Search Documents

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

By J. R. D. Gravel, D. A. Poland

"The induration of iron ore pellets has always utilized prefired pellets to protect the pallet cars from the environment of the induration furnace. This paper presents the process used to obtain superior upper sidewalls. These heat resistant castings are used on induration pallet cars, and their life improvements by as much as 400% is a significant step towards the reduction of the prefired (or hearth layer pellets.) The benefit to the industry in the removal of the hearth layer is improved overall productivity. IntroductionThe Iron Ore Company of Canada (IOC) operates with production facilities located in Labrador City, Newfoundland and Sept Iles, Quebec. It has recently been acquired by North Limited, an Australian based resource oriented company. Prior to its acquisition, IOC has examined several methods of operational cost reductions. One of these was an examination of indurrating pallets. Pallets are composed of numerous assemblies and sub-assemblies. The examination of the upper sidewalls began as an intent to increase the operational life of the component. The anticipated net effect was to be a reduction in the overall pallet maintenance cost. All of the components and assemblies have undergone a severe scrutiny. IOC has found that the success of the project has depended upon not only the technical competency of all parties involved, but also upon the ability to share risk, to be innovative, and to find a partner with whom the development can proceed without fear and yet with accountability. IOC has found in Cast Steel Products (CSP) such a partner in the field of pallet development. This paper will undertake to explore the progression into the arena of partnering between IOC and CSP. CSP and IOC met in the fall of 1994. The work of re-engineering the pallets began with an initial order for 36 pallets in March, 1995. The work on the upper sidewalls involved segregation of the effect of alloy development versus physical geometry development. The nature of partnering between the two companies allocated alloy development to IOC and physical geometry development to CSP, yet no advancements were made in either area without the close co-operation or the involvement of both partners."

Jan 1, 1999

By A. Warczok

The computer simulator of slag cleaning in an electric furnace is based on a set of mathematical models describing heat liberation, the rate of slag reduction and gravitational coalescence of matte and metallic copper inclusions. The simulator consists of a mass and heat balances as a frame, in which the kinetic equations of the slag reduction and phase separation are incorporated. Friendly user-screen interface allows for dynamic control of process parameters in real time together with simulation of typical operations, such as furnace charging with liquid slag, solid reverts and coke, tapping out of the slag and matte, motion of electrodes and control of the transformer. The batch, semi-continuous or continuous process can be simulated. The process parameters are displayed and continuously recorded for further analysis. The computer simulator is a powerful tool for process optimization, training of furnace operators and the design of new slag cleaning installations.

Jan 1, 2007

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003

By H. Akbari

Ordinary portland cement (OPC) is the key pozzalonic component of the concrete mix widely used as a construction material worldwide. B illions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of C O2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic C O2 emissions each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon footprint of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the nonmetallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned extracting some of the valuable metal oxides from fly ash prior to using the major nonmetallic portion of the fly ash for geopolymer concrete application. The results obtained from this study showed that the compressive strength of geopolymer concrete compares favorably with that of conventional concrete prepared using OPC.

Dec 1, 2013

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961

By Alan M. Bateman

Before World War II we proudly considered that we were the nation of all the world most richly endowed in mineral resources. We knew it was no accident that those countries abundantly supplied with mineral resources became the great manufacturing nations, and the politically and militarily strong ones; and that our own great industrial cities sprang up where coal and iron met. We all reallized, especially we of the mining profession, that the energy of fuels and the solidity of metals spelled industrial growth and in turn industrial might and that other nations came to regard mineral self-sufficiency as one of the chief goalsof economic nationalism.

Jan 1, 1949

By Wilton Johnson

Native asphalt was produced in 1982 by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries, Inc., Uvalde County, Tex. Historically, gilsonite, a solidified hydrocarbon found only in Utah and Colorado, had been mined by American Gilsonite Co. and by Ziegler Chemical and Mineral Corp. from properties near Bonanza, Uintah County, Utah. During 1982, Hydrocarbon Mining Co., a subsidiary of the Oberon Oil Co., entered into a joint venture with Miocene Resources Inc. of Novato, Calif, to form Hydrocarbon Resources Co. for the purpose of mining gilsonite about 50 miles south of Vernal, Uintah County, Utah. Under the agreement, Hydrocarbon Mining contributed gilsonite-bearing properties held by lease or sublease as well as mining equipment to the venture. The property contained leases totaling 760 acres with probable reserves of 268,000 tons of gilsonite. Miocene Resources provided the partnership with a minimum of $200,000 to develop two of the leases and were to be responsible for management of the mining operations.2

Jan 1, 1983

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Wolfgang Guetter, Wolfgang Weber

The upgrading project for two hydropower plants in Slovenia, Europe, requires two new pressure tunnels: Plave II (5.9 km Flysch) and Doblar II (3.6 km Limestone). It is the worldwide largest application of the Double-Shield TBM technology combined with an extremely thin-walled monoshell honeycomb lining system. The first drive has been completed by end of June 2000 achieving best performances of 50m/d and almost 1,100m/mth. In September 2000 the TBM started the second tunnel without any required adjustments due to geological or other reasons. Another 52m/d have been bored already within one production day of two 8 h shifts achieving a maximum penetration rate of more than 6m/h. The completion of the Doblar drive can be expected by February 2001.

Jan 1, 2001

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By Manuel Gomez

Published experimental coke data from a pilot plant slot-type oven were examined by statistical regression analysis. Quantitative relationships were found to exist between the coking rate, bulk density, and fine grinding of the coal, sole-oven expansion, volatile matter, moisture, ash, and carbon con-tent of the coal and coke parameters indicative of size and strength. Regression equations developed from coke data were shown to yield computed values that were in good agreement with experimental results for 11 coke properties. Prediction equations developed were evaluated with an independent set of data. Present results indicate that the variables cited undergo much interaction and the sum of these interactions determines coke size and strength.

Jan 1, 1967

By P. R. Taylor

Laboratory experiments have been performed to evaluate the kinetics of roasting pyrite and arsenopyrite in air at elevated temperatures, in the presence of lime. The effects of temperature, time, air flow rate, particle size, lime type, and mineral/lime weight ratio on the rates of oxidation, lime sulfation, and lime arsenation were studied. The reaction products were identified using chemical analysis, x-ray diffraction, SEM analysis, and optical microscopy. The results are discussed in terms of the utilization of lime to capture sulfur and arsenic during the roasting of refractory precious metal concentrates. More than 99.9% of the arsenic and 98% of the sulfur are contained when roasting pyrite and arsenopyrite with hydrated lime under typical roasting conditions.

Jan 1, 1991

By J. B. Lott

The authors' company has recently undertaken a development programme aimed at exploring the relationships between the variables of greatest importance in the design of mixer-settlers for metallurgical solvent extraction applications. Such applications vary from relatively small scale plants treating copper mine waters, nickel containing effluents, etc., where the total flowrates may be of the order of a few hundreds of gallons per minute, to very large scale plants treating several thousands of gallons per minute of leach liquors containing copper, uranium or other metals. This paper outlines the physical and mechanical factors which must be taken into account when designing mixer-settler systems for large scam. solvent extraction plants. The performance of the equipment will also be dependent upon the chemistry of the system, including the kinetics and thermodynamics of the ion exchange reaction itself, the effect of impurities flocculants, surfactants, temperature, etc., but these will not be dealt with here. Much of the laboratory work has been carried out using copper containing solutions and either LIX 64* or LIX 64N* as the solvent dissolved in various grades of kerosene. For simplicity, all the graphs and tables of results which are presented and discussed here will refer to the LIX-copper system, although the conclusions will in many cases be generally applicable to other systems also. The LIX-copper process is now sufficiently well known to obviate the need for a full description, however, an outline flowsheet of the process is shown in Figure 1. The ultimate objective of a laboratory programme for a particular extraction application is to provide data upon which a mixer-settler system can be designed to handle a given throughput of leach liquor and extract from this liquor the maximum quantity of metal for the minimum cost. In other words, the objective is to determine the design and operating parameters which achieve the optimum balance between capital and operating costs. * Trade-marks for General Mills solvents.

Jan 1, 1971

By P. van der Steen

This paper examines the historical developments in diamond beneficiation technology and the impacts on the industry. The art of diamond beneficiation has given way to the application of scientific process, but at considerable capital expenditure. The shift in beneficiation methodologies has been disruptive to the traditional skills set of the industry, but evolutionary change continues and has been beneficial to the quality of the final product.

Jan 1, 2010

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By Ingvar Ymén, Anders Sandc, Jan Rosenkranzc, Lisa Malma, Ann-Sofi Kindstedt Danielssonb

The understanding of particle surface properties is essential for the study and evaluation of froth flotation phenomena, particularly in the investigation of various chemical or reagent effects. Dynamic Vapor Sorption (DVS) is a method used for the analysis of surface properties of powders for instance in the pharmaceutical industry. To the knowledge of the authors, it has however not been used before in applications related to mineral processing. The DVS technique involves measurement of the water uptake of a relatively small amount of sample as a function of the relative humidity (% RH) in a temperature-controlled environment. The purpose of this work was to evaluate the method and investigate how it can complement existing techniques for surface characterization in mineral processing. Four samples (feed, CuPb concentrate, Cu concentrate and Pb concentrate) from the Cu – Pb flotation process in the Garpenberg concentrator, Sweden, were analyzed by DVS and the traditional capillary absorption technique (Washburn capillary rise). This enabled comparison between the two methods and evaluation of their respective advantages and disadvantages. Both methods give the expected ranking of the hydrophobicity for CuPb concentrate, Cu concentrate and Pb concentrate, but a discrepancy was observed for the feed. Washburn gave a value for the contact angle which was in the same range as for the CuPb concentrate, whereas DVS gave a value for the moisture uptake which was much higher than for the CuPb concentrate. Thus, DVS ranks all samples correctly, but with an unexpectedly high value for the feed whereas Washburn gives good ranking for three samples out of four. Potential reasons for the discrepancies are discussed.

Jan 1, 2018