturas. Neste trabalho avaliou-se o aditivo de sinterização Nb2O5 em teores de 0,2%, 0,4% e 0,6%vol. no compósito 98,5% Al2O3 com dispersão de 1,5% de ZrO2 nanométrica. Os pós foram misturados em moinhos de bola e as amostras foram conformadas por prensagem uniaxial. Utilizou-se a sinterização convencional a 1450ºC, 1500ºC e 1550ºC por 1 hora, caracterizando-se a densidade aparente pelo método de Arquimedes e a microestrutura final por microscopia eletrônica de varredura, procurando-se avaliar o efeito inibidor de crescimento de grão da zircônia frente a possibilidade de formação de fase líquida pela adição de nióbia.

Oct 30, 2017

By Claudio Pereira Diogo

Este trabalho descreve a estampagem a quente seguida de têmpera promovida pela matriz de estampagem. As peças obtidas por esta técnica podem apresentar uma resistência de até 1,6GPa, portanto bem acima das peças equivalentes produzidas através de estampagem a frio ou obtidas com aços conformáveis de alta resistência. O processo permite efetiva redução de peso em importantes componentes estruturais de segurança do automóvel com qualidade dimensional, grande resistência mecânica e à fratura, características essas essenciais a um processo produtivo eficiente e para obter um produto seguro, assim indo ao encontro das necessidades impostas pelo Inovarauto.

Aug 8, 2018

By Derek J. Barratt

This paper compares a number of operating conventional and semi-autogenous grinding circuits and analyzes them in regard to operating and capital costs, specifically as applied to porphyry copper ores.

Jan 1, 1979