Search Documents

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By Koji Matsubara, Yoshiaki Iguchi, Shoji Hayashi

Iron ore particles of a limonite iron ore were reduced completely with H2 at 1023K to 1273K in a fluidized bed. Then, at 973K, the formed iron was exposed to HrH2S mixtures (sulfur activity, as=0.5) for 3.6ks and carbidized with CO-H2-H2S· mixtures at 0.1 MPa. During the carbidization, the particles of about 150mg were sampled at every 600s interval. The sampled particles were analyzed by XRD and chemical analysis for C and S to evaluate the content of Fe3C, Fe5C2, Fe and free carbon. The reaction extent is defined as fo=Xfc3C +xFc5c2; x is the molar fraction of Fe in Fe3C. The carbidization curves can be fitted very well to -ln(l-f0)=g(pb T)t; g(p; T) is the carbidization rate, i.e. the carburization rate on the pore surface of reduced iron. The rate is found to be nearly proportional to the specific surface area of reduced iron, a P 0 , which decreases with increasing the reduction temperature. The value of a P 0 does not change by the carbidization and the stability of the iron carbide product in the atmosphere increases with the temperature.

Jan 1, 2000

By A K. Ghosh

"Inrush of water is always an issue, especially for mines located in heavy rainfall areas. Nowadays, mining companies and research institutes have developed many advanced technologies for study and analysis of hydrological processes. In this paper, an advanced method is introduced, which uses the Shuttle Radar Topography Mission Digital Elevation Model (SRTM DEM) data in the Geographical Information System (GIS) platform to simulate the stream distributions around two specific mines: Super Pit and Griffin coalmine in Western Australia. The impact of this approach is important because it reduces the time and economic cost by creating a high spatial resolution hydrological map in the specific areas. The study identifies the flow path of the run-off water, which helps in adopting a suitable water management plan surrounding the case study mines. The results match with the ground reality. Based on the results, the stream structure around Griffin coalmine is more complicated than that of Super Pit. The bifurcation ratio and drainage density are computed to estimate the subsoil permeability characteristics of the two mines. Recommendations have been put forward to prevent and reduce the potential risks of water accumulation around the open pit mines.Citation:Ghosh, A K, 2016. Application of Shuttle Radar Topography Mission Data in Hydrological Analyses of Super Pit and Griffin Coal Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 162–169 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

By Katsukiyo Marukawa, Manabu Iguchi, Sigeta Hara, Shinichiro Yokoya, Sigeo Takagi

"A numerical analysis and water model study of the mold region of a continuous casting apparatus was performed with a novel injection concept using swirling flow in the pouring tube, to control the heat and mass transfer in the continuous casting mold.As a result, the following results were found:1) By changing swirl strength, it is easy to control the flow pattern as well as the direction of the flow.2) Uniform velocity distribution can be obtained within a very short distance from the outlet of the nozzle.3) Heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl.4) Swirl helps the superheat in the melt dissipate.S) Penetration depth of nozzle outlet flow is decreased remarkably by the application of swirling.6) For the case without swirl, the peak of the flow moves near the mold-wall with flowing down from the outlet of the nozzle due to the Coanda-effect. On the other hand, peak of the flow moves near the mold axis with flowing down from the nozzle-outlet within considerable short distance, namely axi-symmetric velocity distribution can be obtained within very short distance from the nozzle-outlet.Those findings mentioned above are very useful to control the flow pattern in the billet and bloom continuous casters."

Jan 1, 2001

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

By D. Pacey

"This paper reviews the installation, start-up, and operation of a comprehensive monitoring and targeting management technique in which all plant utilities (i.e., electricity, natural gas, compressed air, and water) are managed as controllable resources in the same way that raw materials, mined ore, personnel and capital are managed.The essential elements of monitoring and targeting (M&T) include:•gathering in a systematic, disciplined way the utility information by energy account centres;•closely monitoring the utilities used in each centre and comparing them with production on a common time base (e.g., kWh/ton per day);•bench marking and target setting to pro-vide attainable energy reduction goals which can be further refined as they are achieved; and•establishing an implementation plant that may provide efficiency enhancing benefits to various operating areas within the plant.The M&T system will reduce utility consumption per unit of production on a continuing basis.This would translate into sustained operating cost and waste. M&T will also provide better information for assessing the plant operation and progressively implementing further enhancements."

Jan 1, 1997

By C. G. Treworgy

Geologists at the Illinois State Geological Survey are evaluating geologic and land use conditions that affect the minability of coal to determine how much coal is available for development using current technology and mining practices. Coal resources are being evaluated for selected 7.5-minute quadrangle study areas. In a central Illinois study area, more than 25% of the deep-minable resources were limited from development by unstable roof conditions resulting from thick unconsolidated sediments overlying thin bedrock overburden. In some southern and southeastern Illinois study areas, geologic conditions associated with a paleo-channel limit the minability of significant resources of low-to medium-sulfur coal. Some features which were thought to limit mining, such as areas of closely-spaced oil wells, have been found to have minimal impact on the amount of coal recovered.

Jan 1, 1995

By Norman A. Grant

"Location and Transportation FacilitiesTHE BEAVERLODGE area of North Saskatchewan is on the north side of lake Athabasca, 500 air miles northeast of Edmonton.The main Eldorado operation and townsite are on the north •side of Beaverlodge lake, which is immediately north of lake Athabasca and is separated from it by only a mile long portage at Lodge bay. The once famous town of Goldfields. Saskatchewan, and the Box property of the Consolidated Mining and Smelting Company of Canada, Limited, are located on lake Athabasca nine mines from Beaverlodge townsite.Previously, all Eldorado freight was delivered by barge at the Lodge Bay portage, hauled across the portage, and across Beaverlodge lake by small Northern Transportation Company barges, which involved many handlings.In 1952 the port of 'Bushell' was established at Black bay. This is a particularly snug harbour, well protected from the main body of the lake and with good foundations for docking facilities. A Butler building, 300 ft. by 60 ft., and tank farms provide storage at the port. A •road from Bushell to the main Beaverlodge operation, a distance of twelve miles through rugged terrain, was built by the Saskatchewan Government. The cost was shared by the Saskatchewan Government, the Federal Government, and Eldorado and other mining companies.Along this road are located the properties of several enterprising mining companies and near the midpoint lies the ambitious budding town of Uranium. This road has made portaging unnecessary and palletized freight loaded at Waterways, Alta., is now loaded directly on trucks at Bushell and delivered to the point of consumption."

Jan 1, 1953

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By Danfeng Xu

The majority of the world?s nickel (Ni) resources occur as laterite ores, which are exceptionally complex, lower grade (<1.5% Ni) and expensive to treat using conventional smelting and high temperature/pressure autoclave methods. Heap leaching is a promising, less costly, alternative technology for processing low grade nickel laterite ores. However, significant technical challenges remain with Nickel laterite heap leaching, preventing its general adoption. This paper presents some highlights of laboratory column leaching studies undertaken to characterise, evaluate and optimise sulphuric acid leaching behaviour of Nickel laterite agglomerates. They provide basic but valuable information regarding Nickel laterite agglomerate structure stability and leaching performance under industrially-relevant, continuous acid irrigation conditions. In particular, Nickel and other key metals? (e.g. Co, Fe, Al and Mn) extraction rates, free acid concentration, bed slump and structural changes were determined at a given acid percolation rate as a function of time. Potential implications of the findings, for devising strategies for improved Nickel laterite plant heap leach operations are discussed. Keywords: nickel laterite, column leaching, agglomerates, leaching kinetics, acid consumption

Sep 1, 2012

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy&apos;s Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation&apos;s coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966

By Bern Klein, Givemore Sakuhuni, Libin Tong

The use of continuous discharge centrifugal concentrators introduced in the early 1990’s for recovery of gold associated with sulphides has introduced a novel application niche for gravity concentration which could not be realized with the low mass yield batch and semi-continuous concentrators. A typical application is scavenging gold associated with sulphides from flotation tails which has potential to increase productivity by reducing gold loss to tailings and lower grinding cost by using a coarser grind. However, the full potential of this technology has not been fully exploited partly due to the lack of reliable small sample procedures to demonstrate applicability. This paper introduces a bench-scale procedure developed to characterize the Knelson Continuous Variable Discharge concentrator (CVD) for scavenging gold from flotation tails. The procedure code named gravity release analysis was derived from standard flotation release analysis. It is a modification of the gravity recoverable gold and gravity amenability test in order to best simulate continuous centrifugal concentration. Based on this iterative procedure, a gravity release index similar to the flotation rate constant, for measuring individual mineral gravity susceptibility for an ore is introduced which can be a useful quantitative measure to both predict application of centrifugal concentration and for plant design. The gravity release analysis procedure was tested on a polymetallic flotation plant tailing at Myra Falls, BC, Canada and results show that it can predict CVD performance. The gravity release index for gold was observed to decrease with each successive cleaner stage showing that the initial stages recover liberated gold whilst successive runs recover gold associated with sulphides and or gangue. The difference in magnitude of the gravity release index for different mineral species shows the species separable by centrifugal concentration.

Jan 1, 2014

By R Zhang, X Huang, M Zhou, X Lv, C Bai

Iron ore sinter accounts for a large proportion of blast furnace ferrous burden in Chinese steel mills. Depleting high-grade iron ore resources and spreading complexity of iron ores in mineralogy and morphology have made it more difficult to utilise iron ores efficiently and economically. In this paper, the physical properties of iron ore particles were characterised using mechanical sieving, laser sizing and gas adsorption. From those measurements, two physical indices (fractal dimension of the particle size distribution and surface morphological factor) are defined as important variables for optimising the granulation performance of iron ores. The moisture capacity and the contact angle of iron ore particles with water were also measured to determine the strategy of water-feed in the granulation process. It can be concluded from the experimental results that an increase in the fractal dimension of the iron ore particles will lead to a better granulation performance, while an increase in moisture capacity with a range of 12.8 ~ 14.8 per cent would increase the optimum water content where the granule packed bed achieves its best permeability. Furthermore, the optimum permeability varies inversely with the moisture capacity of the sinter mixture.CITATION:Huang, X, Lv, X, Zhang, R, Bai, C and Zhou, M, 2013. Iron ore characteristics and their application in optimising the granulation process, in Proceedings Iron Ore 2013 , pp 261-268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By Henry J. Kellner, Michael J. Brnich

This U.S. Bureau of Mines report addresses issues involved in using a limited number of training apparatus to give hands-on self-contained self-rescuer (SCSR) training to a succession of miners, and provides guidance regarding methods for minimizing the spread of infectious diseases. Procedures used for preventing the spread of infectious organisms in dentistry, cardiopulmonary resuscitation (CPR) training, and scuba training are examined. The sanitizing methods of three organizations that require individuals to insert the mouthpiece as part of the SCSR donning sequence are discussed. It was found that each of these organizations was able to render their mouthpiece assemblies microbe free simply and inexpensively.

Jan 1, 1989

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full&apos; understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949