Search Documents

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By Derek V. Ellis

Sediment Quality Guidelines can provide target values that should not be exceeded when seabed deposits are disturbed for mining, waste discharge or other purposes. Three sets of Guidelines have appeared in 1994 and 1995: US NOAA (updated from 1991), Environment Canada (EnvCan) and Equilibrium Partitioning (EqP) developed in the UK from US Water Quality Criteria. The US NOAA and EnvCan Guidelines have been developed by comparing many experimental and site data sets, and have concluded that levels below which effects rarely occur, or above which probably will occur, are useful guidelines. US NOAA uses the terms ERL and ERM for these two levels, and EnvCan TEL and PEL. The EqP concept is that a value can be calculated below which trace metals present cannot raise the concentration in the interstitial water. There are some problems in comparing units, but the comparison shows in general that the EnvCan levels are less than, and down to half of, the US NOAA levels. EqP levels vary but are generally fairly close to US NOAA ERL levels, with one major exception. The EqP level for mercury is far lower than either US NOAAor EnvCan levels, at 0.008 mg kg-1 compared to 0.15 (ERL) and 0.13 (TEL) mg kg-1 respectively. Comments will be solicited on how such differing Guidelines should be used site-specifically for environmental management at mining operations, (1) in the regions for where they were developed, and (2) elsewhere.

Jan 1, 1995

C. E. Dewey, Georgetown, Colo. (communication to the Secretary) : In his remarks on crushing-machinery, Mr. Douglas says (Twins., xxii., p. 322): "To insure a smaller and more uniform size of particles in the crushed material, the Dodge crusher still communicates motion to the upper extremity of tile movable jaw, which oscillates on fixed pivots projecting from its lower extremity!' The notion that, in order to obtain a fine and uniform product from a rock-breaker, the movable jaw must be pivoted at its lower extremity, seems to obtain generally among mill-men, as well as among manufacturers of machinery. My experience with machines of both types does not confirm this belief. It is true that, to obtain a uniformly fine product from a jaw-crusher, the stroke at the lower extremity of the crushing-surface must be short; but that the movement at that end must be less than at the other or receiving-end is, I think, an erroneous assumption. Figs. 1 and 2 are intended to illustrate the two types of machine. It is found in practice that the capacity and the nature of the product of either machine, as usually constructed, are governed by the opening, C D, and the length of stroke of the movable jaw at D. This being the case, machines of either type, of the same width of crushing-surface, running at the same speed, and having the same adjustment as to opening and stroke at D, should give, when fed

Jan 1, 1895

In this year marking the centennial of the Geological survey of Western Australia, it is appropriate that we should review the value of the contribution of the Survey, and Australian Geological Surveys in general, to the exploration industry. Most geological surveys in Europe and North America had their origins in the first half of the 19th Century when the burgeoning Industrial Revolution was demanding the identification of new sources of coal and iron ore. Australia, as a young nation, essentially dependent on an agricultural and pastoral industry, and with already discovered vast coal resources in Eastern Australia, had, no great need to explore for new mineral resources. However, with the discovery of gold in 1851, the mineral potential of the country became apparent to the whole world and the first Geological Survey in Australia was set up in 1852 in Victoria under A.R.C. Selwyn. After a number of false starts all Australian States had an established Geological Survey by 1900. It is hard to assess the contemporary value of the early work of the Geological Surveys with respect to exploration, almost all major mineral discoveries were made by prospectors and most mining companies had little time for geologists - although the Chamber of Mines in Western Australia in 1910, did recommend that the Geological survey be granted an additional ten thousand pounds over two years to map all existing goldfields and the country between them, and produce a reconnaissance map of the area east of a line between Wiluna and Edjudina as far as the South Australian border!

Jan 1, 1988

By Emily Wortman-Wunder

Attendees at December?s Arizona SME Section Conference at the Hilton El Conquistador Resort outside of Tucson, AZ were feeling optimistic and ready to get to work after a year of steady growth and recovery in the mining industry. During the two-day event (Dec. 5-6, 2010) and the preceding American Mining Hall of Fame banquet and awards ceremony, the focus was on copper, worldwide population growth and regulatory pressures, with several smart new projects featured alongside updates to traditional large-scale copper development projects. Keynote speaker Timothy Snider, chair of the University of Arizona?s Lowell Institute for Mineral Resources, hit the mood of cautious optimism when he analyzed the global demand for resources, using the case example of copper. Over the next 20 years, he said, the world?s population is expected to grow to 9.2 billion and the average annual per capita copper use is expected to rise from 2.2 to 4.5 kg (5 to 10 lb). The increase in demand will provide tremendous opportunity for mining companies, he said, but cautioned that the opportunities are balanced by negative influences on demand and pressures on supply. While demand for copper is currently growing, Snider noted that there were significant downward pressures on demand as well. These included a western world that is overbuilt, in-creasing use of substitute materials in new construction and the rise of wireless devices. He also noted new regulatory pressures, and pointed out that resource development now had to occur within a context of sustainability on several levels.

Jan 1, 2011

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high' throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

By P. Halbach

Hydrothermal activity is well known from many locations on most mid-ocean ridges, but no hydrothermally mineralized area had yet been found at the ultraslow spreading southwest Indian Ridge up to October 98 when the Japanese RV Yokosuka with the submersible Shinkai 6500 investigated this area. A massive sulfide field was discovered near 27°51S / 63°56E in the 11th segment west of the Rodriguez Triple Junction. The Free University of Berlin had joined this cruise and taken over the responsibility for the study of the respective sulfide mineralizations. Hydrothermal minerals were sampled during two dives at a water depth of 2940 m close to the summit of an axial volcanic ridge called Mount Jourdanne. Massive sulfides occur on the seafloor as small smooth mounds with an average area of about 5 m2. Their surfaces are weathered and have a reddish to brownish colour. In addition to these mound-like structures, small tube-like chimneys were observed; these chimneys rise approximately 30 to 40 cm above the floor and are less than 10 cm in diameter. No indications of hydrothermal fauna could be detected. All the hydrothermal features are spatially related to faults and smaller fissures controlled by an E-W trending graben system crossing the summit region of the submarine volcano. Such tectonized areas are generally considered to be ideal for hydrothermal activity because they may have both a magmatic heat source in the deeper underground as well as pathways for the fluid circulation.

Jan 1, 2002

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991

By Peter Halbach

Hydrothermal activity is well known from many locations on most mid-ocean ridges, however no hydrothermally mineralized area had yet been found at the ultraslow spreading southwest Indian Ridge up to October 98 when the Japanese RV Yokosuka with the submersible Shinkai 6500 investigated this area. A massive sulfide field was discovered near 27º51S / 63º56 E in the 11th segment west of the Rodriguez Triple Junction. The Free University of Berlin had joined this cruise and taken over the responsibility for the study of the respective sulfide mineralizations. Hydrothermal minerals were sampled during two dives at water depth of about 2940 m close to the summit of an axial volcanic ridge called Mount Jourdanne. There massive sulfides occur on the seafloor as small smooth mounds with an average area of about 5 m2. Their surfaces are weathered and have a reddish to brownish colour. In addition to these mound-like structures, small tube-like chimneys were observed. These chimneys rise approximately 30 to 40 cm above the floor and are less than 10 cm in diameter. No indications of hydrothermal fauna could be detected. All the hydrothermal features are spatially related to faults and smaller fissures controlled by an E-W trending graben system crossing the summit region of the submarine volcano. Such tectonized areas are generally considered to be ideal for hydrothermal activity because they may have both a magmatic heat source in the deeper underground and pathways for fluid circulation, respectively.

Jan 1, 2001

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By Bahngrell W. Brown

IN an age when anything short of miraculous can and does happen it is entirely too easy to become labeled as a prophet. After the first wave of hysteria over atomic weapons died down there were crystal gazers enough in that field. The mining fraternity, always anxious to get back to normal anyway, looked, was duly impressed, and passed on to more mundane affairs. After all it was just another big blast in the stopes of life. After we "laymen" had seen the effects at Hiroshima and been granted a peek into the phenomenon of Numbers 4 and 5, we saw, indeed, that it was a tremendous but understandable weapon. Now it appears that we may fall heir to much of the defensive planning of the future. If, as our military planners tell us, it will be necessary to go underground for defense, then we are the true forerunners of a race of troglodytes. The underground belongs to us as to no other profession; the subsurface is our prerogative. Already the big mistakes in planning atomic defense are being made. It is within our ability now to correct them. Surveys are being made of natural caverns to be used as a basis for military planning. This is our first big mistake. Even if the natural caverns, many of which Nature has precariously carved from cherty and brittle limestones, could withstand the seismic force of a proximate blast without major roof failures, there is a more serious argument against the blanket use of natural caverns as a first line of defense. In addi-

Jan 1, 1946

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By S. Nowosad, O. Langefeld, A. Godge

Pumped storage power plants are one of the options to store the fluctuating production of electric energy from renewable sources in a sustainable manner and is able to provide Europe with the opportunity to overcome the effects of climate change. However, due to the extensive land use required when planning the water reservoirs, several projects have been declined after social conflicts raised, even in Germany. Nonetheless, after the flooding and drought periods in northern Germany, the catastrophic floods of July 2021 in south west Germany, the country’s need to decrease its dependency on import of gas and energy supply, and the energy transition goals set for 2030 and 2050, it has become clear that the implementation for water reservoirs must increase in the coming years, whether above ground or underground. Furthermore, not only Germany is interested in the use of underground cavities for water and energy storage, other European countries as Sweden are currently developing studies and solutions to bring this concept soon to reality in Europe. This article introduces the systematic approach for planning and designing large underground cavities for water reservoirs as a sustainable energy transition approach and a climate change response by showcasing the process of selection and results of the “Energy and Water Storage Harz” (EWAZ) research project. Additionally, the results of the evaluation of the effect of implementing the selected underground and surface infrastructure into the current water management system in the region is presented. Finally, the different possibilities evaluated for the underground cavities within the project and the technical challenges involved are be discussed.

Feb 1, 2023

By Mokka Rao, Arturo Valles, Jose Rodríguez

"This paper shows a mathematical model based on finite elements, applied to bottom poured shell ingots of C.V.G. Sidor Plant. The model was used as a strategy to determine the thermal effects that are produced when solidification conditions are modified without interfering with the production process. The modification consisted of placing a thermal insulator on top of mould.The results obtained by the model indicated that the solidification time increases with insulator on base of the mould. With these results a significant number of casts were run with and without insulator. Latter by means of a metallurgical analysis it was determinated that the ingots cast with insulator reduce the level of non-metallic inclusions and the presence of internal blistering in seamless pipes.IntroductionThe process of fabrication of seamless pipes in SIDOR involves various steps of processing, such as heating the ingots, fabrication of the prelaminated, fabrication of the bored pipe, lamination of the pipe by passing through the pellegrine mill, heating the pipe in a walking bean furnace and final calibration through a calibrator mill. The material utilized for producing these pipes is provided entirely from a electrical arc furnace and casted ingots, especifically, from the superintendence of bottom pouring.The process of bottom pouring consists of positioning twelve moulds of diameters 415, 480 or 505 mm over a plate of grey cast iron in which exists a system of communicating vessels. The ingots are distributed around a central duct from which the steel flows down and filling gradually, each one of the moulds (Fig. 1)."

Jan 1, 1997

By W. R. Tyson

IT HAS BEEN KNOWN for many years that alloy steels can become brittle when tempered in the range of 350-600°C, or cooled slowly after heating to higher temperatures. The metallurgical literature reveals that blacksmiths were aware as early as 1883 that water quenching was necessary after heat treatment above 600°C to avoid brittleness. It has also been known for years that the problem is associated with trace impurities; a paper in the Journal of the Iron and Steel Institute of 1894 refers to the brittle, faceted fractures that occur in steels containing arsenic, phosphorus or sulphur. However, definitive investigation of the mechanism of embrittlement has been possible only within the last decade with the introduction of new experimental techniques to investigate surfaces, especially Auger electron spectroscopy. It is now possible to study in detail the chemistry of surfaces with a resolution of an atomic layer or two, and enormous progress has been made recently in studying the segregation of impurities to grain boundaries by exposing the boundaries by fracture inside the microscope. A clear picture of the processes occurring and their interpretation is now emerging, as was particularly clear at the recent 1977 ASM Materials Science Seminar on Interfacial Segregation held in Chicago in October. Recent research in this area has pointed the way for commercial exploitation of this new knowledge and experimental technology. It is the purpose of this article to trace progress in understanding temper embrittlement and to indicate other areas where control of interfacial segregation and its effects can be important in metallurgical applications.

Jan 1, 1978

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960