Search Documents

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

This report briefly describes the broad program of research and technologic work conducted by the Bureau of Mines on coal and related subjects during 1966. In addition to n description of investigations on mining, preparation, and utilization of coal, an account is given of the Bureau's work in mine health and safety, coal resources, mine explosives, and environmental conditions relating to coal mining and utilization. Details of most of the projects are reported in publications cited throughout this report. Centers and laboratories conducting the coal research and related investigations appear in appendix A; organizations, institutions , and companies contributing to the Bureau's coal research and technologic program are listed in appendix B.

Jan 1, 1967

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By Yongjun Peng, Yufan Mu, Rolf A. Lauten

"Chalcopyrite, a major source of copper, is commonly found associated with iron sulfides, particularly pyrite. The separation of chalcopyrite and pyrite by flotation is difficult due to the galvanic interactions between pyrite and chalcopyrite during grinding and flotation. Galvanic interactions may cause oxidation and dissolution of chalcopyrite, copper activation of pyrite and the formation of hydrophilic iron hydroxide coating. The overall effect may change the floatability of the components and lead to the misplacement of pyrite into chalcopyrite concentrate. The objective of this study was to investigate the effect of lignosulfonate-based biopolymers on the depression of pyrite in the flotation of chalcopyrite with xanthate as collector and the mechanism responsible for the selective depression of pyrite. The flotation results showed that biopolymers depressed the flotation of both copper-activated pyrite and chalcopyrite in single mineral flotation although to different extents. In the flotation of mixed mineral systems, biopolymers significantly depressed pyrite flotation but had a less influence on chalcopyrite flotation. The selective depression of pyrite by biopolymers was due to the preferential adsorption of biopolymers on copper-activated pyrite surface. Galvanic interactions between pyrite and chalcopyrite surfaces promoted copper activation on pyrite. Presence of cuprous ions on pyrite surface favored biopolymer adsorption by the formation of a complex between the cuprous ions and biopolymer molecules. The same galvanic interactions also facilitated chalcopyrite oxidation leading to the formation of hydrophobic polysulfide that enhanced the hydrophobicity on chalcopyrite surface. The biopolymer structure controlled the depression effect. The results showed that the biodegradable biopolymers are promising depressants for pyrite.INTRODUCTIONCopper sulfide minerals, such as chalcopyrite (CuFeS2), bornite (Cu5FeS4), chalcocite (Cu2S) and covellite (CuS), are the major mineral source for copper. They are often found finely interlocked with iron sulfides, especially pyrite (FeS2) (Owusu, Brito e Abreu, Skinner, Addai-Mensah, & Zanin, 2014). Pyrite, as the most abundant sulfide mineral, is perceived as gangue in most cases and should be removed from the associated sulfides to minimize its contamination of the copper concentrate (Owusu, Addai-Mensah, Fornasiero, & Zanin, 2013; Wang & Forssberg, 1991). The commonly used strategy to remove pyrite is flotation (Wang & Forssberg, 1991)."

Jan 1, 2016

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By A Trench, S Ulrich, S Hagemann

A synthesis of reported All-In Sustaining Costs (AISC) for 57 Australian gold mines in the period 2014–2016 reveals for the first time the clear influence of grade upon cost performance, most evident in gold-only underground mines. Past syntheses of costs on a single quarter basis have viewed grade as potentially subordinate to other factors such as production scale, mine geometry, mineralisation style and a combination of other mining-related costs. Better understanding of the grade to cost relationship on both an individual mine and whole-of-portfolio portfolio basis is needed. Insight into the roles and trade-offs between other cost-determining factors will aid the future sustainability of the gold mining sector in Australia and assist in targeting prospects for future resource growth and development. While the overall trend is toward higher-grade mines displaying lower costs and vice versa, the grade to cost functions appear radically different between mines based on time-series data. The median cost of Australian gold production in the final quarter of 2016 was A$1081/oz. The threshold for lowest cost quartile production was A$965/oz. Underground production now dominates Australian gold output – with 71 per cent of ounces originating from operations that are either entirely underground or hybrid pit/underground mines. Scale economies are evident, with smaller mines predominately among the higher cost producers. For mines of equal grade, open pit mines are lower cost than underground operations. Reserves are modest, with a median mine life for underground operations of 4.7 years based on current production rates. Reserve additions at mines are likely constrained not only by the finite nature of mineralisation at each mine but also by the geometrical difficulty of accessing suitable drilling locations to test for reserve extensions.CITATION:Ulrich, S, Trench, A and Hagemann, S, 2017. Towards an understanding of production costs at Australia’s underground gold mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By Alexander N. Winchell

"Location. The iron formation of the Gogebic district (including the Penokee) comprises a narrow belt south of the western part of Lake Superior extending from Michigan for a considerable distance into Wisconsin. From the mouth of the Montreal River (about twenty-five miles west of Ashland) the iron formation is only about twelve miles distant, but it is about twenty miles south of Ashland. Beginning on the east at a point about eight miles east of Wakefield, Mich., it extends through Sunday Lake, Bessemer and Ironwood in Michigan, and thence south of west through Hurley, Wis., and only a short distance south of Mellen, Wis. About eight miles westward from Mellen, the formation disappears, but six miles further west it is known to reappear and continue thence for about eight miles. The total length of the range is about sixty miles, two-thirds of this distance being in the State of Wisconsin; but nearly all of the ore has been obtained from the eastern third of the district, which is in the State of Michigan.History. This iron range was first noted in 1848 by Dr. Randall, assistant geologist to Dr. David Dale Owen, while following the fourth principal meridian northward. It was also reported by Charles Whittlesey in an account of a survey made in 1849, and published by Owen in 1852. Analyses of the iron ore are given with the following account. ""The bed of magnetic iron ore south of Lac des Anglais is of extraordinary thickness,25 to 60 feet. * * In the wild and deep ravines where the Bad River breaks through the range, there is a cliff of slaty ore * * * probably three hundred feet thick. * * * I estimate more than one-half of this face to be ore, and in places the beds are from ten to twelve feet in thickness, with very little inter-mixture of quartz * * * . The position of the best exposures of ore which I saw is such as to require from eighteen to twenty eight miles of transportation to reach the lake."""

Jan 1, 1920

Jan 1, 1882

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By David J. McDougall

"The production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with Les Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivieres (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about Les Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian milieu, but whatever the reason, the other Quebec iron works have been generally ignored. All but one of the Quebec blast furnaces could be described as ""pre-industrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day. Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence River. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces. Five of these, including Les Forges du St. Maurice, were located on or near the St. Maurice River which enters the St. Lawrence River from the north, and two, the St. Francis Forges and the Grantham Iron works were on or near the St. Francis River which enters the St. Lawrence from the south. In a general way deposits of bog iron ore in the St. Lawrence lowlands of Quebec were contained within the limits of the post-glacial Champlain Sea, with many clustered along the flanks of the St. Narcisse recessional moraine which is crossed by the St. Maurice and other near-by streams, and the Drummondville recessional moraine which is crossed by the St. Francis River."

Jan 1, 1999

By R. MacRosty, R. Pula, P. Gebski, W. Braun

"This paper provides a progress update on three tapblock monitoring technologies that Hatch has been developing with our clients for non-ferrous smelting furnaces.The Tapblock Diagnostic System (TDS) is an advanced on-line monitoring system that uses temperature data along with embedded thermal model results to evaluate the condition of a tapblock over its campaign life. Hatch recently installed a second Tapblock Diagnostic System, some details of which are provided in this paper.The Tap-hole Acoustic Monitoring (TAM) system is installed on water-cooled copper tapblocks and uses the noise from the tapping channel to provide a qualitative indication of wear and deterioration of the tapping channel refractory. In addition, TAM can be used to monitor drilling and lancing performance, and potentially could also be used in the future as a guide for automatic drilling and lancing systems (Sadri et al., 2008).The third technology is the use of fibre optic sensors to measure temperature on the hot face and in the tapping channel of a tapblock. Fibre optic technology allows installation of numerous sensors in key locations where they are very sensitive to tapblock condition and also provide more extensive spatial coverage than is possible with traditional instruments. This paper provides an update on our efforts to address issues with premature failure of the sensor cables due to corrosion, and also converting the vast amount of data from the sensor cable into information that can be used by furnace operators."

Jan 1, 2014

By Dale C. H. Nevison

One of the most intensive of material rivalries is the confrontation between zinc die castings and plastic injection moldings. Pressed hard by the plastics industry, zinc die casters are learning how to make parts with less material yet without sacrificing quality. The key to this new trend is the technique of Thin Wall die casting. The obvious benefits of Thin Wall are lighter weight and lower cost. Again, obviously, these are the very selling points that put plastics into many appliance and automotive parts formerly made of zinc. One of the factors that has been most conducive to the outstanding growth of plastics has been the increasingly prevalent concept that "adequate" properties are sufficient, especially if there are cost advantages. Most of modern design today is oriented around the reasonable life of a product, rather than indefinitely extended life. This is simply an acknowledgment of the existence of a design environment that pervades many areas, reflecting the life-cyclic desire for change. Too often, so-called "weight-saving" materials end up being very costly - not only in production, but in durability and dependability. Change for the sake of change usually doesn't effect a change for the better. In the majority of cases, the best bet is to design in traditional materials and minimize the material needed, while maximizing the efficiency of the production process. Component prices of products to be produced from either plastics or zinc must be studied in detail to determine which material will produce the lowest cost of manufacture. It is not uncommon for two parts, similar in appearance at a casual look, to have a considerable difference in energy requirements and production costs. Detailed cost estimates of the advantages of each material should therefore be prepared for zinc and plastic parts before the final design and material selection decisions are made.

Jan 1, 1978

By Rui-Qing Li, John G. Peacey, Peter J. Hancock

"Noranda has been investigating a pyrometallurgical process for the direct recovery of zinc from zinc concentrate and zinc and iron containing residues. The process consists of injecting dry zinc concentrate and secondary zinc materials into a molten iron oxysulphide bath, volatilizing metallic zinc into furnace off gas essentially free of sulphur or S02, fixing sulphur contained in the feed materials as iron oxysulphide matte which is disposed, and recovering metallic zinc in an ISP type lead splash condenser. Combustion of petroleum coke with air or oxygen enriched air inside the oxygen containing matte supplies part of the heat, and the products of combustion dilute the zinc-laden gas to a desired level.This paper describes the process concept, thermodynamic background, experimental tests, mass and heat balance calculation for a conceptual flowsheet, environmental stability of the residue and advantages and disadvantages of the process. Experimental tests have successfully proved the process concept and thermodynamic predictions. Direct smelting of zinc concentrate and residues inside an iron oxysulfide bath has a great potential to become a cost effective and flexible zinc smelting process.1. INTRODUCTIONZinc is mainly produced by a roast-leach-electrowinning process route, which accounts for about 80% of the world primary zinc production. This process produces high quality zinc with very high zinc recovery (>95%) but suffers from several major drawbacks such as using high cost electricity as reductant, producing environmentally problematic iron containing leach residue (jarosite or goethite) and the difficulty in treating secondary zinc feed materials containing high impurity levels, such as electric arc furnace dusts from the steel industry, and other complex sources. Also in some areas, markets for sulphuric acid are distant resulting in negative realizations on acid sales.The Imperial Smelting Furnace (ISF) process is the major pyrometallurgical process to treat zinc-lead concentrate. The advantage of this process over the electrolytic zinc process is its flexibility in treating high-lead, bulk concentrates with high recoveries of lead, copper and precious metals. However, this is a two-stage process involving sintering of Zn-Pb concentrates followed by blast furnace reduction. The process requires large amounts of high-quality coke which is a major operation cost, and the sintering process which results in serious environmental problems."

Jan 1, 1996

By Liming Yuan

Three-dimensional computational fluid dynamics (CFD) modeling is conducted to simulate spontaneous heating in a large-scale coal chamber with a forced ventilation system. Spontaneous heating is modeled as the low-temperature oxidation of coal using kinetic data obtained from previous laboratory-scale spontaneous heating studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. The water vapor transfer and the effect of heat of wetting are not modeled. The CFD model is validated by comparing simulation results with test results from U.S. Bureau of Mines experiments conducted in the coal chamber. The model predicts lower temperatures in the early stage but agrees well on the induction time for spontaneous heating. The effects of airflow rate and order of reaction on the spontaneous heating process are also examined. The calibrated CFD model is found to be useful for predicting the induction time for spontaneous heating in underground coal mines.

Jan 1, 2009

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963