Search Documents

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By Neal Lee

Reduced relief horizontally means an increase in energy expended vertically into the rock surrounding the stemming column, and potentially through the stemming column. The vast majority of holes in any surface blasting operation are afforded two horizontal relief faces at the moment of firing, whether by existing relief faces in front of and to one side, or previously blasted hole(s) in front of and to one side of the holes in question. When the energy expended in any hole on the blast pattern has less than two Horizontal Relief Planes or faces (referred to moving forward here as “HRPs”) available to it at the moment of firing, a higher percentage of the available energy is directed vertically. In the analysis of recorded videos by the author, one will note the fact that stemming ejection/flyrock is observed to a much greater degree from the center of almost all patterns when they are timed to “pull out of the middle” (“box cut" timed patterns). This is because the first hole to fire in each row has only one Horizontal Relief Plane, which significantly decreases horizontal avenue for energy release for these holes. This of course results in an increase in the amount of energy expended vertically. This paper proposes a novel methodology to modify the stemming to better use the explosives energy of each hole, while controlling side effects such as flyrock and airblast.

Feb 6, 2023

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018

By D. C. DERINGER

METALLURGISTS and mill operators appreciate, in a general way, .the economic or commercial relationship between recovery and grade of product but few have correlated in detail fluctuating metal prices with the metallurgy. They know that many factors such as metal price, dedusiions for returning charge, transportation, percentage of metal in head ore, etc.; all affect the commercial relationship between recovery and grade of product. In practically every mill some one at some ' time has calculated the amount of recovery that can be sacrificed for each percentage increase in grade of concentrate and from this calculated ratio the commercial or ., economic tail has been established. Such a ratio finally becomes a well-entrenched rule by which the progress of the metallurgy is judged.. When once established, these-, ratios are but seldom corrected to changes of metal prices for each possible grade of concentrate that may be produced. The calculation is tedious when often repeated. Other methods have been suggested and used to correlate the commercial with the metallurgical phase. A factor .derived ,by multiplying the grade of concentrate by recovery is often used, but is of little importance because it does not possess a single commercial quantity. The percentage monetary recovery calculated by dividing the gross value of the ore into the net smelter return gives a good economic index and, is to be commended, but it is difficult to correlate exactly and quickly the work of each day on a commercial basis.

Jan 1, 1931

By Aleksandar D. Bugarski

Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element. The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems.

Jan 1, 2009

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By H. C. Hamontre

The liquid-level gage described in this report is an instrument designed to locate liquid levels in wells rapidly and accurately and, with auxiliary equipment described, to follow moving liquid levels automatically. The depth at which the instrument makes contact with the liquid in a well is indicated at the surface by a depth meter on the cable to which the instrument is attached. When the gage is used to follow a surging moving level, the liquid depth is indicated continuously at the surface. This report contains a description and illustrations of the gage and outlines the operating procedures. The instrument is 1-3/4 inches in diameter and approximately 6 feet in length and may be operated through 2-inch tubing. The gage consists essentially of a float that moves upward with respect to the rest of the assembly, causing a change in the flow of electric current from the surface when the liquid level is reached. The instrument has been tested under a variety of conditions and has been found to be sensitive to changes in liquid level of 1/2 inch. Its accuracy is limited principally by the accuracy of the wire-line depth indicator used. It is not affected by pressure or temperature, and it can be run in open hole or under pressure through a lubricator. It employs only one electric circuit and can be run on an Amergraph single-conductor cable (type 1-H-0) ,

Jan 1, 1954

By D. W. R. Haysom

"I AM CONSCIOUS of the honour you pay me by having invited me to address you on the subject of the Rehabilitation of the Sydney Steel Corporation. The true architect of the revival and rehabilitation is Robert Burns Cameron. Because of the numerous myths which have grown up around what seems to be the miracle of the revival of the Sydney Steelworks, I propose to go back to the time when they came under the full control of the Province, on the 1st of January, 1968. Late in 1967, the decision was taken by Premier G. I. Smith to keep the Steel Plant running for at least another year, in an endeavour to see whether the enormous losses being sustained by Dosco could be reduced to a level which would permit their continuing operation. When that decision was taken, Dosco was to continue management until the 30th of April, 1968, and in the intervening period, the Provincial Government would seek management of the right calibre to ensure that an objective view of the Steelworks operations could be secured. By a combination of circumstances which can only be described as most felicitous, the man selected for the task was R. B. Cameron. He very quickly determined that to permit Dosco to continue management of the Steelworks until April 30 could only result in heavy losses to the Province and a consequent deterioration in the already critical financial position and a declining morale of the worke"

Jan 1, 1972

By Gary Cavanough

The spontaneous exothermic reaction of ammonium nitrate explosives with sulphide-containing rocks, commonly referred to as reactive ground, is a site-specific condition that can lead to spontaneous detonations. Mine sites typically carry out regular assessment of ground for reactivity. In Australia, reactive ground testing is conducted according to the Australasian Explosives Industry Safety Group (AEISG) Code of Practice. This paper presents a new method to assess reactive ground. The new method can be completed on the mine site or in the laboratory. The new method allows samples to be tested in hours not weeks, as required when using the method prescribed in the AEISG Code of Practice. The new method also provides an explanation of why ground is reactive or not reactive, Whereas the AEISG Code of Practice provides a reactive, not reactive or marginal results with no understanding of reason for these results. Case studies on the use of weathering agents, pH, sulphide content and carbonate content will be reported. These case studies identify instances where the testing as per the AEISG Code of Practice provides false positive and false negative results. A false positive result will require the use of inhibited products when they are not actually required which increases costs and reduces productivity due to the need to used multiple explosive products. A false negative result increases the risk of an unplanned initiation of a blast hole.

Feb 6, 2023

One of the earliest and continuing challenges in driving sustainable development in large scale resource industry projects is around the issue of assessment û how do you measure the sustainability of a mineral operation? One of the key road blocks when confronted with this challenge is the temptation of technical folks to reach for a definition of sustainability or sustainable development. But definitions, by definition, have boundaries and limitations that serve to constrain thinking û they limit the thinking of what we can achieve with sustainability (it also acts as a barrier that constrains innovation). Rather than seeking definitions, better understanding of the core perspectives around sustainability and their application to the minerals industry provides a much more powerful platform from which to conduct assessments. But it is only when these perspectives are combined with the right framework and supporting techniques that the complex becomes doable. With the support of the perspectives and the framework, various assessment and measurement methodologies can be used; the challenge is communicating to stakeholders the sustainability character of the project in ways that are meaningful and to which people can connect. Assessment is not about finding the best or most accurate methods that fulfil strictly academic and possibly abstract requirements. The challenge is to help people understand what the impacts are, and what the value contributions will be, in a format and language that make sense in their world-view.

Jan 1, 2009

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By J. Pelders, F. Magweregwede, S. M. Rupprecht

Increased depths of conventional gold and platinum mines, longer travelling times as working places move further from the shaft, and ancillary activities taking place in the mining cycle reduce the useable time spent at them workface. Current shift lengths of 8 hours 20 minutes may no longer be adequate ton complete required mining activities.The impact of mineworker commuting times on shift work is also not well understood. The aim of this research was to draft a framework to optimize shift cycles in order to maximize productivity, health, safety, and wellness in the South African mining sector. The framework was informed by a review of the literature, case studies at a local gold mine and platinum mine, and a workshop with industry experts. The findings indicate potential advantages of extended shift lengths and continuous operations, such as improved productivity, asset utilization, and employee morale. However, concerns included fatigue and the associated safety hazards, particularly when working longer shifts, night shifts, and numerous consecutive shifts. Job demands, personal factors, and commuting times are further considerations when scheduling shifts. The ideal shift system for the mining sector should holistically consider and balance operational requirements, health and safety, and employees’ and their families’ requirements, and suit the unique needs of each operation. Changes in shift cycles will require a structured change management process, which involves all stakeholders, and could help to enhance the viability of the South African mining sector.

Aug 1, 2021

By D. Jacobson

There are many different machine design parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the speed at which the cone gyrates. In June 2012, pilot tests were conducted to determine the production and operating conditions over a wide spectrum of speeds. mining operations will have variations in the ore characteristics and feed rates that result in non optimal use of the crushing energy and inconsistent process control. This study documents the measured variation in production and energy efficiency with two operating modes. Overall, the results match the theory, and the capacity and power fluctuated by 25% and 17%, respectively, when operated at full capacity, with an overall trend of slightly coarser discharge size distribution as the speed decreased. Using a fixed feed rate, the crushers had 4-14% higher production when operating at the optimal speed. Secondary analysis showed that the power draw consistency and magnitude of power spikes could also be improved by optimizing the cone speed. Varying the speed of the crusher can be used to tune the crusher during commissioning, adapt to changing ore conditions over long periods of time or be used as a dynamic input into an advanced control system. each action above would serve to make the crusher(s) more productive, more energy efficient, impove process control and would also have mechanical benefits for the machine

Dec 1, 2013

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By B. W. Naugle

The Bureau of Mines investigated the changes that occur in decomposition products when coal is carbonized in a fluidized bed with steam as the fluidizing medium and the vapors are subsequently cracked without condensation in a fluidized bed of high-temperature coke. The coal used was from the High Splint bed, High Splint mine, Harlan County, Ky. Since this coal is agglomerating, it was blended with char. The integrated unit used in this investigation consisted of a 3-inch-diameter fluidized coal carbonizer, a 3.5-inch-diameter cracker containing a bed of high-temperature coke fluidized by the tar vapors and steam from the carbonizer, and gas-cleaning and product-recovery systems. The carbonizer was operated at 485° C and the cracker at 600°, 700°, and 800° C. The process variables investigated were temperature, residence time, and concentration (pound of tar vapors per pound of steam to the cracker) of tar vapors in the cracker. The total tar yields decreased as the temperature of the cracker increased, and at a constant cracker temperature of 600° C the yield of paraffins, acids, aromatics, and olefins in the distillate increased directly with the tar vapor concentration in the cracker. At 700° and 800° C only the acids and aromatics increased with increased concentration. Bases remained essentially constant regardless of the temperature and concentration. Similar results were obtained when the tar from the carbonizer was condensed prior to feeding to the cracker.

Jan 1, 1965

By James M. Stuckey

In a search for improved methods of upgrading tar obtained by low-temperature carbonization of coal, monoethanolamine (MEA) was found to be effective in extracting tar acids from coal tar distillates derived from a subbitunwous and a lignite coal. Patch extractions showed that both yield and purity of the extracted acids improved with increasing volume ratios of monoethanolamine to tar acid, varied from 1:4 to 8:1. Yield improved, but purity decreased as the concentration of monoethanolamine was changed from 30 to 70 volume-percent, and as the concentration of tar acid in distillate was increased ad from 14 to 45 percent. In a continuous countercurrent extraction employing a double solvent (monoethanolamine and hexane) approximately 80 percent of the tar acids was extracted from 170° to 350° C. tar distillate when using 1.6:1 volume ratios of amine:tar acids. Tar acids isolated from his extract, although of improved purity, contained appreciable quantities of neutral oils and some tar bases. Aqueous monoethanolamine was not effective for extracting the last 10 to 15 percent of tar acids in 170° to 350° C. distillate oil from lignite coal. The highest yield of isolated tar acids and the best recovery of monoethanolamine were obtained by diluting the extract with water and saturating with C02. Some losses of solvent were encountered when aqueous monoethanolamine solutions were heated through decomposition of the amine with the liberation of ammonia.

Jan 1, 1960

By A. Yörükoglu

In this study, thorium mineral that found in the complex ore deposit bearing bastnasite, fluorite, and barite from Eskisehir - Sivrihisar district has been tried to extract by using HCl and H2SO4 leaching. Ore sample of approximately 3 tons taken from the ore deposit has been homogenized in order to obtain composite samples by means of ore preparation techniques for experiments. Results of chemical analyses of composite samples are as given; 40.8% CaF2, 35.35% BaSO4, 2.01 Ce, 1.5% La, 0.39% and 0.1% Th. HCl and H2SO4 leaching processes have been performed to gain Th in the ore. For determining the optimum particle size, the samples have been ground under controlled conditions and brought to the sizes of 0.065, 0.2, 1 and 3 mm. Leaching experiments have been carried out in both HCl and H2SO4 acids without roasting and roasting at the temperature of 900°C for 1, 3 and 6 h retention times for all particle sizes determined before. In the experiments, the highest Th recoveries reached are as follows; 78.74% Th when H2SO4 and 1 mm particle sized sample used, and 1 h roasting applied and 73.38% Th when HCl and 1 mm particle sized sample used, and 3 h roasting applied. Keywords: thorium, leaching, concentration, sivrihisar, roasting

Sep 1, 2012