Search Documents

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By George A. Guess

The making of contracts for the purchase of ores is a business which the metallurgist usually understands better than the miner. Companies in the custom ore business often employ an ore buyer who is aware of the class of ore which the smelter needs, and is thoroughly conversant with the business. The miner on the other hand makes ore contracts but seldom, and it is often only after a settlement has been made that he realizes the meaning of the terms of the contract under which he has sold his ores. He has expectations usually greatly in excess of the amount 'net proceeds' shown at the bottom of the settlement sheet. Seldom does the occasional shipper really know his contract. A somewhat similar parallel is to be found in insurance policies. We all have insurance policies; we never know the conditions contained in them until after the fire. The clauses in the policy are for the protection of the Insurance Company. An Insurance Company has no friends.

Jan 1, 1926

By Dieter Neuschiitz, Pengfu Tan

"In order to understand the sintering phenomena during iron ore sintering process, a CFD model of iron ore sintering has been developed, combining with the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. This CFD model can be used to simulate the concentrations of the gaseous and solid species, temperatures of the gas and solid, melting and molten fractions of the mixture, gas velocities, temperature zones and residence times of the gas in each temperature zone. IntroductionThe off-gas analyses clearly revealed that the off-gas of a sinter strand does not have a composition corresponding to thermodynamic equilibrium, for example, the CO, CO2 and O2 concentrations are not the mutually consistent equilibrium values. Apparently the chemical reactions in the sinter bed are controlled kinetically. Therefore kinetic modeling of sintering reactions combined with CFD modeling is necessary to understand the sintering phenomena during iron ore sintering process.Several models of iron ore sintering have been developed since 1970 [l-l 4l, each being more refined than its predecessor. The models were formulated as a series of differential equations to describe chemical and physical changes occurring at a point in the bed. These equations were solved numerically in a vertical plane along the strand. The present CFD model, based on the Nath's model [14], has been published in the reference [15]. In this work, some new chemical kinetic models of gas-solid reactions are incorporated in the present CFD model. The concentrations of gaseous and solid species, temperatures of gas and solid, melting and molten fractions of solid, velocity of gas, and residence time of gas in each combustion zone can be calculated by this model."

Jan 1, 2004

By D. de la Villa

From 1989 to 1992 Rio Tinto Minera has developed and implemented a productivity program in its Huelva Plant, including Smelter, Acid Plant and Electrorefinery. This Plan was designed in order to increase productivity, reduce emissions and produce a better quality of cathodes. This paper describes investments and operating improvements involved in this project, focusing on Smelter and Acid Plants, and comments the results obtained so far.

Jan 1, 1993

By Don Ibana

The use of solvent extraction (SX) in process metallurgy is particularly attractive as it is applicable to a wide range of solute concentration and pH, and it allows complete separation of chemically similar metals such as nickel and cobalt and the rare earths among others. It is therefore applicable to the processing of low grade and complex ores, which is increasing and expanding owing to the diminishing reserves of quality ores, and this has driven the increasing and expanding use of SX.The current SX technology, however, has inherent limitations owing to the use of mechanical agitation as it induces high shear mixing. Excessive shear produces very fine droplets, and while this favours mass transfer, it also leads to sluggish phase separation. High shear mixing is also known to favour crud formation. All these factors as well as high power and reagents consumptions contribute to poor process efficiency. Electrostatic solvent extraction (ESX) is similar to conventional SX except that mechanical agitation is replaced with electrostatic agitation. In direct contrast to mechanical agitation, it allows the production of very small droplets that can be made to maintain intense motion, which favours mass transfer, without affecting the phase separation. In addition, as it uses an electrostatic field, the power consumption is minimal. Hence, it promises to be a superior alternative to conventional SX mixing although an application of the technique is yet to be achieved.Our work to develop an application of the technique in process metallurgy has now established that electrostatic field has no effect on either the stability of the reagents or the chemistry of the process. A volumetric flowrate that is comparable to that of a conventional sieve plate pulse column is achievable. We have also established that electrostatic fields can be made to yield much narrower droplet size distributions than those of mechanically agitated contactors, and they allow better control of droplet motions, which include oscillation and linear motion and hence, mass transfer. These are significant advancements toward our goal and shall be discussed in this presentation.

By James J. Scott

Friction Rock Stabilizers, trade name II Sp 1 it Sets'" have been under research and development by the author and the Ingersoll-Rand Company since February of 1973. The United States Bureau of Mines and the Mines Enforcement and Safety Administration as well as many mining companies have cooperated in field testing the device. Split Set rock anchors are distinctively different from the widely used mechanical rock anchors or fully grouted rock anchors. They control ground movement internally in a manner that allows controlled deformation during the early phase of the ground reaction curve but then, as secondary creep develops, anchorage per unit length increases and they serve to strengthen and stabilize the opening for long periods of time. The history of research and development of the Scott Split Set rock anchor system with accompanying laboratory and field test data is presented in this paper.

Jan 1, 1977

By Charles E. Robertson

As it becomes more and more apparent that our nation must place a great deal of reliance on coal as an energy source in the coming decades, prospecting for new reserves Un Missouri and other states in the Western Interior Region is increasing. As more and more of the known reserve becomes committed to existing or planned projects operators will be forced to look beyond the fringes of existing coal fields for additional reserves. Perplexing geologic problems invariably confront all prospectors and are particularly bothersome to those new to a particular area. It is the purpose of this paper to alert prospective operators to geologic problems likely to be encountered and to offer guidance in the recognition and solution of these problems. Particular emphasis is placed upon geologic structure and washouts. Other geologic problems have been discussed in a previous paper.

Jan 1, 1977

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

By R. P. Charbonnier

"To understand the operation of jigs and other separating processes based on differences in gravity, it is desirable to analyse the motion of various particles in given media under specific conditions. A summary of the earlier theories shows that they lead to unsatisfactory or excessively complicated formulae in cases such as coal jigging. By adopting a simplified theory of the motion of particles in a fluid, the size and duration of the initial accelerated motion of a particle falling in hindered settling can be calculated. Based on this mathematical analysis, examples referring to actual coal jigging practice show that it is desirable to prolong and/or repeat, as frequently as possible, the optimum conditions corresponding to an effective acceleration of the particles. The separation is then obtained according to gravity rather than to particle dimensions, as would be the case if the velocity of the particles• were allowed to approach its terminal value. To achieve this gravity separation, it is suggested that the suction phase of the jigging cycle be artificially prolonged and the frequency of pulsations increased as much as possible for washing the coals of smaller sizes."

Jan 1, 1959

By H. V. R. von Rhaden

Systematic quantitative X-ray diffraction analyses performed on diamond-drill cores originating from the Aandenk formation at the Loraine Gold Mine, located in the Welkom goldfield, Orange Free State, South Africa, have revealed the presence of a number of phyllosilicate mineral assemblages which have not hitherto been reported from this region. Rectorite, a regularly interstratified 1:1 mica-montmorillonite "swelling clay", is found to occur together with paragonite, muscovite, pyrophyllite, kaolinite, and chlorite in highly-altered friable rocks. The presence of rectorite in mill feeds may have potentially serious implications with respect to gold recovery. Quantitative X-ray diffraction analysis for phyllosilicates can be used as an aid to correlation, and also to guide the widths of stopes in underground mining. Rectorite has a unique mode of origin, which is discussed.

Jan 1, 1991

By Jack Thibodeau

During the past six years, most states have promulgated water quality regulations which contain numerical aquatic life standards for heavy metals. In addition, the Environmental Protection Agency (EPA) promulgated national water quality standards in 1992 which also include numerical aquatic life criteria for heavy metals. Numerous wastewater discharge permits have been issued by the states and EPA to industrial facilities which include low microgram per liter heavy metal limitations. In many instances, the limitations are below detection limits or treatability limits using state-of-the-art analytical methods or treatment technologies. This paper will discuss options for conducting studies, including the use of water-effect ratios, metal partitioning coefficients, and recalculation procedures to develop site-specific metals criteria and higher permit limitations. The installation of expensive metal treatment systems to remove trace metals may be avoided if higher permit limits are indicated by the site-specific studies.

Jan 1, 1996

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993

By J. Someehneshin

Nowadays along with population growth, industry development, consumption of mineral resources and the fact that the reserves on hand are running out, the depth of surface and underground mines for further exploitation are increasing. During recent years, in underground mining, the block caving method for low-grade and large-scale deposits has shown a growing rate of application. This method is very cost effective and economically affordable. The dimensions of blocks are one of the most important parameters which should be taken into account since it has been proved to have a great deal of effect on technical issues such as commencement of caving and mine design. Proper calculation of the length and width for a block in this method leads to proper caving and discharging which are the most important stages. Therefore, in this method, the calculation of the optimized dimensions (length and width) of blocks is not only important but also directly helps the productivity of extraction. In this study, firstly for the purpose of facilitation, some assumptions were considered and having used these assumptions for estimation of optimized length and width of block, a relationship based on rock mechanics and physics was explored. Furthermore, some necessary details were added to the said relationship and finally, it was transformed into an inequality. Solving this inequality provides us with the optimized length and width of the block. The explored relationship was analyzed with MATLAB software and the graphs thereof were drawn. In these graphs, each time one of the input parameters has been drawn up in a logical range so that it could be compared with previous states.

Aug 1, 2013

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000