Search Documents

By K. E. Waters, N. Brodusch, R. Gauvin, A. Jordens, Teng. C., H. Demers

Rare earth elements (REEs) become increasingly significant for renewable energy devices and high-technology electronic products because of their large-scale popularity and applications. In this project, a field-emission scanning electron microscope was used to characterize the composition and distribution of REEs-bearing minerals. X-ray elemental maps were acquired with a large area x-ray detector (60 and 80 mm2 collecting area) and annular detector (60 mm2 collecting area), which allow fast x-ray acquisition at high count rate. These elemental maps were transformed into phase maps, which are used to identify the composition of the mineral phases and the REEs distribution over a large area. The phase maps are an easy way to distinguish the phases with and without REEs and compare the efficiency of different REEs extraction processes. Different methods (manual and automatic) for producing phase map were studied by comparing the distribution of REEs obtained from the same area.

Jan 1, 2015

By Fearnsides W. G.

Discussion at the The Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.409-448, included oral contributions by Lupton A. on the mechanisms of subsidence and water egress and by Kendall P.F. on the validity and accuracy of the contour extrapolation technique and the effect of major faults, together with the author's response

Dec 1, 1916

By R. M. Lamya

A considerable part of gold encapsulated in some refractory sulphides can be dissolved during sulphide matrix decomposition in non-complexing aqueous media. This has been concluded from laboratory results of gold extraction from pyritic and arsenopyritic concentrate containing 172.8ppm Au, into 10% hydrochloric, sulphuric and nitric acids. The degree of sulphides decomposition in the non-oxidative acids limits the gold extraction from this specific concentrate to about 10%. In the case of nitric acid, the gold dissolution follows the rapid decomposition of sulphides, reaching 32 to 42% of extraction at almost total decomposition of the sulphidic minerals. Accumulation of gold in this acidic and non-complexing solution to several ppm was not affected by the soluble products of the sulphides decomposition. An attempt to explain this gold behaviour is undertaken and some practical implications are discussed. In the investigated concentrate the "soluble gold" is mostly associated with arsenopyrite. This is consistent with the latest findings of other authors that gold disseminated in arsenopyrite can occur as cation Au3+. In a comparative test the gold extraction into highly concentrated chloride solution, in the same oxidative conditions, amounted to 92.34%.

Jan 1, 1995

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By K Williams, T Donohue, W Chen, T Roessler, A Katterfeld

Wet sticky iron ore poses particular difficulties in every aspect of the material handling process. Material hang-ups in bins, pipes and chutes; carry-back and spillage due to insufficient belt cleaning; clogging of screens; malfunctioning of crushers as well as rat holing of gravity reclaimed stockpiles are all predominantly due to the inherent cohesion and adhesion characteristics of the wet, sticky ore (Roberts, 1993). Limited understanding and quantitative measures on the stickiness of such a material significantly lower the mining operation efficiency.This research aims to investigate the cohesion and adhesion characteristics of the wet, sticky ore on physical modelling, experimental techniques and numerical implementation. Initially, the suitable bridging mechanism that contributes to the cohesive and adhesive forces within the iron ore material was identified (Hering, Martin and Stohrer, 1989; Rumpf, 1958). A cohesion/adhesion energy density factor based contact model was then introduced to describe the stickiness of the material. Secondly, an experimental system was proposed to directly test the stickiness of the material. Such a system is able to obtain both the cohesive/adhesive shear force and tensile force of the material at a specific moisture content. Lastly, the implementation of the proposed cohesion/adhesion model into the discrete element modelling (DEM) software was also discussed. A cohesion/adhesion calibration for modelling wet sticky iron ore in DEM was then conducted to ensure the material modelled in the simulation is reflective of the reality.From the study, understanding of the cohesion/adhesion characteristics of the wet iron ore material is significantly enhanced. Experimental and numerical outcomes can be directly applied for better designing or optimising the material handling processes that involve wet sticky iron ore. Consequently, the mining operating costs can be greatly reduced.CITATION:Chen, W, Donohue, T, Williams, K, Katterfeld, A and Roessler, T, 2015. Modelling cohesion and adhesion of wet, sticky iron ores in discrete element modelling for material handling processes, in Proceedings Iron Ore 2015, pp 387–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Joel Ochoa, Miguel A. Montiel

El artículo da cuenta del estudio de un prototipo de placa de desgaste para chutes de transferencia con un nuevo sistema de sujeción. El sistema fue validado mediante el software Ansys. La innovación no solo está constituida por un nuevo diseño sino también por el tipo de proceso productivo para la fabricación del producto mejorado. Se incluyeron ensayos con torquímetro, que presentaron resultados favorables.

Sep 30, 2019

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab&apos;s Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005

By M. J. Adam

The U.S. Bureau of Mines is investigating the partitioning of selected complex minerals into simple phases using sulfidation reactions. Successful partitioning of complex mineralogy to simple phases may afford an opportunity to improve selective extraction of mineral constituents of economic value. The research has shown that complex minerals, such as chalcopyrite (CuFeS2) and pentlandite [(Fe,Ni)9Se]&apos; may be partitioned to the simpler phases covellite (CuS) plus pyrite (FeS2) and vaesite (NiS2) plus pyrite (FeS2), respectively. Demonstrations of these reactions were verified through long-react ion-time (24 h or more) experiments, but basic rate investigations and modeling were not included in the previous research. This report describes research aimed at determining the rate at which the complex mineral CuFeS2 converts to the simple sulfides CuS plus FeS2. Small samples of CuFeS2 were blended with elemental S prior to thermal treating under an He atmosphere for time periods up to 4 h. Products from each treatment period were characterized using metallography, chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Results of the investigation revealed a rapid conversion of CuFeS2 to CuS plus FeS2 early in thermal treatment periods. As the reaction occurred, a CuS rimming of particles was observed which separated the reacting species (CuFeS2 and S) and caused a considerable decrease in transformation rate.

Jan 1, 1991

The cloud transform simulation is a technique used to generate realisations of correlated attributes. The principle of this technique is to partition the scatter diagram between the input attributes into several interval classes and derive for each class a cumulative distribution function (CDF) using only the data pairs of the scatter diagram in that class. The simulation then proceeds like a traditional Monte Carlo simulation but using the derived CDF in each class.The cloud transform simulation has the advantage of being a simple and fast technique that is able to reproduce the uncertainty in the relationship between the two input attributes regardless of whether the relationship is linear or not. However, the technique has three major drawbacks. First, the number of classes has an impact on final simulated results and there is not a robust approach to define such number. Second, simulated results exhibit some saw tooth variations that are unrealistic and third the reproduction of the spatial continuity of the simulated attribute is not guaranteed.This paper presents the use of the quantile regression approach in order to overcome the first two disadvantages of the cloud transform simulation. Details of the technique and how it can be coupled with the cloud transform simulation are presented along with a real case study.

Sep 26, 2011

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker&apos;s compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995

By Douglas G. Fox

Outputs from industrial activities planned in the Riley Ridge natural gas project are modeled to determine the potential locations of air pollution impacts on the Bridger and Fitzpatrick Wildernesses in Wyoming. The nature of modeling, especially with regard to its realism, is discussed. Alpine lakes which, along with their watersheds, have minimal buffering capacity are being studied because of their sensitivity to acidic deposition from proposed new air pollution sources. A hypothesis which relates a source&apos;s emissions to deposition and lake chemistry in a worst-case sense is presented. Research designed to test the hypothesis and reduce uncertainties is outlined and progress reviewed. Focus is placed on the meteorological transport and atmospheric deposition parameterization contained in the hypothesis.

Jan 1, 1984

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual&apos; usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system&apos;s performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Clifford J. Lewis

The control of sulfur dioxide and fly ash in the emissions from coal-fired boilers is a significant segment of the national environ- mental protection program. Developing technologies to accomplish this objective presently emphasize aqueous scrubbing techniques. Should circumstances require aqueous scrubbing for fly ash control only, provision must nevertheless be made to counteract the presence of sulfur dioxide which can create an acidic and potentially corrosive environment. Major technologies for sulfur dioxide control by aqueous scrubbing include, l), recovery processes yielding sulfuric acid or elemental sulfur and 2), throw-away processes which produce a sludge consisting essentially of calcium sulfite or varying amounts of calcium sulfate.1/ Recovery processes are more sophisticated and best suited for locations where there are markets for sulfuric acid or sulfur, or where sludge disposal is an overriding consideration. Throw-away processes are generally less sophisticated but have a problem in that gas scrubbing systems may not operate for practical time periods without failures due to corrosion and to plugging by particulates and precipitates. To overcome this difficulty, some throw-away systems employ an aqueous solution of caustic in the gas scrubbing device to assure maximum water solubility of sulfur compounds, followed by the addition of lime to the scrubbing medium in a system external to the scrubber to produce the throw-away sludge and regenerate the caustic for recycle. Such systems are referred to as double alkali systems.2/

Jan 1, 1975