Search Documents

By M. Imani, A. Fahimifar, A. H. Javid

"Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study to evaluate the ultimate bearing capacity for two interfering strip footings resting on a rock mass in which the strength can be described by the generalised Hoek–Brown failure criterion. This criterion is applicable to intact rock or heavily jointed rock masses that can be considered homogeneous and isotropic.The material is assumed to exhibit perfect plasticity and obeys an associated flow rule. The effects of Hoek–Brown parameters including GSI, mi, and sci were studied and the corresponding results are presented. For different clear spacing (S) between the footings, values of the efficiency factor (?) were determined; where ? is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that of a single isolated footing having the same width. The maximum value of (?) occurs at spaced between S/B = 0.5 to 1.0. The results have been compared with those available in the literature.INTRODUCTIONEvaluating the ultimate bearing capacity of rock masses is essential for important projects like dams and bridges. Closely spaced footings may occur on rock masses in the form of pier foundation and grillage footing. Close spacing lead to permit higher loads than can be bore by similar isolated footings. The ultimate bearing capacity of two interfering strip footings resting on cohesionless soil have been studied theoretically (Kumar, & Gosh, 2007; Kumar, & Kouzer, 2008; Stuart, 1962). Results revealed when two strip footings approached closely enough, failure zones affect each other and ultimate bearing capacity significantly increased."

Jan 1, 2015

By Stanley Noss

One need be neither an historian nor technologist to recognize that activi¬ties related to the conversion of coal to other usable energy forms have been active for nearly fifty years. The degree of such activity and its evolution to significant commercial proportions has, however, fluctuated widely with world circumstance. For the past decade there has existed both a consistent technology evolution effort in classic R & D proportions, and a mainstream commercial acti¬vity but in rather modest proportions when viewed from the vantage point of world energy needs. But the chain of events wherein it became increasingly obvious that we were in energy trouble irrespective of world politics, spurred alternative energy source activities in the fossil fuels areas. The oil embargo of 1973-1974 made the obvious even more so and provided additional emphasis for the need of such alternatives. Yet the preponderance of these added expenditures and activities (with one notable exception which is the subject of this discussion) has been focused on the intended identification of the best or ultimate process by means of analytical and modest empirical means, whereas our circumstance dictates a bold, higher-risk effort to prove the viability of coal conversion as an industry on a real-time, real-size, real-economics basis. With such proof on hand, industry demands in all related areas will provide the stimulus, motivation and environment for all processes. There is both need and room for many who will compete for a meaningful segment of this new industry which can grow at a rate never seen before in our growth history. The single program in the world today oriented specifically toward the goal of proof of industry viability is the Energy Research and Development Administration's CBF (clean boiler fuels) Program for which COALCON is proud to be the prime contractor.

Jan 1, 1976

By A Tolley

Bauxite residue or ‘red mud’ is a by-product of the Bayer Process, the primary process of alumina refining. Due to its high alkalinity and variable composition, its storage and disposal poses high environmental risks to water sources, surrounding ecosystems and human health. The high alkalinity (pH 12–13) is a significant factor in its classification as hazardous waste; to mitigate this, Australian refineries have integrated neutralisation processes into bauxite refining. Both sea water and carbon dioxide neutralisation processes are applicable. Multiple studies have demonstrated pH reduction from 12–13 to 7–10, depending on the method. The key advantages of CO2 neutralisation are that it allows for carbon sequestration and is more effective when utilised as a pre-treatment for recovery of metals, while sea water neutralisation is more established and has been integrated into two Australian refineries. This paper proposes the application of the bacteria Exiguobacterium oxidotolerans for bioleaching of iron from hematite in bauxite residue. The genus Exiguobacterium is characterised by its high levels of adaptability, halotolerance and alkaliphilic nature. E. oxidotolerans is successful at eluting Fe2+ from hematite via reductive dissolution, which complexes with oxalic acid produced during metabolism. This aquatic bacterium presents a novel process pathway for iron elution due to direct interaction of E. oxidotolerans with hematite via the cell membrane and operates within the pH range of neutralised red mud. The proposed mechanism is extracellular electron transfer, a microbial metabolic process where electron transfer is facilitated between bacterial cells and extracellular material. Currently this is being investigated for promotion of seaweed growth in coastal environments as soluble iron aids and fortifies colonies. This has potential downstream applications for cleaner iron and steel production. While theoretical, this paper explores the neutralisation, bioleaching and application of the Fe(II)- and Fe(III)-oxalate complexes formed.

Sep 18, 2023

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

By John D. Lupton

This paper will discuss the benefits and advantages of using 3D survey data in stope analysis. Obtaining detailed 3D survey data of underground mine progress and production is a challenge. It is almost impossible to ?see? around corners, underneath overhangs, or deep into dark, dusty, humid underground voids. Thus, valuable ore can remain permanently encased in backfill. Without the benefit of 3D survey data, underground mines have the difficult task of meeting grade quotas without the benefit of knowing exactly what has been mined. Lack of this data usually results in unfavorable month end Reconciliation factors, where grades must be adjusted to match grades assessed by the Mill.

Apr 1, 2005

By M. J. Shields

There are numerous suggestions in the literature on methods of obtaining representative samples of waste rock or mill tailings. Some suggested methods would result in thousands of samples and very high costs for a large facility. There is no general rule that can (or should) be followed, such as collection of a given number of samples per mass of material, per acre of impoundment, or per foot of drillcore. Each site is different, and the adequacy of sampling must be tailored to the site. A logical approach is to let the variability at the site dictate the number of samples that should be collected and analyzed, and then to quantify and evaluate the results by means of standard statistical methods.

Jan 1, 1998

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

By R. J. Watters

Many rock sass classification systems exist' to assist the engineer in assessing the rock support requirements for underground design. Our ongoing research in this area is directed at attempting to utilize the fractal dimension and the acoustic emission' response of the tuffs at Yucca Mountain, Nevada to further aid in rock mass classification. The Topopah Spring' member, the proposed nuclear waste horizon, is characterized by welded and partly welded tuffs, exhibiting a wide range in moduli, strength, porosity and degree of fracturing. Differentiating between the different' types of porosity can be extremely difficult if not impossible. An attempt was made to correlate the acoustic emission response with the porosity of the sample. Events and the peak amplitude may offer a means-to distinguish between, fracture porosity and pore porosity. In addition-, fractal dimension were calculated for several fractures in densely welded tuffs. Two techniques for calculating fractal dimension were-applied' to describe-fracture geometry and roughness. Fractures in-welded-tuff were-found to be relatively smooth.

Jan 1, 1989

By T. P. Meloy

Media mills operate by having energy transferred to the media which in turn grinds the feed material in a packed bed. Regardless of the mill type, the media energy density per unit surface area is constant. Since for optimum grinding conditions, both peak pressures and particle number of the bed depth are constant, the frequency of energy input is inversely proportional to feed size. As the particle size decreases the voles energy density increases linearly necessitating cooling in stirred mills. Grinding finer particles therefore, requires moving from rotary to vibratory mills, and the finest, the stirred mills.

Jan 1, 1987

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By D Kentwell

This extended abstract and associated presentation provide a series of real examples of the complex interactions between the numerous input parameters, both geological and mathematical, that are required for resource estimation. Many of these parameters can contain a large degree of uncertainty at the initial resource stage. The resource tonnages and grades at economic cut offs of some types of deposits are relatively robust to these initial uncertainties while others exhibit significant sensitivity. In some cases, changes in parameters can result in counter-intuitive outcomes. Grades and confidence levels are inseparable; as the parameters change the confidence changes and so does the grade estimate. The extended abstract and associated presentation also discuss the question of whether or not a single solution is still an acceptable outcome for an estimate or if even a set of simulations based on a single fixed set of parameters is acceptable.CITATION: Kentwell, D, 2018. Sensitive dependence on initial conditions in resource estimation, in Proceedings Complex Orebodies Conference 2018, pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By B. M. Davis

The Colosseum Mine is within the Clark Mountain mining district located approximately 72 km (42 miles) southwest of Las Vegas. Nevada in San Bernardino County, California. Gold mineralization at the Colosseum Mine is hosted in two 150 m by 210 m (500 ft X 700 ft) interconnected. rhyolitic intrusive breccia pipes that intruded Precambrian crystalline basement rocks and over-lying Paleozoic marine sedimentary rocks. Sub-sequent erosion (de-roofing) of all of the Paleozoic section and a portion of the Precambrian section has exposed the pipes to the present level (probably a significant depth in the original breccia pipe system).

Jan 1, 1989

By C. J. Lewis

Commercial lime plants in the United States and Canada are depicted in Figure 1. The sources of lime available to Nevada and bordering states are rather few. Chemstar Lime has plants at Apex, Nevada and Nelsen, Arizona. Continental Lime, Inc. has plants at Tacoma, Washington, Townsend, Montana and Delta, Utah. However, Continental Lime has a new rotary kiln installation underway near Wendover, Nevada. This plant is scheduled to come on stream in the fall of 1989.

Jan 1, 1989

By John Hartlen

"The 19th century was an ""age of gold"" and Nova Scotia experienced its share of early gold rushes. Gold mining activity in the province was focussed into three ""rushes"" which occurred, approximately, in the 1860s, 1890s and 1930s; a total recovery of 1.1 million oz. Au has been recorded. The purpose of this note is simply to chronicle the technical development of gold mining and processing in the province and to comment briefly on the recently renewed interest in this precious metal. The first public discovery of gold in Nova Scotia was made by a farmer in 1860 at Old Tangier or Mooseland, and this find sparked the province's first gold rush. The mining and milling methods of the 1860s were ingenious. Initially, arrastras, crude stone-hewn grinding mills, drawn by men, mules or horses, were widely used. Nova Scotia's first conventional stamp mill was installed at Mooseland by 1862; it was comprised of four wooden stamps and is believed to have been imported from Scotland. One of the largest waterwheels of the 1860s, reportedly 16 feet in diameter and 8 feet wide with a SO-horsepower rating, was used in the Renfrew Gold District to drive gold stamps. Steam power was also employed, and many of the engines were of native construction, as was the unit at Waverley's Lake Major Company, which had a piston 1 foot in diameter by 12 feet long and was connected to a 16-ftdiameter flywheel."

Jan 1, 1999

By J. Paul

Mining engineers in charge of open pit mine planning very often face decision making situations dealing with the selection of the most economical method for the removal of overburden. Ripping versus conventional drilling and blasting are the options considered. The choice of a particular overburden removal method depends upon the physic-mechanical properties of the overburden material as well as the various cost factors involved in the process. The analysis of techno-economical factors involved in different methods of overburden removal needs detailed study and investigation by a technical expert. But the expert system "Fragmentation System Design" has been created in a way such that it will help and expedite the decision making process relating to overburden removal in surface mines. Furthermore, this expert system can be used for detailed design aspects of overburden removal in open pit mines.

Jan 1, 1988

By R. J. Morrell

The Bureau of Mines, U.S. Department of the Interior, has developed a hardrock cutting concept and incorporated it into an extraction system called the ripper miner. This concept uses a single, wide bit that attacks the rock at a shallow angle and slow speed. Research has demonstrated that the system is capable of excavation rates exceeding those possible with conventional drill-blast and can effectively cut rock too hard for conventional roadheaders or continuous mining machines. It has the additional advantages of low bit wear and dust generation. This highly flexible concept is applicable to both mining and driving development openings and can cut any material from coal to hard rock. A single rip-per miner can perform the functions of a continuous mining machine, a roadheader excavator, and a tunnel boring machine. This paper presents the history of the development of the ripper miner from the initial laboratory tests through the construction and testing of the full-scale, lab prototype. It includes a comparison of the ripper miner to systems currently used from the standpoint of energy efficiencies and operating costs.

Jan 1, 1989

By Orson Cutler, Shepard

THE OBJECT of this paper is twofold: (1) To analyze the forces that cause air bubbles to spread on mineral surfaces in the flotation process; and (2) To develop a rational expression that will serve as a criterion of the floatability of minerals, to the end that the efficiencies of various flotation reagents can be accurately compared. Heretofore, the subject of the spreading of air bubbles has been dismissed with the statement that the surfaces of minerals on which bubbles spread are water-repellent. Imperfect understanding of the forces involved has led to the use, hitherto, of various erroneous formulas for the calculation of the comparative effectiveness of flotation reagents.

Jan 1, 1932