Search Documents

By Muhammad Azeem Raza, Muhammad Zaka Emad, Muhammad Usman Tahir, Saqib Ahmad Saki, Muhammad Usman Khan

Shotcrete is a key initial rock support component used in underground mining and civil projects. The strength of shotcrete plays a vital role in providing and deciding the support adequacy. The strength of shotcrete is evaluated by its uniaxial compressive strength (UCS) test that is usually conducted on extracted core samples. Shotcrete cores are commonly extracted from the test panels along the direction of its application; thus, its strength perpendicular to the direction of application is often neglected. The true bearing strength of shotcrete is thereby ignored despite the fact that higher stresses act normal to the direction of its application. Although the anisotropic behavior of shotcrete is well reported, no study has reported extensive testing of this scale and nature. This study reports extensive testing of shotcrete cores extracted from tunnels of a mega hydroelectric project in Pakistan. The study reports 7- and 28-days strength tests of shotcrete cores. The research also investigates the anisotropic behavior of steel fiber reinforced shotcrete and suggests that shotcrete exhibits higher strength perpendicular to the direction of its application.

Dec 26, 2022

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By P B. Hills

This paper discusses the computerisation of the drill hole database, some historical records and the creation of a three-dimensional model of the gold bearing structures for resource estimation and mine design at the Beaconsfield Gold Mine in northern Tasmania. The phase of the work reported here commenced in November 1997 and was completed in March 1998. The historical mining on the Tasmania Reef had reached a depth of 450 m below surface when work ceased in 1914. Production up to this time was 854 000 ounces gold. Recent activity has concentrated on testing depth extensions of the previously mined ore structure, to a depth of 1000 m below surface, and the establishment of an underground mining operation to exploit this resource. The lode structure at Beaconsfield is a typical mesothermal vein style deposit. Gold is contained within narrow quartz, carbonate and minor sulphide reefs or veins. Reef width is variable from a few centimetres to several metres with æsplitsÆ or bifurcations being common. The reef averages 2.7 m true width in the economic zones. The key feature of this style of mineralisation is that reef continuity can be confirmed by drilling to a high level of confidence, but the gold grades are somewhat more erratic in nature. The resource estimates were based entirely on drill data. The drill intercepts on the reef were coded for each split directly into a database and these allocations validated graphically. The distribution of grades and widths show an increasing gold grade with reef width for both the drill hole and historical data. The same histogram patterns, mixed populations and overall arithmetic average grade for the historical mine (at 21.52 g/t > 3 g/t Au) and new drill data (at 21.55 g/t > 3 g/t Au) would indicate that there has been no major change in the overall style or grade of the ore from the historically mined areas to the new resource. The reef, host geology, area of historical workings and resource zones at the Beaconsfield Mine were defined as a series of closed wireframes. The Tasmania Reef was modelled as five mutually exclusive wireframes, one each for the Main Reef, Footwall split, Second footwall split, Third footwall split and Hangingwall split. The data for this exercise was extracted directly from the drill hole database, stored in Microsoft Access format. The formation of the solids was largely automated with manual validation and refinements allowing for multiple runs using different interpolation methods and combinations of drill holes. A rotated 3D-block model in the plane of the Tasmania Reef was created to contain the grade model and allow for tonnage, grade and reef width estimates. An inverse distance squared (ID2) interpolation method was used with ranges of 25 m along strike and 125 m down plunge with blank areas infilled with 50 m by 250 m. Each reef split was filled separately using only drill intercepts from that split. The method was independently validated used MIK methods. Longitudinal sections have been prepared showing gold grade, reef width and width +grade. Estimates were also made for arsenic, sulphur and other minor elements. The long sections show three distinct mining zones. A method is presented for the conversion of the resources to reserves by the addition of mining parameters for minimum mining width, minimum pillar, cut-off grade and internal and external dilution. The selection is done on columns within the block model, and allows for all splits to be considered at once. Multiple runs can be made for varying combinations of parameters to test different mining methods and their impact on reserves, mine life and NPV.

Jan 1, 1999

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By V. C. Allen

THE Tri-State Zinc, Inc., Galena, Ill., was confronted with the problem of securing ore from a deposit because the hoisting shaft was several thousand feet from the mill. The orebody is several thousand feet long, averaging 200 ft in width and 60 ft in height and opened up by vertical shafts some 300 ft deep. Mining is by the room-and-pillar method. During the initial operation the ore was loaded by conventional electric 1/2-yd boom-and-dipper shovels and hauled to the shaft by 8-ton diesel trucks. This underground ore loading and hauling was well adapted to the conditions and productive of low costs per ton. However, with the mill situated as mentioned, a triple handling of all broken rock was necessary: l—from the stope to the shaft by truck, 2—up the shaft by skip br can into the surface hopper, and 3—by truck from the surface hopper to the crushing plant at the mill. In addition to the repeated handling, serious troubles were encountered during the winter because of freezing in the shaft hopper. Consideration was given to either moving the mill to the new orebody or to the construction of a second mill. The presence of other orebodies to be mined at a later date made the first alternative impractical while the capital outlay for a second mill, when the present plant of approximately 850 tons per day was deemed sufficiently large for the total reserves, made the second alternative also unwise. It was decided to retain the mill in the originals location and continue to move the ore to it. The idea of driving an inclined adit from the surface to the bottom of the orebody suitable for truck haulage and big enough to allow the passage of all mechanical equipment was conceived. Among the apparent advantages of such an incline were: 1— Direct haulage from the stope to the mill without rehandling. 2—Elimination of virtually all grizzlies. Trucking from underground to the mill would do away with all hoppers, chutes, gates, and skips and make the maximum rock size dependent solely on the size of the shovel dipper at the mine and the crusher opening at the mill. 3—Less secondary blasting would be needed. 4—Ease of transporting equipment and supplies underground. Shovels and trucks could be taken through the incline intact. 5—Equipment could be brought to the surface for repairs and servicing without loss of time. The same advantages of ease in moving would be present in the handling of men, steel, powder, and supplies. 6—There would be far less difficulty in increasing the amount of tonnage that could be moved by truck up an incline than would be found in attempting to increase the capacity of a shaft. 7—All the broken ore in the stopes would serve as bin capacity, as it would take the breakdown of all of the loading and hauling equipment to have the same effect as a delay in shaft hoisting. 8—All danger of men being trapped in the mine as a result of shaft fire or power stoppage would be eliminated. 9— Virtually all trouble from severe winter conditions would be eliminated by the direct haul underground to the mill. The decision was made to proceed with the driving of an inclined adit. The topography of the surface between the orebody and the mill was such that it was possible to locate the portal at a point 170 ft above the mine floor and 1800 ft horizontally from the central point of the orebody to the south and 2500 ft from the mill to the north. A grade of 10 pct was found to be optimum for continuous truck haulage when the various factors of speed, safety, and truck maintenance were all considered. The incline as driven was consequently 1700 ft long on 10 pct grade and 12 ft high by 17 ft wide in cross section. The tunnel-driving equipment was chosen so that it could be used in mining after the completion of the tunnel. Drilling was done with a jumbo with two Joy jibs mounting 3-in. drills, loading with an Allis-Chalmers diesel-powered, front-end loader of approximately 11/4-yd capacity, and hauling by Koehring Dumptor trucks of 8-ton capacity, diesel-powered. The width of the tunnel allowed the end loader and Dumptor to be placed abreast. Since the Dumptors can be driven either forward or backward with equal facility, loading was accomplished without turning around either machine throughout the loading operation. The crew in addition to the tunnel foreman was comprised of three men per shift at the start and in the later work, four men. Each crew could perform any part of the working cycle. If the drilling was completed and the round blasted in the middle of a shift, the same men would proceed with the loading and hauling. Since the mine already had been drained to the bottom levels, no water was encountered. At the halfway point the tunnel was widened for approximately 100 ft to permit trucks to pass. The total cost of the tunnel excluding the capital outlay for equipment, which was all continued in use in the subsequent mine operation, was $60,363.00 or $35.50 per ft. The tunnel was completed at the end of June, 1949 and has been in continuous use since that time. In the five months from July to November inclusive, 106,049 tons have been transported to the mill or an average of 835 tons per day. No unforeseen disadvantages have been encountered and the advantages which had been predicated before the adit's construction have been more than realized. As previously mentioned, the deposit is worked by the room-and-pillar system with occasional faces up to 125 ft high. Except in driving development drifts when diesel-powered, front-end loaders such as were used in the tunnel are employed, all shoveling is done by Yz-yd boom-dipper type shovels electrically driven. These units need a width of 25 ft and a height of 14 ft in which to operate. All hauling is by diesel trucks, mainly Koehring Dump-tors. Roads are maintained with caterpillar tractors and a road grader. The tonnage output from the

Jan 1, 1952

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By K. Malysa

Bubble collisions with ore grains and a selective formation of the bubble-grain aggregates are necessary steps for flotation separation of useful and gangue components of an ore. For the attachment of valuable mineral grain to the colliding bubble a liquid film, separating the bubble and the grain needs to rupture during short time of their collision. High hydrophobicity of the grain surface is favorable because stability of the separating (wetting) film is much lower at such surfaces, that is, the film ruptures faster and at greater thickness. Simultaneously, it needs to be kept in mind and taken into consideration that high affinity to air is a typical feature of hydrophobic surfaces. Thus, when the hydrophobic surface is immersed into aqueous phase the air can stay attached to such surfaces and affect kinetics of the bubble attachment. The paper presents results and analysis of dynamic phenomena occurring upon the collision of the rising bubble followed by its attachment to hydrophobic (Teflon) plates of different roughness. The influence of the Teflon surface roughness, solution concentration, bubble size and impact velocity on bouncing of the colliding bubble, time of the three phase contact (TPC) formation and drainage time of the liquid film, formed between the solid and bubble surfaces, is described. High hydrophobicity, as showed earlier (Malysa et al, 2005), does not assure that each collision leads to the TPC formation and attachment of the colliding bubble. Roughness is the parameter of crucial importance for kinetics of the bubble attachment to hydrophobic surfaces (Krasowska and Malysa, 2007; Krasowska et al, 2009; Kosior et al, 2011). Enlarged roughness of the Teflon plate, from ca. 1 to 80µm, results in shortening the time of the TPC formation (bubble attachment) by over an order of magnitude - from 105 to a few milliseconds only. Higher surface roughness means that larger amount of air can be entrapped in bigger scratches and cavities of the Teflon plate during its immersion into aqueous phase. Results documenting importance of the air presence are showed and mechanism of the air facilitated TPC formation and bubble attachment to hydrophobic surfaces is described. Keywords: bubble collisions, hydrophobic surfaces, teflon plate roughness, TPC formation

Sep 1, 2012

By R. W. Lowe

1. Reserves are estimated in the Nemo, Sewanee, Wilder, and White Oak beds of Fentress County, Tenn. The Wilder is the only bed being mined commercially and contains the largest known reserves. Eleven lesser known beds are present in the county, but not enough information on them was available for estimating the reserves. 2. Known measured and indicated reserves, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 102 million tons as of January 1, 1955. This total includes 66 million tons in beds 28 inches and more thick.

Jan 1, 1956

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By D. Weston

During recent years there has been a great deal of confusion in the North American mining industry with the introduction of new comminution terminology and claims (without substantiative evidence), for various types of equipment in this field. The authors will attempt to clarify the terminology used, and where possible, give illustrations of plant practice with actual operational and pilot plant data. This is considered necessary in order to obtain a clear picture of the comparison of such equipment to the revolutionary change that the Aerofall Mill has brought to the mining industry.

Jan 1, 1964

[1.1. The provisions of this code are minimum provisions and are designed to minimize hazards to life and property in and about underground coal mines where electrical equipment and circuits installed used. They indicate the Steps necessary in the selection, installation, operation, inspection, and maintenance of electrical equipment and circuits to obtain proper safeguards in reducing electric shock, fire, explosion and other hazards. Surface as well as underground installations were considered in formulating the code and, unless otherwise stated, each provision applies equal to both underground and surface installations. This code does not apply to buildings and installations not directly connected with mining operations, nor does apply to strip-mining operations.]

Jan 1, 1952

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defence for purposes other than the extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallic is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of the Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

By Ogden Tweto

The Leadville district, on the west flank of the Mosquito Range in central Colorado, has produced silver, zinc, lead, gold, and minor metals valued at $512,000,000. The ore deposits are in a sequence of dolomites and quartzites, Cambrian through Mississippian in age and about 500 feet thick, which is extensively intruded by porphyry sills, dikes, and plugs of Tertiary age. The sedimentary rocks and sills dip about 15°E and are broken by many faults, which are predominantly of nearnorth trend and downthrown to the west. The ore deposits are principally blanket or manto replacement deposits, but in the eastern part of the district many veins occur also. The replacement deposits are largely confined to three dolomite units in the stratigraphic sequence. Of these, the uppermost or Leadville Dolomite is the most productive. Most ore bodies are on the underside of porphyry sills and, particularly, beneath sills that occupy unconformities. Many replacement bodies have vein roots or branch from veins. The veins occupy faults and are productive mainly in the section of quartzites and dolomites and included sills. The primary ores consist principally of pyrite, marmatitic sphalerite, and galena but locally contain chalcopyrite, silver minerals, bismuth minerals, and gold. Principal gangue minerals are manganosiderite and jasperoid. The ore deposits have a crude zonal pattern centered around an intrusive center at Breece Hill, which evidently influenced ore deposition thermally. The ore deposits were oxidized to depths of several hundred feet in Miocene time. Bonanza ores mined in the early days were characterized by cerussite, cerargyrite, and embolite. Later, zinc carbonate ores were identified and mined on a large scale. The Leadville district is a complexly faulted and intruded area at the intersection of major fault systems trending N20°W and N15°E in the Mosquito Range. The intensely fractured area evidently localized igneous intrusion and subsequent mineralization. Ore solutions rose on many of the faults in the area, presumably from the same source as the porphyry magmas. Movement on these faults continued into the Pleistocene, displacing ore bodies, oxidation zones, Pliocene sediments, and glacial deposits.

Jan 1, 1968

In this U.S. Bureau of Mines report, in situ vat leach mineral recovery system concepts are described and cost compared with conventional mining and pad and autoclave leach processing systems. In the proposed systems, leachable ores are enclosed in place in reagent-impermeable in situ vat constructions. The ores are then rubbled and flood leached or flood oxidized and leached. The in situ vats are called stope leach or stope autoclave vessels. The report also proposes ore body-adjacent in situ vat constructions containing rechargeable processing stopes. A series of ore body-specific, innovative, and conventional mineral recovery systems case study designs are described and prefeasibility level costed. Based on a comparison of these prefeasibility level cost estimates, the proposed systems are determined to be economically competitive with conventional min¬eral recovery systems. The in situ vat leach mineral recovery systems concepts for leachable and refractory ores are developed around the drill-split narrow-vein and longwall mining methods described in part 1 of this Information Circular series.

Jan 1, 1995

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By Harlan A. Walker

This paper on the mines of El Potosi Mining Co. is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Grateful acknowledgment is made of the helpful suggestions and criticisms offered by the management, together with the assistance of the mining staff in preparing maps and drawings and of C. L. Thornburg, mine geologist, in preparing the section on geology.

Jan 1, 1934

By J. P. Powell

The application of secondary producing methods for recovering additional oil from known fields has been recognized for many years as important to the economy of the nation. One of the most successful secondary methods is waterflooding, which conserves our natural resources by preventing premature abandoment of stripper leases and revitalizing previously abandoned areas. Waterflooding as a secondary-recovery method was introduced into the Midcontinent region in 1931, and its use as such has become widespread. As with most new methods, the most favorable fields and leases received primary attention, whereas those with viscous oil or less favorable sand characteristics were bypassed. Numerous reports3 4 5 6/ have been published giving the results of individual waterflooding projects, In this report, attention is directed to the effect of a single factor, the viscosity of the oil produced,

Jan 1, 1959

By Gennaro G. Marino

This paper summarizes and evaluates data on mine subsidence ground movements and associated damage for houses in Illinois. Based on the data collected, the response of homes to subsidence ground movements is expressed in terms of repair costs. A damage criteria is then proposed that relates the ground movements and damage levels. The data were collected as part of a comprehen¬sive study performed for the Illinois Abandoned ?Lined Lands Reclamation Council, A -M-RC, by the Civil Engineering Department at the University of Illinois, and probably will be published in late 1934 by the council. The study concentrated its efforts on surface ground movements and the effects to houses over abandoned room and pillar mines. The resultant surface subsidences are commonly dish or bowl shaped and are termed sags. Method of Analysis The steps in analysis used to arrive at the proposed damage criteria are: 1. Canvas and rap subsidence damage in houses, 2. Assess the associated ground movements, 3. Estimate the damage repair cost, 4. Develop a damage/repair level classifica¬tion, 5. Correlate the associated ground movement, damage/repair level and home construction type, 6. Propose a damage criteria.

Jan 1, 1984

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984