Search Documents

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By G. White

Traditional atmospheres used for Aluminum annealing have been air, exothermic gas, and cryogenic purity Nitrogen. Air and exothermic gas have several problems associated with them such as surface discoloration, toxic emissions, and explosion hazards. High Oxygen levels can cause Magnesium streaking and oil staining, and therefore pure Nitrogen has been the atmosphere of choice for high quality Aluminum coils. A comparative study was made on key Aluminum alloys annealed in Nitrogen with different Oxygen concentrations to determine the effect on surface quality. The atmosphere composition inside the furnace was analyzed during the purge and heat cycle to determine its effects on purge times and exhaust emissions. The Aluminum coils after annealing were visually inspected for surface staining before and after rolling. The lab study revealed that Nitrogen with up to 1.0% Oxygen is acceptable, and did not adversely effects the surface quality or any of the other processing variables. However it isbelieved that higher Oxygen concentrations are acceptable depending on the rolling oils and alloy systems.

Jan 1, 1996

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996

"INTRODUCTION While the United States coal mining uses prescriptive regulation under the Title 30 Code of Federal Regulation enforced by the Mine Safety and Health Administration (MSHA), Australia uses a risk based approach. Australian regulation is individual to each state. In Queensland, Australia this risk based approach to address principal hazards is underwritten by the Queensland Coal Mining Safety and Health Act of 1999 and the Coal Mining Safety and Health Regulation of 2001. Each Queensland Mine is required to have an overarching Health Safety and Environment Management System, of which Safety Management Plans are an element. “Safety Management plans (SMP’s) are intended to formalise the process by which mines address principal hazards and other related matters to ensure the safety of mine personnel.”7 THE QUEENSLAND CONTEXT In Queensland, the basic elements of a coal mine’s safety and health management system must provide for risk identification and assessment, hazard analysis, hazard management and control, and the reporting and recording of relevant safety and health information and data.5 (Part 2 Division 1 Section 6(a-d)) The initial guidance for writing Safety Management Plans comes from the Approved Standard for Mine Safety Management Plans and Guidance Note QGN09- Reviewing the Effectiveness of Safety and Health Management Systems. The Guidance Note and Approved Standard are supplemental to the Act and Regulation, and put in place to provide more clarity around the topic. The definitions in this section come from the Approved Standard and are included to provide context for those who may not be familiar with Australian or Queensland law and regulation. A hazard is defined as a source of potential harm or a situation with a potential to cause loss, while a principal hazard is a hazard with a potential to cause multiple fatalities. A risk is the chance of something happening that will have an impact upon objectives which is measured in terms of consequences and likelihoods. It is important to be able to make the distinction between a hazard and a risk. For instance, a lion is a hazard, while the risk associated with a lion is getting eaten. As defined by the Queensland Approved Standard for Mine Safety Management Plans, a Safety Management Plan (SMP) requires a systematic definition of all the actions necessary to ensure that mining operations are carried out safely. A SMP includes, but is not limited to organisational structures, planning, activities, responsibilities, practices, risk identification, audits and reviews.7 The goal of a SMP management plans is to mitigate the risks to bring them to an As Low As Reasonably Achievable (ALARA) level."

Jan 1, 2016

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By A. Hasselbring

Sub-Level stoping was used in this country at least as early as 1912, at the Magpie mine in Michipicoten. The fundamental principles of the system are the same wherever it is used, but modifications have been adopted in the Michigan iron mines and in several Canadian mines. It is a system whereby a suitable body of ore may be developed quickly and worked cheaply, with a low initial expense, and by miners of quite ordinary ability. The basic method, described in the following pages, may be modified to meet conditions where one or more factors are not in accord with normal sub-level stoping requirements. In suitable ground, sub-level stoping is probably the most satisfactory method yet devised for underground hard-rock mining. It is so simple, straightforward, and safe that no special training of a crew is necessary. Any miner capable of drifting and raising can carry on the work necessary for sub-level stoping after the shaft has been sunk. The method is suitable, however, only for reasonably wide ore-bodies, the minimum width of ore to which it can be economically applied being somewhere in the neighbour-hood of thirty feet. The development programme is simple. Assuming, for purposes of illuslustration, an ideal ore-body, two thousand feet long, dipping nearly vertical, and varying in width from forty to a hundred feet, this programme would be as follows. The shaft should be sunk on the footwall side about sixty feet outside of the ore-body and near its centre. Levels are then established at suitable intervals, usually 125 feet. On each level, a cross-cut is run to the ore-body, and there a main-haulage drift is driven in either direction to the end of the ore. Cross-cuts are then run at 25-foot intervals, so that ore-chutes can be spaced about 25 feet centre to centre each way. It is not necessary that these cross-cuts be extended to the walls of the ore-body, if the position of the walls is known; they are extended just far enough to make room for the correct location of the chutes.

Jan 1, 1934

By Francois Clerf

IRON ORE fields are situated in both the East and West of France (see maps). The eastern deposit is by far the most important from a tonnage point of view, not only in France, but in all Europe. The ores of this region are known as minette, and are situated in the Lorraine ore fields and the Briey plateau. The iron ores of the West are those of Normandy, Anjou and Brittany. Before the war, a large number of important German companies had acquired considerable interests in these western fields and a heavy trade with Westphalia had begun. Recently, however, conditions have changed and some of the mines of Brittany and Anjou are now idle. From a geological point of view, in Anjou and Brittany, a series of synclines extends from the northwest to the southeast, containing a number of seams of varying thickness and generally intercalated in Silurian and sometimes in Devonian formations. The ore is generally a hematite or a magnetite. The composition varies from 48 to 52 per cent of iron and from 8 to 12 per cent of silica. Con¬servative estimates indicate a con¬siderable tonnage of workable ores (150,000,000 metric tons).

Jan 1, 1936

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

By John W. Buch

IN my review a year ago I pointed out that a small coal-mining companies as well as large had decided that the so called ?central shop? was a benefit. These central shops replaced in a large measure the commercial shops operated by those who have no direct connection with production of cod. Central shops in this time of salvage and major repairs have proved their worth. In addition, many of the larger companies had in their central shops equipment available for the production of many thousands of parts for our vast war machine and, as subcontractors, are doing this type of work. This is a real contribution to the war endeavor. Lack of new supplies has resulted in exhaustion of those stocks formerly stored or hidden in underground shanties. This means that the small stock of repair parts likely LO be available to any mine

Jan 1, 1943

By James Lorimer

THE topography at the Stan Trg mine facilitated early exploration by adits; in consequence adit levels were developed at horizons 865, 795, and 760 meters above sea level, and the levels in the mine 'are named according to their elevation. Exploitation started from the 760-m. level . upwards while simultaneously first steps were taken with regard to mining in depth. A deep dewatering adit 2.5 km. long now gives access to the deposit at the 610-m. horizon which also is connected with the 760-m. adit level by a three-compartment main hoisting shaft. Main levels have been developed internally from

Jan 1, 1936

By B. C. Riblet

THE president of a large smelting and refining company once telegraphed me that they had acquired extensive mining interests in northern Peru and requested me to inspect their properties as it would be necessary to install a system of aerial tramways between their mines and treatment plant. The concentrator was about 50 mi. from the coast, reached by a fairly good motor road. From the concentrator an aerial tramway would he required, about 6 mi. long, to their first property, a gold and silver mine. The lower terminal of the tramway was at an elevation of 4000 ft. and the mine at an elevation of 9500 ft.

Jan 1, 1937

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

By E. P. Bayer

MESABI RANGE ore is mined largely by the open-pit method. This involves having available at all times sufficient working places which in combination will produce ore of guaranteed analysis. Fast- loading power shovels turn out under favorable conditions 1000 tons per hour from each unit. Each unit loads ore differing materially in analysis from that loaded by the others, One may load high grade, another low grade, and another may be in a mixed bank with the lead ore so placed that the product must be mixed at the shovel before it is loaded into cars. In such cases the bank is combed with the bucket, the door being left open to permit the material to fall through.

Jan 1, 1937

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

By George C. Bateman

WE in Canada want to see industry get back to a normal economic basis as soon as possible but wartime controls cannot be dispensed with immediately the war is over. Perhaps never again will we be entirely free from some of the types of controls such as those set up during the war. Certainly the taking over and disposal of surplus materials contemplates the continuation of some form of control for many years to come. However, to the extent that it is possible, the Allied nations are exponents of free enterprise.

Jan 1, 1944