Search Documents

By G. S. Scott, G. W. Jones, F. E. Scott

An important activity of the Bureau of Mines is the promotion of safety in mining and industry . In connection with these activities , the Bureau determines the explosion hazards of combustible gases , liquids , and solids , and investigates means by which explosions may be eliminated or reduced in violence . The limits of inflammability and ignition temperatures of combustible gases , vapors , and solids are of practical importance because such materials can be manufactured , transported , and used with greater safety , provided the range of concentrations and temperatures that cause explosions are known. Acetic anhydride , ( CH3CO) 20 , with which this report is concerned , is a liquid at ordinary temperatures . It is used in the preparation of a number of organic chemicals and in the manufacture of photographic film and of artificial silk . It is perhaps the most important acetylating agent for industrial uses - a property that is especially important at this time because of its direct application in the manufacture of munitions . The sample tested was supplied by the Carbide & Carbon Chemicals Corporation . Its specific gravity was given as 1.083 at 20/20 . The vapor pressures , supplied by the manufacturer , are plotted in figure 1 .

Dec 1, 1943

By R. M. Kakwani

The filtration and dewatering results of -32 mesh Pittsburgh seam coal are discussed with reference to the microscopic structure parameters, i.e., particle segregation in the cake and particle and pore size distributions at different layers. At low solid concentration of 0.33 kg coal/kg water, a non-uniform cake structure is observed in which the particle and pore sizes increase from the top to bottom layers in the filter cake. An increase in the solid concentration in slurry produces more uniform cake structure and higher filtration and dewatering rates. Air bubble entrapment in the coal filter cakes is also discussed.

Jan 1, 1984

By W. A. Yuill

A process has been developed for increasing the grade of chalcopyrite concentrates from about 25 percent copper to about 60 percent copper. The concentrates are treated with two steps of autoclaving and then by flotation. Because of the lower associated weight, copper in the concentrates could be shipped and smelted at less cost than untreated concentrates. Use of the process can also increase overall yield from an orebody if a lower grade concentrate is sent to enrichment than would be sent to a smelter. Potential applications of the process would be for treating concentrates that must be transported a long distance for smelting or for treating concentrates so as to increase the capacity of a smelter.

Jan 1, 1984

By A Vakili

Dilution is associated with considerable direct and indirect costs in underground open stoping operations. As shown in previous works, an improved ability to predict dilution enables the economic risks associated with unplanned dilution to be reduced. Depending on the width of the orebody and depth of mining, the economic performance of an open stoping operation can become even more sensitive to dilution. It is shown in several well-documented studies that as little as 1 per cent of additional dilution can impose millions of dollars of lost profits per annum. Optimisation of a stoping operation is therefore largely dependent on the ability of the operation to minimise dilution. This can only be achieved through sensible analysis of past and future performance of mined stopes using the most appropriate recent available technologies and tools. This article presents a new design process that utilises advanced geotechnical numerical modelling and various other analytical tools to assist with a more robust mine design of open stoping operations. The focus of this design process is on geotechnical factors affecting dilution during the life-of-mine. A recent application of this optimisation method for a mining operation is presented in this paper as a case study. Through the application of this method and various other operational improvements, the mine was able to deliver more consistent production and lower operating costs over its life-ofmine outlook and was able to reduce dilution by up to 50 per cent and achieve sustainable record high production rates.

Mar 29, 2023

By B. J. Moore

This publication contains routine analyses and related source data for 419 natural gas samples from 22 States collected during calendar year 1964 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/ Six previous publications have been made to present the results of 6,293 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1964. The first three, Bulletins 486,5/ 576,6/ and 617,7/ contain analyses and related source data on 5,214 gas samples collected from

Jan 1, 1966

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By W. E. Cassan, W. L. Eaton, James Westfield, W. M. Romisher, Karl Hughes, S. H. Ash

"INTRODUCTION Funds were made available to the Bureau of Mines, United States Department of the Interior, for anthracite investigations during the fiscal year ended June 30, 1945. One of the approved projects was to conduct inquiries and scientific and technologic investigations having a bearing on the anthradite mine-flood problem. The investigative work done from July 1,1944, to June 30, 1946, is described in previous reports (5, 8, 10, 24, 28). 6/Purpose of Report The purpose of this report is to describe the investigative work conucted by the Anthracite Food-Prevention Section, Safety Branch, Bureau of Mines, during the period July 1, 1946, to June 30, 1947,Scope of WorkInvestigative work during the fiscal year ended June 30, 1947, was conducted under the direction of D. Harrington, chief, Health and Safety Division, and S. H. Ash, chief, Safety Branch, Bureau of Mines, Washington, D. C.The broad objective of the investigative work was to obtain factual day on: 1. Anthracite reserves of Pennsylvania.2. Underground water pools.3. Barrier pillars.4. The ""buried valley"" of the Susquehanna River.5. Infiltration of surface water into underground mine workings.The above-mentioned investigations are being continued during the fiscal year July 1, 1947, to Juno 30, 1948.In addition to the investigative work covered in this report, Ash end Eaton presented a paper on barrier pillars, which proposes a method for designing barrier pillars and has been Published by the American Institute of Mining and Metallurgical Engineers (5);"

Apr 1, 1948

By D. Johansson, C. San Miguel, U. Stenman, N. Petropoulos

Blasting is a commonly utilized method in civil engineering projects and mining operations. Ammonium nitrate-based (AN-based) explosives are the most efficient explosives today in terms of handling and performance. However, a side effect is the production of gases. The reduction of these gases plays an important role in the safety and environmental aspects in the working place. Therefore, optimizing the recipes of explosives is vital for minimizing the environmental impact and increasing performance. The aim of the project is to provide results and recommendations on the use of emulsion commercial explosives to support the Swedish mining industry and tunnel-contractors as well as the explosives manufactures. The approach was to test various recipes of civil emulsion explosives to investigate the generation of toxic fumes (CO, CO2, NO, NO2 and NOx) during their detonation. To further increase the knowledge of the influence of different additives, ammonium nitrate prills were added in various percentages. The experimental configuration consisted of magnetite mortar cylindrical specimens with a 50 mm borehole at their center, filled with emulsion explosive. Several tests with different emulsion compositions regarding ammonium nitrate additives (10%, 20%, 25%, 30% and 35%) were carried out in a blasting chamber. The measurement equipment was composed of a flue gas analyzer. The instrument was meticulously cleaned after every test, as well as before and during the tests due to condensation (high humidity and dust) at the inlet of the instrument. The emulsion was manually sensitized with microballons and pumped into the cylinders to ensure lack of bubbles, which could introduce inhomogeneities. The acquired gas concentration data was complemented with temperature, humidity, and VoD measurements. The results showed a linear increase of nitrogen gases as the percentage of ammonium nitrate prills increased. On the other hand, carbon gases had a relatively low coefficient of determination. The VoD data showed a behavior that can be described with a simple quadratic equation.

Jan 1, 2024

By Kenneth M. Maas

The Bureau of Mines inventoried the land availability for mineral exploration and development in northern Alaska and compared this land with known mineral terranes and mineral deposits, to quantify the potential for favorable location of mining claims for metalliferous mineral deposits. This report includes thirty-three 1:500,000-scale maps that depict land availability, and the accompanying text and tables relate availability acreage to areas of favorable mineral terranes. Three categories of land availability and ownership are identified, along with 12 subcategories of land status. Available land comprises approximately 14.5 million acres or 16% of the 90.3-million-acre study area; land available with restrictions accounts for 7.5 million acres or 8%; and unavailable land encompasses 68.3 million acres or 76%. Mineral terranes underlie 37.8 million acres or 42% of the study area; 5.3 million acres or 14% are available for mineral location, 2.8 million acres or 7% are available with restrictions, and 29.7 million acres or 79% are unavailable. There are 500 known mineral deposits or occurrences within the study area. This includes 271 lode deposits, of which 171 lie within a recognized mineral terrane and 55 are on available land. The remaining 229 are placer deposits.

Jan 1, 1987

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindablity index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous of coal as delivered is a check on the practical results obtained in the coal.

Jan 1, 1967

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By L. Patts, J. Rohrbaugh

The Mine Safety and Health Administration (MSHA) has received several reports of filters igniting when high-temperature disposable filters were used on non-cooled diesel exhaust systems in underground coal mines. Based on laboratory testing (to determine the ignition temperature of these filters, which were loaded in the field with diesel particulate matter, or DPM), MSHA determined a maximum safe operating temperature for high-temperature disposable filters. When the results of the laboratory filter ignition testing were reported to the Coal Diesel Partnership (comprised of members of the Coal Industry, Labor, NIOSH and MSHA) the Partnership charged NIOSH with investigating the safe use of high-temperature disposable filters. This paper reports on the design, fabrication and testing of a unique exhaust gas cooling device and the ability of this device to successfully lower filter inlet temperatures and thus reduce the potential for fires.

Jan 1, 2009

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014

By Kyeong Woo Chung, Rina Kim, Ho‑Seok Jeon, Yeongjin Ahn, Byunghun Go, Min‑seuk Kim, Hong‑In Kim, Sujeong Lee, Yuik Eom

The study focused on the recovery of vanadium from a Korean vanadium-bearing titaniferous magnetite (VTM) ore, examining the behaviors of magnetic separation and Na2CO3 roasting-water leaching. Two concentrates were prepared using single-stage dry magnetic separation and three-step wet magnetic separation, resulting in V2O5 grades of 0.8% and 1.0% and major gangue mineral SiO2 contents of 6.5% and 1.7%, respectively. These concentrates were subsequently roasted at 1050 °C with the addition of Na2CO3 and then water-leached at 25 °C. Various stoichiometric ratios of V2O5 to Na2CO3 were tested, ranging from 1:1 to 1:40 of the theoretically required amount. As the amount of Na2CO3 increased, the vanadium leaching efficiency showed fluctuations between 4 and 35% for ratios of 1:1 to 1:10, while it linearly increased from 4 to 82% for ratios of 1:10 to 1:40 in the leaching of the low-grade concentrate. In contrast, the leaching efficiency increased from 47 to 74% for ratios of 1:1 to 1:8 and then sharply rose to 84% at a ratio of 1:10 in the leaching of the high-grade concentrate. Subsequently, it reached a plateau of 92 to 94% for ratios of 1:20 to 1:40. The difference in leaching efficiency was primarily due to the reaction of gangue minerals with Na2CO3, which hindered vanadium leaching from the VTM concentrates. This hindrance was notably more pronounced in the low-grade concentrate with the lower salt ratio, as the gangue minerals exhibited a preference for consuming Na2CO3 over vanadium. The mineral formation was analyzed in detail using XRD and MLA to shed light on the mechanism of different vanadium leaching behavior depending on the concentrate grade and vanadium to salt ratio. Based on the results of this study, it is evident that applying a proper magnetic separation procedure is significant to achieving satisfactory vanadium recovery with less salt amount by removing gangue minerals ahead.

Mar 15, 2024

By C. I. Pierce

The Bureau of Mines used an electrolytic tank model to investigate the response of guard electrodes of different dimensions under different simulated reservoir conditions. Sandstone disks from the Berea and Connellsville Formations were used as resistive beds in the model, and agar gel or water was used as conductive beds. In the experiments, bed thickness, hole diameter, mud resistivity, and bed resistivity were varied. The guard electrode is an excellent tool for determining true bed resistivity in the thin-bedded oil reservoirs of the Appalachian area. Vertical resolution and resistivity values are good when there is little or no invasion. Resistivity values are near true bed resistivity in beds thicker than about six hole diameters when the electrode-to-hole-diameter ratio is close to 1. However, low-resistivity muds cause false peaks to appear on the logs near bed boundaries in thick beds, and for resistive beds having a thickness approximately three to five times the hole diameter, apparent resistivities tend to be excessively high when mud resistivity is low.

Jan 1, 1966

By Robert B. Coleman

The recent surge in demand for uranium in the US, accompanied by a significant increase in price, has stimulated the search for and development of lower grade ore bodies. At the mill, this translates into much larger throughputs and-compounded by many recently enacted environmental considerations-has made the cost of milling a critical factor in today's uranium production economics. The three conventional milling methods employed in the extraction of uranium ores are reviewed in the following sections.

Jan 10, 1978

By Walter L. Maxson, Fred C. Bond

SINCE the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. STANDARD BALL-MILL GRINDABILITY TESTS The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill in all tests is 700 c.c. of the packed minus 6-mesh roll product, and the number of grams occupying 700 c.c. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter. Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I ½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity to be expected from a given mill is calculated by comparing the

Jan 1, 1943

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, PSo, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of O2 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003