Search Documents

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

The steam-filtration process for dewatering solids involves the application of slightly superheated steam to a filter cake during filtration. The mechanism by which the technique promotes water removal has been deduced from bench-scale experiments on coal and on granular iron ore concentrates. The mechanism, along with some of the applications and limitations of the process, is presented. Introduction I N the steam-filtration process, slightly super-heated steam is applied to the filter cake during filtration to remove more water than can be extracted by conventional filtration. Although this process was developed by Burton for coal filtration (1), it should have far wider applicability; certainly, it could be used to treat any mineral product, because only low-temperature steam is needed and most conventional filtration equipment can be easily adapted to it. As few restrictions apply to this process, however, it is important that its more obvious advantages and disadvantages be appreciated and, especially, that the criteria on which economic evaluations can be based are understood.

Jan 1, 1965

By J Jeffery, P G. Knott, F Velge, C Evans

A trigger action response plan (TARP) provides a structured response to escalating levels of risk. In mining, TARPs are typically applied to primary hazards such as inrush, strata failure or heating. Necessary for the creation and deployment of a TARP is a monitoring system capable of detecting deviations from normal conditions. The advent of real-time instruments capable of measuring diesel particulate matter now permit decision-making within shifts to address possible overexposure. Deploying a TARP for diesel exhaust emissions can lower the probability of a person’s average exposure (over a full shift) exceeding the exposure standard by detecting deviations of diesel particulate concentrations from normal conditions. This enables pre-emptive action to mitigate or protect. Another goal is to drive ambient air concentrations lower through the application of corrective actions as a result of instances where concentrations exceed ‘normal’.CITATION:Knott, P G, Evans, C, Velge, F and Jeffery, J, 2015. Trigger action response plans for diesel exhaust exposures, in Proceedings The Australian Mine Ventilation Conference, pp 129–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018

By W. H. Fertl, S. J. Pirson

Well logging techniques, as used successfully in oil and gas exploration, can also be used to give a detailed evaluation of drill holes through industrial mineral deposits such as sulphur. This paper describes the logging tools used gives the theory behind the well-log interpretation and discusses the application of the method in sulphur-bearing limestone and m more complex sulphur deposits.

Jan 1, 1970

By Raymond Henn

Yes we have also used some however, again because of the nature of the maintenance window where we have that two hour (at best) window every night and due to the numerous other crews that are wanting to get in to do the other types of maintenance activities, we don't know if we are going to be getting into that same area from one night to the next. So even with the dormancy additives that one can add to cementitious grouts (that are good up to 72 hours) we don't know if we are going to get back in to the same locations from one week to the next. That's why I use the term "the forgiving nature of the acrylamide". It allows us to ream out the hole allowing us to use the exact same hole without having to re-drill a new hole. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. Up to the end of 2001 we were just over 1.7 million liters of between AV100 and AV118 grout. Of that, approximately just under 200,000 was AV100 and the remaining balance was AV118.

Feb 10, 2003

By William H. Lehr

In recent years, we have witnessed many innovations in the equipment used in handling bulk materials. Not too long ago, any sizeable stockpile of coal or iron ore was attended by one or more material handling bridges. More recently, large stockpiles have been built with mobile equipment of' the earth moving type with bulldozers and front end Loaders being utilized in reclaiming operations. The most recent stocking and reclaiming device is the rotary bucket wheel machine. The early bucket wheel machines built in the United States were developed for the strip mining of coal. We understand that the first American machine was built in the Midwest in 1944. This type of unit was developed in an effort to reduce the cost of removing overburden and to provide satisfactory spoil disposal. As the available coal reserves under shallow cover were exhausted, the cost of removing the deeper overburden with conventional equipment became too great for these operations to continue profitably. The first machine has now been followed by six or seven additional units, the largest of which can handle material at a rate of more than 7000 cubic yards per hour.

Jan 1, 1965

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is an energy efficient way of grinding and a number of operations have utilised this in the design of their comminution circuits. Owing to the large flow of slurry through the mill that results from operating this way the grates and pulp lifters have to be designed to cope. However, the literature has little or no information on how grate and pulp lifter size and design are related to their ability to remove slurry from the mill. Over the last few years the JKMRC has been researching this area and has developed relationships between grate/pulp lifter design and flowrate capacity. At the same time it has determined the major causes of pulp lifter inefficiency and a solution to preventing this inefficiency (the Twin Chamber Pulp Lifter). This paper describes the models that have been developed through this program and uses industrial scale data to illustrate their accuracy. Results from the industrial trials of the Twin Chamber Pulp Lifter are also presented.

Jan 1, 2000

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996

By T. A. Doyle

Column and batch test methods are used to simulate and model the leaching of various mining by-products. Batch tests are simpler, while column tests more intuitively represent the field conditions to be simulated. Projects that have included different types of leaching tests illustrate the strengths, limitations, and associated uncertainties of each. Column and batch tests have been used to evaluate arsenic solubility in leachate from treated copper smelter flue dust, to simulate the leaching of pit wall rock from a proposed gold mine, and to simulate the release of uranium from aquifer materials.

Jan 1, 1998

By D Capstick, M B. Ebell

This paper describes the test work, process design, commissioning and operation of a processing system at the Ergo gold operation that improves the extraction efficiency from gold tailings material. The improvement in recovery is derived from the separation of the gold contained within the sulfides of the tailings material and a dedicated process stream to recover that gold.The sulfides are separated by means of a flotation circuit and that resulting concentrate is subjected to a regrind of below 20 ¦m to enable a greater liberation of the gold. The ultra-fine material is then subjected to a dedicated leach circuit to recover the now exposed gold particles.The case study is an example of the challenges of introducing new technology and methodologies to a well-established operation and thereby attaining improved efficiencies and tangible business benefits.CITATION:Ebell, M B and Capstick, D, 2013. Improving extraction efficiency from Witwatersrand gold tailings using flotation and ultra-fine grinding of concentrates, in Proceedings World Gold 2013 , pp 301-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Katherine A. Margolis

Refuge Chamber Expectations Training was created by a multidisciplinary team at the National Institute for Occupational Safety and Health (NIOSH) to inform miners of what to expect psychologically and physically if it became necessary to use a refuge chamber in a mine emergency. The presentation can be used either for one large group or for individual miners. The training is a multimedia Adobe Flash presentation containing pictures, audio, video, and interviews with miners who have used a refuge chamber in an emergency. It must be run on a computer with Adobe Flash Player installed (refer to the computer system requirements section).

Oct 1, 2009

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By N. Fukatsu

The recent development of galvanic cell-type hydrogen sensor for molten copper was outlined. The principle of the sensing mechanism, the fundamental structure of the sensor, and its performance as a process control device are discussed based on experimental work undertaken by the authors. Besides sensors based on usual perovskite-type proton conducting oxide, those using magnesium-doped alpha alumina, which was recently known as a proton conductor, were investigated and the results at the laboratory scale are reported. Considering the excellent sensitivity at high temperature and the stability to the disturbance from the attendant oxygen activity, magnesium-doped alpha alumina was regarded to be a superior material for the sensors used for such purposes.

Jan 1, 2007

By Sami Kara, Marsel Nabium

As a mining project is developed from conceptual to production phases, there exists a variety of uncertainties and difficulties that affect the operation’s designs and economic values. A notable design parameter to be taken into account is the factor of dilution. Dilution is the waste material not separated from the ore in the stages of mining and is sent to the processing plant. It is defined at the ratio of tonnage waste mined and sent for processing over the combined ore and waste tonnage milled. Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programs require interaction on a multidisciplinary level. This paper outlines recent initiatives undertaken at Polysmetal Silver Magadam Mine to reduce dilution and increase revenue. This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution. The mining companies put a lot of effort into extracting lower grade while minimizing cost. The dilution control assists with achieving this goal. In Polymetal Silver Magadam Mine we succeeded to control more than 20 blasts by keeping almost the same grade measured in the face. The results indicated that using the adequate blasting timing design can help to separate the ore from the adjacent waste in drift blasting with different ore body configuration.

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By John W. Finch

The present epoch in human history has been variously described as the age of coal, of oil, of iron and steel, and of power. All agree, however, that it is a great industrial period. Power is of course the vital force in the industrial organism; but power is derived chiefly from mineral fuels or from harnessed and controlled water - also a mineral substance although usually not so classified by industry. However, the latent energy of fuels cannot work for men until it is changed to active energy by combustion and until this active energy is converted into motion. This motion is just as indispensible as the energy itself. Likewise, the latent energy of water cannot be utilized until it, too, is converted into motion; out the mechanisms and devices for converting latent energy into motion, as well as the structures in which they are operated, would not be possible without metals and other minerals. Consequently, minerals are fundamental in industrial civilization.

Jan 1, 1938

By Robert S. Holmes

The U. S. Army Corps of Engineers Explosive Excavation Research Office (EERO) of Livermore, California, has been engaged in research and development of excavation techniques using both nuclear and conventional explosives since 1962. Prior to July 1971, this organization was designated the U. S. Army Corps of Engineers Nuclear Cratering Group. The EERO mission is performed as part of the joint Atomic Energy Commission -Corps of Engineers nuclear excavation research pro-gram. During the period 1962-1969, the Corps executed many cratering explosions using spherical charges of up to 85 tons of nitromethane to model nuclear excavation concepts and to develop design criteria for the nuclear cratering explosions. The experience gained in these modeling tests suggested that explosive excavation using large chemical explosive charges could be applied to excavation projects as an economical substitute for traditional excavation techniques. Consequently, the Corps' research program was broadened in 1969 to include development of chemical explosive excavation as a construction tool. The term "explosive excavation" denotes the use of large buried explosive charges to produce an excavation by fracturing the material and casting it into a desired configuration. In its simplest form, this technology involves detonation of a single explosive charge buried at the proper depth to produce a crater which is roughly hyperbolic in cross section. The types of craters produced by various depths of burial are illustrated by Figure 1. Single or Multiple rows of charges are used to excavate linear cuts required for water conveyance or navigation channels. .More complex explosive excavations include small craft harbors, railroad and highway cuts, and removal of W1denvater rock barriers to navigation. While the literature indicates widespread use of large explosions in the (1) ERRO is a field activity of the Waterway Experiment Station, Vicksburg, Mississippi

Jan 1, 1971

By D. R. E. Whitmore, J. M. Harrison

There are five logical stages in the search for orebodies in virgin territory, namely: (1) reconnaissance inventory of geology, and related investigations; (2) development of broad concepts as a basis for selecting regions of potential mineral deposits; (3) assessment of criteria leading to specific localities within these regions; (4) geo-physical and geochemical studies that will delineate small anomalous areas; and (5) stripping, drilling or other means of locating ore. In addition, the development of new means of extracting mineral resources and the finding of new uses play a vital role in our mineral industry. The continued growth of this industry will be largely governed by our ability to develop or to adapt new concepts and techniques, and to produce a greater number of scientists and engineers. It should always be remembered that more than one-third of Canada's exports are dependent upon our ability to find, develop and economic-ally exploit new orebodies.

Jan 1, 1967

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013