Search Documents

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By Robert A. Bosschart, Harold O. Seigel

"Most electromagnetic methods presently used in mining exploration are of the moving source type; i.e., the primary field source is moved simultaneously and in a fixed configuration with the receiver. Of the fixed-source methods, which employ a stationary primary field and a moving receiver, the Turam method is the most effective and has marked advantages over alternative electromagnetic methods. The results are little affected by topographic relief, and a high degree of resolution can be obtained because of the constant relation between source field and investigation area. Another inherent advantage of the Turam configuration is that it provides more favourable dimensional relations. Thus, the primary field attenuates at a much lower rate than in moving-source configurations and, secondly, the method is size sensitive; i.e., conductor size affects the strength of the response, which is not the case with moving-source methods. These factors result in a considerably better potential depth penetration."

Jan 1, 1966

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By Youn-Bae Kang

In order to overcome weak points of steel for its engineering applications, in particular, for environmentally benign, energy-efficient, lightweight engineering systems, a number of new steels have been proposed, especially to improve strength-to-weight ratio (specific strength). Mass production of these steels, however, has encountered a serious roadblock particularly in the steel refining and casting processes. This is because their chemistries and cleanliness requirements are vastly different from those of the conventional steels, and thus an incremental improvement of the prevailing process technologies is found hard to meet the requirements. In this study, a new process is proposed, which employs inert gas bubbles in the shroud nozzle, liquid steel drops in the degassing chamber, and the siphon transport for continuous casting. The proposed process which integrates the final refining and cleaning steps prior to casting is expected to be a technologically disruptive innovation on the conventional counterpart. The effectiveness of the individual steps is discussed with experimental results.

By George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond county, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1914, the derrick spans, 2,000 feet or more long, became unwieldy. To overcome this, and also to eliminate hand labour as much as possible, steam shovels and railway haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type.

Jan 1, 1946

By Kimberly Conner-Mills

Due to increasingly stringent worldwide environmental regulations for gaseous, aqueous and solid waste emissions, conventional smelting technology cannot effectively process arsenic containing materials. Many globally significant copper properties have copper sulfide mineralogy that has a high arsenic content present as enargite with significant contained precious metals. As global copper, silver and gold demand increases while significant world resources decrease, treatment of sulfide orebodies with enargite is becoming increasingly important. Methods to selectively dissolve and fix arsenic, leaving behind clean copper and precious metals-bearing concentrates could effectively treat these ores.

By Rubén Alvarado

The markets and environmental protection rules are more and more exacting, both of which have determined that copper smelters should look for technological development and global management to ensure their viability and competitivity in the short and long term. The main facilities of the present and future Smelting-Converting Process at Codelco's Caletones Smelter, is based on Teniente Converter reactors with a high operational availability that have reached concentrate processing capacities near 2,000 tpd. These reactors are in operation in most of the smelters in Chile as well as in Zambia, Peru, Mexico and, in ?the near future, in Thailand. Since 1993, the Smelting-Converting process of the Caletones Smelter of Codelco-Chile has been based on one Reverberatory furnace, two Teniente Converters and four Peirce-Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers, three Slag Cleaning Furnaces, and two Oxygen Plants have allowed the smelter to reach concentrate smelting capacities and copper productions of 1,215 kt/year and 360 kt/year, respectively. This transitional operating scheme, combining together traditional and advanced technological equipment, needs further modernization to successfully face the modern world challenges, especially with relation to the environmental commitment, production costs and wide satisfaction of customers. For this reason, for the period 1997-2000, a Modernization Plan has been worked out. This plan considers an increase of the present throughput, which will permit a significant increase in productivity, as well as finding a definitive solution for meeting the environmental regulations. Among these projects, we can point out the definitive shut down of the Reverberatory Furnace, which is a contaminating piece of equipment of low energetic efficiency. Additionally, it considers the installation of two new Slag Cleaning Furnaces, one additional Oxygen Plant, and the incorporation of two new Sulphuric Acid Plants with a production capacity of 4,500 T/D, that will recover over 92% of the sulphur content, of process off-gases.

Jan 1, 1998

By Ralph L. Rutherford

Geologists or mining engineers familiar with geology are frequently requested by mine operators to give correlation in-formation regarding some mining property with respect to an adjacent area on one at some greater distance. It is the object of this article to mention a few of the difficulties involved in securing this information and to point out some of the salient factors upon which correlation is dependent. In view of the nature of the following discussion, a brief statement of the general character of coal formations .. seems appropriate. Coal formations, by reason of their environment of deposition which is in fresh or brackish water, exhibit the features common to continental deposits, in contrast to those of marine deposits. Such deposits are characterized by rapid variation in thickness and in lithological character both later-ally and vertically. (Plate 1 A). They consist essentially of sandstones and clay shales with all gradations between them, and also a few beds of coal and frequently some conglomerates.

Jan 1, 1924

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By Catherine T. Aimone-Martin, Meyers Joseph A.

A new strain-based criteria is being adopted for rock blasting in New York City (NYC). This criteria is based on several years of research involving vibration measurements of tall structures during blasting within several feet from buildings designated historic and Landmarked. This research has demonstrated that tall, heavy structures show little upper-structure vibratory response during hard-rock, urban blasting carried out in NYC. The Fire Department of New York City (FDNY) permits rock blasting and regulated limits for ground vibrations using the U.S. Bureau of Mines (USBM) safe blasting criteria. However, these regulations are often superseded by a 0.5 in/s (12.7 mm/s) limit imposed by the New York City Department of Buildings for historic and Landmarked buildings that are adjacent to the majority of blasting projects in the City. This onerous limit is often exceeded resulting in frequent stop work orders that increase the cost and time of rock excavation projects. The

Jan 1, 2019

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By S E. Wallah, D Hardjito, B V. Ran

The manufacture of Ordinary Portland Cement (OPC) is not only energy-intensive but also releases a significant volume of carbon dioxide (CO2) to the atmosphere. In addition, OPC in concrete often causes premature deterioration that affects the durability of concrete structures. This paper explores an alternative to OPC concrete called geopolymer concrete.The present research utilises low calcium (class F) fly ash as the source material to produce geopolymer concrete. Several factors that affect the mix design process such as mix proportion, curing time, and curing temperature have been studied. In addition, the long-term properties such as drying shrinkage, creep, and exposure to sulfate attack are also being investigated.The test data presented in this paper reveal that geopolymer concrete possesses high compressive strength, undergoes very little drying shrinkage and moderately low creep, and shows excellent resistance to sulfate attack. The result is extremely promising and demonstrates the sustainability of geopolymer concrete as a construction material for a sustainable future.

Jan 1, 2004

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By Jaeheon Lee, Junmo Ahn, Doyun Shin

"Many alternative leaching systems including bacterial leaching have been introduced to avoid passivation on the surface of chalcopyrite and to increase the leaching efficiency of copper from chalcopyrite. Recently, glycine, one of the simplest amino acids, has been emerging as an efficient and environmental-friendly lixiviant to recover copper. In the present study, an alkaline glycine–peroxide lixiviant system was used to leach copper from chalcopyrite concentrate and the leaching mechanisms were also investigated by a suite of kinetic studies under different conditions. The chalcopyrite concentrate contains 28.8% copper with 30.8% sulfide sulfur. The effect of concentration of glycine and hydrogen peroxide of the leaching solution was investigated. Glycine concentration was varied from 0.5 to 1.0 M and the hydrogen peroxide concentration was changed between 3 to 5%. Leaching time and pulp density were also varied. Hydrogen peroxide is an oxidant of the system and the leaching efficiency with periodic additions of the peroxide was also studied. A mineralogical study was performed using XRD and SEM. To investigate the surface of the residue materials, XPS was used to see if any passivating layer was formed during the leaching. Detailed results from mineralogical, chemical, and metallurgical studies will be presented and discussed.INTRODUCTION The greatest global resource of copper is low-grade chalcopyrite and heap bioleaching may be the only economic option for its processing. However, formation of a passivating layer on the surface of chalcopyrite slows down the oxidation reaction and reduces the efficiency of the process."

Jan 1, 2017

By S. Mondon

Hibi Smelter which is a Copper Smelter lining a blast furnace, produces 2,700 metric tons of anode copper per month. Generally, in a copper refinery, arsenic and antimony are considerably troublesome impurities. With regard to the elimination of antimony, Hibi Smelter has two handicaps described as follows. (1) Smelting under the slightly oxidizing atmosphere in the blast furnace. (2) Recycling the converter slag to the blast furnace after cooling. Therefore antimony and arsenic, mainly antimony, elimination tests, in which the alkaline flux was injected through the two tuyeres in the blowing stage, were carried out in the rotary anode furnace. Antimony and arsenic were respectively removed more than 90 96 from the molten copper, and their high eliminations are discussed by application of the transitory and permanent reaction model with the flux injection, which was presented by T. Lehner.

Jan 1, 1983

By F Wu, H Wang, W Chen

A pressurisation method with multiparallel fans has been adopted at HongLiuLin Coalmine to control the significant external air leakage through the goaf area of coalface 15207. Potential damaging effects of large external air leakage on a coalmine’s ventilation system are analysed according to the current air leakage status caused by the exploitation of shallow-covered coal seams. The use of pressure balanced ventilation to prevent external air leakage through goaf areas is introduced. The calculation of ventilation network of HongLiuLin Coalmine shows that the air resistance of an external air leakage branch through a goaf area and the air pressure drops from the intake slope to the working face can be adopted to determine the values of pressure to be increased by regulating fans and airflow controlling parameters of regulators. By investigating airflow requirements of the pressure-balanced area as well as the performances of the auxiliary fans currently used in the coalmine, the number of pressurisation fans needed is fixed. The expected result is achieved after the pressurisation method has been carried out, which can be helpful for other coalmines to handle similar problems.CITATION:Wu, F, Chen, W and Wang, H, 2015. Multiparallel fan method to prevent significant external air leakages through a goaf area of a shallow covered coalmine, in Proceedings The Australian Mine Ventilation Conference, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"Drill and blast represent the most important, and sometimes the costliest processes in the mine. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum and Temeng, 2015). The use of available information to improve the drill and blast processes can be the difference between a wasteful process and one that is optimized for costs, safety and desired fragmentation. Mining operations have access to several types of data sets that include a variety of different systems. This information can be used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the drill and blast process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting across multiple sites, it becomes valuable to create auditable, automated and sustainable workflows for handling the information.In some cases, the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Wixom, Watson, 2007). The author’s initial implementation plan for the drill and blast solution included using data stored at the sites on local servers. However, we learned early in the process that much of the work for aggregating and supplying the required data was already completed and was available in the EDW ready for use. This saved time, reduced risk and added value to the system.The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, especially highlighting the value of using an EDW for managing drill blast information; and to discuss how technical challenges encountered during the implementations were resolved. This article targets users that want to better manage their drill and blast data or try to set up standardized workflows for using this information.This case study will discuss the process of implementing a drill-and-blast workflow at multiple sites within Freeport-McMoRan (FMI) using both data at the sites and information available from the EDW."

Jan 5, 2017

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

"Hematite pellets were electro-deoxidized to iron in molten sodium hydroxide to produce iron containing about 10-wt % oxygen. The anodic reaction was the evolution of oxygen on an inert nickel anode. Before the electrochemical reaction, there is a reaction between sodium hydroxide and ferric oxide to form sodium ferrite and, in order to compensate for the reduction in sodium oxide content, 1 wt % sodium oxide is added to the melt. In a laboratory cell, the cell voltage was 1.7 V with a current density of 5000 A m-2, a current efficiency of 90% and an energy consumption of 2.8 kWh kg-1.Introduction The iron and steel industry contributes about 2.3 bn tonnes/annum of the carbon dioxide to the atmosphere, which is about 10% of the total, and some believe that, in order to prevent a catastrophic rise in the earth’s temperature, carbon dioxide emissions must be reduced by 50% come 2050. However, by 2050, it is likely that the iron and steel industry would have grown significantly so that the production may have risen to 2 or 3 bn tonnes/year so in order to meet the 50 % reduction on today’s figure, the carbon dioxide may have to be reduced to 25% or less, which is a very demanding requirement. There are probably three ways of reducing the carbon dioxide output:1. By capture and sequestration, but this may be technically very demanding.2. Reduction using hydrogen in place of carbon."

Jan 1, 2009

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998