Search Documents

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By D. K. ] [Gupta

The Foundations of the Shear keys and alround cut off for Power House -IV of the Western Yamuna Canal Hydroelectric Project at Bhudkalan, Haryana were to be laid at a depth of 26M below the N.S.L and 24.4M below ground water table. The foundation of the drainage sump was to be laid at still higher depth, Viz 29.OM below N.S.L. The Sub soil at the site consisted of Gravel with some amount of sand. The laying of the foundation at such a great depth, at a large depth below the ground water table and that too under such difficult sub-soil conditions encountered a large no of Geotechnical problems-viz excessive seepage, side slope sloughing and sand boiling during excavation. Under the circumstances at the site, the modified foundation construction procedure i.e a battery of M. S. Troughs was placed in flowing water conditions and concreted thereafter, resulting in a sizable cut in dewatering and reducing a significant amount of time and cost of construction affecting a saving of crores of rupees at the state exchequer. Sheet Piling was used to prevent side sloughing in the foundation pit.

Jan 1, 1996

By F Cesnik, P Griffin, S Green

In July 2004 a flotation concentrate regrind circuit was commissioned in the æHigh GradeÆ Ridgeway concentrator at NewcrestÆs Cadia Valley Operations. This was the culmination of two years of project testing, process design and planning which commenced shortly after commissioning the concentrator in March 2002. During the two-year project evolution alternative grinding technologies were evaluated from conventional ball milling through to sand milling. A Detritor mill was eventually selected for the duty and the criteria on which this selection was based will be presented. As the project evolved so too did the equipment sizing with the concentrator quickly exceeding design capacity of 4 Mtpa and currently averaging 5.6 Mtpa, the process design had to accommodate this and future potential throughput increases. This paper will focus on the supporting testwork, circuit surveys and concentrate properties which were used as the design basis for the project. The economic evaluation which led to the project receiving board approval in November 2003 will also be presented. Detailed design and construction management issues will be discussed as will preliminary results and findings up to November 2004.

Jan 1, 2005

By John Nelson

AN OUTLINE survey of the economic outlook for the United States export trade in petroleum products resolves itself broadly into two general divisions; first, a consideration of our present position in this trade, and second, a discussion of the visible factors which promise to affect appreciable changes in the immediate future in that trade. The UNITED STATES PETROLEUM EXPORTS OF MAJOR PETROLEUM PRODUCTS 1925, 1926 and 1927 Gasoline, Naphtha, and Other Light Products 1925 1926 1927* Quantity (gal.) 1,286,787,796 1,784,154,802 1,851,494,190 Value $197,491,588 $263,199,938 $214,721,652 'Illuminating Oil, Kerosene 1925 1926 1927* Quantity (gal.) 885;136,041 924,680,979 827,162,280 Value $84,699,724 $100,352,877 $80,358,082 Gas and Fuel Oil 1925 1926 I 1927 Quantity (gal.) 1,365,358,988 1,449,688,394 1,815,130,464 Value.... ? $49,040,024 $45,354,108. .. $50,343,031 Lubricating. Oil 1925... ....1926 .. 1927 Quantity .(gal.) 402,572,584 388,767,055 403,369,512 Value $90,596,671 $86,414,621 $88,926,815

Jan 1, 1928

By C. J. Newman

In January 1999, a redesign of the Kennecott Flash Converting furnace settler was initiated to enhance furnace integrity and extend furnace life. This furnace uses Kennecott-Outokumpu Flash Converting technology to produce copper directly from copper matte. A detailed assessment was made of all technology available around the world before making a decision on the design features to be incorporated in the new design. The new design includes the following: redesign of all sidewall cooling elements to include the latest cooling element technology; redesign of the furnace hearth to include a stadium hearth at the reaction shaft end of the furnace; redesign of the furnace hearth to include a stepped hearth design adjacent to the furnace sidewalls; addition of flat settler roof cooling elements .around the reaction shaft; replacement of reaction shaft transition elements with an improved design and improvements to the furnace cooling element monitoring systems. The Flash Converting furnace was shut down on a planned basis in July 2001 to implement these improvements after 29 months of operation, converting more than 1,000,000 tonnes of matte. During the 30 day shut down, the improvements were successfully completed, with furnace start up in August 2001

Jan 1, 2002

There are a number of examples of how environmental factors have been integrated into the water management aspects of mining projects. The Kingston Lignite project in South Australia, Pine Creek Gold Mine in the Northern Territory, gravel and sand extraction from the Nepean River flood plain near Penrith, and the Olympic Dam Project have all illustrated that consideration of environmental factors can be integrated with project developments, with beneficial outcomes for both the project and the environment.Each of the above cases demonstrated an individually significant environmental issue, directly related to the interaction between the proposed project and its environment. In each case, careful research and an integrated approach to the problem resulted in a solution that gave both maximum protection to the environment and optimum consideration to the economic feasibility and success of the proposed project.The solutions ranged from alternative mining methods and improved waste and water management through to the ultimate objective of converting a mining project into a major water-based recreation source. These examples have set a precedent that will contribute ignificantly to the successful development of future projects.

Jan 1, 1988

By F. G. Clapp

Introduction.......................................................... 915 Scope of Discussion................................................... 915 Literature and Acknowledgments....................................... 915 Geographic Distribution of Petroleum in South America................. 916 Geographical Comparison with North America.......................... 917 Geological Inferences Regarding South America......................... 918 Quality of South American Oil........................................ 918 South America's Position in the World's Production.................... 919 Political Conditions in South America................................. 920 Peru.................................................................. 920 Distribution of Peruvian Fields................................ :...... 920 Surface Indications.................................................. 923 Geological Conditions................................................ 925 Quality................................................,............ 927 Production......................................................... 929 Argentina............................................................. 932 Distribution of Argentina Fields...................................... 932 Surface Indications.................................................. 933 Geological Conditions............:................................... 935 Quality .......................................................... 936 Production.......................................................:938 Venezuela................................................. 939 Distribution of Venezuela Fields...................................... 939 Surface Indications................................................. 939 Geology of Venezuela Fields.......................................... 941 Quality........................................................... 942 Production.......................................................... 943 Colombia.............................................................. 944 Distribution of Colombia Fields....................................... 944 Surface Indications.................................................. 945 Geological Conditions............................................... 948 Quality............................................................ 950 Production......................................................... 950

Jan 1, 1918

By P. G. Schirk, D. J. Roth

ALTEK has developed a processing system that can receive large pieces of dross & bath, of various metal contents, and reduce and separate these highly metallic concentrates into oxides and non-metallics. This system achieves these results without grinding the metallics into fines. Its unique feature results in the preservation of metallic unit in its largest possible size, which allows for maximum .metal recoveries. The Tumbler, an ALTEK-Didion International joint development, and the ALTEK High Velocity Impacting System (HVIS) are the key elements to this process. This paper will explore the advantage of this cold cleaning system over the direct melting of the raw dross in the reduction of landfill waste. The system also works well for removal of the aluminum from bath from primary smelters.

Jan 1, 2000

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

The following list contains the names of members of whose deaths notices have been received at the Secretary's office during the year 1934 Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns YEAR OF ELECTION - NAME - DATE OF DEATH - ISSUE IN 1934 CONTAINING BIOGRAPHY - PAGE 1885 AMY, ERNEST, J H - Oct 17, 1933 1906 BABB, P A - Sept 17, 1932 1883 BANKS, JOHN H - Oct 3, 1934 ? November - 466 1893 BARNETT, MAURICE - October, 1933 1892 BASSETT, WILLIAM H - July 21, 1934 ? August - 354 September 393 1928 BAUTZ, ROBERT A - Dec 13, 1933 ? January - 74 1927 BAXTER, J C July, 1933 1930 BELL, IRA J 1934 1895 BENNETT, RUSSELL M Oct 31, 1934 December 512 1884 BENTLEY, ROBERT 1928

Jan 1, 1935

The Institute thanks the following for their invaluable assistance, not only in assisting of the planning and organizing for the Vail meeting, but also for their tireless effort in transcribing, editing and processing the various speeches for these proceedings: Elizabeth Sturges-Murray Executive Assistant to the President Western Mining Operations W. R. Grace & Co. Jacklyn Grove Office Supervisor Mining Division W. R. Grace & Co Donna Hollister Further, the Institute announces the appointment of Doris G. Finnie as Secretary-Treasurer. Formerly Office Manager of K&P SALES ENGINEERS, INC., Doris has assisted for the past 15 years in registration for RMCMI. The Institute has opened an office at 777 Nile Street - Suite C Golden, CO 8040 1. Phone her at 3031278-1912 with any changes, corrections or suggestions.

Jan 1, 1982

The 96th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 11th August, 1993. OBITUARIES The President announced the deaths of the following members of the Institute during the past year. Life Fellow E.F. Laschinger. Other Members R.K. Boright, J.S. Jacobi, R.D. Power, J.H. Cannon, C.J. du Plooy, L.B. Mcrae, C.P. Rossouw, A.L. Sillars, A.W. Heugh, R.K. Briggs, P.J. Stark, and C.S. Stott. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1993

By S. -H. Sohn, M. -K. Cho, G. -G. Hong

In order to evaluate the properties of coating materials for BOF, the effects of dolomites (dolomite and light burned dolomite) addition on durability of coating materials were investigated. In all coating materials, matrix was dicalcium ferrite(C2F) and both free MgO and dicalcium silicate(C2S) were precipitated. Fe203 content must be controlled to improve the adhesion and durability of coating materials for BOF during oxygen blowing process. The amount of dolomites added to BOF slag must be controlled in optimum condition with high refractoriness of C2S to improve the adhesion of coating materials for BOF. The weight ratio of converter slag to dolomite must be below 8 to improve the adhesion and durability of coating materials simultaneously.

Jan 1, 2004

We regret to advise that, owing to unusual pressure of business at our printers, Volume TAX will not be ready for distribution so early as was announced in the last Bulletin. It will probably be distributed in November. Volumes LVII and LVIII were mailed during the month of August to all members whose dues were paid on Aug. 1; members who failed to receive their Transactions within a reasonable time are requested to notify the Secretary. In the case of members who have recently changed their addresses, the Transactions Were sent-to addresses on record on Aug. 19; those who did not notify .us of change of address until after Aug. 19 will find their Transactions at the old address.

Jan 10, 1918

By W. Hennig

Efforts to define sustainability indicators are continuing in the mineral extracting industry and sector research institutions. Comprehensive ‘sets’ of economic, ecological and social sustainability indicators for the minerals industry are a necessary precondition for rationale-based negotiations with stakeholders from society. These tools alone, however, will not suffice in a delicately balanced economy-ecology -social well-being equilibrium with ever shifting valuation of different variables. Individual interests and emotions and also ideologically motivated positions of diverse stakeholders are gaining momentum. The minerals industry therefore has to develop beyond the rational pro-arguments for mining in the form of sustainability indicators also proactively its ‘soft skills’ to deal with expectations, fears and outright anti-mining bias, if it wants to retain the ‘social licence’ to continue.

Jan 1, 2005

By Johanna van Deventer, Sean Scott, Rene du Preez, Steven R. Izatt

In order to meet the stringent specifications associated with the production of LME Grade A cobalt cathode, producers need to ensure that a number of impurities, including Cd, are removed from the advance electrolyte to ppb levels (~0.1 mg/L). Conventional options include ion exchange using amino methyl phosphonic acid resin and solvent extraction using D2EHPA. More recently a Cd-selective resin, employing Molecular Recognition Technology (MRT), became available from IBC Technologies, Inc. These three potential unit operations were evaluated in parallel at Mintek. MRT was identified as the most technically feasible option. Results obtained on a cobalt advance electrolyte, containing 55 g/L Co, 6 mg/L Cd and 60 g/L Na2SO4, are presented in this paper.

Jan 1, 2007

By T. H. Miller

THE CHAIRMAN.-This session has to do largely with the question of specifications and conservation as regards secondary metals produced from scrap. We are all familiar with the many varieties of scrap metals and the astonishing number of secondary metals of various specifications produced from the treatment of those scraps. The impact. of the war on this industry has required a great many changes in the types of secondary metals produced from scrap, and in their utilization. In the short period available we cannot cover very much of this field, but we do hope to give you through the various papers a brief introduction to some of the principal problems. Mr. James S. Earle will present the first paper. Mr. Earle:

Jan 1, 1943

By Warren R. P

When the original Mount Gunson joint venture, between CSR and United Uranium ceased operations in December 1971, an intensive ex- ploration campaign was launched to prospect for more ore in the Mount Gunson region. This campaign resulted in the discovery of the Cattle Grid deposit. A comprehensive sampling programme proved the existence of 4.6 million tonnes of ore, at a mean grade of 2.4% Cu, calculated at a 1.0% Cu cut-off. The planning and development programme that followed this discovery included not only the mining and metallurgical aspects of the exploration of the deposit, but also the en- vironmental aspects. Preliminary work included data collection with respect to meteorology, soil types, and existing flora and fauna.

Jan 1, 1976

By Michel Grenier, David A. Young, Brent Rubeli, Mahe Gangal

This work forms part of a study being conducted into the feasibility of constructing a prototype Load Haul Dump (LHD) vehicle for operation in underground Canadian mines. A series of in-laboratory assessments were performed to determine the relative contributions of a Deutz F4L912W (54 HP- conventional vehicle engine) and a Deutz F2L 2011 (31 HP hybrid vehicle engine) to diesel emissions concentration during mine transient duty cycles and steady-state operating modes respectively. Results indicate significant reductions in the quantity of gaseous and particulate emissions with the application of the hybrid system and a high-efficiency ceramic element filter. This paper describes the engine test protocols and the results of this laboratory study.

Jan 1, 2006

By Lane D. P, Malone J. G

The slag fuming furnaces are the major bottleneck in the BHAS zinc production flowsheet. Intensification of the fuming process could significantly reduce this production restriction. Oxygen enrichment was proven to be a means of intensifying the fuming process. This procedure resulted in higher slag bath temperatures, and development work was undertaken towards obtaining accurate slag bath temperature measurement and control. Slag bath temperature measurement techniques were evaluated, with infra red optical pyrometry established as the system with the most potential for continuous temperature measurement and control. Oxygen enrichment resulted in a zinc production capacity increase of 1 000 tonnes per year. An oxygen enrichment technique was developed which both minimized the risk of furnace damage and made the most efficient use of the enrichment oxygen.

Jan 1, 1989