Search Documents

Some form of technical library is a necessity for every metallurgical plant, but its form and scope will vary with the conditions of each case. In its simplest form, it may consist of one or two mining journals and a few text books distributed amongst the staff. Again, it may be a separate establishment controlled by a clerk, the technical staff necessarily making its own research into the literature available. A still more elaborate organisation may be established both to supply information when requested and to keep the operating staff in touch with current matters of interest, and the library service of the Electrolytic Zinc Co. of Australasia is of this character.The necessity for such a service is due to several facts. The Company's interests are scattered over three States. Most of its staff members are remote from: good public library facilities and they have few opportunities for exchanging ideas verbally with other metallurgists and engineers. Then, too, the process of recovering zinc by electrolysis, is a young art of which the physical and chemical bases were far from fully known at the time the: Risdon plant was established. Most of the zinc produced is sold abroad, and this unsheltered industry can afford to miss no technical or economic development which may promote its efficiency. Add to these facts the geographical isolation of the Commonwealth and the case for an adequate library is complete.

Jan 1, 1934

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

By Dale Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was first attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The configuration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the first four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition.

Jan 1, 2006

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

The Cowarra gold mine is at latitude 36°O'S. and longitude 149°19'E. which is roughly 20 miles north-north-east of Cooma.The deposit was· originally worked towards the end of the last century, but the presence of sulphides associated with the gold in the primary zone caused cessation of work when that zone was reached.GEOLOGY AND MINERALIZATIONThe principal country rocks are sandstones and shales of Silurian and Ordovician age, both very strongly folded with structural pitches ranging from a few degrees to almost vertical. The mine proper is within Silurian rocks and the main orebody (there are several minor parallel bodies) is developed within a shear striking approximately north, dipping approximately 70° east, and ranging in width from 2 ft to 15 ft but averaging about 4 ft.This shear is impregnated with quartz and sulphides with which the gold is associated. The predominant sulphide is pyrite though pyrrhotite is commonly present in quantity.Arsenopyrite and bornite are present in smaller amounts.Stillwell (1936, 1937a, 1937b, 1938, 1941) has published five mineragraphic reports on the ore.The various levels have been mapped in detail (Figs. 1-3) and the No. 2 level plan (Fig. 1) shows the general relationship of shearing, as now indicated by mineralization, and faulting. There is no apparent connection between the fold structures and mineralization.Fig. 3 is a longitudinal projection showing the distribution of gold expressed as inch-ounces. The estimation of...

Jan 1, 1965

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

Metana Minerals commenced life in 1970 and graduated to a mining company in 1981 with the opening of a small alluvial tin-tantalite mine at Wodgina (W.A.) The present board of directors assumed control of the company in 1978 and established the exploration and development philosophies that have guided the company's expansion to its present status as an emerging diversified miner. An ability and willingness to raise equity capital when required has been a feature of the company. Company activities include exploration for gold, diamonds, heavy mineral sands, polymetallic (base and precious metals) deposits, strategic minerals, rare earths, oil and gas in a geographical distribution covering the entire Australian mainland Metana owns and/or operates four gold mines (Reedy, Mt Magnet, Youanmi and Howley) and at the time of writing is developing a fifth gold mine - its first underground mine - at Rothsay. In contrast to many similar or larger sized companies, Metana undertakes most activities itself rather than through the use of consultants or contractors. In-house services include: analytical and metallurgical laboratories, plant engineering design and construction, drilling and mining (earthmoving) Metana Minerals has established an enviable reputation for technical excellence and this expertise has placed the company in a sound position to continue its growth pattern into the future. This growth will be achieved through a combination of low cost and successful exploration and acquisition of suitable mines either directly or through corporate activity.

Jan 1, 1989

By H. A. Doerner

"Statistics show3 that in 1927 the United States consumed 60 per cent of the world's production of chromite and produced none. The uses of chromium are rapidly expanding, and a dependable supply is essential to our industries. Since the political and commercial control of our supply of chromite is now in foreign hands it is prudent to determine how this nation can best prepare to supply its need for chromium if the imports were cut off or restricted and whether it is now possible and desirable to stimulate production of chromium from domestic deposits. We have only small amounts of chrome ore of high enough grade to meet present trade requirements. Therefore the Bureau of Mines is making a study of methods for beneficiating our low-grade ores.Chromite (Cr203.Fe0), is the only commercial source of chromium. For refractories, a minimum of 40 per cent Cr203 and a low silica content (5 to 8 per cent) is usually specified. In most instances bricks or lumps having a physical structure that will not crack when heated are required. The only way an inferior ore could be adapted to this use world be to concentrate it and develop a satisfactory binder to make bricks out of the concentrates.For making ferrochrome the requirements are a minimum of 45 per cent Cr203 and an iron content not exceeding one-third of the chromic oxide. On some low-grade ores gravity concentration will give a product meeting these requirements; other ores yield concentrates containing too much iron or other impurities to be saleable."

Jun 1, 1930

By S. Chatterjee, F. Suparno, A. Paithankar

Estimating reserves and quantifying resources stand as pivotal and intricate endeavours within the realm of coal mining operations. Intricate geological formations compound the challenges in resource estimation, thereby complicating reserve calculations. The uncertainties tied to geological attributes of coal, encompassing parameters like tonnage and coal quality, wield significant sway over resource and reserve computations within coal mines. This research delves into the domain of geological uncertainties, with a specific focus on calorific value, aiming to numerically characterise resources and reserves within an open-pit coal mine situated in Indonesia. To quantify resources, the coal seam geometry underwent simulation via a multipoint geostatistical technique known as single normal equation simulation. A geologically established coal seam served as the training image for generating 20 equiprobable coal models. To simulate CV, 50 realisations were generated for each simulated coal seam, utilising sequential Gaussian simulation. Deviations of the simulated coal seams ranged from -0.07% to 5.48% in comparison to the training image. The CV simulation yielded an average value of 5,920.29 kcal/kg, accompanied by a standard deviation of 586.54 kcal/kg. However, the average CV spanned from 5,305.26 kcal/kg to 6,526.55 kcal/kg across diverse simulations. For reserve calculation within the context of geological uncertainties, an algorithm rooted in maximum flow graph theory was employed to construct the ultimate pit for the coal mine. Within this final pit, the average stripping ratio was 1.62, coupled with a CV value of 6,019.66 kcal/kg. When juxtaposed with the deterministic model, the findings underscore that the stochastic ultimate pit delineates a more expansive excavation, accompanied by a heightened undiscounted cash flow.

Oct 2, 2025

By T. E. Kobrick

When Ralph Banks called and asked if I would agree to present a paper on environmental health in the coal industry, I was reluctant because I have not been actively involved in coal mine dust control on a day-to-day basis for a number of years. Ralph reminded me that I am one of the few industry people with an industrial health background who remembers the pre-1969 Federal Coal Mine Health and Safety era. This marks the second time within the past year that I have had a similar request based on the same basic reasons. While I was pleased to have been remembered, I'm beginning to feel like the football player who has played one too many games. In responding to Ralph's request to present an overview of the past, present and future of environmental health in the coal industry, I have attempted to take the broad approach of someone who, having been intimately involved in an area of endeavor for a number of years and then leaves, has an opportunity to revisit that area at a later date to see what has changed and what remains the same, what have been the successes and the failures. Since none of us can foresee the future, trying to project too far ahead is fraught with frivolity, except that unless one is foolish enough to accept a future invitation to review those predictions compared to actual events, no one will recall how accurate or inaccurate those projections might have been. I can assure you that I will not ask to accept that challenge, so you can rest comfortably that five years from today you will not be asked to sit through a similar presentation by me - and that's a promise.

Jan 1, 1985

By G Williams

Somewhat to the surprise of many heavy mineral sands (TiO2 and zircon) producers, there are important geological structures within their typical placers and aeolian sands deposits that affect plant metallurgical performance. After many years of operations, even experienced producers have encountered unexpected changes in production, product quality and recovery. After looking in all the obvious (but wrong) places, it is recognised that the mine has advanced into ore with different separation characteristics. Metallurgical process response can vary significantly between ore sourced from different geological domains. The mineral characteristics that are exploited for effective separation may be associated with differences in the depositional environment, or be post-depositional in origin. Surface coatings that interfere with electrostatic separation might be associated with paleo-water table movements. Major storm events in the deposition history can also leave distorted mineral assemblage through stranded formations or incisions in older deposits.Apart from the influence on capital and operating costs, geometallurgical variances add another dimension to orebody modelling. Each domain could have specific recovery, mineral assemblage and product quality values to be considered in the value model. Project success is often directly dependent on understanding the geometallurgy of the resource. Tailoring the exploration and early process flow sheet development programs to account for such variances should be standard practice. Such practices have had a chequered history in the mineral sands industry, with sophisticated processes having been developed, only to be shelved for ‘economic’ reasons, and then once again ‘discovered’ when problems re-emerge.It is clear that knowledge gained through a higher level understanding of the changing mineral separation characteristics and advance warning of mineral behavioural differences can mean the difference between lost recoveries and disappointed customers or well timed capital plans and maximised revenues.

Oct 5, 2011

By F. Stanley, A. Noble, G. Luttrell

"The supply chain for coal-fired power stations involve a multi-stage network of mining units, preparation plants, blending facilities and transportation systems. Attempts to optimize the supply chain have historically been difficult due to the lack of communication/coordination between the various groups involved in coal production, transportation and utilization. In light of this issue, a new approach for globally optimizing the coal supply chain called Micro-Price Optimization has been developed to simplify the optimization problem and to provide coal producers with fundamental insight needed to improve the profitability of their operations. This fundamental concept assigns unit values to each particles (or groups of particles) passing through production units. Optimization occurs whenever the maximum tonnage of positive value particles are recovered and passed to market, while the minimum tonnage of negative value particles are recovered. Elements considered by the concept include factors such as target boiler cost/efficiency, waste disposal costs, coal quality parameters, emission penalties, transportation charges, or other quantifiable impact factors. This article reviews the basis for the micro-price concept and provides a detailed industrial case study involving the determination of optimum coal qualities that need to be supplied by mine operators to feed a coal-fired power station. INTRODUCTION The performance of coal preparation plants have long been known to play an important role in determining the overall profitability of mining operations. This significance is due to the fact that the misplacement of just 1 ton/hr of clean coal to reject resulting from poor plant performance can represent nearly $300,000 per year in lost revenues for a mine producing a steam market coal (i.e., 1 ton/hr x $50/ton x 6,000 hr/yr = $300,000/yr). This loss can be even more pronounced, occasionally approaching $1 million per year for each 1 ton/hr of misplaced clean coal, for operations producing high-quality coking coal products sold into the premium metallurgical market (i.e., 1 ton/hr x $150/ton x 6,000 hr/yr = $900,000/yr). Detailed economic studies indicate that improvements in plant yield resulting from increases in organic efficiency have one of the largest overall impacts on mine revenue when compared to other cost centers within the mining operation. One of the first studies to show this important financial impact was reported by Norton-Hambleton Consultants (Norton, 1979). Their study indicated that an unfavorable change in plant efficiency was second only to coal transportation in terms of its impact on profitability, while an unfavorable change in the cost of underground mining was a distance third. This longstanding realization has continued to provide a strong financial incentive for coal producers to optimize the separation efficiency of their coal processing and blending operations."

Jan 1, 2015

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

By P W. Wypych

The iron ore industry faces significant challenges in the control of dust to meet emissions regulations and goals, as well as ensuring sustainable operations. This paper describes some of the different techniques and innovative technologies that are being developed and implemented to improve the suppression of airborne dust, specifically through the use of high energy micromist sprays. The utilisation of computational fluid dynamics (CFD) modelling and simulation is identified and described as a key enabling technology for an improvement in dust suppression solutions both from a level of understanding the source and flow of dust emissions, and for the development of new systems that can be used in the iron ore industry. CFD modelling is shown to be effective for modelling both spray dispersion and cross-wind effects, allowing designers to develop high-efficiency dust suppression systems with a greatly improved level of confidence when compared to traditional techniques. New high energy micromist technology is also outlined as a key element in developing high-efficiency dust suppression systems. Experimental results and industry applications are presented to demonstrate the significant improvements that can be achieved in suppressing or reducing airborne dust emissions.CITATION:Roberts, J M and Wypych, P W, 2017. Research into improving the efficiency of water spraying airborne dust control techniques in the iron ore industry, in Proceedings Iron Ore 2017, pp 359–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017