Search Documents

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modem technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example of a European approach to these matters the paper presents Outokumpu' s response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Raymond A. Bradbury

A significant news item appearing in a coal mining journal in November 1969 stated simply that a Caterpillar D-333-CNA engine had received Bureau of Mines Schedule 31 approval. This item occurring at the time a new mining property in Martin County of East Kentucky was being prospected and prepared for mining, resulted in the manage-ment of Martin County Coal Corporation asking the question, "Why not use diesel equipment in our new operation?" Martin County Coal Corporation is part of the A. T. Massey Coal Company, Incorporated organization. The property being developed is on a 17,500 acre leasehold obtained from Pocahontas Land Corporation and lies in the Wolf Creek area of Martin County. The Norfolk and Western Railway Company built a 24-mile railroad into this undeveloped section of Kentucky to tap a huge reserve of steam coal. Duke Power Company is the customer who will take all of the production from Martin County Coal Corporation mines which ultimately is projected to be 2,000,000 tons annually. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton are being deep mined now and it is in those mines that the diesel haulage equipment was introduced. This paper will endeavor to trace the steps loading to the introduction of the first diesel-powered Wagner Mining Equipment Company ScoopTram in a coal mine in America. It will further elaborate on the features which make this unit a very versatile and useful utility unit as well as the safety features which are incorporated in the machine. The success of this first unit led to the placing of

Jan 1, 1972

By F. Ngoroma

Concentrators processing PGM bearing ores make use of polysaccharide depressants to reduce the recovery of the undesired naturally floatable gangue minerals, mainly silicates, present in the ore. Recent work has shown that high depressant dosages can completely depress naturally floatable gangue and thus prevent it from reporting to the concentrate. These high depressant dosages can, however, have a negative effect on the recovery of valuable minerals present in the ore by reducing the stability of the froth. In order to counterbalance the effects of depressant addition, frothers are added. It is, however, preferable to maintain independent control over bubble size and froth stability which is difficult to achieve with only one frother. An alternative strategy is, to use a blend of frothers, e.g. a weaker frother in combination with a stronger frother. Such a system allows an additional degree of freedom: changing the ratio of the two frothers, that would provide more independent control of bubble size and froth stability. This study demonstrates, through the use of batch flotation tests, how blending low molecular weight alcohols with commercially available frothers impact the solids and water recovery, as well as the valuable mineral recovery and concentrate grade in different PGM ores. Higher water and solids recoveries together with higher valuable mineral recoveries (>90% copper and >70% nickel) were obtained from tests using frother blends.

Sep 1, 2012

By D M. Frantois-Bongarton

Variograms can be powerful tools for the analysis and control of process streams and their sampling. Their uses and proper utilisation have been described somewhat unclearly to date, and their limitations and precautions of use are too rarely mentioned. The general meaning and properties of the variogram tool and its use in geostatistics are therefore reviewed in details to derive a critical view of its proper use for process control: what to expect from it and what it cannot deliver and which uses are illusory or potentially misleading. A summary of GyÆs seminal work accompanies this essay to put the concepts into historical perspective.CITATION:Frantois-Bongarton, D M, 2012. Review of variogram properties and remarks on its use in process control, in Proceedings Sampling 2012 , pp 175-180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By J. Chretien

The ability to continuously monitor the air quality within a mine has become instrumental in becoming a low cost producer. The many considerations involved in monitoring air quality include sensor type, hardware placement, as well as data storage medium. BESTECH has had the opportunity to gain insight into these air quality monitoring considerations through deployments of NRG1-ECOTM, a minewide energy consumption optimization system. This paper explores the particular challenges overcome through these installations, and provides a set of guidelines for mines that want to maximize data capture while minimizing costs. It provides a view of additional benefits of air quality monitoring, such as ventilation control, reporting and trending.

Aug 1, 2013

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By Y. Foucaud, C. Eswaraiah, L. Filippov

Enhanced gravity separators such as Falcon concentrator which uses additional centrifugal force, are the most common gravity concentration techniques used for fine particles processing. Hence, understanding the kinetics and separation mechanisms within these separators is of paramount interest. Recent research yielded a predictive physical model for the Falcon Ultra Fine (UF) which however does not explain some results obtained with industrial ores. This study aims to identify the mechanisms involved in Falcon UF separation with the objective of confirming or rejecting the hypotheses on which the current model is built and suggesting potential points of improvement. The Falcon UF kinetics is investigated through the processing of complex low-grade and fine-grained ores from the Altenberg tin deposit (Germany), the Tabuaço tungsten deposit (Portugal) as well as a synthetic iron ore. Saturation tests are performed on the Falcon UF by controlling the separation efficiency in terms of recovery and enrichment ratio with time or feed mass. Results show an evolution of Falcon UF performance with time in contradiction with the stationary separation hypothesis on which the physical model is based. Observation of the concentrate bed suggests the presence of erosion figures in furrows which may play locally an active role in the separation. In terms of Falcon UF separation timing, three phases can be distinguished. First, upon initial feeding of the bowl, a bed quickly grows unselectively and ultra-fine particles are ejected from the bowl until the bed reaches its final profile. Next, actual separation occurs with selective concentration of dense particles. Finally, capture sites saturate and recovery drops. The evolution of partition curves over time confirms the existence of two separation mechanisms. First, differential particles settling within the flowing film responsible for the ejection of small size particles during the whole separation cycle which is already accounted for in the physical model. The second mechanism involved may be explained by the action of lift force, neglected in the physical model, which acts preferentially on coarse particles deposited at the surface of the bed resulting in coarser particles being rejected in the tailings. Hence, the addition of a lift force component to the existing model is suggested to account for this second separation mechanism.

Jan 1, 2018

By Ángel Ruiz-Sánchez

Ethylene glycol additions to aqueous acid solutions for leaching copper sulfides increase both copper and iron extractions compared to a conventional sulfuric acid leach with hydrogen peroxide (H2O2). The role of ethylene glycol is to prevent peroxide destruction, which normally occurs in solutions that contain both cupric and ferric ions. However, despite this improvement, ethylene glycol and sulfuric acid concentrations must be high (3.5 M and 0.7 M, respectively) to obtain satisfactory conversion levels at room temperature. In the present investigation, EDTA was used as an additive to complex the cupric and ferrous ions, lowering the requirements of ethylene glycol and H2SO4 to 0.11 M and 0.007 M, respectively, while minimizing oxidant decomposition. The experimental results for a mainly chalcopyrite, copper concentrate showed complete copper extraction in 24 h at room temperature, with the stoichiometric quantity of EDTA for the copper and iron dissolved. Tests using seawater were equally as successful.

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By M. Beale

Fuzzy logic and neural networks are new technologies being applied in many areas of engineering and business. While it is not always clear which kinds of problems are best suited to these technologies, and which problems are best approached with more standard methodologies, both fuzzy logic and neural networks appear to show great promise in the field of control systems. This paper demonstrates two advantages that these technologies offer: Easy controller design in the absence of a mathematical model of the plant to be controlled, and adaptive control capable of quickly responding to changes in the plant.

Jan 1, 1994

By J. A. Pigott, R J. Hall

The International Nickel Company of Canada, Limited operates five underground mines on the rim of the Sudbury Basin in the northern part of the Province of Ontario. Four of the mines, the Frood-Stobie, Creigh-ton, Murray and Garson, are located on the south range of the basin with-in a radius of IO miles of the centre of the city of Sudbury. The fifth mine, Levack, is on the north range about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite and pyrrhotite. In 1960 the total ore production was in excess of 16 mil-lion tons, 95 per cent of which was produced from the five underground mines and the balance from the Frood-Stobie Open Pit. Mining at this open pit is nearing completion and underground production has been expanded to replace the open pit tonnage.

Jan 1, 1961

By Betty L. Gibbs

A company must have an organized approach to effectively sort through the profusion of available software and hardware and find the programs and equipment which fit defined needs. The selection process must build a complete compatible system which includes hardware and software. The methodology presented in this paper helps identify some of the more important considerations. The steps needed for an organized approach to software/hardware selection are: •All involved staff should contribute to an assessment of current computer capabilities and projection of future needs. •Alternatives are analyzed to determine what software and hardware is available and how selections may possibly be merged into the existing computer system. The evaluation process focuses on details of program capability and hardware compatibility. Analysis must be done to determine how closely individual programs fit the established requirements. The final decision is often a balance of needs between program capabilities and hardware availability. Any programs selected must be able to run on existing and newly purchased hardware. Any additional hardware selected must be capable of meshing with the available computer system.

Jan 1, 1983

By H. W. Leavenworth

Research was conducted by the Bureau of Mines to develop a technique to grow metallic fibers from a sulfide mineral. In this research, chalcopyrite (CuFeS2) was made sulfur deficient, and the remaining sulfur partitioned to the iron in the mineral to liberate metallic copper, or to the copper to liberate metallic iron. The metals formed on the surface as fibers and in the interior as spherical particles. Fiber growth is very fast. Lengths of 3 to 4 cm form in a matter of minutes, and the diameter of individual fibers is less than 1 µm. The mechanism of fiber growth is explained, and the reactions are reversible as predicted. Copper fibers can be made to grow from the surface at 400° C or to dissolve back onto the solid surface and be replaced by iron fibers at 625° C. Growth and dissolution can also be controlled to form copper/iron duplex fibers.

Jan 1, 1974

By J T. Carswell, K Sutton

Quality control (QC) of reverse circulation drill sampling commonly involves regular duplicate subsampling to monitor the extent of imprecision or random error in the subsampling system. In gold mining in Australia, the subsampling tool is usually a cone splitter.Other sources of error, including delimitation error and bias (systematic error) in the subsampler are often assumed to be negligible or ignored for being too difficult to QC.This paper describes actual sampling errors and error mitigation based on quality assurance and quality control (QA/QC) of surface and underground reverse circulation drill sampling at a high-nugget gold mine at Sunrise Dam, Western Australia.CITATION:Carswell, J T and Sutton, K, 2014. Sources of sampling error and implications for quality assurance and quality control in surface and underground reverse circulation drilling, in Proceedings Sampling 2014 , pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modern technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example ofa European approach to these matters the paper presents Outokumpu's response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018