Search Documents

J. L. McK. YARDLEY,* Pittsburgh, Pa. (written dlscussion ?) .-It is interesting to observe how closely Mr. Hansen agrees with other investigators to the effect that the art of electrolytic zinc has left the realm of mystery. In his introduction, lie has said practically what Thomas French said in his paper "The Future of Electrolytic Zinc. "1 The successful electrolysis of zinc from sulphate solutions has not been an easy matter, and it is only within recent years that the difficult problem of depositing high-grade zinc has been satisfactorily: accomplished on a commercial basis. The principal requisite is. that the electrolyte shall be quite free from certain impurities. The methods by which freedom from these impurities is assured are now very well understood, and with experienced superintendents there is little difficulty in obtaining a high efficiency in that part of the process. When certain underlying principles are recognized, the difficulty encountered in dealing with the filtration of the acid and slimy solutions also largely disappears, although it has been a very serious one to the uninitiated. In the dissolving of the zinc from the roasted ore, there is nothing which any competent chemical' engineer cannot undertake, and any other operations connected with the electrolytic process are either of little or no difficulty, or are common to the retort process. Mr. Hansen also agrees with R. G. Hall's statement in " Some Economic Factors in the Production of Electrolytic Zinc:"2

Jan 10, 1918

By John L. Baum

GEOLOGISTS and engineers working around a diamond drill rig have often had the opportunity to observe the magnetic attraction of drill rods pulled out of the hole for core removal. This is sometimes an amusing pastime, but this same magnetic force inadvertently applied to a compass needle can cause it to lose its polarity entirely or to become reverse polarized when placed in the immediate vicinity of stacked rods. The first recommendation, of course, would be to avoid the rods, but in surveying an operating drillhole this is not always possible; therefore steps must be taken to neutralize the magnetic effect of the drill rods. Early in the summer of 1949 the geological department of the New Jersey Zinc Co. undertook at Franklin, N. J., an extensive program of surveying the course of deep diamond drillholes. The majority of the holes were surveyed while in the process of being drilled, and considerable difficulty was encountered. A pattern for the deviation of drillholes had been established for the district from surveys in holes from which the drill rig had been removed. It was observed that a certain operating deep drill- hole being surveyed did not fit this pattern. In the resulting confusion of repeated surveys and cementing a plug for wedging operations, the lower 1800 ft of the hole was lost. Because of this incident studies were initiated to determine the source of the difficulties and to develop safeguards against recurrence of faulty surveys.

Jan 12, 1954

By Leo Brewer, Gerd M. Rosenblatt

Thermodynamic calculations predict the species vaporizing from metal-oxide mixtures when reliable free energy functions, enthalpies of formation, and dissociation energies are available for the possible gaseous and condensed oxide components. Calculations of the oxygen to metal ratio in the vapor phase compared with the oxygen to metal ratio in a liquid metal saturated with oxide impurity are presented The possibility of purifying metals contaminated with oxide by vacuum melting or by distillation is discussed. Kinetic considerations affecting rates are neglected. IN recent years extensive information has been obtained on the thermodynamic stability of gaseous oxides of metals due to a variety of new types of measurement. Perhaps the greatest amount of information has come from the application of mass spec-trometry to the study of high-temperature vapors.' In many instances oxides of quite unusual oxidation states are found to be important in the high-temperature vapors. At low temperatures the standard free energy change for a reaction as given by the equation ?F° = ?H° - T?S° is determined primarily by the AH" value. However, at higher temperatures where the value of T in the T?S° term is large, the entropy term becomes equal to or greater than the AH term. At low temperatures only reactions for which AH is negative or only slightly endothermic are of importance. This restricts the main equilibrium species largely to those with completed octets or those with the principle oxidation number of the element. At

Jan 1, 1962

By Joe L. Ratigan

INTRODUCTION Rock mechanics engineers are seldom concerned with obtaining the tensile or fracture strength of brittle rock at low mean stresses. The reason for this is two fold. Firstly, the behavior of many excavations in brittle rock is controlled by the inherent discontinuities in the rock mass. Because of the jointing and faulting, tensile strength is usually taken to be negligible. The second reason that tensile strength is seldom obtained in the laboratory is that the technology of utilizing this strength measure in design is undeveloped. Despite the fact that tensile strength of brittle rock is often ignored, there are a number of applications in rock mechanics wherein the knowledge of tensile strength is of fundamental importance. The apparent tensile strength must be known in a hydraulic fracture experiment if the state of in situ stress is to be determined from the initiation of the hydraulically induced fracture. In certain underground situations, the apparent tensile strength of intact rock beams defined by jointing or bedding planes is important in determining required rock bolting. Numerous other situations require a knowledge of apparent tensile strength including such high technology uses of underground space as geothermal energy extraction and LPG storage. Three observations are invariably made when intact rock samples are taken into the laboratory and tested to determine tensile strength. (1) The apparent tensile strength depends on the sample size (the 1 arger the specimen, the lower the tensile strength)

Jan 1, 1982

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

By Reamy Joyce

CONDITIONS in underground mining are so variable that in approach-ing the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-ures, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifica-tions. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem.

Jan 1, 1939

By Louis W. Cope

Placer material, regardless of the value of gold, tin, titanium, diamonds or other value mineral it contains, remains worthless until the valuable constituent is separated from the bulk of the material. This separation is no mean task when considering that a gold placer containing 0.01 to 0.03 oz/yd3 of gold, which is the range of grade of typical placer deposits; yes, 1:3,000,000! It is a miracle that gold placer mining has ever been profitable. Added to the situation of minute quantities of gold are several other problems, such as the gold often being very finely divided, the association of boulders and clay, and running and/or ground water. As each placer deposit is individual and distinctive, many factors have to be considered in planning the method for gold recovery from the alluvial deposit. Previous chapters have shown that in the exploration and sampling stage, some knowledge of the amount of each size of coarse and fine material which occurs in the deposit as well as the size distribution of the discrete gold particles is determined. Unless informed to the contrary, as a general rule of thumb, plant designers will consider that 40 percent of the material will pass through a 5/8-inch screen or punched plate hole. Also that there may be an occasional nugget and normally considerable amounts of fine gold. The designer must

Jan 1, 1992

By George W. Maynard

In the Journal of the Iron and Steel Institute for the year 1878, in the account of the proceedings of the annual meeting in March of that year, when Mr. Bell read his paper On the Separation of Phosphorus from Pig-Iron, occurs the following statement, as part of the reported discussion of that paper: " Mr. Sidney Thomas stated that he had succeeded in effecting the almost complete removal of phosphorus in the Bessemer process. Experiments had been carried on at Blaenavon, with the co-operation of Mr. Martin, on quantities varying between 6 lbs. and 10 cwt., and some hundred analyses made by Mr. Gilchrist (who had the conduct of the experiments from the first) showing the removal of from 20 per cent. to 99.9 per cent. of phosphorus in the converter. He believed the practical difficulties in the way had been overcome, and that Cleveland pig might be made into good steel without any intermediate process. He hoped on a future occasion to lay full details before the Institute." I was present at that meeting, and I doubt if any one in the hall knew, either by sight or name, the young man who had dared to rise in that august body and claim that he had accomplished that after which the great metallurgists of Europe had been unsuccessfully striving ever since Mr. Bessemer's great discovery. I remember distinctly the pitying smile of derision and the stony stare

Jan 1, 1885

By A. Kounosu, T. Fujita, J. Shimoiizaka, K. Nakatsuka

Stable aqueous dispersion of magnetite colloid of about 10 nm in diameter was obtained by allowing an anionic or nonionic surfactant to adsorb on the hydrophobic surface of magnetite particles prepared by monomolecular adsorption of oleate. Sodium dodecylbenzene sulfonate, sodium oleate and poly (oxyethylene) nonyl phenyl ethers whose hydrophilic-lipophilic balance (HLB) are higher than 12 were suitable for giving a second adsorption layer to obtain a stable dispersion. Stability of the colloidal suspensions depends upon pH of the solution and is controlled by the dissociation of the adsorbed surfactant in the second layer. The addition of ethyleneglycol, which was used for lowering the freezing point of the dispersion, did not affect the stability when used in amounts smaller than 60% of water. Preparation of diester-based ferrofluids was also attempted by the same procedure using a nonionic surfactant as second layer molecule. Hydrophobic magnetite colloid, which had been preliminarily coated with mono-molecular oleate, was suspended in di(2-ethylhexyl) agipate, azerate, and sebacate respectively, and dispersion stability was investigated by adding various poly (oxyethylene) nonyl phenyl ethers of different HLB values. It was found that those with HLB values between 10.9 and 13.3 were suitable for this purpose. Stabilities of the dispersions in a magnetic field were investigated up to 1 T by applying an electromagnetic field. No separation of dispersant was observed and each magnetite dispersion displayed the characteristics of a magnetic fluid.

Jan 1, 1980

By Emery C. Olsen

Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that influence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25 % and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the south- west. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development.

Jan 10, 1963

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By William E. Souder, Eugene R. Palowitch

INTRODUCTION The longwall method of mining coal underground is now a highly developed and accepted mining technology. However, it was only through a long history of successes and failures that this technology now has the potential for reversing the declining trend in underground mining productivity in the United States. From its early beginnings in the United States during the 1800's, several species of longwalls have evolved. The evolutionary record consists of a series of overlapping birth-death eras, with each era giving way to another unique longwall technology. Typically, an era begins when some new longwall technology appears in response to a new technical opportunity or economic need. This new technology is adopted initially by only a few innovators. Later, other imitators get on the bandwagon and the technology diffuses throughout the user population. But evolving technical demands and socio-economic circumstances eventually cause many of the adopters to discontinue its use. This paper chronicles seven eras in the history of the evolution and utilization of longwall technologies in the United States. Some of the important factors that have influenced this history are discussed. Some distinctions are drawn between the operators who were first to adopt longwalls (innovators), and the imitators who followed. Statistics are presented which show that longwall mining is being adopted at an exponentially increasing rate, substantiating the forecast for a significant number of new longwall installations in' the future. Potential barriers to this increased utilization of long- walls are noted.

Jan 1, 1981

By F. B. Speaker

MUCH of White Pine's success is due to the mechanization of mining operations and the development of an efficient beneficiation process to extract usable copper from the low-grade ore (averaging slightly more than 1 pct copper content). When the mine was first opened, all ore was trucked to a conveyor system installed in the slope leading out of the mine. But as new mining areas have been opened up at increasing distances from the slope, conveyors have replaced the trucks for much of the haulage. This conveyor program is expected to continue as mining progresses. Here is how the present underground system functions: Run-of-mine ore is dumped into two truck hoppers and withdrawn from the bottom of each hopper by a 60-in. apron feeder 22 ft long (see diagram). Collecting conveyors 54 in. wide and 44 ft long receive the material from the apron feeders and discharge to two main-line 54-in. conveyors, one 2000 ft and the other 2600 ft long. Operating at 312 fpm and handling 1200 tph, the main-line conveyors converge near the bottom of the tunnel leading out of the mine and discharge into two 72x168-in. Vibrex screens. Ore under 8 in. goes directly to the bin beneath. The oversize is fed to two 32x40-in. jaw crushers and after crushing joins the 8-in. material in the bin.

Jan 12, 1957

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

By J. Schleifer

On short term, planning techniques require more details to ensure feasibility, giving importance to operation constraints and use of available resources. In GUEMASSA (Morocco), the ore mass is mined by cut-and- fill method. Correct organization requires to forecast a few weeks ahead the schedule of blocks to be mined, in order to respect ore quantity and grade constraints. While operating constraints are tackled, feasibility is assumed with an average production capacity suggesting that resources will be available. In ST-SALVY (France), scheduling operations is not possible if not considering account resource allocation. In any stope within the vertical vein zinc deposit, the cut-and-fill method enables to mine each horizontal slice according to various strategies, de- pending how to use manpower and equipment, and selecting among predefined scenarios known as realistic. For KOFFIEFONTEIN (South Africa), the kimberlite pipe is mined by a sub-level-stoping method. To achieve the production target, precise organization over one month is obtained, using on& resources when available and respecting all mining rules. This combined operation scheduling and resource allocation is called sequencing. While following the BONANZA concept, providing a planning- retrieval process, sequencing offers more. Very detailed, it is possible to check the impact of resource parameters and mining rules. The sequencer, like a simulation platform, enables expertise. Each sequencer must be tailor-made to fit to each specific mine. The next challenge is to produce a generic environment.

Jan 1, 1996

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By W. G. Fischer, S. R. Felde

Trona ore at the Westvaco, Wyo., mine of FMC Corp. has been obtained by room-and-pillar methods since the mine began operation. The flat- lying, 10-ft thick trona (Na2CO3.NaHCO3.2H2O) is covered by 1500 ft of weak shale and sandstone, and extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly, and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs, efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early '60s forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were also seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. However, since roof control in the longwall methods appeared to be more satisfactory than that found in room-and-pillar techniques it was believed that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 4, 1966

By A. L. Field

A. W. FAHRENWALD, Socorro, 'N. M. (communication to the Secretary*).-When asked to discuss Mr. Feild's paper, I felt most highly complimented to have the privilege of commenting on such a worthy and needed piece of apparatus. In consideration of the importance of the viscosity of blast-furnace slags and the relation existing between the' melting point of a slag and its viscosity, the introduction of this apparatus should be a welcome means or assistant in the study of the physical properties of a slag. Up to the present time, it is A fact that this side of the practical working of the blast furnace has been sadly neglected by those investigating slags. It is easily seen that the fluidity of a slag is of as great importance as its melting point. It is not necessarily true that a slag having a low melting point will have a correspondingly low viscosity or be highly fluid. For example, a slag having a melting point of 1,100° C. may have to be superheated to, say,1,300° C., in order to have as high a fluidity as another slag whose melting point is, say, 1,250° C. The latter in this case would be the more economical. This point has been brought out very nicely by Mr. Feild. Before discussing this paper further, I think it will be well to outline some of the points, a discussion of which may be in order:

Jan 3, 1917

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003

GEORGE OTIS SMITH, the Institute's new presi-dent, continues the long tradition of close asso-ciation between the organization and economic geology. Several preceding presidents have been eco-nomic geologists, and a gen-erous share of space in the TRANSACTIONS has always been devoted to that subject, one of critical importance to the miner as well as the seeker for ore. Mr. Smith has long served the Institute, hav-ing been a director since 1921 and first vice-president since 1927. He was born in Hodg-don, Me., on Feb. 22, 1871, and graduated at Colby College, where he took his A.B. and A.M. He did graduate work at Johns Hopkins, where he re-ceived a Ph.D. in 1896. Meanwhile he had engaged in field geological work in Michi-gan, Utah and Washington with the Geological Survey. In 1896 he joined the regular staff of that organization, be-coming director in 1907. He has been with the Survey con-tinuously since he first joined, with the exception of one year when he was furloughed to serve as a member of the U. S. Coal Commission. His special interest for many years has been in the eco-nomic aspects, in the larger sense, of the mineral in-dustry, matters that are necessarily the subject of strong differences of opinion, but which he has dis-cussed with good temper though with full adherence to his strong con-victions.

Jan 3, 1928