Search Documents

By Faisal Shalzad, Adnan Anwar Malik, Tadashi Maejima, Jiro Kuwano

Single helix screw piles carry most of the structural load through end-bearing if the helix is embedded in the dense bearing layer. The tip condition of the central shaft of the screw pile can be closed, closed with cutting blades, opened with flat cut, and opened with wedge shape cut and its selection is based on the insitu ground conditions. These different end conditions of the central shaft disturb the ground differently, leading to the change in bearing capacity. In this study, an attempt is made to investigate the effect of open and close-end screw piles on installation effort (installation load and torque) and bearing performance in the dense bearing layer. The model steel screw pile with a pile shaft diameter of 21.7 mm and helix diameter of 43 mm is used in this study. Test results show that the open-end screw pile required less installation effort than the close-end pile that penetrated the bearing layer by 1Dhwith an unplugged condition. Further, the open-end screw pile shows a higher bearing response than the close-end screw pile if it enters the bearing layer with an unplugged condition.

Oct 1, 2022

By Elnaz Saminfar, Jae Bateman, Eric Westergren, Mark Trim

This paper presents a case study of two major Australian infrastructure projects that used digital engineering to facilitate design delivery: WestConnex Project (Rozelle Interchange), and Sydney Metro West (Eastern Tunnelling Package). The paper presents project overviews and building information modeling (BIM) execution and focuses on modeling techniques, software utilization, data management strategies and how the digital models helped the design-build team mitigate impacts to schedule by identifying clashes between disciplines before the execution of work. Finally, it demonstrates the positive and transformative impact of digital engineering on the design and construction of large underground infrastructure projects and highlights its role in asset management throughout the project lifecycle.

Jun 23, 2024

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. No doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data.

Jan 1, 1967

By Ri McCrindle

"Analytical Chemistry is moving rapidly towards a concept where technicians have to do no more than press a button and print the result from an instrument that is a featureless ""black box"". In this environment we must ask how much traditional ''wet chemistry"" is still required for undergraduate students.Methods that can be fully automated will become increasingly important. An example of such a method is that of the slurry nebulisation and ICP-OES analysis of precious metal concentrate. Grinding the sample and adding Triton X100 as dispersant, complete analysis time is in the order of 90 min as apposed to the traditional Carius tube method which could take as long as 24 h. For most of the elements studied, the results using ""in-house"" reference material for calibration and as samples as well were within the 95% confidence level. Elements of low concentration in the sample (As, Bi and Se) were not within that level."

Jan 1, 2014

By BUREAU OF MINES

PLATINUM

Feb 1, 1922

By A J LYNCH

It was Harold McMillan, Prime Minister of England 30 years ago, who used the phrase "The Wind of Change" to describe political events in Africa in his day. So well did this phrase capture the spirit of the time that it echoed around the world, and the echo has never stopped. Change is the constant factor in the society in which we live and everyone of us has had experience of the effect which it has had on our professional and personal lives. Change will not stop, it will continue at an increasing rate and the questions we must answer are how do we prepare ourselves to meet the challenge of future change and how do we take advantage of the opportunities which it will bring? It is these questions which I wish to discuss in this address.

Jan 1, 1989

By James S. Browning, W. H. Eddy

Laboratory batch and small - scale continuous flotation tests were conducted on a ferruginous barite - fluorspar ore from near Sweetwater , Tenn . , to determine the feasibility of producing commercial - grade fluorspar and barite concentrates . The lignin sulfonate - sodium fluoride - fatty acid method of floating fluorspar produced acid - grade concentrates . Flotation of the barite from the fluorspar tailing using petroleum sulfonate yielded concentrates suitable for use as a weighting agent in oil -well drilling muds . The continuous flotation tests , treating about 150 pounds of ore per hour , yielded fluorspar concentrates that assayed 98.3 percent CaF2 and barite concentrates that assayed 91.2 percent BaSO4 . The recovery of the two minerals was 91.2 and 85.2 percent , respectively .

Jan 1, 1964

By Emanuelle Garcia Reis, Gustavo de Sousa, Rodney Pardo Alves

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. In general, national and international plate markets are every day more rigorous about final product quality. Suppliers must be aware about dimensional accuracy, surface quality and flatness of the plates, independent of the quality standards. To guarantee the best service to this increasingly demanding and competitive market, it is extremely important to guarantee the original project conditions executing the right maintenance of the rolling mill main components. In order to maintain the product quality and avoid the production and maintenance cost increase, it is important to find ways to control the mill and the main process variables, through daily measurements of the equipment performance. This paper aims to present the influence of the main equipment variables that affect the mill operational stability and how to control and evaluate the mill performance.

Oct 1, 2019

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By Alicia E. Ares, Carlos E. Schvezov

In the present work it was observed the nucleation and growth of grains in the equiaxed zone of metal matrix composites (MMCs) samples directionally solidified wit the presence of columnarto- equiaxed transition (CET) in the samples. In order to do so, first, it was defined the difference between the real temperature at a given instant, which it is used in the analysis, its variation and furthermore, the variation in the solid fraction with time between the beginning and the end of solidification. It was determined a growth law assuming a lineal variation of equiaxed grain radius as a function of time, and also, it was expressed a law of grain density as a function of time, considering the presence of SiC and Al2O3 particles in the matrix. Finally, the results obtained were validated with measured values of grain density at each position of the thermocouples in the equiaxed zone of the solidified samples.

Jan 1, 2015

By Liang Wang, Sheng-Kai An, Bing Xie, Hong-Yi Li, Cui Li

In order to develop an environment-friendly method for extracting vanadium effectively from aqueous solution containing vanadium, the dynamic adsorption behavior of V by a continuous fixed-bed column which was filled with macro-porous weak base anion exchange resin was studied. Effects of conditions including the bed depth, flow rate, concentration of vanadium ions on dynamic V adsorption were investigated. The optimum adsorption conditions were established at flow rate of 6 ml/min with bed depth of 20 cm. Isotherms studies demonstrated that the column adsorption of V was a favorable chemical ion exchange process in monolayer. Several kinetic models were applied to analyze the adsorption characteristics. Analysis results of the Bohart-Adams model indicated that the adsorption process was dominated by external mass transfer in the initial stage. The Thomas model was appropriate to describe the column behavior, revealing that both external and internal diffusions were involved in the limiting steps.

Jan 1, 2014

By Danilo Gonçalves de Oliveira, Rogério Martins Pereira

Chatter is a widely studied vibration phenomenon that affects most cold mills around the world and its impact on these lines are tremendous: from productivity and quality losses to mechanical equipment damage. The investigation of its origins and how to minimize the occurrences and their impact on the equipment require special instrumentation and algorithms in order to have a detection of the vibrations as soon as they start. This paper presents three methods of identification of chatter on a Tandem Cold Mill and the actions to leave the vibration frequency range before its amplitude achieve catastrophic values.

Oct 1, 2019

By Guy Reed, Russell Frith

In situ or pre-mining horizontal stresses are arguably the least well understood of the principal inputs into underground coal mining geotechnical engineering design, whether analytical, empirical, or numerical. This is a direct result of both the cost and difficulty of obtaining meaningful stress measurements, the various limitations of the measurement method in terms of sourcing strata types that approximate the assumed conditions of the post-measurement mathematics to convert measured strains into stresses, and a common practice by some geotechnical professionals to preferentially utilise generic values rather than interrogate the available measurement data for cause and effect relationships between horizontal stress magnitudes, directions and a range of associated controls. That numerical modelling simulations attempt to mimic reality but often rely on simplified generic horizontal stress input assumptions is a particular cause for further consideratio The paper attempts to further explore the nature of in situ horizontal stresses using a range of stress measurement results from the Australian coal sector supplemented by several international studies addressing the same basic issue, the result being a number of credible and highly relevant “cause and effect" inter-relationships between the three principal in situ stresses in addition to the influence of rock properties (e. Young's Modulus and Poisson's Ratio), cover depth and the larger-scale structural geological environment. In particular, the paper demonstrates that despite being commonly overlooked as a primary rock/coal material property, Poisson's Ratio and the associated K Effect are intrinsic to understanding 3D in situ stress measurement results and therefore, predicting in situ stress magni- tudes more generally for geotechnical analyses purposes. As a fundamental question, the paper addresses whether it is necessary and of engineering value to characterise in situ horizontal stresses: according to distinct "domains," in the same way that more easily identifiable geotechnical properties such as rock mass ratings, coal seam thickness, ply splits, and cover depth are often treated.

Jun 25, 2024

By Wieda Azani, Alexander Tarigan, Willem de Beer

In block caving, the rates and sequencing of undercut production blasting, drawbell blasting, and mucking are the key levers for attempting to manage cave performance. Cave performance encompasses a range of factors, which include growth, shape and the effect of the cave on the abutments, excavations, geological structures and lithology. We compare production data in several panels in the Grasberg DMLZ and GBC block caves with the seismic response in work areas, around geological structures, and in geotechnical domains. These comparisons enable evidence-based conceptualising of the effect of production rates and mining layouts. By also considering the correlation of seismic release rates in different parts of the rock mass, the wider influence of a cave can be gauged through considering possible stress and / or deformation transfer. This concept is not novel, but it is rarely implemented in a routine fashion, principally because production data rarely are easily available. Previously, it has also been used to retrospectively compare seismic hazard between different mines. This paper discusses practical, day-to-day tools to manage seismic response to mining. Therefore, the paper presents a methodology for presenting seismic release and production rates on integrated plots at any time to facilitate quick identification of correlated spatial regions. This methodology explores the production data collection and geolocation at Grasberg, which will be described in some detail.

Apr 26, 2022

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022

By J. -E. Eriksson, L. Hupa, T. Khazraie

With increased co-firing of coal and different biomasses in power plants, there is a growing need to study and characterize the produced, often heterogeneous ashes and to assess their utilization as secondary raw materials. In this work, we compare different methods for characterizing the ash compositions. These methods include scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDS), X-ray fluorescence (XRF) and inductively coupled plasma emission spectroscopy (ICP-OES). The content of carbonaceous residues in the ashes was measured with CHN Sanalyzer. The methods and the pretreatment required for each of the analysis were studied in detail for three ashes: (1) coal, (2) peat and wood, (3) peat and wood residue with dolomite addition. The limitations of each method will be discussed. This work gives guidelines for selecting a rapid and reliable method for analyzing the suitability of the ash for a particular application.

Mar 1, 2018

By Yun Guo, Min-Min Lin, Bing Xie, Hong-Yi Li

The extraction of vanadium from vanadium-containing APV-precipitated wastewater by W/O microemulsion system was studied. In the N263/n-heptane/isoamyl alcohol/NaCl microemulsion system, N263 played double functions of cationic surfactant and extractant to form microemulsion in n-heptane, and isoamyl alcohol was added in the microemulsion as a cosurfactant. The extraction of vanadium by W/O microemulsion systems effectively accelerated the extraction and improved the extractatability because of the enormous increase in the micro-interfacial surface area. Due to ion association with extractant, vanadium was extracted into the microemulsion phase. The influence of different parameters on the extraction ratio (E%) were investigated, including the volume ratio of aqueous phase to microemulsion, surfactant concentration, pH value of the feed solutions, cosurfactant concentration, extraction time as well as temperature. In optimum conditions, the extraction ratio (E%) can reach 97.2%.

Mar 1, 2018

By Jian Pan, Deqing Zhu, Benjing Shi, Yuxiao Xue

COREX smelting reduction process which is freed of metallurgical coke provides a sustainable developing way for ironmaking industry. However, the shortage and high cost of pellets limit its development in China. Meanwhile, iron ore sinter has a great output in China. This work studied the reduction behaviors of sinter made from magnetite concentrates during the reducing process of COREX shaft furnace and compared the RI and RDI of sinter with BF process. The results showed that the reduction degree of sinter increased obviously during the temperature zone from 600 to 850 °C, while the reduction degradation presented rapidly aggravate in the temperature zone from 425 to 550 °C in COREX shaft furnace, and the increase of metallic iron content leads to the degradation of sinter got decreased slightly during the stage of temperature above 650 °C. Sinter got higher RI than BFprocess but also got higher RDI in low reduction temperature of 550 °C, which means sinter would have heavier disintegration in COREX shaft furnace.

Mar 1, 2017

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988