Search Documents

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005

By S. S. Burns

"AbstractShovels of 18 cubic yard capacity and larger are described which incorporate advanced technology and techniques providing performance and operation tailored to meet the needs of open-pit mining.To achieve the goal s of increased production at lower cost with consideration of maximum availability, lower energy consumption per ton and low •impact on pit power, Harnischfeger Corporation developed a solid -state drive system (""Electrotorque"" - P&H trademark) and applied unique transmission methods.To date, more than 250,000 hours of experience in different parts of the world under varying operating and environmental conditions has proven that the ""Electrotorque"" shovel is the shovel of the future, today.This paper will discuss the electrical features and touch briefly on some mechanical features.Introduction to ""Electrotorque""THE hoist, crowd, propel and swing machinery of an electric mining shovel are driven by direct-current motors.A D.C. motor is used instead of an A.C. motor because the torque output per ampere input is at a maximum and the fact that it is doubly-fed (armature and field ) provides optimum flexibility in control.The power that is available in the pit is alternating current power. It is therefore necessary to change or convert this A.C. power to D.C. power so that the D.C. motors can be used."

Jan 1, 1977

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Vincent Castranova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

"A group of bisbenzylisoouinoline alkaloids has been shown to exhibit various degrees of effectiveness in preventing silica-induced fibrosis in animal models [1, 2]. The objective the present study was to characterize the binding of several of these alkaloids to phosphatidylcholine vesicles and rat alveolar macrophages using fluorometric and equilibrium dialysis methods, respectively. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, chiral configurations, and double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is a highly effective agent in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, certain analogues of tetrandrine such as curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In conclusion, the results of these studies indicate that alveolar macrophages exhibit large binding capacities for certain members of this class of bisbenzylisoquinoline alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds. These data also suggest that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.INTRODUCTIONInhalation of crystalline silica is associated with the development of silicosis. This fibrotic disease is characterized by the appearance of concentric hyalinized nodular lesions in the lungs with the progressive development of pulmonary dysfunction [3, 4]. Many theories concerning the etiology of silicosis involve silica-induced activation of alveolar macrophages. Evidence indicates that in vitro silica exposures result in the generation of chemiluminescence, and the release of superoxide and hydrogen peroxide from alveolar macrophages [5]. Activation of alveolar macrophages has also been demonstrated after intratracheal instillation or inhalation of silica [5, 6]. Such excess release of reactive products from pulmonary phagocytes has been associated with damage to the lung parenchyma [7, 8]. In addition, silica exposure results in the release of mediators from alveolar macrophages, which enhance proliferation of fibroblasts and collagen synthesis by these pneumocytes [9-12]."

Mar 1, 1992

By Xiqing Wu, Liang Dai, Tao Yue, Longsheng Yi, Ruifang Wang

Magnetic seeding flotation (MSF), i.e. adding magnetic seeds and pre-magnetization-flotation, is a new flotation technology especially for fine particles, which improves the flotation performance by enlarging the apparent size of the particles in a way of magnetic agglomeration. Both the fine coal slimes with a size of 66.68% –38µm and the pyrite slimes with a size of 73.95% –23 µm were investigated by the MSF, respectively. Flotation tests with variable of dosages of magnetic seeds and polyacrylamide were conducted, and some measurements, such as laser diffraction size analysis, magnetic susceptibility by vibrating sample magnetometer (VSM) and infrared spectroscopy (IRS), were also applied in order to probe the mechanism of the MSF. Based on the tests, measurements and calculations it was found that both the recovery of coal and the flotation kinetics of pyrite slimes increased with the additions of the magnetic seeds, and in the presence of polyacrylamide the coal flotation was further strengthened due to a synergetic effect of magnetic seeds and polyacrylamide on the flotation and a relatively larger apparent size of slimes after additions of magnetic seeds and polyacrylamide. The reason for the MSF lies in fact that the presence of the polyacrylamide intensified the adsorption of magnetic seeds on the coal particles and increased the coverage of the magnetic seeds on the coal surface from 0.2 to 1.3 wt%, resulting in increased magnetic susceptibility of coal particles from 9.13×10-9 to 22.17×10-9 m3/kg and thus a low magnetic field strength of pre-magnetization needed for the magnetic agglomeration among the coal particles from 602 to 24 mT prior to proper flotation. IRS shows that polyacrylamide chemisorbed on the surfaces of both coal particles and magnetic seeds, thus acting as the bridging media between particles and seeds.

Jan 1, 2016

By J Player, R de Vries, J F. Carswell, R Hassell

"The feasibility of Dugald River mine was highly sensitive to mining and geotechnical design assumptions, particularly stope dilution and strike length. Following the start of initial mine development in 2012 the project was suspended in 2013 due to concerns over the complex ground conditions and resulting dilution, stope sizes and general mineability. A technical risk mitigation program was undertaken with a key aim to increase the level of confidence in predicting stope dilution.A stope sizing and dilution model was developed that provided a range of stope sizes based on geotechnical conditions and acceptable dilution. The original feasibility used a standard stope size of 25 m height by 25 m span. The new model was used as the foundation for the subsequent updated development plan for Dugald River that reduced much of the previous technical risk through greater confidence in the geotechnical and mining parameters.Several methods to predict stope hanging wall dilution and appropriate stope size have been used at Dugald River that relied on the modified stability graph method. Improvements to the method were identified as more rock mass and mining data became available through the completion of a trial stoping program, increased underground development and a large geotechnical core logging campaign. These improvements not only focused on the technical aspects of the model, but also on creating an easy to use and sustainable process that could be used at multiple stages of mine planning from life-of-mine (LOM) through to final stope design.Several of the main improvements are: understanding stope failure mechanisms and collecting only geological information that is most relevant detailed modelling restricted to the rock mass that could be expected to influence stope behaviour accounting for different stope failure mechanisms with the stability chart method assigning a geotechnical confidence factor to the data making it useful as a mine planning tool with integration into the mine planning process using performance of completed stopes to update and calibrate the model.The model provides recommended hydraulic radius and associated dilution estimates across the ore body. Providing the hydraulic radius allows planning engineers the option to consider single, double and triple lift stoping options suitable to mine scheduling. While the model has been calibrated for conditions at Dugald River the process used to create the model is not site specific and is applicable to other steeply dipping tabular orebodies.CITATION:Hassell, R, de Vries, R, Player, J and Carswell, J F, 2017. Improving the prediction of stope hanging wall dilution – a critical factor to the success of Dugald River, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By David J. Kusler

This report describes a rapid, reliable, and relatively simple method developed by the Bureau of Mines Pyrometallurgy Laboratory at Bruceton, Pa., for determining lime (calcium oxide) and magnesia (magnesium oxide) in various materials containing these constituents in greater than trace amounts. Optionally, titania (titanium dioxide) may be determined for the same sample. The accuracy of the method, suitable for most purposes, is shown by comparing the Bureau results with those obtained by accepted procedures. The method has been applied satisfactorily to the routine analysis of blast-furnace slags, for which purpose it was primarily developed, and to other calcareous compositions. In the Pyrometallurgy Laboratory it has replaced the standard methods previously used to determine lime and magnesia, and has been in general use by that laboratory for the past several years. The analysis time, generally under 3 hours, is considerably less than required by standard methods.

Jan 1, 1960

By J. Kevin Cotchen

The results of "submerged arc" electric furnace processing of a variety of materials is discussed with respect to the process and products, including the characteristics of the products (e.g. TCLP or Toxicity Characteristics Leaching Procedure). The materials melted include slags and wastes containing various metal oxides including copper, tin, lead, zinc, chrome, nickel and other associated elements. The findings of these tests are compared to those reported in the literature for other operations treating similar "wastes".

Jan 1, 1992

By S S. Kanchibotla, E J. Sellers, L Julian, A Musunuri

Fume events in coalmines are typically associated with wet conditions, soft ground and deep holes. An ACARP research project used laboratory and field testing combined with literature reviews, numerical models and field investigations to characterise the influence of these conditions on the propensity for fume. This paper highlights the results for soft ground and wet conditions and proposes a proactive fume mitigation methodology. A simple numerical model is used to show how fume arises in soft rock that yields more under the loading of high-pressure, water-resistant explosive blends than for ANFO. The blends cool more rapidly after detonation into the lower temperature zone favourable for NO2 production. Low-pressure, high detonation temperature explosives are loaded or charged into soft ground. Water resistance must be considered because soft, faulted and fractured ground can lead to fume from degradation by water flow and non-ideal detonation of product in cracks.A suite of tests were developed to quantify ANFO and emulsion blend performance over time that can be carried out in a mobile laboratory on-site. Index tests such as viscosity measurement and water resistance in beakers are proposed to quantify long-term product performance because small components, such as surfactant, prill impurities and prill fines, contribute to inconsistent product performance. Water ingress experiments and detonation tests aligned with field investigations identified and characterised the role of groundwater in damaging ANFO and causing fume.Fume risk management is achieved using a proposed proactive fume mitigation methodology to characterise influences such as seasonal rain variation, groundwater flow hydrogeology, rock mass strength and structure well ahead of blast design. The design of blasts and selection of explosive products to consider expected conditions will reduce fume, improve efficiency in the mine and offer cost advantages.CITATION:Julian, L, Musunuri, A, Sellers, E J and Kanchibotla, S S, 2015. Mitigation of post-blast fume in soft ground and wet conditions, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By Nicholas E. Vanderborgh

Projections show that domestic coal will serve for the majority of energy supplies during the next decades. Thorough chemical cleaning of this coal can be accomplished in long-residence time, slurry-transport systems to produce high-quality fuel product. Concurrently, mineral recovery from coals will supplement existing ores. This paper describes this concept and gives preliminary engineering considerations for mineral recovery during transport operations.

Jan 1, 1982

By Nabil A. Bibawy

The U.S. Bureau of Mines has established a method for the calibration of class 2 and class 4 standards of mass using a procedure from designs developed by the National Institute of Standards and Technology (NIST). This method produces a weight calibration that is within 1.0 pct of the balance sensitivity. A set of four 1-kg weights yielded a standard deviation of 3.25 mg compared to ±2.91 mg balance sensitivity. The method employs the use of a high-accuracy balance to measure the difference between a set of weights calibrated by NIST and the set to be calibrated. The error of the balance is included in the error for each weight calibrated.

Jan 1, 1989

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of 873°K is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composition formed under roasting of concentrates with particle sizes less than 0.02 um (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CuFeSz2 each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forchamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013