Search Documents

By J. J. Becker

Changes in magnetic properties with particle size are used to study the precipitation process in a Cu-Co alloy. In particular, the effect of a field during aging in producing anisotropy is shown to occur entirely during the growth of the particles, after precipitation is complete. HEAT-treatment in a magnetic field is done commercially to improve the magnetic properties of a number of materials. These can be divided into solid-solution alloys and precipitation alloys. The Permalloys are representative of the first type, and magnetic annealing greatly increases their maximum permeability. On the other hand, in precipitation alloys such Alnico 5 the important result is an increase in maximum energy product. The effect of the field in all cases is to bring about an additional magnetic anisotropy, uniaxial in nature, which makes the hysteresis loop more upright when measured in the direction in which the field was applied. The structural origin of the anisotropy brought about by magnetic annealing is not well understood. In the solid solution alloys, one possible explanation is based on ordering.' Another possibility is the orientation of like-atom pairs.' The precipitation systems known to respond to magnetic heat treatment are Alnico 2, in which the effect was first discovered," Alnico 5, cobalt ferrite (oxide),' and Cu-Co alloys.3 n these materials, the field affects the precipitation process itself in some way. Although there has been much work on Alnico 5. its nature is still incompletely understood. According to Geisler,' the precipitation reaction is of the

Jan 1, 1959

By L. A. Mekler

THE recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are .constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to that produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack.

Jan 1, 1928

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

The following is based on two examples of emission control with coal fired power stations as practised in Germany at Heilbronn Block 7 power station and the Rheinbraun coal combined power station with integrated high-temperature Winkler system (HTW). Heilbronn Block 7 demonstrates the successful emission control of sulphur and nitrogen oxides and the (HTW) system the reduction of the specific carbon dioxide emission. Both were sparked off by legislation which demanded certain emission control standards. Since the early eighties environment protection has been a matter of heated public debate in the European Community. A recent survey in Germany showed unemployment as being the only subject matter more frequently in the minds of people than environment protection. A new kind of forest devastation in areas away from industry has caused investigations by several government departments and private enterprise. Because of lack of conclusive evidence so far, the principle of PRECAUTION has replaced the CONCLUSIVE evidence as a base for new legislation concerning the environment. The new legislative standards for nitrogen oxide emissions in Germany for example have reduced NOx emissions of power stations from 1000 mg NOx per cubic metre of flue gas in the beginning of 1983 to 200 mg NOx per cubic metre of flue gas in April 1984. These new standards were enshrined in legislation when research provided some evidence linking nitrogen oxide emissions through photo-chemical reactions with forest devastation. Thirty European countries signed a treaty in 1983 expressing their concern about air pollution and their willingness to co-operate with each other in controlling large scale emissions.

Jan 1, 1991

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By E. N. Durussel

"The Fox Mine has been producing copper/ zinc ore since 1970 at a rate of approximately one million tons per year, and until 1978all production was derived from longhole open stopes. In June 1978, a trial stope using bighole mining methods was started to eliminate the development of two sublevels between 400 level and surface. The trial proved to be successful, and bighole mining is now an accepted mining method for both stopes and pillars at Fox Mine.When production blasting was started in the first stope, the biggest problem encountered was the production of large amounts of sulphur dioxide gas as a result of secondary sulphide dust explosions. This gas generation resulted in lost production time and caused minor damage to underground installations to the blast level, and to the headframe. Sulphur dioxide generation has been noted in secondary drawpoint blasts and, on rare occasions, in drift rounds.This paper discusses the occurrence of the sulphur blasts and the practices and precautions used to prevent their reoccurrence at Fox Mine.IntroductionThe Fox minesite is located 30 miles southwest of Lynn Lake, Manitoba. With production startup in 1970, Fox Mine is owned and operated by Sherritt Gordon Mines Limited.The Fox orebody occurs as a large lenticular zone of semi-massive sulphides approximately 1,500 feet long and 15 to 100 feet wide running east and west. Dipping 70 degrees to the north, the orebody tends to bottom out at the 3200-foot level and reaches to within 15 feet of surface."

Jan 1, 1981

This paper examines manning best practice in the Australian mining industry, comparing the mining of gold with mining of other commodities. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 7 open pit and 14 underground studies of gold mines in Australia from a database of over 50 studies. The data were collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2009. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. The proportion of supervisory to operations personnel and labour costs as a percentage of total operating costs is highlighted. Minimum manning requirements for the range of mining methods are indicated, irrespective of the size of the operation. The benchmarking results provide guidance by indicating a range of manning numbers and trends which are likely to be appropriate for the scale and type for a range of mining operations. When combined with benchmarked productivity and cost data, manning results help identify potential areas for business improvement, driving gains in the efficiency of labour. Finally, the paper considers perspectives on best practice for manning and the limitations in application of this type of analysis in a global context.

Jan 1, 2009

By W. P. Heineken, A. T. Child

This paper presents the results of a series of experiments made in the metallurgical laboratory of Columbia University, New Pork City. The object of the investigation was to determine, as far as possible, the changes in micro-structure and physical properties caused by short periods of heat-treatment and the longer malleable cast-iron process. It was proposed to do this by means of micro-photographs, heating- and cooling-curves, and tensile tests after the various heat-treatments. I. Micro-Constituents of Iron and Steel. The list of the micro-constituents of iron and steel has grown till now it includes seven different substances, called ferrite, cementite, pearlite,* martensite, austenite, sorbite and troosite. Only the first five of these are mentioned in this paper, to facilitate the understanding of which, the following brief definitions are given: 1. Ferrite (named by Prof. Howe) is, chemically, iron free from carbon. It is the softest of the constituents, and is not colored by etching, except when long-continued. Under the microscope it is easily determined by its regular polygonal etructure; or, if structureless, as in malleable cast-iron, by the ease with which it is scratched. Ferrite appears in mild steel in small amount, in grey cast-iron, and in malleable cast-iron. 2. Cementite (also named by Prof. Howe) is now generally conceded to have the formula Fe3C. It is the hardest of the micro-constituents, having the hardness indicated by 7 of the mineralogical scale; and hence it is always left in relief after

Jan 1, 1901

By W. Wanjokow, H. O. Hofman

In the metallurgical treatment of most metallic sulphides it is usually necessary to carry on a roasting-operation. In some cases the raw ore will have to be roasted; in others the intermediary product, matte, produced in smelting the ore; again, both ore and matte may have to be subjected to oxidation at elevated temperatures. Most metallic sulphides, when given an oxidizing-roast, pass through the state of sulphate before they are converted into oxides. All metallic sulphates are completely decomposed by heat, with the exception of those of lead and bismuth, but the temperatures at which decompositions take place vary with the metals. Some metallic sulphates are converted directly into oxides, others first form basic salts. Alkali-earth sulphates show a behavior similar to that of metallic sulphates, while alkali sulphates do not part with their sulphur trioxide even at elevated roasting-temperatures. The older data on the decomposition of metallic sulphates by heat are only approximations. Thus Kerl' gives the order in which metallic sulphates are decomposed with increasing temperatures as (Ag2, Fe, Cu, Zn, Ni, Co, Mn, Pb) SO,. More recent statenlents give definite temperatures and modify the formerly accepted order of decomposition. But the temperatures given by various observers do not agree. The reasons for this are to be found mainly in the method and manner of carrying out experiments. Four methods have been used: 1. Heating in an evacuated tube; 2, heating in a tube closed at one end, without air-cur-

Jan 1, 1913

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

Question 1—1s Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions. Especially in Limestone or Other Dense Rocks Discussion by: A. M. Bateman.........120 S. F. Kelly........... 125 C. H. Behre. Jr........118.123 G. B. Langford......... 123 T. M. Broderick.........121 H. E. McKinstry......... 116 R. H. Clarke.......... 123 D. H. McLaughlin........ 118 J. D. Forrester for M. H. Gidel . . 11.4 W. H. Newhouse......... 123 G. M. Fowler......112. 116. 121 R. H. Sales.......... 116 L. C. Graton..........121 Edward Sampson......... 122 R. D. Hoffman.........120 J. 8. Stevenson.......... 117 I. B. Joralemon.........121 L.B.Wright........... 112 Question 2—What Are Some of the Chemical and Physical Characteristics in Certain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? Drscussion by: G. W. Bain....... 127 G. M. Fowler....... 131 C. H. Behre, Jr. ..... 131 L. C. Graton....... 128 J. S. Brown. ...... 126 G.. F. Loughlin...... 128 E. L. Bruce ....... 129 R. H. Sales........ 129 R. H. Clarke...... 130 A. K. Snelgrove....... 130 Question 3—Are There Any Criteria by Which One Can Determine When Mining Operations Have Reached the Roots of an Ore Deposit? Discussion by: J. M. Boutwell...... 139 G. B. Langford..... 139 T. M. Broderick..... 138 . G. F. Loughlin...... 135 E. Y. Dougherty..... 137 R. H. Sales...... . 134 G. M. Fowler....... 132 F. A. Thomson..... 136 I. B. Joralcmon...... 132 Edward Wisser:..... 140 General s. F. Kelly................. . ...........145 References...............................146

Jan 1, 1941

A short overview of the research program of SveBeFo, Swedish Rock Engineering Research, which was founded in 1993 is first given. Then four recent and ongoing projects in rock blasting and explosives engineering are presented in greater detail: 1. Burn Equations for Commercial Explosives. 2. Blast Damage in Contour Blasting. 3. The Role of Gas Pressure in Pit Wall Damage. 4. Fragmentation of Aggregate Rock. The goal of the bum equation project is to be able to control the energy release from explosive charges to the desired part of the expansion curve of the reaction products under various rock conditions. SveBeFo's work has reached the stage where a burn equation for a lab emulsion has been established which can model the influence of charge diameter on the VOD and detonation front curvature in a cylindrical charge quite well. This work now continues with other emulsion recipes. In the blast damage project the goal is to develop techniques and recommendations on how to minimise the blast damage in construction blasting. The project has gained extensive practical knowledge from the blasting of more than 200 holes in a granite quarry under controlled conditions. The cracks in the rock surrounding the contour holes have been cut open and measured. The influence of factors like charge concentration, decoupling ratio, hole and charge size, VOD and time delay in initiation have been investigated. A simultaneous initiation of a group of contour holes with EDD detonators is quite superior to single hole blasts, even when they are timed as closely as 1 ms.

Jan 1, 1995

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By R. P. Taylor

"This paper covers the development of the property to its present production level of20,000 tonnes per day from the Valley Mine. It will also review the analysis of various case studies for the expansion of the project to its full potential, and discuss the impact of the recent structural change in the copper market on the development of a large low-grade deposit such as Valley.IntroductionIn 1964 Cominco participated, along with a number of other companies and individuals, in the formation of Valley Copper Mines Ltd. This company was formed in order to facilitate exploration on a large number of mineral claims held by these parties in British Columbia's Highland Valley, approximately 400 km northeast of Vancouver (Fig. I). Cominco 's ownership of Valley Copper was gradually increased over the years bot h through shares gained for exploration expenditures and through shares purchased on the open market. By the mid- 1970sCominco' s interest in Valley Copper exceeded 80%.ExplorationExploration from 1964 to 1969 led to the discovery of a massive porphyry copper depo sit now known as the Valley orebody. A claim boundary divided the deposit with 80% of it on Valley Copper claims and 20070 on claims held by Bethlehem Copper which was already mining adjacent copper orebodies. During the period when the Valley ore body was discovered, exploration by other companies resulted in the discovery of the large Lornex and Highrnont deposits nearby. The stage was now set for the Highland Valley to become an important copper-producing area (Fig. 2)."

Jan 1, 1986

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By R. C. Hartviksen

"The Drumbo Mine is a new gypsum mine located at exit No. 32 of Highway 401 between Woodstock and Kitchener, Ontario. The flat-lying 6-foot (1.8-metre) bed of gypsum is near the base of the Silurian Salina Formation, about 380 feet (116 metres) below surface. The mine is owned and operated by Westroc Industries Limited. A shaft, 12.5 feet (3.81 metres) in diameter, was drilled and then lined with a liner-sinking technique new to this continent. The shaft was completed in the fall of 1977. Gypsum production was started in December 1978, employing a conventional room - and - pillar method of mining.Historical BackgroundA brief mention of gypsum in the Drumbo area is included in a survey of the Ontario gypsum industry by Guillet. This occurrence was discovered in 1958 when National Gypsum conducted some widespread diamond drilling. Western Gypsum Products Limited acquired leases in 1960 and concentrated a drilling program in Blenheim Township near the village of Drumbo; 79 holes were drilled in an area of 1900 acres (770 hectares). Mining rights were then acquired for 170 0acres (690 hectares). A test shaft, 44 inches (1.1 metres) in diameter, was drilled to obtain a 50-ton (45-tonne) bulk sample. This opening will be used as an emergency escape way and for ventilation.Westroc Industries Limited, a wholly owned subsidiary of BPB Industries, has its head office at Mississauga, Ontario and operates gypsum board plants at Mississauga, Vancouver, Calgary, Winnipeg and Montreal. Other gypsum mines are at Windermere, B.C. and Amaranth, Manitoba."

Jan 1, 1983

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942