Search Documents

By Frederic P. Dewey

THE Bureau of the Mint of the United States Treasury maintains 13 offices for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, eight tables of comparative results, taken from the regular work of the service, are given. These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement. in the assay-results, and follow through decreasing gold fineness and . increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the' agreement of the assay-results; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these are added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion2 I

Aug 1, 1909

By Florence L. Feicht, H. H. Schrenk, Carlton E. Brown

This report describes the dropping - mercury electrode , its use in analysis , and the procedure of the Health Division of the Bureau of Mines in determining lead , cadmium , and zinc . The dropping - mercury electrode or polarograph is an electrolytic device , one electrode of which consists of mercury issuing in small drops from a capillary tube . Such electrodes have been in existence for more than 50 years, but they were not used for analytical purposes until about 1922.6/ Developments since have been rapid , especially in Czechoslovakia , Germany , Italy, and Japan and more recently in the United States . A recent bibliography / contains references to, 825 articles issued from 1903 through 1940. In 1939 Kolthoff and Lingane presented the first comprehensive critical review, in English , of the device and its use in analysis . They have recently issued a book on the same subject. Similar information also is included in a recent book10/ by Kolthoff and Laitinen . Much of the information in this and the two following sections on this device and its use in analysis was obtained from these three publications . The use of the dropping - mercury electrode in analysis is based upon the fact that the kind and amount of electro - reducible and electro - oxidizable constituents in solution can be determined from the current -voltage relationships revealed by this electrode or electrolytic device .

May 1, 1942

By Jianbo Hu, Tao Zheng, Zhao Qihua, Rui Su

Rock mass discontinuities play a significant role in evaluating the stability of rock slopes. It is necessary to collect and analyze these discontinuities to fully understand the mechanical and deformational behaviors of rock masses. Based on the digital images of some slope faces, this paper proposes a framework based on machine learning for detecting and extracting discontinuities. First, digital images and photo poses are combined, the original scene is reconstructed, and 3D point cloud data are obtained. All captured point clouds can be mapped with each image by the direct linear transformation algorithm. Next, the detection machine learning algorithm is used to segment rock mass discontinuities on 2D digital images. Finally, based on the mapping relationship, the 2D digital images that were segmented are transformed into 3D point cloud data. The geometric parameters of the corresponding discontinuities can be extracted by the DBSCAN and the Skmeans algorithm and the characterization of specific rules. The proposed framework was evaluated utilizing a quantity of slope digital images in the Yebatan hydropower under construction, located in Sichuan Province, China, as a case study. The results illustrate that most deviations are less than 10° for the dip direction and dip angle, which verifies the reliability of the proposed framework and maintains acceptable measurement accuracy.

Nov 6, 2022

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By S Norman

The Water Delivery Alliance (WDA) was established to design, construct and commission the pump station and desalinated water delivery pipeline to link the desalination plant on the Kurnell Peninsula (constructed by others) with the existing distribution network at Erskineville, Sydney, Australia. The WDA consisted of McConnell Dowell Corporation Ltd (Macdow), Bovis Lend Lease Pty Ltd (BLL), Kellogg Brown and Root Pty Ltd (KBR), Worleyparsons Ltd (WOR), Environmental Resources Management Group Inc (ERM) and Sydney Water Corporation (SWC).Sydney’s Desalination Project is one of the initiatives to secure Sydney’s water supply against the effects of climate change, population growth and drought. The desalination plant, 100 per cent powered by renewable energy, can supply up to 250 million litres of water per day (mld), which is up to 15 per cent of Sydney’s water needs. The project involved the construction of an 18 km pipeline with an ultimate capacity of 500 mld to accommodate any future increase in the output of the desalination plant.The Alliance procured three full-face tunnel boring machines (TBM) from Herrenknecht AG to construct the 6.5 km of tunnel that would provide a conduit for the DN1800 welded mild steel cement mortar lined (MSCL) pipeline at a number of locations along the route. Nineteen shafts and 16 tunnels were required to complete this work.Crucially one of the TBM drives involved construction of a tunnel into Botany Bay under protected marine life habitats; enabling the connection of the MSCL water carrier pipeline into the dredged section of pipeline underwater, approximately 800 m off-shore in Botany Bay.This paper details the retrieval of the 17.4 m long TBM from the ocean floor upon completion of the Botany Bay tunnel allowing for subsequent use on the Project. Elements covered in the paper include the 835 m tunnel, design and construction techniques for the tunnel and recovery, and details of the methods used to install the DN1800 water carrier pipeline.

Mar 8, 2011

By L L. Kuhar

The AMIRA International P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project is an interdisciplinary research collaboration between 17 global mineral companies and four research organisations aimed at providing support for the emerging industry trend of geometallurgy. The main aim of the project is to develop predictive geometallurgical indices which can be incorporated into a resource block model to maximise the commercial value of an orebody and to minimise the social and environmental impact of mining operations.Researchers at the Parker Centre/CSIRO have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. The focus of the small-scale leach tests has been to determine the leach index (relative indication of leach performance), recovery, impurity deportment, reagent consumption, effect of size/degree of liberation and mineralogy of samples for their relative ranking. Predictive tests for heap leach hydrology (related to agglomerate characteristics) and slurry rheological behaviour are also being developed.

Sep 5, 2011

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By Sufi Md Gulzar, L B. Roy

Rock engineering tasks like tunnelling, dam and building construction, and rock slope stability rely heavily on properly estimating the rock’s uniaxial compressive strength (UCS), a crucial rock geomechanical characteristic. As high-quality specimen are not always possible, scientists often estimate UCS indirectly. The primary objective of this paper is to assess the efficacy of long short-term memory (LSTM), K-nearest neighbour (KNN), a combination of particle swarm optimisation (PSO) with an artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) to estimate the UCS of sandstones from Jharia, Dhanbad, India. Point load index (PLI), porosity (n), P-wave velocity (Vp), density (ρ), and moisture content (%) are the parameters used for the present study. Finally, a comparison was made between the various prediction algorithms outputs. The findings of the study validated the effectiveness of computational intelligence methods in forecasting UCS compared to other models used in this paper. The KNN achieves overall the best results, with an R2 of 0.95 for training, 0.94 for testing, and an RMSE of 0.03 for training and 0.05 for testing.

Nov 23, 2023

By M. Hao, L. Wang, Y. Yin, B. Yang

This study established a coupled fluid-electromagnetic numerical model to systematically analyzse the effects of molten steel flow, inclusion transport, and temperature gradients on refractory erosion behaviour within an induction-heated tundish. The results demonstrate that increased induction heating power significantly exacerbates both flow-induced erosion and magneto-thermal corrosion of the refractory lining in the channel region. The erosion rate exhibits a linear increase with power, while the wear coefficient follows a power-law relationship. Concurrently, a higher power level intensifies the inclusion collision source term by a factor of ten, substantially promoting inclusion collision, growth, and removal (increasing the removal rate by 14.86%). However, this also leads to a 51.3% reduction in the outlet inclusion particle size. This research provides a quantitative basis for balancing metallurgical benefits (temperature control and improved steel cleanliness) with the longevity-oriented design of refractory linings.

May 8, 2026

By T. E. Watkins, M. D. Nelson

A method of determining the lime content of drilling muds proposed by Battle and Chaney* has been examined both in the Field Research Laboratories of Magnolia Petroleum Co. and in field drilling operations. This proposed analytical method is condensed as follows: Titrate one ml of mud and one ml of mud filtrate, each with 0.02 N H2SO4, to the end point with phenolphthalein. The volume of acid in ml required for the mud titration is recorded as Pm and that of the mud filtrate titration as Pf Calculation of the lb lime/bbl mud is accomplished by use of the formula, lb lime/bbl mud = 0.6 (Pm - 1.3Pf) - 0.6 The analytical procedure outlined by Battle and Chaney was found to be quite satisfactory when reasonable precautions are used in mud sampling technique. Calculation of lime concentration by the method proposed in the above publication, however, has given values that varied as much as 100 per cent from the known lime content, for muds of either high or low solids concentration. By use of a formula, lb lime/bbl mud = 0.26 (Pm-F1.Pf), based on chemical equivalents of acid required for titration, both laboratory and field data have been satisfactorily correlated with the known amounts of lime present in the muds. In this formula a correction, F1, or volume fraction of liquid in the mud, is made for the solid content of the mud. Pm and Pf * Paper on "Lime Base Muds," presented by J. L. Battle (Humble Oil and Refining Co., Houston, Tex., and P. E. Chaney (Sun Oil Co., Beaumont Tex.), at the 1949 Spring Meeting of the Southwestern District API Division of Production, Dallas, Tex. The analytical procedure has also had wide distribution in a trade journal, Kembreak, published by the Accuracy Rig and Tool Co., Houston, Tex, †Derivation of equation lb/bbl — grams/350 ml 1 ml 0,02 N acid = 0.000741 grams of lime 1 ml 0.02 N acid/ml lime suspension = 0.26 lb of lime bbl lb of lime/bbl = 0.26 (Pm -F1, Pf ) have the same significance as in the Battle and Chaney equation. Table I shows typical data employing both formulas in calculating the lime content of various lime muds. This suggested procedure ignores lime which is in solution in the mud. The solubility of lime in water, normally about 0.5 lb per bbl, is greatly decreased by the addition of caustic soda, and, in a lime mud, it is probable that the concentration of dissolved lime is of the order of 0.1 lb per bbl. Such an amount of lime can be ignored, since it is within the range of accuracy of the method.

Jan 1, 1950

By Jorge Cardenas, Diego Sanchez

Maximizing SAG mill throughput and metallurgical recovery in hard rock operations requires achieving target fragmentation, particularly a sufficient proportion of fines (<25.4 mm). These fines thresholds are strongly influenced by rock mass competency, commonly characterized using the Axb parameter (30–70) from the JK Drop Weight Test. In many operations, conventional blasting designs and standard emulsions fail to generate the fines content required for efficient downstream comminution. This study evaluates several advanced blasting strategies aimed at enhancing fines generation in very competent rock masses while maintaining cost-effective drill and blast performance. The first approach focuses on steadily increasing the powder factor (kg/t) as a core strategy, complemented by adjustments in blasthole diameter, reduced burden and spacing, the use of dual initiation points, short inter-hole delays (<25 ms), and optimized sequencing—all aimed at enhancing energy distribution and maximizing fines generation in highly competent rock masses. The second strategy consists of increasing the energy factor (kJ/t) by selecting explosives with higher energetic content and detonation performance. This includes the use of heavy ANFO blends and ultra high-energy emulsions with aluminum-based formulations, achieving Relative Bulk Strength (RBS) values between 180–190 and up to 210–230, respectively. These products offer higher detonation velocity (VOD) and peak pressure, enhancing shock energy transmission and breakage efficiency. Field results in granodioritic porphyries with high uniaxial compressive strength showed a 3–5% increase in fines generation compared to standard emulsions—contributing directly to meeting mill performance targets in high Axb conditions. Combined, these strategies provide a practical and technically validated pathway to achieving fines generation targets required for optimal mill performance. When matched to site-specific rock mass characteristics and integrated with blast monitoring tools, they enable improved fragmentation control, reduced P80, and enhanced plant throughput—without compromising operational efficiency or increasing costs disproportionately

Jan 26, 2026

By Frederick W. Horton

With large deposits of low-grade molybdenum ore and a latent market for molybdenum, which with development might perhaps equal that for tungsten, the United States has for years made no pro- duction of molybdenum ore worthy of mention. In fact, during the decade previous to 1914, there was no output of molybdenum ore in this country except in 1905, 1906, and 1907, when a few small lots of molybdenite and wulfenite were marketed." To ascertain why this possible source of economic wealth should remain undeveloped, the United States Bureau of Mines undertook an investigation in 1914, with a view of assisting the establishment of a molybdenum industry in this country. A preliminary review of the situation showed the following conditions: Briefly there was a lack of any considerable demand for molyb- denum for the one known use that might consume any large tonnage of it, that is, for the manufacture to certain alloy steels to which molybdenum imparts properties roughly similar to those produced by tungsten. It was at once evident that the market for molybdenum in alloy steels must be developed, or that extensive new uses for the metal must be created, before the demand would be sufficient to war- rant any extensive mining of molybdenum ore. Investigation showed that one of the chief factors in retarding the development of any demand for molybdenum by the alloy-steel trade was that manufacturers who might use, or might investigate the possibilities of using, the metal were kept out of the market by the fear of not being able to obtain steady supplies. On the other hand, those who might be interested in the development of some of the extensive low-grade molybdenite or wulfenite deposits in this country were prevented from doing so by the small visible demand and the fear that any large production would glut the market. Owing to these conditions the mining of molybdenum has in the past been confined almost entirely to small-scale operations on high-grade streaks of molybdenite ore, and the methods of recovery have been limited largely to cobbing and hand picking.

Jan 1, 1916

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By Henry S. Drinker

(Canal Zone Meeting, November, 1910.) FEW men reach middle life without having had the experience of failure in one or more undertakings; and most of us can look back with gratitude to help or advice given us by friends at critical periods of our lives. If, as men, we ask and take the benefit of such aid, why should we expect our sons to be stronger? A parent can make no greater mistake than to send a boy, however steady and intelligent he may be, off&apos; to school or college, and expect the boy always to cope successfully with all the new conditions and new difficulties that may confront him. This is undoubtedly more the case with a freshman, in his first year at college, than in later years, or than it is with a boy at day- or boarding-school, where the boy receives a greater degree of care and oversight than can be given to the young man entering college; of all periods in life, the youth in his freshman year-fresh from the overshadowing care of home and school-may need judicious advice and timely aid. The change from the restraint of home and school to the freedom of college life is sudden and marked, and it is in this the first year of the boy or young man of 17, 18, or 19 years of age, that some tactful, judicious aid should be near him in his work and course. Some boys go to college so well prepared that they become careless and finally fall behind in their work from over-confidence. Others meet trouble from ambitiously trying to do more than their previous preparation, or physical or mental strength, can sustain. Others fall behind from illness-from injuries-from natural inability to grasp at first, without more aid than comes to them in the regular course of instruction, the higher mathematics-or mayhap the modern languages, or other subjects presented by the advanced curriculum of the present day. When a boy or youth begins to

Jan 1, 1911

By D. J. Parker

Since the introduction of electricity into the mines of the United States , the hazards incident to the industry have increased materially in both coal and metal mines . For economic reasons the tendency at present , particularly in coal mining , is decidedly toward the adoption of electrical mine machinery , including alternating current machinery , on a more extensive scale than ever before . Obviously, the growing use of such equipment will result in an ever -increasing number of underground transformer stations . The principal electrical hazards in mines are threefold ; fire , explosion, and contact . Of these , fire is the greatest hazard involved in the use of electricity underground , and several fires have originated in underground transformer and motor generator set stations . The fire hazard due to improperly installed and poorly maintained underground transformer stations is an ever-present one , and failure to take the necessariman remedial action is likely to result , sooner or later, in the destruction of life and property . Upon suggesting the necessary corrective measures with respect to such installations , one is often confronted with the statement to the effect that even though this particular hazard has existed over a period of years , there have been no unfavorable results therefrom thus far . Frequently , the desirability for action is not apparent to the mine management until it is too late . Because a mine has a record free from fires , explosions , etc. , over a number of years of operation during which these hazards existed , such good fortune should not be taken as a guarantee that this or any other mine is immune from these common dangers . When the elements of an existing hazard are properly balanced or in the right proportion, the unfortunate combination must of necessity culminate in misfortune of one kind or another. The fire hazard due to underground transformer installations can be very definitely minimized by proper installation and maintenance . In coal mines the transformer banks , connected to 2,300 and occasionally to 4,400 volt circuits , are often found located in open- ended crosscuts , mounted on concrete or timber foundations , and in nonfireproof surroundings .

Jul 1, 1930

MR. Woo&apos;s succinct description of the mining and smelting of silver-lead in Mongolia, with the roasting-and-reduction process and cupellation, has much interest as a picture of methods that not only may have been in use, as he suggests, a thousand years ago, long before the existence of mining schools or chemical laboratories, but probably vary little, if at all, from the practice of prehistoric times, when King Priam&apos;s handsome silver vases, cups and bowls were formed. For it is highly improbable that such large objects were made from comparatively rare native silver, and the metal must have been smelted from ore, and most likely in great part from galena,, with cupellation of the lead. Dr. W. A. P. Martin, in his excellent book on the Lore of Cathay, points out that Chinese alchemy is over 2000 years old, antedating the European by at least six centuries; and he infers that the Chinese skill in metallurgy and many branches of practical chemistry owes its origin to " those early devotees of the experimental philosophy who passed their lives among the fumes of the alembic." Those alchemists, however, may have more likely derived some of their leading ideas from the mys terious, and at that time wholly unexplainable results observed in already very ancient metallurgical processes; in which, for example, certain stones were transmuted, as it were, into metals widely divergent in character from their ores, and even silver and gold were obtained from the most unlikely-looking mate rials. It is therefore, in any case, not improbable that the Chinese may have preceded western nations in the discovery of metallurgical methods. At all events, it is now evident that the Japanese acquired these arts from China, the former source of all their higher civilization. My own observation of old-fashioned silver-smelt ing at Hosokura, on the main island of Japan, and about 220

Jan 1, 1903