Search Documents

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

The underground storage of LPG and other hydrocarbons is in current commercial use in Northern Hemisphere countries in Europe, Asia and the USA.Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, embarked on a worldwide feasibility investigation in 1989 to establish the viability of constructing an underground LPG storage facility in Sydney, Australia, the first of its kind in the country. Elgas recognised that with the limited 19 000 tonnes of storage capacity at Port Botany and the limitations imposed by use of small coastal ships (up to 10 000 tonnes capacity), a larger storage facility was required to utilise higher capacity ships from more remote sources such as the North West shelf and overseas. This would achieve security of supply in high demand periods and economies of scale. The underground option also provides improvements to safety and environmental standards.

Jan 1, 1999

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By L. H. Monaco

"The evolutional process is always about solving existent problems in order to provide further achievements. But the more something evolves, the more challenges it faces towards greater evolution. Industrial automation systems in Mining have also evolved a lot in the past decades, but they now face new challenges about integration: how to integrate different locations and systems, in a way to reduce costs and increase overall mine efficiency and safety for the operation. This paper compares conventional mining process automation architectures vs. a state-of-the-art, completely integrated system using Electrical Integration based on IEC 61850 standard for Substation Automation Systems. Emphasis is placed on the benefits to manage the entire mining plant as a whole, not only looking at the production rates, but also at the energy consumption for each part of process. In addition, it is discussed how an integrated system approach unlocks safety and productivity gains such as overall process optimizations, improved operator effectiveness, increased plant availability, and reduced maintenance costs. INTRODUCTION The world is constantly changing, and evolution is a natural part of mankind history. The role of evolutional process is to solve existent problems, but usually these solutions create new issues that need to be addressed. This scenario is also applicable to the industrial environment, in which the demand for higher profitability and efficiency on their processes requires solutions with more productivity using less resource. This is not different when it comes to energy consumption: how to optimize production rates and reduce energy costs at the same time? Regarding automation systems, the trend for the industries is to focus on four main challenges: how to provide safety for personnel; how to reduce initial investment for new plants; how to connect remote and in harsh locations; and above all how to deal with the lack of integration between several systems."

Jan 1, 2018

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By John M. Kelly

This report covers the development, exploratory drilling, and production of oil and gas in New Mexico during 1945. The statistical information was gathered from state regulatory agencies and other sources believed to be reliable; it is presented here in combined form for general information only, and the author assumes no responsibility for its accuracy or completeness.

Jan 1, 1946

By John A. Church

Jan 1, 1880

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By Jr. Raleigh

As part vi the development of the Coal Quality Expert (CQRN) --a computer program capable of predicting the impacts of coal quality on power plant performance, costs, and emissions control--several nationally important coals are being characterized to augment the coal quality database associated with the software. The project is sponsored by the U.S. Department of Energy and the Electric Power Research Institute (EPRI) under the Clean coal Technology Program. Since 1989, CQ Inc. (a subsidiary of EPRI) has characterized seven bituminous coals from Alabama, Illinois, Kentucky and Oklahoma and six sub-bituminous coals from the Powder River Basin (PRB) in Montana and Wyoming. Coals from the PRB region--being burned more frequently in Midwestern and southern power plants to reduce emissions of sulfur oxide compounds--can sometimes contain significant concentrations of potentially toxic elements. Although no limits were imposed on air toxics emissions from fossil-fuel fired utilities by the Clean Air Act Amendments of 1990, future regulations may be implemented at the conclusion of Federally-mandated emissions studies. One possible result is that any increased utilization of coals, including those from the PRB, may depend on the potential for removing toxic trace elements prior to combustion.

Jan 1, 1993

By R. L. Bruening, N. E. Izatt, S. R. Izatt

"Rare earth elements (REE) are essential and unique components of many high-technology products without which functioning of modern society would be greatly impaired. Commercial deposits of REE are limited to a few geographical locations. Largely untapped sources of REE are available in endof- life (EOL) magnets, rechargeable batteries, and electronics. Presently, < 1% of REE in EOL wastes is recycled. Conversion of EOL wastes to liquid streams allows use of IBC’s Molecular Recognition Technology (MRT) process to selectively recover, separate, and purify target REE and associated metals at g/L to mg/L or lower concentration levels. The MRT process together with its applications to separations of REE and associated metals in recycling as well as in mining are described. Economic and environmental advantages of MRT are presented. INTRODUCTIONRare earth elements (REE) include the lanthanide series (La-Lu), Y, and Sc. These elements are not rare, but concentrated minable deposits are scarce (Cordier 2012; Haxel, Hedrick, & Orris, 2002). Over 95 % of the world’s supply of REE is controlled by China (Hanson, 2011a) where they are mined, processed, and the pure elements incorporated into a growing number of consumer and military products. The consumer products are marketed worldwide. Since REE are vitally important in consumer and military products, this situation has caused other nations to scramble to develop the capability to produce their own supply (Cordier, 2012).In the U. S., Molycorp has reopened the Mountain Pass REE mine in California and production has begun (Goldenberg, 2010). Development of a reliable internal source of REE is of high national priority in the U.S. (Hanson, 2011b; Hess, 2012: “Obama Announces”, 2012). These elements have in recent decades been incorporated into new consumer and military products that are essential to our economy and defense. These products range from wind turbines, high performance magnets, hybrid car rechargeable batteries, energy efficient lighting electronics, flat screen televisions, and smart phones to advanced weapons systems (Haxel et al., 2002; Levkowitz & Beauchamp-Mustafaga, 2010)."

Jan 1, 2012

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By J. Roger Loebenstein

This report presents a U.S. Bureau of Mines study of the flow of arsenic-containing materials in the United States, based on the best data available in 1991, includes a consideration of arsenic as a byproduct of the processing of nonferrous metals, the fate of arsenic in manufacturing wastes, the quantity of arsenic used in products, tile fate of arsenic in dissipative uses, and the useful life of discarded products. Where possible, estimates are given of the amounts of arsenic lost from the materials flow. Arsenic byproduct of mining nonferrous metals. Historically, most U.S. production has been from the states of Montana, Washington, and Utah. The smelters in these states are believed to be the areas of the country where arsenic is most concentrated in the soil, tailings ponds, and waste dumps. Since the closure of the last domestic producer of arsenic in 1985, all arsenic has been derived from imported sources. Historically, arsenic was important in agricultural applications as an insecticide, herbicide, and cotton desiccant. As the environmental movement gained momentum and the toxicity of arsenic became better understood, most of the agricultural uses for arsenic were banned. Beginning about 1975, the use of arsenic as a wood preservative began to grow. After 1980, wood preservative uses became more important than agricultural applications. By 1990, 70% of the arsenic consumed in the United States was used by the wood preservative industry and 20% by the agricultural industry. The major source of domestic arsenic emissions in 1989 was from the U.S. copper processing indus¬try. About 7,800 mt/yr of arsenic was discarded in leach dumps, tailings, and slag. Another 800 mt/yr was liberated to the atmosphere and 1/100 mt/yr was exported in copper concentrates. On the consumption side, 9,200 mt/yr was lost, mostly from dissipative agricultural uses and the disposal of obsolete arsenical products.

Jan 1, 1994

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transformation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling

Jan 1, 2003

By W. E. Miller, G. S. Scott, G. W. Jones

"INTRODUCTION One of the major activities of the Bureau of Mines is the promotion of safety in mining and the mineral industries. Research is undertaken in connection with these problems to determine the explosion and ignition hazards of combustible gases, liquids, and solids and to investigate means of reducing them.Occasionally the Bureau is asked to determine inflammability or ignition temperatures to enhance safety in nonrnineral industries. From time to time it has complied with such requests when no other agency was available to do the work and the investigation could be conducted with a minimum of time and expense. The present investigation is one of this class.Nicotine (C10H14N2), a colorless combustible liquid having a boiling point of 246°C, is usually obtained from tobacco and its products by extraction processes. When heated to its boiling point it decomposes; the purified product is obtained from tobacco extractions by distillation at reduced pressures or is distilled in a current of inert gas.It has an unpleasant odor, a burning taste, and in the undiluted state is highly toxic. Under certain conditions it can be oxidised to nicotinic acid and in the near future may therefore become of considerable economic importance. Nicotinic acid is a component of the vitamin B complex now commonly used to fortify white flour and other foods that normally are deficient in these vitamins."

May 1, 1942

By P. O. Parfitt

At the McIntyre mine, there are two distinct operations: a gold mine with narrow veins, mined by cut-and-fill methods, and a copper mine with large, open, long-hole stopes. The application of the Critical Path Method to scheduling work in the copper mine, where it has been used successfully for several years, is de-scribed briefly. This application is relatively simple. Use of C.P.M. has now been extended to the gold mine. To replace the former method of scheduling from bar-charts, a procedure was developed for scheduling automatically. To handle an operation of this size and complexity, a computer was essential. Improved schedules are now being produced, with a saving in time.

Jan 1, 1967

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

In the new flowsheet for Inco Limited&apos;s S02, Abatement Project at the Copper Cliff, Ontario operations, a copper/nickel sulphide flotation concentrate will be flash smelted, then converted to Bessemer matte. As in current practice, this will be slow-cooled and separated into components by magnetic separation and flotation. The copper content will emerge as a chalcocite concentrate (impure Cu2S), containing some nickel. This copper sulphide will be converted to copper metal.

Jan 1, 1993