Search Documents

By L. Muhr, Y. -T. Tang, M. -O. Simonnot, B. Laubie, R. -L. Qui, Z. Chour

"Agromining aims at recovering metals from different secondary resources with hyperaccumulating plants. These natural plants can selectively concentrate metals at very high level and can be transformed to produce commercial compounds. The classical strategy to recover metals from hyperaccumulator plants is based on hydrometallurgy. It consists of: i) burning the plant to obtain ash, which is a very rich bio-ore without organic matter, ii) transferring the target element(s) into aqueous solution by acid leaching and iii) purifying the leach liquor to obtain the target element(s) in the desired form. This method has enabled us to obtain nickel salts, nickel oxide, zinc and cadmium from different plants. However, it is not possible to apply this approach to recover rare earth elements (REEs) from the fern D. dichotoma, growing on mine tailings in South China. Actually, this plant is very rich in silicon: plant burning gives an amorphous ash, very stable despite severe leaching conditions. Therefore, the strategy has been changed and processes are currently developed to extract REEs by direct leaching of the biomass, without burning the plant. Several conditions (i.e. leaching solutions) have been investigated, showing that a good extraction yield was obtained with HNO3 0.5 N (around 84%). This yield was increased to 99% by adding a complexing resin into the leaching solution. After two-steps of elution, results have shown that is possible to recover 75% of the REEs at 81% purity.INTRODUCTION The demand of rare earth elements (REEs) (including 15 lanthanides, yttrium and scandium) has been growing sharply over the past years, because of their industrial applications. REEs are essential elements for emerging technologies, and are used for example in permanent magnets, lamp phosphors or rechargeable batteries. China is the main producer, and the market supply became tense in 2010 when this country decided to limit exports of these elements. Exploitable mineral resources, as well as REE separation capacity are concentrated in a few countries (e.g. USA, Australia, Malaysia, France), which increases the supply risk. Therefore, these elements are considered as critical raw materials (CRM) for many countries and especially for EU (Fortier and Gambogi, 2017)."

Jan 1, 2018

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977

Track and control the tram maneuvers of continuous mining machines by developing and evaluating a laser sensor system. Background Progressive technology has the potential to greatly improve mine-worker safety, helping to create a safer, better working environment for mine workers by keeping them away from the dangerous face area. To benefit from such technology, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A cornerstone for computer-assisted operation is an effective guidance system. Since there are no guidance systems on any commercial continuous miners (CM's), the Bureau it-self developed and tested a laser-based sensor system, based on a commercial sensor called Lasernet. The laser-based guidance system employs four laser scanning sensors at fixed locations in a mine entryway to report the angular coordinates of two cylindrical retro-reflective targets mounted on a CM. Using triangulation, a real-time microcomputer system processes the sensor data and updates the xy position and heading (h) of the CM five times per second. Using a simple control algorithm and communications interface to the CM control computer, the system also controls rotational and translational tram maneuvers.

Jan 1, 1992

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D McKeon

In July 2006, ten Mining Engineering students and Associate Professor David Laurence from the University of New South Wales (UNSW) participated in the universityÆs inaugural overseas mining field trip. The ten-day trip to western Canada involved visits to two mines in British Columbia, the Diavik Diamond Mine in the Northwest Territories and the Syncrude oil sands operation in Alberta. Importantly, the groupÆs main objective was to gain a global understanding of todayÆs mining industry by observing the different cultural, legal, social and environmental setting found in Canada. It should be noted that the entire trip was planned, organised and directed by the students and benefited from extensive industry support both in Australia and Canada. This report intends to provide an overview of the field trip and describe to a limited extent the Canadian approach to mining.

Jan 1, 2007

By A. V. Tarasov

The lack of technology for processing of sub-grade ore concentrates and intermediate products for extraction of Zn, Pb, Cu and precious metals at the metallurgical stage was a constraint for an increase in the production of these metals. The technology developed in the Gintsvetmet Institute is based on an improved electrothermal smelting process for treating calcined charge, ensuring thereby a reduction in power requirement and improving the environmental performance of the process. Electric smelting of sub-grade polymetallic concentrates produces lead bullion, to which the bulk of gold and silver reports, as well as well segregated matte and slag concentrating the bulk of zinc. Lead bullion and matte are commercial-grade products; zinc is recovered from high-grade (15% Zn) slag by slag fuming process. Reduced loss of precious metals in slag ensured by the given technology is attributed to the fact that the slag contacts with matte with low contents of gold, silver and lead, rather than with lead bullion. Limited amounts of off-gas typical of electrothermal processes ensure cost-effective operation of dust recovery devices and a reduction in emissions of harmful pollutants into the ambient air.

Jan 1, 2002

By M Bettison, R Wright, N Taylor

The primary mine planning focus during early study phases of future mining projects is Life of Asset ore production and grade quality, this will always be the situation. While waste schedule optimisation is generally considered in the latter study phases nearing execution for a limited number of schedule periods only and not a true optimisation considering all attributes such as waste destination location, design, cycle time and closure. This can be particularly applicable in large multi-pit bulk mining operations where one approach to meet Life of Asset ore tonnes and grade targets has been to maintain pit development flexibility resulting in large open pit areas and substantial expit Overburden Storage Area (OSA). The value opportunity is to develop a Life of Asset waste schedule source-to-destination optimisation prior to mine development considering all applicable attributes and routinely review throughout the Life of Asset taking account of improved ore and waste knowledge.CITATION:Taylor, N, Wright, R and Bettison, M, 2018. Utilising mine planning to deliver closure landforms through productive movement, in Proceedings Life-of-Mine 2018, pp 96–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Robert Hopler

After the disbanding of the Gunpowder Trust Association in 1904, the Association of Independent Powder and Dynamite Manufacturers was formed, followed in May of 1906 by the formation of the Association of Manufacturers of Powder and High Explosives. Due to a lack of success in attracting all manufacturers to membership, these organizations did not survive.

Jan 1, 2014

By R. Carrier

"There has been a continuous evolution with the use of pre-cast concrete elements in the construction of aluminum smelters. In 1990, Phase I of Alouette was built using cast-in-place concrete exclusively. Whereas, other AP 30 technology plants such as Hillside 2 in the mid-1990s used pre-cast concrete beams with cast-in-place floors. Mozal 2, in 2002, used pre-cast concrete beams with pre-cast partial-slab operating floors. Alouette Phase II went further. Not only were the potroom building beams and floors pre-cast, but the entire pot support system, insulating walls and basement jersey walls were pre-cast. Once the techniques for bending and welding the reinforcement bars and the design for attaching electrical insulating plates to the concrete was perfected, the challenge for the project remained only in the logistics of transporting the pieces to site and simple erection. The overall impact on the project was dramatic. Using prefabricated concrete not only allowed advancement of the schedule, but totally eliminated formwork, re-bar installation, and form removal activities along with the handling of all the materials involved with these activities. With the elimination of these labour and material-intensive portions of the job, exposure to work injuries was dramatically reduced. The most prevalent activity for lost time accidents is during the rough work associated with concrete formwork, placing concrete and form removal. Another area where prefabricated elements were successfully used on Alouette Phase II was for the insulating walls enclosing the pot area, known as the ""claustra walls"". Usually these walls are constructed in-situ using mortar and breeze block. Success was also achieved with prefabrication of the perimetric walls that are installed at the lower floor of the potroom. A big advantage of using prefabricated concrete in the electrolysis area is in assuring electrical isolation for the operating floors. Poured concrete requires a meticulous clean-up effort before commissioning to establish the electrically ""floating"" characteristics of the operating floors. Poured concrete results in ""wash"", stray wood,"

Jan 1, 2006

G. M. TAYLOR,* Colorado Springs, Co1o.-I do not think the plan outlined in this paper would work at Cripple Creek. Most of our men have had a pretty good education. The Cripple Creek district is a lessee district-I do not think there is one mine operating in Cripple Creek to-day that does not have the leasing system. We have as many men leasing on our property as we have mining and every plan who is working for wages is looking for n lease-everyman has mined for him- self, he has been his on7n boss on n lease, either on our own property or

Jan 1, 1919

By D. Belin

Treatment of dilute acid mine drainage and similarly polluted water is becoming increasingly complicated. The pressure of economics is now exacerbated by legislation which classifies as hazardous waste the precipitates from conventional lime treatment plants. Since acid mine drainage invariably contains sulfate ions, one solution is to use anaerobic Desulfovibrio type bacteria to reduce the sulfate into sulphide ions which could then be used to precipitate out the heavy metals. Results are presented for both batch flask cultures and continuous column tests. Compost was used as the bacterial substrate in the column test which simulated heaps. Conditions changed from aerobic to the required anaerobic deep in the columns. Polluted feeds (up to 700 mg/l zinc) gave effluent containing well below I mg/l zinc over extended periods. Direct transfer of sulphide ions through a stream from an isolated container of bacteria is a good alternative.

Jan 1, 1991

By Orlando C. Rojas

The Potrerillos Smelter commissioned a new El Teniente converter in 1985. As a result of the use of this technology, the Peirce-Smith converters have been processing only high grade matte or white metal. These operational changes resulted in damages to the converter shells, excessive splashing and cold dope generation and very short refractory campaigns. The paper shows the modifications to the tuyere angle, mouth design changes and new techniques for mouth cleaning and gas handling. Operational results up to 1991 are also shown.

Jan 1, 1993

In the late 1980s and into the 1990s, the Mountain Pass Mine in California produced about 40 percent of the world?s rare earth elements. At the height of this production, the facility produced up to 54 L/s (850 gpm) of saltwater that was piped to offshore holding ponds where the water was evaporated. In 1998, following a series of waste water pipeline breaches, separations activities were suspended, reducing the Mountain Pass site to just the openpit mine and mill. The environmental concerns were addressed and the affected areas have since been remediated. However, in the years following the breaches, 97 percent of the world?s production of rare earth elements moved to China. By 2011, Molycorp, and the Mountain Pass Mine, had rebounded from the difficult times and were once again in a position to become a significant player in the rare earth industry.

Jan 1, 2011

By Z. Zhongwei

The leaching kinetic of mechanically activated sphalerite with acid FeCl3 solution was investigated. The result has shown that mechanical pre-treatment has greatly enhanced the leaching process. Comparing with the original concentrate, the activated one can be leached more completely at relatively lower temperature with diluter FeCl3 concentration within a shorter leaching time. The activation energy for the activated concentrate is 27 KJ/mol, while for the original one is 52 KJ/mol.

Jan 1, 1995

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

By Fabio Mielli

Encompassing between 20 and 40 percent of the typical mining operational costs, energy in mining operations is a growing concern for the industry. However, this concern is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. Managing energy efficiency is becoming a keystone of successful companies. The suggested energy strategy in mining and mineral processing operations must follow a well-structured approach to include the following: ? Understanding where energy is being used and why. ? Recommending and implementing energy conservation measures. ? Driving visibility to targets and results. ? Leveraging the energy spent across the enterprise. ? Developing a robust energy and sustainability strategy. Additionally, it must ensure that all decisions support the financial and operational integrity of the business.

Jan 1, 2012

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014