Search Documents

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005

By T Burns, P Savory

In 2013, Rio Tinto Iron Ore (RTIO) produced 251 Mt from 15 mines in Western Australia. Throughout the mines, Ore Reserve models are used for long-term and medium-term mine planning. Grade control data aids the accuracy of short-term planning. Reconciliation of models with grade control data is important for maintaining confidence in predictions from the models, understanding the limitations of the models, and identifying issues that may require further work.There are a large number of sites and models, with more than 200 professionals involved in different parts of the reconciliation process. Regular meetings of all involved and enabling effective communication are important in the reconciliation process.Reconciliation data is gathered and processed through a web-based system; Grade Block Reconciliation System. This system cuts each grade block against the required model, stores the results, and allows users to view and analyse the data. Development of this system has occurred over a number of years and all Rio Tinto Iron Ore mine geologists and resource geologists now use it as standard to report reconciliation results. The results can be viewed in many ways including by different time periods or benches. Graphing the results assists identification of trends. Centralising and standardising reconciliation has allowed easier comparison between sites. Flexibility in the system allows users to customise reports to manage issues unique to their particular site.In parallel with system development, substantial effort has been put into ensuring mining professionals get together to discuss and understand reconciliation issues. To facilitate this there are now regular sessions, including site visits. Issues are assessed on a case-by-case basis and decisions on how best to address the issues are made by the relevant stakeholders. Reconciliation reports and action plans are revised each quarter.CITATION:Burns, T and Savory, P, 2014. Reconciliation of orebody model predictions – system and people, in Proceedings Ninth International Mining Geology Conference 2014 , pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By John Cogan

INTRODUCTION Lake tapping is a method of blasting an intake into a body of water from below the natural water surface without first lowering that surface or installing a protective cofferdam around the tap hole. Lake taps are done by first excavating a tunnel almost to the water/rock contact and then blasting out the final protective rock plug at one time to allow water to suddenly inflow into the tunnel from the lake. This procedure can be done "dry" or "wet." In the dry method the tunnel is empty of water before the final plug blast while in the wet method it is partially filled with water. This paper describes a wet method lake tap as performed at Alaska Power Authority's Tyee Lake Hydroeletric Project in southeast Alaska. The Tyee Lake project is located approximately 40 miles southeast of Wrangell, Alaska, in a glacially formed valley called the Bradfield Canal. The project consists of a powerhouse located at sea level on the canal, a system of tunnels and shafts connecting the powerhouse to Tyee Lake at elevation 373 m (1225 ft), and an 129 km (80-mile) electrical transmission line leading from the powerhouse to Wrangell and then Petersburg, Alaska. Tyee Lake itself is a natural lake gouged out of the rock by glacial ice during the last ice age. The objective of the project was to tap into the lake and use the water as a source for power production. The techniques used for lake taps have been developed in Norway where conditions are favorable for their use in hydroelectric proj¬ects. Over 100 have been performed. In the United States the Tyee

Jan 1, 1984

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The 'actual performance' speed-curve of aircraft plotted over a ten-year period is rising faster than the 'expectancy' speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By Eugene A. Lang

Mr. Chairman, ladies and gentlemen. As a member of the uranium and coal producing community, I am pleased to participate in a session dedicated to a look at these and other mineral markets.(title slide) before sharing some of my thoughts with you, let me tell you a little bit about rocky mountain energy company. It was established as a subsidiary of union pacific corporation in 1971 with responsibility for coal, uranium, and industrial minerals. We participate in four coal mining operations and a uranium mine and mill all in Wyoming, and an aggregate and an abrasive operation in Utah.

Jan 1, 1984

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By Edward D. Thimons

Several types of inflatable stoppings, developed under Bureau of Mines contract for use as mine air barriers during underground production, have been tested by the Bureau. All of the stoppings tested showed significant internal leakage initially but, in all but one stopping, the leaks were sealed with limited effort The stoppings were tested underground in two western noncoal mines under production conditions. The results from the Colorado molybdenum mine showed the stoppings to be generally unsatisfactory for daily mine usage if they are deployed near blasting areas or in locations where near-perfect air seals are required. They were very susceptible to blast damage and seldom were better than 90 percent efficient as air barriers. However, stoppings tested in the New Mexico uranium mine were located substantially distant from any blasting. Because slight leakage past the stoppings was acceptable, they proved very satisfactory in that application.

Jan 1, 1976

By M. Shabbir

A study was made to determine the optimum conditions for precipitation of uranium from mill solutions using hydrogen peroxide. Precipitation tests were made on both synthetic and actual mill solutions. Parameters studied included amount of hydrogen peroxide, initial pH, reaction pH, time, and temperature. Also investigated was the effect of varied amounts of vanadium, molybdenum, and sulfate in the test solution on uranium precipitation and product quality. The optimum conditions for complete precipitation and high product quality were (1) the use of 150 percent of the stoichiometric requirement of hydrogen peroxide, (2) initial pH of 1.0, (3) reaction pH between 3.4 and 5.0, (4) 4 hours reaction time, and (5) ambient reaction temperature. The excess hydrogen peroxide requirement is partially dependent on the amount of impurities present in the feed solution. The hydrogen peroxide process appeared applicable to treatment of the several mill eluate and strip solutions tested. The experimental studies also indicated that the hydrogen peroxide technique gives substantially better product quality than that produced by ammonia precipitation.

Jan 1, 1974

By K. Fuenkajorn

Geomechanics and geohydrological considerations for the seal design for mine openings are presented. Design guidelines derived from laboratory and in-situ experiments are proposed. The results suggest that seal design, specifications and material selection should be site-specific. Performance requirements for a specific seal location should be identified. Evaluation of sealing effectiveness should be made on the entire seal system, i.e. seal, seal-rock interface, excavation-induced damage zone and the surrounding rock.

Jan 1, 1997

By A. T. Yu

There are compelling reasons for us to look to our Country's Western coal. Despite its inherent low BTU content, Western coal's low sulphur content provides a near-ideal answer to satisfy our in- dependent goals of clean air and self-sufficiency in energy. Vast reserves, thick seams and amenability to low-cost strip mining serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be quite obvious, is transportation cost. These abundant deposits are remote from the utilities of the heavily populated eastern regions of the United States (Figure 1). A Western coal mine in Montana is likely 1500 miles or more from an eastern power plant. The comparable distance to an eastern coal mine may be only 200 miles. Thus, the question is: How can the haulage cost of our Western coal be substantially reduced to an acceptable level? If resolved, western reserves of coal will be one of the key solutions to satisfying our Nation's energy needs.

Jan 1, 1975

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993