Search Documents

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By Neil Campbell

Abstract Following discovery on the Giant property of very promising gold deposits, some of which terminate against the steeply-dipping West Bay fault, a geological study was initiated co locate possible faulted extensions of the ore. Geological mapping revealed that the ore and the shear zones to which the ore is confined are older than the fault and therefore subject co displacement by it. It also disclosed several diabase dykes which seem co provide the best basis for determining the fault movement. After applying various techniques co determine their strikes and dips, the dykes were used as structural markers and it was estimated that, subject co certain possible errors, the movement on the fault was 16,140 feet (3.06 miles) south and 1,570 feet (0.297 miles) down on the west side relative co the ease. Evidence supporting this conclusion was obtained when subsequent deep diamond-drill holes intended to test the hypothesis cut an ore-bearing major shear zone which, so far as can be determined, is nearly identical with its present correlative on the Giant property. Introduction The fault under consideration follows a northerly trend past the west side of the original settlement of Yellowknife, which is situated 600 miles north of Edmonton and 400 miles from the Northern Alberta Railway terminus at Waterways, Alberta. The mining properties chiefly concerned include the southern part of the Giant claims, on the east side of the fault, and the Con-Rycon-Demelt claims, on the west side, 3Y2 miles to the south. Geological data were also obtained from the eastern part of the A. Y.E. property, which lies south of the Giant claims, and from the Negus, Meg, Yellorex, and Kam properties, which are south and southeast of the Con-Rycon-Demelt claims. Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault which appears to be the greatest, resulted from the work of Dr. A. W. Jolliffe (McGill University, formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply-dipping dislocations of the earth's crust. In the winter of 1939, a mineralized shear zone named the Creek Vein was found on the Giant property. It was noticed that the space relationship between the new shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acidic flows lying north of the Con property. Coupling this relation with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear.

Jan 1, 1947

By E J. Cowan

Efficiency demands that mine geologists devote the most time to tasks where they can have the biggest effect on production. One of the most time-consuming tasks is geological interpretation of the orebody and turning this into a block model for the planning engineers.The current best practice for mines that require a geologically constrained resource model involves capturing the interpretation of geologists as three-dimensional (3D) wireframes. However, there is significant overhead in the production of valid wireframes from sectional and plan interpretations. This overhead consists of the mundane tasks of digitising polylines, then building 3D wireframes and validating them. While software can simplify this task, the current process is not the best use of a geologist’s time. Under time pressure exerted by planning engineers and the time required for modelling from polylines, geologists are forced to roll-up the presence of other elements or impurities into the interpretation and encode them in the polylines, even though it is often desirable to consider these other factors separately.While it might seem unlikely that mine geologists can produce constrained geological models without the intermediary of wireframes, the technology to accomplish this is getting closer.In this paper, the results of a trial at the Savage River magnetite mine, which is owned and operated by Grange Resources Ltd, are reported. The trial was for a ‘direct-to-block’ implicit geological modelling method. The focus was on creating a geological attributed block model from drill hole geological log data; resource estimates were not determined. The categories modelled were air, waste, low-grade ore, medium-grade ore, and high-grade ore. The block model outputs either resulted in a proportional block model (categories expressed as percentages within equivolumetric blocks) or a sub-blocked model (parent block and one sub-block), which is the preferred block model output at the Savage River mine. When compared to the traditional best practice modelling method, which takes 43 work days, the wireframe-free modelling method took only 26 hours from initial modelling, using both exploration and grade control data. An update using appended drill hole data is achievable within one day. These results represent time savings of more than one order of magnitude compared to the traditional workflow, and, as such, these figures merit serious consideration for the use of the direct-to-block modelling approach at other operations.With these time savings, geological and estimation models can be kept updated constantly; geologists will not need to set aside two months for quarterly or half-yearly modelling of the drill hole data for resource review. Such dramatic time savings will allow for the better use of highly skilled geologists, who are in short supply in the current market, and will also impact directly on downstream mining engineering workflows.

Aug 22, 2011

"Chairman: Dr R. E. ROBINSON Rapporteur: Dr R. P. COLBORNPapers:The simulation of crushing plants by W. J. WhitenSimulation of multi-component flotation plants by B. K. Loveday and G. R. MarchantComputer control of flotation at the Ecstall concentrator by M. P. Amsden C. Chapman and M. G. ReadingModel for the design and control of flotation plants by R. P. KingIn presenting his paper Dr W. J. Whiten outlined the basic concepts on which the control model was based and emphasized the fact that empirical models based as much as possible on theory were used to simulate each unit of the crushing plant. The final parameters of each model were computed using data collected from the plant. Unfortunately, the system did not permit accurate extrapolation but was successful when operating in the region from which the parameters were calculated.He concluded from the results of the test work that the crusher amperage was a critical parameter and that the utilization of the model gave a 15 per cent increase in the plant output. This was because the model predicted that a marginally fine grind would provide a significant increase in throughput. Dr Whiten elaborated on what constituted the multiple spline regression, explaining that it was a least-squares curve-fitting technique in one or more dimensions, where the calculation of coefficients in analytic expressions was replaced by the calculation of typical points on a very smooth curve called a spline function. The emphasis was placed on the shape and value of the curve or curves instead of on the coefficients as in analytic regression. A spline function was the line drawn between all points constituting the data set.Dr B. K. Loveday commented that the simulation was unusual in that the optimum throughput was considered to be the maximum throughput, which, surely, was limited by the crusher size. He also emphasized the importance of the interaction between both crushing and grinding circuits and added that in practice the optimum operating conditions were inter-dependent. Dr Whiten replied that in the case of the plant under consideration, the crushing process was not, in fact, the limiting operation.Mr C. E. Clifford indicated that the model was being used to simulate a number of crushing and grinding circuits at Mount Isa Mines. He reported that the model simulated the circuit satisfactorily for primary and secondary gap settings of 0,625 in. to 0,375 in., but that adjustment had to be made to the model parameters for gap settings of 0,250 in. to 0,125 in.In reply to a question from Dr D. M. Hawkins, Dr Whiten said that he preferred to use low-order splines with smaller segments rather than high-order spline functions with large segments."

Jan 1, 2014

By Alena Johnson

"Much of the copper being produced today uses heap leaching, where pure metal is extracted from the ore with a chemical process rather than smelting. This technique is deployed extensively in major copper producing areas including Chile, Peru and the southwestern United States.Copper ore is excavated from the ground, crushed and then spread in uniform layers on a pad. A slow trickle of sulfuric acid is distributed over the pile, where it percolates to the bottom and a collection point. The acid leaches out the copper, along with other minerals, which can be extracted chemically. This process can be used at large sites producing 100 kt/a (110,000 stpy) and greater.Production on a massive scaleProduction at heap-leach sites is continuous and can operate on an enormous scale. The ore is fed into a crusher to break down the large pieces, and then it moves into an agglomerator to capture the fines and create more uniform particles. While in the agglomerator, the ore is mixed with acid for the first time, helping it to bind the fines into larger particles and starting the leaching process. The treated ore moves by conveyors to a stacker designed to spread it uniformly on the pad.The size of the operation comes into perspective by considering a typical pad measures 1.6-km (1-mile) long and 0.8-km (0.5-miles) wide. Working day after day, the stacker creates individual piles or modules on the pad, each 122 x 61 m (400 by 200 ft) and 3 m (10 ft) deep. When one module is filled, it moves across the pad to the next, filling the area in one continuous pile. A completed row of modules spanning the width of the pad is a cell. Once the entire pad is covered, the process begins again laying down another 3-m (10-ft) layer, and it continues until the entire pad reaches its height limit which can be several hundred feet.Once a new module is completed, technicians lay a network of plastic pipes over the surface in a pattern similar to agricultural drip irrigation installations. The diluted sulfuric acid, called raffinate, is pumped through the pipes so it can be distributed over the module, allowing the acid to soak through the ore and leach out copper as it percolates to the bottom. At the same time, approximately 35 to 45 percent of the acid is consumed by dissolving the calcite carrying the metal in the process. The raffinate reaching the bottom is now characterized as pregnant-leach solution (PLS) since it carries the copper the company is seeking to recover."

Jan 10, 2018

By John R. Reigart

The Tri-State district, as its name indicates, is composed of portions of three States, the southeastern corner of Kansas, the northeastern corner of Oklahoma, and an adjacent strip of Missouri east of these portions of Kansas and Oklahoma. An area approximately 40 miles long in a northeasterly-southwesterly direction, and 30 miles wide at right angles thereto, containing minable occurrences of ore at widely scattered locations, comprises the district. However, what has been and is the main productive area, is a strip about 35 miles long and 10 miles wide, which begins at Miami, Okla., as its southern extremity and runs in a northeasterly direction through Commerce, Picher, and Hockerville, Okla., Baxter Springs and Galena, Kans., and Joplin, Webb City-Carterville and Carthage, Mo. Almost the entire present production comes from the area between Commerce and Baxter Springs.

Jan 1, 1932

By V. F. Parry

The object of this report is to present certain pertinent data on the physical and chemical properties of South Arcot lignite and to present the results of several special tests to show how the raw lignite can be upgraded to superior fuels for certain special uses. The Bureau of Mines Branch of Coal Technology laboratories at Denver have advocated the drying and carbonization of all low-rank fuels for special uses and have introduced and developed new techniques for upgrading and refining noncoking coals. Application of these techniques to the South Arcot lignites was the object of the investigation, and this report presents significant data necessary for planning a fuel program based on utilization of dried and carbonized dusts. In general, the South Arcot lignite is similar in chemical properties to the high-moisture lignites found in the United States and has some physical properties similar to Australian brown coals. The samples submitted for test had lost moisture before delivery to the laboratory, and it has been necessary to estimate the analysis of the lignite in place in the mine. Various observations made in India by qualified technicians indicate that the bed moisture content of the entire seam is in the range of 54 to 56 percent. For estimating purposes in this report, the bed moisture content has been taken as 56 percent and the ash content of the fresh coal as 2.5 percent. The average analysis estimated for the as-mined lignite is: [Moisture percent 56.0 Volatile matter do.22.0 Fixed carbon do.19.5 Ash do.2.5 Heating value B.t.u. per lb. 4,890]

Jan 1, 1957

By Y. Okahara

The chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganeus oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were difficult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexitites of the reactions, and the possible mechanisms were discussed. Then three manganiferous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides.

Jan 1, 1969

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By Edgar Peek

"The two dominant metallurgical problems in treating most base metal sulphide concentrates in both the chloride and sulphate system are iron removal and sulphur elimination, respectively [1-3]. In this paper the opportunities, limitations and fundamentals of the chloride metallurgy system are described against this background. Only the treatment of oxide and sulphide ores is considered. Both hydrometallurgical and pyrometallurgical unit process operations are highlighted, since most successful base metal processes are based on a combination of the two. Hence, an overview of the technical and also some economical aspects of chloride metallurgy are presented.This overview summarizes the successful applications of chloride metallurgy, but it will not give exhaustive process and plant descriptions. It predominantly focuses on the essential technical features of the metallurgical unit process operations, while providing numerous references separately."

Jan 1, 2011

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1981 (October 1, 1980 - September 30, 1981) under its Minerals Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

By John Carr

The tremendous growth in grinding mill size and horsepower during the '70s demanded advancements in gear cutting technology and equipment for the '80s. Computers are used as an aid in the design and selection of the mill drive system; sophisticated computer graphics are used to create manufacturing drawings; and a new generation of gear cutting machines are used to manufacture the gears. These new gear cutters can generate-cut gears over 40' (12.2 m) in diameter at an AGMA quality level exceeding the currenty acceptable standards. The precision of the resulting gear assures maximum tooth contact, which will result in longer gear set life.

Jan 1, 1981

By R. E. McIvor, Brian Cornish, J. A. Finch, Yue Tan, Claude Gagnon

Fred C. Bond is recognized throughout the mineral processing world as the father of comminution equipment applied science and engineering. The Bond Work Index became a universal standard, and is the most widely used measurement tool for comminution energy consumption. This biography is the story of his lifetime of study, work experiences, experimentation, analyses and findings. His numerous published writings are reviewed. His legacy is one of comminution process engineering that will be used in perpetuity.

Feb 1, 2024

By C. A. Meissner

THE following is a further discussion of the paper of James Gayley, " The Application of Dry-Air Blast to the Manufacture of Iron " (Trans., xxxv., 746), with special reference to his sup-plementary paper (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 797 to 819), and. to the paper of J. E. Johnson, Jr., "Notes on the Physical Action of the Blast Furnace " (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1111 to 1146). Mr. Gayley's paper has been discussed also by E. Windsor Richards, R. W. Raymond, E. H. Saniter, W. J. Foster, H. M. Howe, V. Pendred, B. H. Thwaite, James Gayley and Alexander Pourcel (Trans., xxxv., pp. 1022 to 1042), Joseph W. Richards (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 703 to 718); T. W. Robinson (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 788 to 796) ; C. B. Dudley, R. W. Raymond, J. E. Johnson, Jr., W. F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1147 to 1152);.E. de Mille Campbell (Bi-Monthly Bulletin., No. 1, January, 1906, pp. 25 to 50) ; John Birkinbine (Bi-Monthly Bulletin, No. 1, January, 1906, pp. 137, 138). At the Washington meeting of the Institute, May, 1905, a very instructive and interesting paper was presented by Mr. J. E. Johnson, Jr., entitled " Notes on the Physical Action of the Blast Furnace,"' in which reference is made to Mr. Gayley's dry-blast process. A few of Mr. Johnson's conclusions, as summarized in the last pages of his paper, do not appear to me to be in complete accordance with the results obtained at the Isabella furnaces; and I therefore present the following notes which may throw further light on this subject: Mr. Gayley has called attention to the fact that the moisture in the air is an extremely variable and uncertain factor; and

May 1, 1906

By Alfred L. Ransome

The consumption of slab zinc in the United States increased sevenfold in less than a half century since 1900. Therein is reflected the innate characteristics of this versatile and nearly indispensable nonferrous metal whose use has grown at more than twice the rate of industrial production. The total metal consumption was substantially stimulated during the two World War periods, which were likewise marked by notable changes in use pattern accompanied by shifts in geographic distribution. This information circular summarizes basic data collected for many years by the Bureau of Mines, but in particular presents for the 1940-45 period details derived from the comprehensive slab zinc consumption survey inaugurated in 1940. The total consumption of slab zinc has been broken down into four major categories galvanizing, brass products, rolled zinc, and zinc-base alloys -- with minor applications grouped under a fifth heading, other uses. Ex- cept for the inclusion of zinc-base alloys with other uses before 1926, the above-named segregation has been shown for the entire period 1900-45. 11- though a substantial tonnage was taken by all groups in all years, there were large shifts in the use pattern in both World War periods. In both, the Allied Powers depended heavily on the United States for zinc-bearing products, especially those required by war industrius. The departures from usual uses were, however, much more marked during the second than in the first period, mainly because the United States could not have met the tro- mendously expanded war-materiel demands had the greater slab zinc needs of a period of high industrial activity been supplied. The geography of consumption is known in detail only for 1940-45. Even in that short period, substantial shifts are observable, largely the reaction from conversion to war production in 1940-41 and reconversion to peacetime consumption in 1945. However, there is so evidence of other shifts in consumption centers that appear to reflect longer-term develop- ments.

Feb 1, 1948

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By HUNTINGTON ADANS

(Wilkes-Barre Meeting, June, 1911.) THE arrangement of a flow of cyanide-pulp through Pachuca tanks in agitation, so as to permit a continuous process, instead of alternate filling, agitation, and emptying, has been proposed by various writers within the last two years, and more particularly by A. T. Grothe, agent for the Brown patents on Pachuca tanks in Mexico. It was first put into practice, I believe, by M. H. Kuryla at the Esperanza mine in El Oro, Mexico. The starting of agitation in Pachuca tanks after filling may offer no serious difficulties with ores which do not settle rapidly in such tall tanks; and the adaptation of the tanks to continuous agitation under such conditions may give simply a somewhat more convenient method of treatment and greater agitation-capacity for a given number of tanks, because of the saving -of time lost in filling and discharging. But in the treatment .of pulp which tends to settle rapidly, as in the cyaniding of concentrates or of the whole pulp of ores containing heavy sulphides, the packing of the slime at the bottom may, cause much trouble. The use of the radial air-pipe attachments near the top of the cone and of the air-valve outside of the air-lift .tube at the bottom may obviate the difficulty to some extent; but the action of the radial air-pipes on the cone-sides is that -of a sand-blast, and their continuous use cuts through the tanks. Moreover, even when these pipes are used, some pulps will pack tightly below them in the cones. Under such conditions the use of Pachuca tanks with intermittent filling and discharging becomes a troublesome process. Time is lost in ,starting agitation; large quantities of compressed air are wasted; pulp is blown over the tank-tops; and not infrequently it may be necessary to dig out the bottoms of tanks by hand. This trouble is the only important one occurring in the use of Pachuca tanks; and, since it is caused by intermittent filling, the .arrangement of a continuous flow of pulp from tank to tank,

Aug 1, 1911