Search Documents

By R. J. Wagner, G. H. Gronhovd, A. J. Wittmier

The paper describes the results of a series of full-scale boiler tests run to determine the ash fouling characteristics of a North Dakota lignite as a function of sodium content of the coal. Four levels of sodium were investigated and rate of fouling was determined both by boiler performance and by specially constructed probe equipment. Discussed is information on chemical and physical properties of the ash deposits. The vast lignite deposits in North Dakota are becoming increasingly important as a source of low-cost fuel for power generation. A new 200-megawatt lignite-burning plant located near Stanton, N.D., was placed in operation early in 1966. Another 172-mega-watt unit in the same area is scheduled for operation late in 1966, and plans have recently been announced for a 212-megawatt unit to be in operation by 1970. If these plants show good performance, western North Dakota could become a major power production center for a large geographic area in the upper midwest. One of the problems associated with the use of lignite in power boilers is its tendency to form troublesome ash deposits on boiler tube surfaces. This problem varies considerably from one lignite-fired boiler to another and is dependent upon such factors as source of lignite, boiler design, load factor, tube metal temperatures, and soot-blowing practices. This report presents data on sodium content* variation in a North Dakota mine, describes the results of a series of tests performed to determine the relationship between ash fouling tendencies and the sodium content, and tells how the mining company and electric utility have coordinated their operations to reduce the ash fouling problem. GENERAL BACKGROUND Until recent years it was generally assumed that North Dakota lignite from a given mine had qualities peculiar to that mine, but that within the mine, the lignite was quite uniform. In 1959, the Otter Tail Power Co. installed a 53.5-megawatt lignite-burning unit at its Hoot Lake plant, Fergus Falls, Minn. Shortly after the unit was put into operation, it was noted that at certain times under high load conditions, ash fouling problems were quite severe, but not consistent or predictable. Each time fouling occurred in the unit the position of the loading shovel at the mine was noted. Within two years it became apparent that there were certain areas in the Knife River Coal Mining Co. mine at Beulah, N.D., where the lignite apparently had a high fouling tendency for the Hoot Lake unit. Results from analyses of the coal did not show large differences in moisture percentage, ash percentage, heating value, or ash fusion temperature between the highly troublesome and less troublesome coals. After three years of operation, the troublesome areas had been quite well defined and the mining company started a procedure of bypassing these areas when load conditions at the plant were high and then returning to the troublesome areas to load the lignite during the summer months when peak loads were lower. It was noted that the lignite from the areas which caused severe fouling under high load conditions produced much less fouling at the lower summer loads. However, bypassing certain areas in the strip pit caused the mining company to disrupt their continuous loading schedule, which in turn upset their continuous stripping schedule and made for less efficient mining operation. Meanwhile, at the Hoot Lake plant, the number of soot blowers on No. 2 boiler had been increased from 30 to 55, and a very rigorous blowing schedule had been adopted resulting in soot blowers operating at least some part of 21 hrs per day. Fouling problems continued, with a resulting reduction in plant economy and reliability. During this period the Federal Bureau of Mines Coal Research Laboratory at Grand Forks, N.D., had initiated various research programs relating to the study of lignite ash and ash fouling problems. One project was a survey in which full seam samples were obtained from various locations in all the major

Jan 1, 1968

By John E. O’Rourke, Kevin M. O’Connor, Pamela H. Rey

INTRODUCTION The resurgence of coal mining activity in the United States, brought on by the spiraling costs of fossil fw1 energy in the Seventies, has come at a time of intense public concern for the quality of the environment. Notwithstanding pressure on our economy to develop alternate sources of fue1 energy to the import of oil, the legislatures of several states have reacted to public concern over the environment by passing strict regulations aimed at con- trolling the subsidence effect s of underground mining. Agencies of the federal government charged with assistance to the mining industry, including the Department of Energy and the Bureau of Mines, have sponsored a number of instrumentation and field measurement projects aimed at the development of subsidence prediction models that can aid the mine operator's task of subsidence control. There are good empirical models developed in Europe for subsidence prediction, but they were made possible by a large body of mining-induced subsidence data collected there over a long period of time. No com- parable subsidence data base exists in the United States, and consequently empirical modeling of subsidence is not a realistic approach for our near term needs. Moreover, the geologic and topographic diversity of the several coal regions in the United States is expected to necessitate the development of several empirical models, each one expected to be relevant to its own region. Because of the time and costs that are likely to be involved in an empirical modeling approach, it is considered more expedient and cost effective to develop a general, mechanistic model for subsidence prediction purposes. In order to develop such a model, it is necessary to investigate and quantify the mechanics of the subsidence process from the mine level up to the ground surface. The series of projects discussed in this paper are designed to achieve this objective and include the following work: (1) the identification of geotechnical instrumentation that will pro- vide mine level overburden and surface subsidence data. (2) a field demonstration of selected instruments, and (3) documentation of case histories for complete subsidence mechanics, using the demonstrated and preferred instruments. An identification of feasible instrumentation and monitoring techniques was completed by Woodward-Clyde Consultants (WCC) in 1977 (O'Rourke and others). This paper discusses a demonstration of those instruments at a mine in Utah, and at two subsequent projects, currently underway at longwall mines in Colorado and West Virginia. 'he latter two projects when complete will provide documented case histories of subsidence mechanics. The process of optimizing subsidence instrumentation and monitoring techniques to the conditions encountered during installation and monitoring for these underground mines is shown to be an evolving one, and one which has had some notable successes to date. INITIAL DEMONSTRATION The initial design and demonstration of selected monitoring systems was carried out at the SUFCO No. 1 mine, near Salina, Utah. The instrumented panel was approximately 152 m wide. 640 m long. and was 290 m to 320 m deep. The mined height of coal. seam averaged 2.4 m. The mining method was room and pillar using continuous mining machines. This method allowed some monitoring of the supported condition during development, and eventually allowed monitoring of a caved system when both chain pillars and room pillars were extracted on retreat. The two instrument systems shown on Table 1 were selected from the earlier feasibility report for demonstration at SUFCO No. 1. Collectively, the two systems, one for a fully-supported mining method and the other for a fully-caved method, incorporate most of the instrumentation to be found within all five systems listed in the earlier feasibility report. The instrumentation includes surface, subsurface and mine monitoring installations. All of the SUFCO instruments selected to meet the specifications of the general instrument types listed on Table 1 were manually operated. That is, data from the installed system could only be obtained while a person was there to physically observe or operate the system readout. Automatic data recording equipment was available for some installations, but the objectives were to keep the systems as simple as possible for the demonstration project. A complete description of the surface, sub- surface and mine level instruments, and the demonstration project results are given in WCC (1982), and selected features are discussed in this paper.

Jan 1, 1982

By R. D. MacDonald, John Dasher, A. M. Gaudin

ION exchange is a widely used unit operation in water treatment and elsewhere in chemical industries. It has occasionally been used in hydro-metallurgy for treating plating, pickling, and rayon wastes Concerning ion exchange in extractive hydrometallurgy—for treating ore leach solutions— the literature prior to the Geneva Conference has given only hints."-" Yet most of the ore leach plants now being built or completed in the last three years use ion exchange for this purpose. Most of these plants are used for extracting uranium. The overall process for leaching low grade uranium ores and the history of its development have been given in the authors' previous papers.',' The object of this paper is to discuss certain engineering aspects of the new application of ion exchange to recover dissolved values from ore leach solutions. Necessarily the illustrations will be taken from the first application—to uranium metallurgy. Although ion exchange processes have been devised in which separation of spent residue from pregnant liquor is not required, as in the RIP process,"-'I only ion exchange operation, in which the resin is contacted with a clear solution, will be discussed in this paper. Uranium exists in acid leach liquors mainly as the cation UO," and can be adsorbed completely by cation exchange resins, but the adsorption is not selective as other cations such as Fe++, Fe+++, Al+++, Mg++, Mn", and Ca++ are also adsorbed. Uranium, however, forms complex anions with sulfate, phosphate," Carbonate"~"~ and even with chloride if the solution is strong enough.15 These anions can be adsorbed by anion exchange resins. The strong base anion exchangers have a very strong preference for these complexes and hence this adsorption is very selective. In this paper, the examples concern acid sulfate leach liquors from which uranium is adsorbed as UO,(SO,),-% and UO,(SO,),". Materials and Equipment Ion Exchange Material—Ion exchange materials include natural and synthetic; organic and inorganic; cationic and anionic; and weak, intermediate, and strong varieties. They consist of fragments or beads normally in the size range —16 to $50 mesh. The newer varieties have been developed to have greater stability, chemical strength, and/or capacity than earlier varieties. The resin used for uranium recovery is a strong base anion exchanger.* To make * Such as Rohm and Haas Amberlite IRA-400 series, British Permutit DeAcidite FF. Permutit lonac SE. and Dow Nalcite SAR. this resin, styrene plus a few percent divinyl benzene are polymerized into long chains with occasional cross links. This resin in bead form is then reacted to introduce quaternary amine groups onto most of the aromatic rings.' These resins are water-avid gels of specific gravity of about 1.1, which shrink and swell by osmosis when the ionic content of the surrounding solution is changed. The beads which are shown in Fig. 1 can be broken like an onion by rapidly replacing 15 pct H,SO, with water. This organic gel can also be broken by mechanical handling as by a centrifugal pump. Otherwise it is remarkably stable. It is unharmed by fairly strong acid or alkali, oxidizing or reducing agents, and heat up to 70°C. The strong base resin when completely in the chloride form (with a chloride anion on each quaternary amine group) holds over 107 g of C1- per dry kg. As all these chloride ions can be displaced by other anions, the resin has an exchange capacity of over 3 g equivalents per dry kg. However, the resin is sold and used by moist volume. The moist resin contains about 50 pct water, weighs about 43 lb per cu ft, has 40 pct voids, and an exchange capacity of over 1 g equivalent per liter of bed volume. Ion Exchange Equipment—Ion exchange equipment used for recovery of uranium from leach solutions is substantially identical to that developed for water treatment and other applications.'" The resin beds are held in closed tanks or columns which, in the uranium plants, have been standardized at 7 ft diam and 12 ft high. The resin bed

Jan 1, 1958

By A. R. Troiano, A. B. Greninger

There is need for an adequate working hypothesis that would describe at least qualitatively the crystallographic mechanism for the transformation from austenite to martensite in steel. A general theory would not only be of great assistance in the correlation of existing data and in planning future experimentation, but would also form the basis for an eventual explanation of the property changes that accompany lattice transformations. The mechanism of martensite formation described in the following pages is the outcome of two new experimental determinations: (1) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite, and (2) the measurement and analysis of the change in position that a volume of austenite undergoes when it transforms into a crystal of martensite. For this latter study, the stereographic analysis of shear was employed; this method greatly simplifies the solution of lattice-shear problems, and some space is devoted to its description. Lattiice Relationships and Habits PREVIOUS WORK The lattice relationships between austenite and martensite in carbon steels have been studied by Kurdjurnow-and Sachs,' and by Wassermann;2 and in iron-nickel alloys by Nishiyama.3 Wassermann,2 and Mehl and Derge.4 The studies by Kurdjumow and Sachs and by Wassermann were made on single (austenite) crystals of quenched 1.4 pct carbon steel, and the results of these two independent studies agree closely with the postulated lattice relationships: (III)r||(0ll)a [101]r [111]a [1] Both Nishiyama and Wassermann worked with an alloy of iron plus 30 pct nickel (all austenite at room temperature), and "martensitic alpha" was formed by cooling in liquid air. They agree that the lattice relationships for these conditions are: (lll)r||(011)a [112]r[011]a [2] Mehl and Derge worked with a range of iron-nickel alloy compositions centered about 30 pct nickel. They concluded that when the transformation takes place near room temperature or above, relationship [l] holds, but if the same specimen is made to transform at -195°C, relationship [2] obtains;intermediate temperatures evidently produced a combination of these two relationships. Sachs and co-worker~,1,7 as well as Nishiyama,3 have proposed transformation mechanisms for martensite formation.* Both of the mechanisms picture the transformation as initiated by shearing movements along the octahedral [Ill] plane of austenite, followed by suitable expansion and contraction to complete the transformation. These mechanisms have been described and commented upon by Mehl, Barrett, and Smith,8 Mehl and Derge,4 Wassermann,2 and others, and generally accepted by investigators in this field. Greninger and Troiano9 have recently published the results of a detailed study of the shapes and orientation habits of martensite crystals in plain-carbon and nickel steels. They found that, contrary to previous assumptions, martensite plates form not along the octahedral planes but along austenite planes of very high indices; these results were in line with those of previous studies of martensite reactions in nonferrous alloy systems by Greninger and coworkers.6,10 Greninger and Troiano concluded that the transformation theories of Kurdjumow and Sachsl and of Nishiyama3 are untenable. Phragmén11 reached a similar conclusion. EXPERlMENTAL METHODS The object of this particular study was the evaluation of (1) lattice relationship between austenite and martensite, and (2) relationship between the martensite lattice and the martensite plate. The technique used for solving these problems was similar to that used by Greninger6 on martensitic structures in 8 copper-aluminum alloys. Briefly, the method consists of grinding and polishing a specimen on a surface parallel to an individual martensite plate and thus exposing a single martensite crystal for an area of l to 3 mm. The orientation of this exposed martensite crystal is then determined by means of a back-reflection Laue X ray pattern.12 Another pattern is obtained from the matrix crystal, and a stereo-graphic plot of data from these two patterns then provides the solution to the problem. It is necessary to repeat this process on several crystals in order to determine whether or not the solution is unique.

Jan 1, 1950

By J. O. Edstrom, G. Bitsianes

Parabolic rate constants were determined for the formation of wiistite by the solid state reaction between magnetite and iron. The reaction was diffusion controlled and inert marker studies indicated that the mass transport through the wiistite layer was accomplished by means of iron migration. Relationships between rate constants and self-diffusivities are discussed. The transport capacity for iron through dense wustite layers was found to be sufficient to carry on reduction, even in gaseous reduction processes. REDUCTION of iron oxides has been the subject of many investigations. Most of the work, however, has been done on rather crude material and there have been difficulties in correlating the data on a quantitative basis. The reverse process of the oxidation of iron has been studied more thoroughly and usually by starting from the pure metal. As a result, the mechanisms of oxidation are now fairly well known.It has generally been found that the oxidation of metals follows the so-called parabolic 1aw;Q hat is, when the oxides are formed as dense layers, their thicknesses are proportional to the square root of the reaction time. This parabolic law follows directly from Fick's first law of diffusion The flux, J, is defined as the quantity of diffusing substance passing per unit time through unit area of a plane at right angles to the direction of diffusion. This flux is proportional to the concentration gradient of the diffusing substance, and the factor D, known as the diffusion coefficient, is introduced as the proportionality factor with dimensions of (length)'/time. If the flux is measured as the increase of thickness of the oxide layer (Ax) per unit time (t) and the assumption is made that the concentrations of the reactants at the phase boundaries of the layer are independent of time, Eq. 1 reduces to Integration of this expression yields the parabolic function ax = k . t. [31 The product of the diffusion coefficient and the concentration difference across the oxide layer is included in the constant k. When iron is exposed to a highly oxidizing atmosphere, the oxide phases are formed normally in a topochemical fashion, i.e., the interfaces between the phases maintain parallel positions to the original surface of the specimen. Above 570°C, the phases are orientated usually in the order of iron, wiistite, magnetite, and hematite, a condition in conformance with the requirements of the Fe-0 system. Below 570°C, the wiistite phase is unstable and has not been found as a normal constituent in the oxidation products of iron. There is a strong probability that continuous layers of the solid oxides are formed as the specific volumes of the phases increase in direct order from iron to hematite.' , ' Regarding mass transport through dense solid oxide layers, Wagner' has postulated that diffusion in oxides generally may be interpreted as migration processes of ions and electrons. There must be normally a concentration gradient across the growing oxide layer for diffusion to occur. This condition requires that there be deviations from the ideal stoi-chiometric composition of the oxide and accordingly deviations from the strict order of an ideal lattice. Such "lattice defects" include interstitial ions, cation and anion vacancies, quasi-free electrons, and electron holes and are decisive for all migration processes.' Cations, anions, and electrons all may have some mobility in the oxides but the movement of one of the particles generally far exceeds that of the others. Previous work', 1,2,7 has shown that during the oxidation of iron the migration through the wiistite layer, and probably also the magnetite layer, is confined to the movement of iron ions. Migration through hematite, however, has been found to take place by oxide ion movement. These behaviors are in direct agreement with the type of vacancies present in the respective oxides. Reduction of Iron Oxides The gaseous reduction of iron oxides, like the oxidation of iron, takes place in a topochemical fashion at distinct interfaces between the appearing phases."-'" Porosities might be expected in these reaction products, since their specific volumes are less than that of the starting material. Frank and van Der Merwe" have shown, however, that it is theoretically possible for nonporous layers to form if the degree of misfit in specific volume is less than about 15 pct. These aspects on porosity formation

Jan 1, 1956

By D. R. Wieland, A. N. Barron, A. R. Hendrickson

A definite relationship has been found between the reactivity of flowing hydrochloric acid and its shear rate in a carbonate fracture. Both flow velocity and fracture width affect the acid reaction rate. Laboratory studies were conducted on acid reactivity at different flow velocities through horizontal-linear fractures, using 15 per cent hydrochloric acid at 80' F and approximately 1,100 psi. Fracture width varied from 0.02 to 0.20 in. These data provide a new basis from which the spending time and penetration of the acid can be estimated. Equations were derived expressing the relationship between injection rate, fracture width, acid concentration, time and fracture height, for linear and radial fracture systems. Because the penetration of the acid before spending is closely related to the extent of productivity increase resulting from an acidizing treatment, these data provide a valuable insight into some of the controlling factors that must be taken into consideration during treatment preplanning. INTRODUCTION Acidizing of carbonate reservoirs to improve production characteristics has been widely practiced since 1932. Originally, it was assumed that the acid uniformly penetrated natural formation pores and flow channels, enlarging them and thereby increasing their flow capacity. Little consideration was given to the reaction rate of the acid, or how far it would penetrate away from the wellbore into the formation, before spending. It has been shown recently' that, unless fractures are present in the rock, very little penetration is attained before spending, and the benefits of the acidizing treatment are largely confined to the immediate vicinity of the well-bore. Therefore, acid treatments may be classified into two categories: (1) matrix acidizing, in which the acid flows through multiple: formation pores; and (2) fracture acidizing, in which the bulk of the acid travels through fractures in the rock, whether natural or induced. When acidizing treatments are conducted at pressures of sufficient magnitude to open and extend such fractures, it is often desirable to inject a propping agent to hold the fracture open after the treating pressure has been released, thus providing a highly conductive flow channel through the rock. In some cases where acid attack produces surface irregularities, the resulting flow passages can be sufficient to provide high conductivity without use of a propping agent. During injection, the acid dissolves the carbonate rock with which it comes in contact until it is spent. Deeper penetration of the spent acid into the formation produces no appreciable benefit (if no propping agent is used) because the unetched fracture faces will rejoin when treating pressures are released and the fracture will "heal", with negligible resultant conductivity. The spending time of the acid thus becomes important in determining how far from the wellbore the improved-conductivity zone extends. The spending time of acid after injection into carbonate rock depends on the rate at which the acid reacts with the rock. This in turn is controlled by a number of factors, as previously reported. 2-4 These include temperature, pressure, acid concentration, rock composition, injection rate and the area-volume relationship between the acid solution volume and the surface area of the formation flow channels through which it penetrates. Thus, in matrix acidizing, where an extremely large area is exposed to the acid, spending is rapid. In contrast, spending time is prolonged in open fractures, where the area-volume ratio is much lower. Thus, greatest penetration of the acid before spending will be achieved in acid-fracturing treatments where fractures are held open by hydraulic pressure. Perkins and Kern5 have presented equations for fracture-width determinations which, for hard formations such as limestone or dolomite, indicate that high injection rates and viscous fluids are required to create wide fractures. Increasing the injection rate will, in itself, produce faster reaction rates. Because this type of reaction can be considered to be first-order diffusion-controlled, '-' the rate of movement of fluid past the rock surface affects the thickness of the diffusion layer, in turn affecting the reaction rate. Staudt, et al,10 report the results of tests in which a rotating marble cylinder was immersed in acid, and the weight loss at different speeds determined. Such test conditions, however, are not truly indicative of the situation in a formation during an acid-fracturing treatment. This paper reports reaction-rate data obtained under

By R. H. Edsal, G. Horvay

The transient one-dimensional heat-conduction equation is solved for two semi-infinite media, at different initial temperatures, brought into (poor) thermal contact. It is shown that the two interface temperatures gradually approach the well-known, instantaneously assumed, common interface temperature of the case of zero contact resistance. The present analysis, with slight modifications, may be used in fair approximation also for the class of problems involving a change of phase. One particular application of the boundary value problem solved in this paper concerns the determination of the temerature distribution in metal castings and molds.P This problem has been treated extensively by analytical methods (see e.g., the literature listed in Refs. 1 to 4) by electrical analogs (see e.g., Refs. 11 to 14) and also by experimental methods (see the literature listed in Refs. 4, 5), but prior to the work of Pellini and Ruddle the experimental results were rather unreliable. Immediate motivation for the work described in this paper was to better understand the results of Pellini,' which are typified by the curves of Fig. 1. Pellini cast 20-in. high, 7-in. sq steel ingots into cast-iron molds of various thicknesses. He measured the temperatures at mid-height, at a number of stations in the casting and the mold, and obtained the cooling curves shown in Fig. 1. The most conspicuous thing about Fig. 1 is the large temperature discontinuity at the interface between casting and mold, due presumably to the shrinking away of the casting from the wall and the attendant creation of an airgap, as the casting cools. Such a contact resistance slows down the anticipated freezing rate; an analytical prediction of this is of much interest in foundry practice. The determination of the effect of contact resistance in the presence of a change of phase will be dealt with, by an approximate method, in a separate paper.' In the present paper the much simpler problem is considered in which there is contact resistance but no change of phase. This problem frequently arises in the analysis of aircraft structures.+ It can initial temperature, and may be regarded as semi-infinite. We suppose the thermal properties in the two media to be time, temperature, and space independent; there are no sources or sinks within the media. In Fig. 2(a) we illustrate, schematically, the case of no contact resistance. The semi-infinite media "0" and "2:' initially at temperatures 8 (- m) and 8(+ -), respectively, are brought into contact at time t =0. A common interface temperature 8,i = is instantaneously established, and thereafter remains constant. Temperature curves are drawn for three instants of time. When there is contact resistance between the two media, the temperature equalization occurs as sketched in Fig. 2(b). Fig. 2(c) illustrates a temperature curve, using the dimension-less notation Barber-Weiner-Boley6 have stated the equations [23a, b] given below, which govern the heat transfer in the two media, and solved them for a rather complicated special case. In their example both media "O" and "2" are finite, are insulated at their far ends, and there is steady heat input into medium 2. In Eq. [27] we give the general solution of the most important special case, where the two media are semi-infinite and there are no sources or sinks. In this case the results may be stated in simple closed form. In Fig. 3, to be discussed in the next section, we illustrate the variation of the interface temperature when steel at 2760" is brought into contact with iron at 100". This example, if we disregard the effect of the heat of fusion, is comparable to Pellini's experimental results, Fig. 1. (Unfortunately, however, experimental determination of the interface temperatures was difficult to carry out, and hence Fig. 1 is not very accurate near the interface.) In Figs. 4 and 5 of the following section, we similarly compare Pellini's sandcasting tests with analytical results for the case where steel at 2760" is brought into contact with sand at 100". It will be pointed out that, insofar as the interface temperatures are concerned, heat of fusion has a minor effect, and so the present approximation, with small modifications, may be

Jan 1, 1961

PRESIDENT WHITESIDE: If the chair may be pardoned, he would like to say he knows something of the work of this committee, and I assure you that they have all worked faithfully and hard, holding meetings at least every other day, and sometimes oftener, hustling money and going through all the different work necessary to bring about and to make a successful occasion of this kind, and I-who really acted as an outsider and viewed their work-was certainly appreciative of their efforts, and I know you would have been had you been able to see how hard they all worked. One of the sad things in life always is when one becomes a "has-been." I have been more or less active in the work of the Institute ever since its in¬ception. Just why the high honor of President was conferred upon me I have never been able to fathom, but my time is about over and I am about to join the "has-beens," and while the position naturally has entailed a certain amount of work, it has been very pleasant work, and when one has the hearty co-operation of his fellow workers, such work is always a pleasure. It is, therefore, with a certain amount of regret that I lay down the gavel and take it up again to present to my successor; but in doing so, I wish to thank you, one and all, for your very hearty help and co-operation, and to wish my successor, Mr. George B. Pryde, all the possible success that can be his. Mr. Pryde. (Applause.) MR. PRYDE: I will make no extended speech at this time. I think possibly the next year I will have enough opportunity to do that; but I had a letter from my friend, Murphy, before this meeting, and he thought we were going to have a very good meeting; but I don't know the motive behind his letter. (Laughter.) I remember the story about the Scotchman who went to see the doctor, and the doctor said: "Sandy, you drink any?" "Oh, yes." "Well," he says, "you have got to cut that out. Do you smoke?" "Oh, yes; I smoke a great deal." "Well, you will have to cut that out also." And Sandy picked up his hat and started for the door. "Wait a minute, Sandy; you haven't paid me for my advice." "Yes, but I am not going to take your advice." (Laughter.) But I am deeply appreciative of the honor you have conferred upon me, electing me to be head of this Institute for the next year. I have belonged to this Institute, I should say, ever since it has been organized. This present session especially has been a very good session. As I look back over the different meetings, I think this one stands out among all the others in the papers presented and the spirit of co-operation that prevailed among the members here, and I am not going to ask your co-operation during the year; I am sure I will get it from all of you. I want to thank you for the honor conferred upon me. (Applause.) MR. WHITESIDE: The retiring President did not quite follow the reading of the by-laws, I think, in which it says that immediately after the election of a new President, the new President shall assume office, and I got so busy I forgot all about that. The committee which the chair decided to appoint is as follows. This is to formulate safety rules: For Utah, John Crawford, William Littlejohn; for Wyoming, Peter Patterson, Glen Knox; for New Mexico, William Risdon, Allan French; for Colorado, James Dalrymple, J. C. Roberts; and last and surely not least, as chairman of the committee, Mr. George B. Pryde. (Mr. Pryde later appointed D. Harrington as a member-at-large.) C. M. GODDARD: Mr. Chairman, we all realize that in a gaseous mine the application of, safety measures transcends everything else. Machinery is installed 100 per cent safe, as they might say, to take care of any condition

Jan 1, 1923

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

The Sao Chico gold project is located on the Tocantinzinho trend which is the most mineralised zone in the Tapajos Mineral Field of Brazil (see Figure 1). The Tapajos goldfi eld was the site of the biggest gold rush in Brazilian history in the late 1970s and 1980s when approximately 500 000 garimpeiros (artisanal miners) rushed to the area to exploit extensive areas of newly discovered alluvial gold. Approximately 20 - 30 million ounces of gold were produced from these operations before the easily won alluvial gold deposits were largely depleted. The Tapajos region has had little exploration by modern exploration methods compared to any other equivalent gold fields in the world. The gold occurs in sulfide veins developed in shear zones within Proterozoic granites. Gold grades vary from approximately 15 g/t in the hard rock veins, to up to several ounces per tonne in the supergene weathered upper portions of the veins. Goldbearing vein zones in the weathered profile are free digging. In addition, tailings dumps from previous mining operations contain gold grades of approximately 1 g/t. Metallurgical test work conducted to date indicates that gold recoveries of at least 70 per cent can be achieved via gravity concentration. Gold Anomaly, via its 100 per cent owned Brazilian subsidiary, Gold Aura Do Brasil Mineracao Ltda (GOAB), plans to mine the tailings and weathered vein material by open cut methods to generate a quick cash fl ow and to provide a better understanding of the mineralisation as part of a feasibility study for mining the underlying sulfide zone mineralisation (see Figure 2). Mining will utilise locally hired excavators and trucks and ramp up to a rate of 100 tonnes per day. To treat the gold-bearing material, GOAB has purchased an integrated 'state of the art' gravity concentration processing plant from Gekko Systems of Australia. The processing plant includes a scrubber for clay and oversize removal, coarse gold gravity separation via an inline pressure jig and an inline spinner; and fine gold gravity separation via a Falcon Concentrator. The plant is expected to be operational by late 2010. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 11/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond delays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of 1/2 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock. In the early blasts with millisecond delays it was observed that instead of the usual sharp report, the blast had a muffled sound and vibration was not as perceptible as when simultaneous firing was used. Because many quarry operators were being threatened with injunctions or suits for damages by neighbors who claimed structural damage to their buildings, millisecond delays were tried extensively in quarries. In the majority of these trials, the results were very satisfactory. The seismologists recorded the ground movement created by many blasts and verified the initial observations that millisecond delays could be used to reduce vibrations appreciably. In the past few years the advantages of this principle of nonsimultaneous firing of the charges in blasts has become generally accepted. Today the quarry operator who has vibration troubles, inadequate breakage, and excessive backbreak and has not investigated the possibilities of millisecond delay blasting is ignoring a remedy that has proved satisfactory for many. His complacency may be costing him money. Because of the results attained in quarry blasting, it was logical that millisecond delays should be tried in construction work such as in road cuts. As formations in this type of work are likely to change rapidly with advance of the cut, it is more difficult to evaluate results than in quarry blasting. However, this improved control over timing has been beneficial in limiting throw, promoting fragmentation, and reducing overbreak. In blasting near buildings the reduction in vibration and in throw has been especially helpful. As blasters employed in construction work learn what may be accomplished by closer control over the time of firing of explosives charges, more and more millisecond delays are being used to supplant instantaneous electric blasting caps. Improved Fragmentation Underground With this background of promising results, it was not surprising that millisecond delays should go underground. In limestone mining use of millisecond delays as compared with use of cap and fuse or electric blasting caps showed improved fragmentation in stopes and in slabbing operations. Then an opportunity developed to use millisecond delays in some tunnels being driven in a limestone mine (fig. 1). Using the normal charge employed and merely substituting three millisecond delay periods for three regular delay periods, there was a noticeable difference in the appearance and the position of the pile of rock after a blast. A greater portion of the face was exposed, the crest of the pile was farther from the face, and the pile was heaped high along the center line of the tunnel leaving room to walk along the ribs to the face. Fragmentation was appreciably increased. It gave the impression that the slabs had been thrown against each other with tremendous force, promoting the movement of the broken rock along the center line of the tunnel away from the face. Because the drilling and the charge weights were unchanged, the evidence was convincing that the difference in timing was responsible for the difference in results. Probably a greater portion of the energy from the explosives had been expended in doing useful work on the rock. Zeros followed by two periods of millisecond delays were used in the V cut and in two slabs to either side of the cut in this simple round. When millisecond delays, substituted period for period for regular delays, are first tried in a drift round in a mine, and the usual charge of explosives

Jan 1, 1951

By J. H. Swisher

The solubility of graphite in CaO-S2O2-Al,O3 slags was measured by equilibrating slag samples with graphite crucibles and CO gas. Carbon contents as high as 2 ut pct were obtained in CaO-saturated, CaO-A1,O3 slags, and 1.3 wt pct in slags of the composition CaO.Si0,. Although the observed conditions for Sic formation were in agreement with those predicted from thermodynamic data, CaC, was found to form at a lower temperature than predicted frotn thermodynamic data. From measurements of the equilibrium carbon content as a function of CO Partial pressure, it was found that carbide ions dissolve in CaO-A12O3 melts with a valence of minus two. The carbon content increased with CaO concentration in Ca0-Al,O3 melts and increased with SiO, content along the CaO'AlO3-CaOSi0 join in the ternary system. When solid CaC2 was added to CaO-A12O3 and CaO-SiO2-A12O3 slags, it was found that one of the oxides in the slag was reduced by the carbide (Al2O3 in the forrner and SiOz in the latter). In electric furnace steelmaking, a double-slag practice is frequently used to meet alloy specifications. Initially a flush slag, which is oxidizing in nature, is used to remove phosphorus and carbon from the steel bath. Later in the refining period, the flush slag is replaced by a highly reducing carbidic slag. When calcium carbide is formed in or added to a finishing slag, the slag is effective as a desulfurizing agent and also permits alloying elements such as chromium, vanadium, and tungsten to be added to the slag in the form of oxides. The oxides are readily reduced by calcium carbide, thereby minimizing the use of expensive ferroalloys. More work has been done on the thermodynamics of silicon carbide in slags than on calcium carbide. Baird and alor' and Kay and alor' determined the free energy of formation of Sic by measuring the partial pressure of CO in equilibrium with solid silica, silicon carbide, and graphite. Using a similar technique, they determined SiOz activities in CaO-SiOz and Ca0-Si0,-A1203 slags. Rein and chipman3 also determined the free energy of formation of Sic using slag-metal equilibrium measurements. A literature survey has uncovered only one experimental study of the behavior of CaC, in slag systems. Shanahan and cooke4 report the results of some preliminary experiments on the solubility and stability of CaC, in a CaO-A1,03 and a Ca0-Si0-A1,03 slag at a temperature of about 1500". The carbon solubility as CaC, in a slag containing 50 pct CaO and 50 pct A1203 was reported to be 0.6 pct. They also review earlier work on the binary CaO-CaC, system. A eutectic exists in this system, but various investigators disagree on the eutectic temperature and composition. eal has given an explanation for carbide furnace erruptions in terms of the thermodynamic properties of CaC,; his analysis is not based on experimental data, but on compiled data for the free energies of formation of CaC, and CO.' , These data for steel-making temperatures are all extrapolated from the results of low-temperature measurements. In the experiments described in this paper, slag samples were equilibrated with graphite crucibles and with mixtures of CO and argon or with CO gas at 1 atm total pressure for measurement of the carbon solubility. Most of the work was done on Ca0-A1203 binary slags, although in some experiments CaO-SiO, and Ca0-Si0,-A1,03 slags were used. EXPERIMENTAL Slag samples of the desired composition for the solubility measurements were obtained by blending pre-fused master slags. The master slags were prepared by fusing mixtures of reagent-grade CaC03 with either A1,03 or Si0, in a graphite crucible. The master slags were crushed, then decarburized in air in a muffle furnace at 1200O C. A schematic diagram of the apparatus is shown in Fig. 1. The source of carbon for the solubility meas-

Jan 1, 1969

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don't use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By R. A. Holmes

Although manganese is a metallic element and is widely dispersed in nature, it never occurs except as a compound in combi¬nation with other elements. Use of such compounds in the production of glass is known to have occurred in early Egypt. The dioxide of manganese was considered a compound of iron until 1774 when C.W. Schule first recognized it as an element. In the same year, a Swedish mining engineer, J.G. Gahn, became the first to isolate manganese. In 1856 development of the Bessemer process of steelmaking gave economic importance to manganese, and later, in 1882 Robert Hadfield discovered the benefits of high manganese steels. GEOLOGY Physical Properties Elemental manganese is a silver-gray metal, resembling iron but harder and more brittle and used primarily in alloys (both ferrous and non-ferrous) and a wide variety of chemical compounds. Some of the physical properties of manganese include: melting point¬1 245°C; boiling point-2 150°C; density at 20°C-7.43 g/cm3; specific heat at 25.2°C-O.115 cal/g; latent heat of fusion-63.7 cal/g; hardness on Mohs scale-5.0; linear coefficient of thermal expansion from 0 to 100°C-22 x 10-6. Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are pre¬dominantly manganese to those having only minor percentages of manganese. Distribution of Deposits Manganese ore deposits are found worldwide and were formed in various geological environments, but only a rather limited num¬ber of deposits have high grade manganese ore in sufficient quan¬tities to be mined and utilized economically on an industrial scale. It is worth noting the fact that almost all of the significant deposits can be classified into two types of deposits: marine chemical sed¬imentary deposits, and residual (secondary) enrichment deposits. There are, however, a much larger number of geological types but these are not of commercial significance at this time. Sedimentary deposits are the most common and are usually stratiform or lenticular. Manganese minerals were formed by a chemical process during the deposition of marine sediments. They usually contain manganese oxides and carbonate minerals, some¬times interbedded together or with other sedimentary rocks such as limestone or shale. Examples of this type of deposit are the Russian ore bodies of Nikopol and Tchiatoura, as well as the Kalahari deposits in South Africa and deposits of Groote Elyandt in Aus¬tralia. Residual deposits were formed in a different way: by alteration of existing manganese deposits or by concentration of the manga¬nese minerals when other minerals were washed away by weath¬ering or ground water processes. The Nsuta deposit in Ghana, the Amapa deposit in Brazil, the Moanda deposit in Gabon, and nodules in the residual clays of the US Southern Appalachians are examples of this type of geological process. In the case of the Ghana and the Amapa deposits, this is only true for the outer layers of the deposit containing oxide minerals, the inner part being comprised of car¬bonate minerals including manganese carbonate, probably from marine origin. Some sedimentary and residual-type deposits have been metamorphosed, giving rise to small high grade ore bodies. These deposits are regionally metamorphosed, occurring in mar¬bles, slates, quartzites, schists, and gneisses. Some of these deposits, such as the Franklin, NJ, deposit are rich enough to be commercial without secondary enrichment; however, most of the exploitable deposits have been secondarily enriched. Due to the diversity and complexity of manganese deposits, both with respect to deposition and chemistry, a wide range of impurities are almost invariably present in the ores. Table 1 shows that the reserves (i.e., a measured resource that can be economically and legally extracted) are estimated at 814 x 106 tons of contained Mn, which equates to more than a 100 year supply at the current level of production. The reserve base is made up of the marginally economic reserves and sub-economic re¬sources and are some 4.5 times greater than the proven reserves. Also apparent from study of Table I is the fact that some 75% of manganese reserves are found in two countries, the USSR and South Africa. On the other hand, North America (i.e., the United States and Canada) have few significant deposits. The largest deposit, or at least one of the largest, in the United States is located at Chamberlain, SD. This deposit is sedimentary

Jan 1, 1994

By T. L. Chu, G. A. Gruber

Silica films hare been rleposited 011 silicon substmtes at 400° to 600°C by a chemical-transport technique using hydrogen fluoride as the transport agent ill a closed system. This transport takes place from a source materia1 1071: temperature to substrates at higher temperatures, as indicated by the thermochemistry of the transport reaction. The experimental variables of- the transport process, such as the substrate temperature, the pressure pi the transport agent, and so forth, have been studied. The rate -determining step of the transport process appears to he the ),ale of chemical reaction in the source region. The transported films are similar to thermally grown silica films in physical proper-ties with the exception of 'some what higher dissolrrtion rates. SILICA films deposited on suitable substrates serve many purposes in electronic devices. They are used for the fabrication of tunneling devices, the surface passivation of devices, and the shielding of devices from nuclear radiation: and as selective masks against the diffusion of specific impurities into semiconductors. Doped silica films can also be used as sources for the diffusion of impurities into semiconductors. Several oxidation and deposition techniques for the preparation of silica films have been developed to meet the requirements of these applications. The therma1 oxidation of silicon by oxygen or steam at temperatures above 900 C is commonly used in silicon technology. The deposition techniques are perhaps more advantageous since they usually require lower temperatures and are not limited to silicon substrates. Silica films have been deposited on silicon and other substrates by reactive sputtering and chemical reactions. The sputtering of silicon in an oxygen atmosphere is capable of depositing good-quality silica films on silicon' and gallium arenide. Many chemical reactions are known to yield silica at room temperature or higher. These reactions may involve intermediate steps. However, the final step yielding silica should take place predominately on the substrate surface in order to produce adherent films. When silica is formed in the gas phase by volume reactions, no adherent deposit can be obtained. Generally, the experimental conditions of a reaction can be varied so that the surface reaction predominates over the volume reaction. The chemical reactions which have been used successfully for the deposition of silica films are briefly as follows. The pyrolysis of alkoxysilanes in an inert atmosphere or under reduced pressure has been employed to deposit silica films on germanium3 and silicon4 at 650" to 750°C in a flow system. The deposition of silica films from alkoxysilanes has also been achieved at nearly room temperature by a low-pressure plasma. Device quality silica films have been deposited on germanium and gallium arsenide by the deposition of an amorphous thin silicon film followed by oxidation at 600" to 700" . Silica films for high-temperature capacitors have been produced by the hydrolysis of silicon tetrabromide at 950°C in argon and hydrogen atmospheres.7 We have developed a chemical-transport technique for the deposition of silica films on semiconductor substrates at relatively low temperatures. The thermochemistry of the transport reaction, the experimental variables of the transport process, and the properties of the transported silica films are described in this paper. THERMOCHEMICAL CONSDERATIONS The transport of solid substances by chemical reactions in the presence of a temperature gradient has been used for the preparation of films and crystals of many electronic materials. In this technique, a gaseous reagent is chosen so that it reacts reversibly with the solid substance under consideration to form volatile products. Since the equilibrium constants of most reactions are temperature-dependent, the transport of these products to regions of suitable temperature in the reaction system would cause the reverse reaction to take place. depositing the original solid. When the equilibrium is shifted toward the formation of the solid as the temperature is decreased, the solid is transported from a high-temperature zone to a lower-temperature region, and vice versa. This chemical-transport technique can be carried out in a closed or gas-flow system. In a closed system, chemical equilibrium is presumably established in the different temperature regions of the system, and the transport agent regenerated in the deposition region repeats the transport process in a cyclic manner. The local chemical equilibrium may not be approached in a flow system: however, this system offers a greater degree of flexibility. Silica reacts reversibly with hydrogen fluoride and this reaction was chosen for the transport process. The over-all reaction between silica and hydrogen fluoride may be written as: SiO2(s) + 4HF(g-) = SiF4Ur) + 2H2O(^)

Jan 1, 1965

By E. C. W. Perryman

The wide grooves formed at the grain boundaries when high purity aluminum is attacked by hydrochloric acid or sodium hydroxide have been attributed by earlier workers to the high energy of the grain boundary material. The effect has been investigated for high-purity AI-Fe alloys with up to 0.055 pct Fe as a function of iron content and heat treatment. It is shown that the explanation given above is untenable, but that the results can be explained on the assumption that iron segregates to the grain boundary in solid solution. IN 1934, Rohrmann¹ showed that aluminum of 99.95 pct purity suffered intercrystalline corrosion when immersed in 10 to 20 pct hydrochloric acid, and that the susceptibility to intercrystalline corrosion depended upon the heat treatment given. The greatest susceptibility was found for specimens quenched from a high temperature (600°C) and the lowest susceptibility for specimens cooled slowly from that temperature. Lacombe and Yannaquis2 have shown that super-pure aluminum (99.9986 pct) annealed at 600°C suffers intercrystalline attack in 10 pct hydrochloric acid and that this attack is intensified by anodic dissolution in the same solution at a current density of 10 milliamperes per sq dm. No difference in extent of intercrystalline attack was found between the 99.993 and 99.986 pct Al, which led the authors to suggest that impurities played only a secondary role in the mechanism of intercrystalline corrosion. It was found, however, that the attack at the grain boundaries depended upon the relative orientation of the grains, large differences in orientation favoring rapid attack. Boundaries where the two neighboring grains were similarly orientated showed high resistance to attack as did boundaries between grains which were in twin relationship. These observations led Lacombe and Yannaquis to suggest that the intercrystalline attack was due to lattice discontinuities present at grain boundaries. Assuming that the grain boundary is a layer three to five atoms thick and has a crystal structure which is a compromise between the two neighboring grains it is clear that the discontinuities will increase with increasing difference in orientation between the neighboring grains and hence the increasing tendency to intercrystalline attack. Roald and Streicher³ investigated the effect of heat treatment of aluminum alloys ranging in purity from 99.2 to 99.998 pct on the corrosion resistance in 20 pct hydrochloric acid and 0.30N sodium hydroxide. They found that in hydrochloric acid the intercrystalline attack appeared to be determined by the type and quantity of impurities present and by the relative orientation of the grains. No difference in the susceptibility to intercrystalline attack was observed between specimens quenched and those furnace cooled, from 575°C. In 0.30N sodium hydroxide some materials exhibited intercrystalline attack, this taking the form of V-notches. Rohrmann¹ offered no explanation for the greater susceptibility to corrosion of material quenched from 600°C. It seems possible that this difference is connected in some way with a different distribution of impurity elements in the quenched and slowly cooled specimens. The fact that Roald and Streicher8 observed no difference between quenched and slowly cooled specimens may possibly be due to differences in either rate of cooling or silicon content or possibly both. Both these would be expected to have an effect on the distribution of impurity elements. Although the rate of cooling used by Rohrmann was slightly more rapid than that used by Roald and Streicher the position cannot be clarified because Rohrmann does not give the silicon content and Roald and Streicher give the silicon contents of only a few of their alloys. That Lacombe and Yannaquis2 found no difference in corrosion behavior attributable to impurities between the two materials they used may be because both were of high purity compared with the aluminum used by Rohrmann.¹ Although they found no difference in the corrosion behavior of their two materials it is possible that the results obtained by Lacombe and Yannaquis may, nevertheless, have been influenced by impurity distribution, since, on the transition lattice theory of grain boundary structure, it would be expected that sparingly soluble impurities would tend to segregate to boundaries where the orientation difference is such that there is a greater density of atomic sites of suitable size to contain them. It was considered worth while, therefore, to examine the corrosion properties of a series of materials of differing impurity content with the objects of confirming the experimental observations made

Jan 1, 1954

By Robin O. Williams

Robin 0. Williams (Oak Ridge National Laboratory)— The authors have questioned the degree to which the coherency strains between the iron-rich and chromium-rich phases are isotropic as proposed in Ref. 5 on the basis of the difference between the elastic properties of the two phases. The relative magnitude of the stresses is determined by the moduli as shown by Eqs. [2], [3], and [4] of Ref. 34. However, the moduli of the two phases have no direct bearing on the uniformity of either the stress or strain within either phase. The idea that the strains are isotropic within each phase (but normally of different magnitude and always of different sign) is based entirely upon the experimental observation that X-ray line broadening has not been detected even when the particles become rather large. It has not proven possible to grow the particles sufficiently large that they lose coherency. Based upon this lack of line broadening one can estimate an upper limit for the nonuniformity of the strains within each phase as follows. It is considered possible to detect line broadening if it is as great as 10 pct of the separation of the K, doublet for the (211) line using chromium radiation. The doublet separation would correspond to a total strain of 0.0017 such that the total variation of lattice parameter relative to the average lattice is now k0.05x0.0017 or something less than ± * For the present case the strain in each phase is roughly 0.002 such that the variation of strain within a phase will not exceed 5 pct. It is stated that the expression derived for strengthening for the hydrostatic straining as observed in this system would substantially overestimate the magnitude due to dislocation flexure. This is contrary to the conclusion reached in the original paper34 for the present range of particle sizes. What is the lowest temperature at which a has been observed to form in this alloy? M. J. Marcinkowski, R. M. Fisher, and A. Szirmae (nutlzors' reply)— -Williams' arguments based on X-ray findings for a chromium-rich precipitate and an iron-rich matrix strained to a common lattice parameter are certainly convincing. This being the case, there are no shear components of strain associated with the precipitate-matrix aggregate to interact with the shear components of the dislocation stress fields, contrary to the opinion expressed by the present authors. On the other hand, the present authors, in spite of this error, did not expect the shear interactions to be significant. The chief objection to Williams' model in the present case is that the various segments of the dislocation line are assumed to pass from one potential valley to the next independently of neighboring segments. This is only true for a highly flexible dislocation line, i.e., one whose radius of curvature is something less than the center to center distance between precipitate particles which amounts to about 90A in the present alloy. In order to maintain this curvature, an externally applied shear stress of at least 230,000 lb per sq in. would be required or about four times the observed stress. It is therefore concluded that the dislocation lines move rather rigidly through the lattice. This being the case, the forces on the dislocation resulting from the hydrostatic interaction between the stress fields of the edge-dislocation components and the precipitate particles should average out to zero; that is particles above the below the slip plane produce forces on the dislocation of opposite sign and therefore will cancel when averaged over the entire length of the dislocation. On the other hand, since the dislocation is not perfectly rigid, Williams' model may lead to some strengthening, but far less than that predicted. A second and equally serious objective to using Williams' strengthening model for the present alloys is that profuse wavy slip due to the motion of screw dislocations played a predominant role not only in the unaged alloys but in the fully aged ones as well. Since the screw dislocation has associated with it only shear components of stress the hydrostatic strengthening model no longer applies. In view of these arguments the present authors must reject Williams' model of strengthening as being pertinent to the present alloy system. The present authors have made no detailed study of the lowest temperature at which a forms in the quenched ferritic alloys. None was ever observed n the alloys aged at 500°C so that forma-tion must occur at temperatures higher than this and was therefore not a factor in the present study.

Jan 1, 1965

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 11/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond delays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of 1/2 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock. In the early blasts with millisecond delays it was observed that instead of the usual sharp report, the blast had a muffled sound and vibration was not as perceptible as when simultaneous firing was used. Because many quarry operators were being threatened with injunctions or suits for damages by neighbors who claimed structural damage to their buildings, millisecond delays were tried extensively in quarries. In the majority of these trials, the results were very satisfactory. The seismologists recorded the ground movement created by many blasts and verified the initial observations that millisecond delays could be used to reduce vibrations appreciably. In the past few years the advantages of this principle of nonsimultaneous firing of the charges in blasts has become generally accepted. Today the quarry operator who has vibration troubles, inadequate breakage, and excessive backbreak and has not investigated the possibilities of millisecond delay blasting is ignoring a remedy that has proved satisfactory for many. His complacency may be costing him money. Because of the results attained in quarry blasting, it was logical that millisecond delays should be tried in construction work such as in road cuts. As formations in this type of work are likely to change rapidly with advance of the cut, it is more difficult to evaluate results than in quarry blasting. However, this improved control over timing has been beneficial in limiting throw, promoting fragmentation, and reducing overbreak. In blasting near buildings the reduction in vibration and in throw has been especially helpful. As blasters employed in construction work learn what may be accomplished by closer control over the time of firing of explosives charges, more and more millisecond delays are being used to supplant instantaneous electric blasting caps. Improved Fragmentation Underground With this background of promising results, it was not surprising that millisecond delays should go underground. In limestone mining use of millisecond delays as compared with use of cap and fuse or electric blasting caps showed improved fragmentation in stopes and in slabbing operations. Then an opportunity developed to use millisecond delays in some tunnels being driven in a limestone mine (fig. 1). Using the normal charge employed and merely substituting three millisecond delay periods for three regular delay periods, there was a noticeable difference in the appearance and the position of the pile of rock after a blast. A greater portion of the face was exposed, the crest of the pile was farther from the face, and the pile was heaped high along the center line of the tunnel leaving room to walk along the ribs to the face. Fragmentation was appreciably increased. It gave the impression that the slabs had been thrown against each other with tremendous force, promoting the movement of the broken rock along the center line of the tunnel away from the face. Because the drilling and the charge weights were unchanged, the evidence was convincing that the difference in timing was responsible for the difference in results. Probably a greater portion of the energy from the explosives had been expended in doing useful work on the rock. Zeros followed by two periods of millisecond delays were used in the V cut and in two slabs to either side of the cut in this simple round. When millisecond delays, substituted period for period for regular delays, are first tried in a drift round in a mine, and the usual charge of explosives

Jan 1, 1951

By Karl W. Mote, R. K. "Ivan" Urnovitz

One of the Northwest Mining Association's guide-lines is: "If you always do what you've always done, you'll always get what you've always gotten." Another way of saying this is, simply, "when the road curves, don't refuse to turn." Our industry has been roundly criticized for living in the old political world, and, I believe, justifiably so. Until about 20 years ago, members of both houses of Congress deferred to specialists among their members for mining legislation. This was true for all public lands and natural resource issues, and were referred to as the mining bloc, or the timber bloc, or the ranching bloc. We felt safe, and to a large degree, were safe in the sense that western members of the US House of Representatives and of the US Senate understood the need for multiple use of public lands, and the need for the natural resources they supply. They also knew what it takes to stay in business and how to create the economic atmosphere that encourages private industry to find and provide the natural resources. Almost daily, members of our industry bemoan the destructive effects that current regulations, let alone new proposals, are having on American industry. And, there are some intriguing aspects for us to ponder. First, the specific complaint about the government is not regulation per se, but rather that the rules or policies don't make sense. We recognize that few understand our industry, but we have assumed that the government will rely on people experienced and knowledgeable in the area being brought under government controls. There was a time that this assumption was valid, but it is no longer true since we have entered the era of the professional regulator. Much like the MBA who believes that a professional manager can manage anywhere, the new breed of regulator sincerely believes that process is the key to developing effective regulations or programs. They reason the process virtually assures that all the pertinent facts will inevitably come to light and, after receiving appropriate considerations, will result in the proper decision being reached and implemented. Unfortunately, following the process also allows politics to play a new and greater role than ever before, since information based on what can only be called weird-science can now be presented to the professional regulator and accepted as fact. Regulators do not have the background to question the basic tenets of the conclusion being presented to them. To add insult to injury, testimony from people in the industry involved, intended to set the record straight, is too easily discounted as being merely self-serving. A second aspect is that the question of why the associations aren't doing more to stop poorly conceived legislative and regulatory proposals, or to counter the ever-increasing influence of the selfappointed public interest groups is being increasingly discussed. This is occurring despite the fact that there is a higher level of involvement and closer cooperation between the various associations than ever before. This raises a most important question: where are we going wrong? In the last 20 years or so, major changes have taken place. A new philosophy, taking advantage of the public's recognition of need to protect our environment, has swept through the nation, resulting in a whole new body of law enacted to assure environmental protection. We all acknowledge the need to prevent undue degradation during the course of mineral development, and we all consider ourselves to be responsible stewards of the land, because we live and work in the outdoors and know the importance of environmental protection. The changes in the federal statutes apply now to every aspect of mineral discovery, development, and production, and assure adequate reclamation of lands when we are done. Along with the positive changes, are a constant barrage of attempts to stop public land use, or stop mining, or stop any new economic development, ostensibly to "protect the environment," but often reflecting a hidden agenda of social reform. These types of extreme, irrational, and just plain impossible proposals are everyday occurrences, but we have not geared up to challenge all the proposals which could end mining. Instead, we did what we always had done. The road turned, but we didn't. And we wondered why those who had always protected mining weren't doing their job, and why we were having such limited success in reining in the regulators. The Congress had changed, the public demands had changed, the recognition of importance of natural resources had

Jan 1, 1991