Search Documents

By Harold Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand-book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By Duk-Won Park

The PSU/MVS program, one of the computer programs for ventilation network analysis most recently developed at The Pennsylvania State University, was applied to the analysis of modifications to an existing ventilation system for a coal mine located in southern West Virginia. The program is well designed and has diversified capabilities which allow the users to make decisions on the optimum size and number of fans, the location and number of airshafts, and the optimum operational procedures. The mine had 10 working faces, from which the average production rate was about 5900 tons of clean coal per day. Two vane-axial mine fans were used in parallel at a shaft, and both of them operated simultaneously. One additional shaft was in the final construction stage and it would be used in four months to alleviate the load for the existing fans and distribute intake air more evenly. The overall ventilation surveys, including the altimeter pressure survey and the air quantity survey, were carried out in the mine entries, shafts, slopes, and gob areas. Computations were made using the above-mentioned computer program on the present condition and after one additional fan was placed in operation at the new shaft. Also, recommendations were made on the air route and fan blade settings for the most economical and efficient ventilation system. Further studies were carried out to decide the proper period when the third air shaft would be required according to the long-term mining plan. Additional branches were added for the next 4 years of the production plan, and the ventilation conditions were tested at the end of each year. Numerous combinations of blade settings and modifications of air routes were tested. It was recommended that the third air shaft be added at the end of the third year so as not to experience fan stall.

Jan 1, 1982

By Juhani Pulkkinen, Pekka Lappalainen

Preplaced cable bolts - fully grouted old hoisting cables or stress relieved steel strands - have been used succesfully to pre- reinforce ore contact zones and pillars in sublevel stoping at Outo- kumpu Oy mines for ten years. The purpose is to make open stoping methods possible even in "poor'' conditions and to decrease waste rock dilution. Since 1971 more than 120 km cable bolting has been done, and plans for this year in five mines amount to 33 km. In order to understand the function of cable bolt, pull-out tests have been done both in the laboratory and in situ. Bond strength between cable and cement is highly dependent on cable structure and cable surface dirtiness. Steel cables with steel core and rough surface structure have highest bond strength ( 6 MP~). A cable bolt is a friction bolt. After losing its peak bond strength - after starting to move - a cable bolt still has a high loading capacity due to the friction caused by the uneven surface of the cable. Cable bolting is done before actual stoping from existing drifts, sublevel drifts, e.g. or from special bolting drifts. In general stress relieved steel strands are used; 2 x 15.2 mm dia per hole. FEM or BEM calculation is utilized in cable bolting design. Bolts 2 are in fan shape, 10 m ... 50 m long and are spaced 1/20 m ... 1/50 m2 at stope walls. Pretensioning of cable is not needed, when bolting is done before rock deformations. Bolting costs vary between 0.3 USD ... 1.0 USD/ore ton. In the beginning only manual cable installing technique bras used. Now bolting can be done as fully mechanized with the developed cable bolting machine; i.e. drilling of the hole, installing and cutting of cables and grouting of hole.

Jan 1, 1983

By D. W. Collins

Several organic and inorganic substances are widely used to control deposit structure and morphology during the electroprocessing of copper. Methods for monitoring the levels of thiourea, glue and guar gum during electrorefining and electrowinning have been successfully developed under the trade names of Reatrol and CollaMat. Other instrumental methods have been developed for additives and decomposition products associated with the electroplating of copper and other metals. Generally, these methods have been found to be either insufficiently sensitive or lacking in the desired selectivity for some or all of the additives. These procedures have mostly employed DC techniques; i.e., cyclic voltammetry, Tafel analysis, etc. In this work, chronopotentiometry (CP) and AC voltammetry were used to examine the interaction of glue, guar gum, thiourea and chloride during the electroplating of copper onto a platinum electrode. In addition, the interactions between the additives have been explored. It was found that glue in pure electrolyte (H2S04 and CuS04 only) had no effect on the chronopotentiogram. Glue was only active if chloride ions were present. The addition of thiourea resulted in several different chronopotentiograms depending on the presence of either chloride or chloride and glue. Thiourea used in conjunction with glue and chloride showed a significant increase in the polarization during copper deposition when compared to the electrolyte containing only glue and chloride. The use of a modified channel electrode further increased the sensitivity of CP. The use of AC voltammetry was explored as a technique to monitor some of the additives. AC voltammograms have more spectral detail then their DC counterparts and it is possible to monitor some of the additives at very low concentrations with AC techniques.

Jan 1, 1999

By K Zic, P Pickering, P Fraser

Water is a defining feature of the Pilbara. Its management was and remains vital for the pastoral industry which European settlers established when they first came to the Pilbara, and for the mining industry which now dominates economic activity in the Pilbara. Water availability in the Pilbara is, however, problematic. Severe droughts and major floods can occur at close intervals. In response to this uncertainty, the Department of Water undertook a Prefeasibility Study to determine, at a high level, the water requirements and opportunities in the Pilbara region. This paper reports on the outcomes of this study and the water integration opportunities in the region, identifying the sources of water supply and offers possible options for managing this water sustainably for the present and future demand. A range of supply opportunities is reviewed including: dewatering from mining operations, surface water, and desalination. All opportunities were subject to order of magnitude costing, including capital, whole of life and retail unit pricing with preferred options receiving further interrogation through triple bottom line (TBL) analysis to prioritise solutions. Options were also subject to intangible quantification (IQ) including benefits from the reduction of carbon emissions to ensure that the preferred option is based on factors other than just the least cost. Demand analysis was undertaken to identify current and future requirements and were assessed through review and integration of regional and sub regional master plans and consultation with mining, agriculture, industry and the community. The paper concludes that the viability of a Pilbara integrated water supply scheme depends on the development of a financial mechanism involving both government and industry participation models. The agreed scheme formed the basis of a submission to Infrastructure Australia for funding assistance.

Jan 1, 2009

By Charles Barrett

THE orientation of metal crystals and grains, both large and small,. can be determined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satis-factory in the laboratory the reflection of light from crystallographic etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographic projection is used to facilitate handling the data, this note may be considered as an appendix to an earlier review of the metallurgical uses of the stereographic projection.1 Various methods involving etch pits have been used by other investi-gators, Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4), holding it at arm's length, and marking a spot on it when it has been turned so that the etch pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2° and is extremely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czoehralski, 5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers"' developed a method for estimating the number of grains in a polycrystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and recrystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereo-

Jan 1, 1940

By Walter Snelling

IN the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I 'experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment.

Jan 4, 1915

By Keith T. Griffiths

INTRODUCTION The Empress Nickel Mine is situated forty-eight kilometres west of Kadoma in the Zhombe Communal Land of Zimbabwe. The mine came into operation in late 1968 based on a proved and probable ore reserve of twenty million tonnes. The initial production rate was 55 000 tonnes per month from underground. This was boosted to 85 000 tonnes per month in mid 1970 when the opencast operation came into production. The mining method at Empress is sub-level open stoping with main haulages mined at ninety metre intervals and sub-levels at eighteen metres. The extremely wide ore body of up to one hundred metres in width has necessitated leaving extremely large rib pillars and sill pillars in position to maintain mine stability and to act as regional support of the hanging wall. In early 1976 the opencast operation had reached its final economic depth and it was then necessary to increase underground production to 85 000 tonnes per month. Since a large portion of the ore reserve remained in both rib and sill pillars, it was necessary to embark on a positive pillar recovery programme. For this reason it was decided to introduce a sandfilling programme for the mined-out stopes and a modified system of sub-level open stoping with post filling of the lower stopes. ORE BODY GEOLOGY AND GEOMETRY The Empress orebody outcrop has a strike length of nine hundred and fifty metres on a north west - south east axis. It is a steeply dipping (65' - 75') tabular orebody of gabbroic rock which has been extensively altered. The north west - south east strike length of nine hundred and fifty metres on surface reduces to some two hundred

Jan 1, 1983

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By Z. F. Oszter, D. Vincent, W. K. Behrands

With the expansion of open pit operations, belt conveyors are going to be used in the 13 608 to 18 144 t/h (15,000 to 20,000 stph) capacity range, which calls for a review of some of the horsepower calculation methods. This paper presents methods (based on German research data, field tests and theoretical considerations) for the evaluation of the Ky factor in the CEMA formula for belt conveyors of large carrying capacity, which fall beyond the limits of the data given in tables in the CEMA book. (The CEMA limits are 407 N\\m (300 lb ft) and Tave = 7.3 Mg (16,000 lb). At these large loads, the impression resistance of the belting on the idlers plays a major role, which in turn influences the magnitude of the drive horse power required. An example will illustrate the order of magnitude difference of the horsepower values obtained by using a conventional calculation method and the suggested method, as well as the beneficcia1 influence of the 4-roll idler in comparison to the standard 3-roll unit for a large caving capacity belt conveyor. This paper concerns itself with the analysis of the resistance to motion of belt conveyors, emphasizing the evaluation of the frictional resistance to motion due to load and belt pressure on the idlers and the flexing resistance of the belt and material when passing over the idlers. In the case of long and heavily loaded belt conveyors, the aforementioned resistances reach extremely high values calling for close analysis of the phenomena, presently not calculable with normally used formulas. This paper establishes correlation between experimental and empirical data presenting practical formulas a tool for the designer of high-capacity belt conveyors. The application of the formula is illustrated in an example in the Appendix.

Jan 1, 1981

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Robert J. Ramsey, N. Finkelstein, Foster J. Witthauer

First mining operations in the Tyrone District, located just north of the Burro Mountains in Grant County, New Mexico, commenced in the 1870's. A major operation was undertaken by Phelps Dodge Corporation in the early 1900's when a 2,000 ton per day underground mine was developed and a gravity concentrator was built east of the mine and across the Continental Divide. It was during this time that the picturesque Tyrone townsite was built and occupied. In 1921, however, the underground operation was closed because of high operating costs and low demand for copper. The area was drilled extensively during the 1950's and in October 1966 Phelps Dodge announced the pending development of the new Tyrone with a large open-pit mine, a modern concentrator, suitable support facilities, and a new townsite to be located between the mine and Silver City. Stripping for the pit and construction of shop and milling facilities began in 1967. By the spring of 1969, ore was being stockpiled near the primary crusher. Operation of the concentrator on a 3-shift per day basis commenced on July 17, 1969. The concentrator as initially built had one primary, two secondary, and five tertiary cone crushers, two grinding sections of six ball mills each, two flotation sections, four filters, and four tailing thickeners. 'he capacity was about 30,000 tons per day. In 1971 and 1972, the capacity was increased to 48,000 tons per day by the addition of one secondary and two tertiary crushers, one section of eight ball mills, one flotation section, two filters, and four more tailing thickeners. Centralized automatic control was built into the original and expanded facilities to the greatest extent possible, considering the state of the art at that time. Installation of additional control

Jan 1, 1976

Endurance Properties of Non-ferrous Metals Discussion of the paper of D. J. McADAM, JR., presented at the Syracuse Meeting of the Institute of Metals Division and issued, as Paper No. 1506-E, with Mining AND METALLURGY, October, 1925. H. F. MOORE,* Urbana, Ill. (written discussion).-This paper says that the results of tests of some non-ferrous metals made at the University of Illinois and in the testing laboratories at McCook Field are abnormal when they do not agree with results obtained by the author. The writer can see no inherent reason why results of the type uniformly reported in this paper are any more normal. The knee of the stress-cycle, or S-N, diagram comes at different lengths of life for different metals. For steel, the knee occurs after from 1,000,000 to about 4,000,000 cycles, and for some non-ferrous metals not before 20,000,000 of 30,000,000 cycles. The writer can see nothing inherently abnormal in finding certain nonferrous metals for which the knee of the stress-cycle curve occurs at 1,000,000,000 cycles or higher. The writer has had experience with both the cantilever and the rotating-beam testing machine, and thinks that the chance of whipping action in the cantilever machine is a more serious handicap than the action the author has pictured. Furthermore, the writer questions whether the author has shown the existence of a clearly marked and definite endurance limit for all the non-ferrous metals he has tested including the following: Nickel (CT and A-16, Fig. 1), monel (CS-5.5 and BK, Fig. 2), bronze (F and CK, Fig. 4), aluminum bronze ( BJb-1, Fig. 6).

Jan 12, 1925

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By Rachel De Lucas

In recent years, as the price of oil soars upward, scientists have started to focus on other energy sources, such as hydrogen. As magnesium can be used for hydrogen storage by forming MgH2, industry will see a growing demand for the hydride. In hydrogen storage and release cycles using magnesium, hydrogen is released from magnesium hydride through hydrolysis and magnesium hydroxide is produced. Therefore, recycling magnesium hydroxide back to magnesium becomes important. The solid oxide membrane (SOM) process is an emerging technology for this process. In the SOM process, MgF2-CaF2-MgO flux is contained in a stainless steel crucible, which works as the cathode. An ionic-conducting YSZ membrane, connected to a liquid metal anode, is partially immersed in the flux. During electrolysis, when the voltage between anode and cathode is higher than the dissociation potential of magnesium oxide, magnesium ions move toward the cathode and are reduced into magnesium vapor. The oxygen ions move toward the anode, passing through the YSZ membrane. They are then oxidized, forming pure oxygen, CO/CO2 or steam (by reaction with hydrogen). The magnesium vapor, generated at the cathode, is collected in the condenser as high purity magnesium. SOM experiments have been conducted with different liquid metal anodes and without reductants. The SOM technique is a highly energy efficient process and with by-products being oxygen or steam, it is also an environmentally friendly green process. A 2-D electrostatics mathematical model was developed as an initial step towards optimizing the design for a three-tube scale-up SOM electrolysis cell. Several possible geometries were examined to develop the scale-up model and convergence of the model was achieved.

Jan 1, 2006

By Fred Leighton, Wilson Blake

The microseismic method of detecting instability and high-stress zones in underground mines was developed by the U.S. Bureau of Mines (USBM) in the early 1940's.l,2 For about 25 years this method has been used throughout the world by mining and construction companies in assessing the stability of underground and surface excavations. Rock noises are the release of small amounts of stored strain energy propagating outward from their source as a seismic wave that can be detected with special geophysical equipment. This release of strain energy is caused by a rock mass undergoing load changes resulting in small-scale displacement adjustments such as microcracking, shearing, sliding, and crushing of crystal grains, some even as small as the elastic displacements themselves. No detailed field studies of any of these mechanisms have been made, and knowledge about the origin of rock noises is relatively incomplete. Laboratory tests have shown that when rocks are stressed in a testing machine, the rock noise rate-the number of rock noises generated per unit of time increases with increasing applied stress.3 This increase is most pronounced as the ultimate strength of the rock is approached. The standard field procedure has been to monitor a rock structure at intervals and plot rock noise rates vs. time, thus gaining a semiquantitative estimate of the behavior and stability of the structure. The success of such monitoring, however, has depended almost entirely on the experience and knowledge of the operator, his interpretation of the data, and his equipment. Very little study has been devoted to the basic properties of the vibration record of a rock noise. USBM decided that the microseismic method was being used sufficiently by various mining and construction companies

Jan 1, 1970

By Albert F. J. Bordeaux

The immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia., would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or are even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a map of Eastern Siberia, showing the mineral deposits.

Jan 1, 1913

By J. Siege1, R. S. Popielak

A computer model was used to simulate the effect of leakage through confining beds on a hypothetical in situ leach operation in an aquifer with a thin mineralized section. The simulations were used to assess economic and potential environmental implications of leakage on an in situ leach operation. Four scenarios were modeled - three representing cases with different degrees of confinement, and the fourth representing a stratified ore zone under a low degree of confinement. The model simulated the travel path and travel time of lixiviant given the hydraulic conditions prescribed in each scenario. The results show that the travel path and travel times vary by about 10% for confinement ranging from nearly impermeable (essentially no leakage) to an extremely low level (thin confinement with a permeability about equal to that of the aquifer) for isotropic aquifer conditions. The aquifer thickness contacted by the lixiviant varied from 85% to 90%. Horizontally, 55% to 60% of the aquifer was contacted. The flow paths in the stratified aquifer were reduced in the vertical direction and expanded horizontally. Forty- five percent of the aquifer thickness was contacted vertically with 88% contacted horizontally. Break- through time for lixiviant traveling at mid-depth of the aquifer increased two times when the leakage was increased from nearly zero to a value representative of thin and highly permeable confinement. Leakage affects the economics of in situ mining by (1) increasing the time required to leach out the ore, and (2) increasing the thickness of the ore zone aquifer to be restored. The potential for environmental impacts appears to be minor. In all four simulations, the lixiviant did not contact the confining strata. Restoration would be limited to cleanup of the ore zone aquifer within the thickness contacted by lixiviant and within the radius of the lixiviant that traveled farthest away from the production cell.

Jan 1, 1988

By Charles H. Snow

In vol. xxxviii. (1889) of the American Journal of Science, under the heading " Pseudomorphs of Native Copper after Azurite from Grant County, New Mexico," Mr. W. S. Yeates describes a most interesting mineral form. His account is, that a material having the appearance of native copper, but brittle and much lighter than native copper (its specific gravity being but 4.15), was submitted to him by the United States National Museum for examination. The substance was reported to him as occurring in masses, varying in weight from one ounce to seventy pounds, and composed of tabular crystals, variously grouped. The specimens, when submitted, ex hibited on the outride a covering of clay; and they were subse quently found to consist of particles of the same clay, intimately mixed with others of native copper, producing the aspect, without the weight, of pure copper. The forms of the azurite crystals, found at Bisbee, Arizona, having been suggested by the specimens, actual goniometer-measurements were made; and the two crystallizations were thus proved to be identical. To these statements I may be permitted to add some further in formation, derived from personal examination, and illustrated with a suite of characteristic specimens collected by myself (Fig. 2).* Grant County, New Mexico, in which these specimens were found, is a region noted for variety of mineral species. The sixth edition of Dana's Mineralogy mentions many of the silver, copper, and lead minerals, and also turquois, aragonite, wulfenite, barite, fluorite, vanadinite, etc. I have noticed also green and red garnet, molybdenite, native alum, smithsonite, bornite, etc., some of which presented peculiar modes of occurrence. The green garnet, for instance, was in masses formed of separate crystals, each of pea-size and not unlike that vegetable in tint and smooth opaqueness. The crystallization was

Jan 1, 1893

By James Norman

SEPARATION of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers1 have noted that varying amounts of sphalerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solu-tions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939