Search Documents

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By Richard A. McIvor

"All mine shaft conveyances in Canada and most of the United States that are supported by a single hoist rope or attachment point and used for transporting persons are required by regulation to be equipped with safety catches and mechanisms. These safety mechanisms, commonly called safety dogs, are designed to stop and hold a free falling conveyance, with a full personnel load, in the event of a hoist rope or attachment component failure. The conveyance’s safety mechanism must be tested under dynamic conditions before it is used to transport personnel. This paper will discuss free-fall testing and it’s results on conveyance free-fall tests performed in the test tower at INCO Limited, Sudbury, Ontario.Topics covered will be free-fall tests on various wood types such as B.C. fir, Karri wood and Trusjoist MacMillan Limited Parallamwood (PSL), comparison of deceleration rates versus free-fall velocity and the influence of safety dog tooth design on deceleration rates."

Jan 1, 1996

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014

By Peter F. Pullen

The need to apply the latest available technology to develop better tools and methods to meet problems in the mining industry was recognized by six of Canada's leading mining companies. As a result, MIROC (Mining Industry Research Organization of Canada) was chartered to identify problem areas in Canadian mining and to have research carried out to develop the tools and equipment to meet these perceived needs. The initial activity of MIROC has been in the environmental field, with improved clothing and protective devices being developed by contractors. Work clothing for miners is now being field tested. Respiratory protection and a new personal light source combined in a new "space-age" helmet are about to be issued for testing. Further developmental work is being carried on to offer these units and probably other personal protective devices on an individual basis as well as in a combined package.

Jan 1, 1979

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By Y. P. Wu

Steeply dipping seam refers to the coal seam with dipping angle in the range of 35?55°, which is well recognized to be very hard to mine by the mining industry all the world. In the last two decades, some fundamental researches were focused on the strata behavior of long-wall panel, complicated rock mass breaking process of the steeply dipping seam, overburden stress field developing and evolution, rock strata breaking and moving process, rock structure stability mechanism and control. Results show that it?s presenting macro stress arch-shell (MSAS) of the stress distribution of the overlying rock in steeply dipping seam. The MSAS is the spatial distribution of intensity envelope line under the strength criterion and has the geometry shape asymmetry as well as the stress distribution heterogeneity. The arch- shell base will forward as the working face mine forward and the shell roof will extend to higher overlying strata above the gob. In this paper, the stress arch-shell analysis model and coordinate system were established and analyzed the inclined masonry structure at different zone. Analysis results show that the rock damage at the key part of the arch-shell is the main factor which causes whole overlying rock structure failure. The rock structure instability modes have tension instability of the shell roof, compression-shear instability of the shell shoulder and composite instability of the shell base, meantime, instability coefficient is proposed to determine instability condition. The above research results enrich the complex coal seams mining theory and provide a theoretical basis for mining safely and efficiently in steeply dipping seam.

Aug 1, 2013

By W. M. Williams

"Although manganese is a metal virtually unknown to the layman, it is hardly necessary to point out to the engineer the importance of manganese in modern metallurgy, an importance intimately linked with iron (and steel), the basic materials of engineering construction for hundreds of years and certain to remain so for long into the future. World steel production will approach and perhaps reach 1 billion tons/year in the 1980s; with a manganese content between 0.5% and 1 % in ordinary steels, and more in specialty steels, manganese use worldwide will soon approach 15 million tons annually. Manganese was discovered and isolated in Sweden in 1774 by Karl Wilhelm Scheele (who also discovered molybdenum), but the element was only of scientific interest for several decades. By the early part of the nineteenth century, however, manganese oxide had become commercially available and was in use for colouring glass and for the production of chlorine. Commercial application in metallurgy appears to have been limited to the manufacture of crucible (or ""cast"") steel, a highquality product made by carburizing wrought iron, and melting it in small batches to make ingots which could be rolled and used for special applications, e.g. for the manufacture of fine tools or for ""steeling"" the cutting edges of implements such as wrought iron axes and chisels.* However, it was not until Bessemer's epoch-making invention of cheap steel in 1856, and the dramatic expansion of the steel industry thereafter, that manganese assumed the importance that it holds in modern steelmaking."

Jan 1, 1999

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By T. Matthews

"One critical factor in mineral reserves reporting, as well as mine-reserves reconciliation, is the impact of dilution and ore loss in the mining process. This paper considers the implications of various factors on dilution and ore loss projections, by orebody geometry, mining method, and ore control systems. We also discuss the implications of resource estimation methodology on dilution for reserves. DEFINITIONS Dilution and ore loss are two critical concepts in mining, which address the differences encountered between modeled grade and tonnages and actual production. Dilution is volume increase and grade reduction caused by multiple factors, chief among which are mining of waste material along ore-waste contacts, mining of internal waste as ore, and misclassification of waste as ore in the ore control process. There are also geostatistical and estimation aspects sometimes lumped with dilution, including the volume-variance effect (the tendency for small volumes of material to include a less regular distribution of grade than large volumes of material). Ore loss is described as reductions of ore volumes in the mining process due to misclassification of ore as waste in the ore control process, exclusion of discontinuous mineralization from mining due to geometry or continuity, and mechanical losses in the mining process. Dilution is typically taken as an increase in tonnes of ore with no change in contained metal (and thus results in a reduction in grade.) (Some workers consider the likely grade of the diluting material as well, particularly in deposits with gradational grade boundaries—this will be addressed later in the text.) Ore loss is typically taken as a reduction in tonnes at average grade of the ore, and thus results in a reduction in both tonnes and contained metal. If model (resource) tonnes are Mt, grade is Mg, and contained metal is Mm, the resource with ore loss (L) and dilution (D) included (Rt, Rg, and Rm) will be:"

Jan 1, 2015

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By RALPH HAYES SWEETSER

IRON ore and bituminous coal are the two basic raw materials for the whole iron and steel industry. The ore furnishes the iron and is absolutely necessary-all iron and steel products come directly or in- directly from the iron ores. The bituminous coal furnishes the carbon needed for the smelting of the ores and for the fuel used in all the processes of iron and steel manufacture. The necessary carbon could be furnished in some other form besides bituminous coal. In fact, it is only since the Civil War that bituminous coal has been the chief source of the carbon for metallurgical fuel. For many years only charcoal made from the forests furnished the carbon for smelting iron ores. About 90 years ago, anthracite coal was first used as blast-furnace fuel and for many years continued to be the chief blast furnace and steel making source for carbon. Even in my own blast-furnace experience, I have used charcoal in Canada and anthracite in Pennsylvania for smelting ores in an iron blast furnace. Bituminous coal, now almost exclusively the source for the carbon used in smelting iron ores, also furnishes most of the heat used in the steel-making processes. It is seldom used in blast furnaces in its natural condition, hut is first coked in beehive, or in by-product coke ovens; such bituminous coal is called "coking coal." Bituminous coal that is suitable for making the producer gas used in the open-hearth steel process is called gas coal. Any bituminous coals suitable for making blast-furnace coke or foundry coke, or that can be satisfactorily used for making producer gas, are classed as metallurgical coals and as such are to be considered in my proposed plan for the evaluation of metallurgical coals. According to Bureau of Mines Bulletin No. 449 these coals comprised 22 per cent of the bituminous coals mined in this country in 1923.

Jan 1, 1926

By W. M. Ross

AMONG the comparatively few A radical changes in mining equipment in recent years is the introduction and use to an ever greater degree of detachable bits for rock drills. Just how great the possible field for economic application of this innovation is, and to what ex- tent detachable bits are used instead of the conventional type of drill steel, are matters of conjecture. Just as a rough approximation, one might conceive that at least three-quarters of the drilling done in mines today could better be performed by steel with detachable bits, instead of only about one-quarter as at present.

Jan 1, 1939

By Robert H. Peters

Are the safety rules in your work place effective? Do supervisors enforce them as they should? Do supervisors abide by these rules? Safety rules are an important aspect of many company safety programs, particularly if employees must work in an intrinsically hazardous environment such as a coal mine. However, for various reasons, supervisors sometimes fail to enforce safety rules (Arvey & Jones, 1985; Hartshorn, 1998). This paper presents some findings obtained from interviews with coal miners about why supervisors sometimes fail to enforce an important mine safety rule. It also contains a few suggestions addressing what could be done to help supervisors perform this job function more effectively.

This paper sets out to consider a specific type of corrosion protection system, which is referred to as a Duplex Coating system. The dictionary describes a duplex system as consisting of two elements or a “twofold” composition. The duplex system described in this presentation is such a two-part corrosion protection coating, viz, hot dip galvanizing as the firm base or primer, followed by a top paint system designed to combat severe corrosive environmental conditions encountered in nature. In principle, the duplex system is a cost effective and balanced, designed coating that is suited to the environmental conditions and service life requirements.

Jan 1, 2009

By A. N. Clay, N. N. Moeketsi, S. Joubert

For many years, mine-impacted water has been regarded as a problem and linked to long-term environmental liabilities. However, this water can be a renewable and a sustainable resource, provided that it is managed in a responsible and sensible manner. South Africa’s National Water Resource Strategy (NWRS, 2013) considers water that can be used to contribute to economic activity to be a water resource. Although all water resources are considered as belonging to the State, government does not appear to have meaningfully explored the use of mineimpacted water to contribute to the country’s economic activity. Africa is blessed with more sunshine than anywhere else, apart from Australia, yet we see no rollout of vast quantities of solar panels to ensure every African family has access to affordable power. This suggests that governments are incapable of managing such a free resource. At the same time, apart from the equatorial areas, water is a seriously constrained resource and yet we expect the same entities to manage a commodity none of us can live without. This paper explores the conversion of mine-impacted water from waste to a resource and how the inclusion of other stakeholders (such as water users, landowners, and ordinary South Africans) could benefit the process.

Jan 2, 2022

By Cui Wang, Qian Li, Kexin Jiao, Haibin Zuo, Jianliang Zhang

Abstract：A rational cooling water system is the assurance for long campaign life of blast furnace．In the paper, the heat transfer of different furnace period and different furnace condition based on the water quality characteristics were analysed, and the reason of the heat flux over the normal from the hydrodynamics was analysed. The results showed that, the vapour-film and scale existence significantly influenced the hearth heat transfer, which accelerated the brick lining erosion. The water dynamic characteristics of the parallel inner pipe or among the pipes were the main reason for the abnormal heat flux and film boiling. As to the reasonable cooling water flow, the gas film and the scale should be controlled and the energy saving should be considered.

Jan 1, 2015

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By S. J. Jung

In recent years, the use of shotcrete, a practice familiar to the mining industry, has been on the increase. This research has come about because of the recognized need for a safe, easy way to line small diameter bored raises (less then 150cm). Up until now, an operator has gone down the raise and applied the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1994