Search Documents

The Callie Underground Gold Mine (Callie) is owned by Newmont Asia Pacific and located 531 km north-west of Alice Springs in the Northern Territory. Historically, stopes have been mined utilising a primary and secondary stoping sequence with cemented aggregate fill and rock fill respectively. Current and near-future mining will employ long hole open stoping with rib pillars and rock fill with a paste fill system approved to allow a higher extraction ratio from mid-2011. The Callie rock mass is of good quality with little or no mining difficulties during development and stoping to a depth of 1140 m below surface. Development is currently occurring at depth of 1360 m below surface. Stress damage previously observed only in secondary stope accesses is now observed in development unaffected by stoping stresses. A change in rock mass properties is being experienced with depth, with more pronounced and frequent joint planes. Also, other structures are intersected more commonly, such as lithological boundaries and fault zones. The 'Callie rock factory' mentality that has persisted for years is challenged. This paper covers an appraisal of the stress and ground condition changes at Callie. The appraisal outlines the mine design criterion that was developed and examines the transition from a low stress environment to one where stress damage is observed. Discussion includes a judgement on the rock mass damage observed in development, the dominant geotechnical factors influencing the change in ground conditions, and if a correlation can be made between the observed rock mass damage with stress through the use of numerical modelling.

Nov 25, 2010

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By Kumar Ashish, Shukla Akhilesh, Kr. Rokkam Kiran, M. Sheeba, S. Sombhatla Sundar

"Purification of zinc leachate plays a predominate role in zinc leaching refineries, to produce impurity free cathode sheets. As a part of such purification sequences, copper cementation with zinc dust is the preliminary step, since the presence of copper will preferentially deposit during zinc electro deposition and has the effect of reducing current efficiency. The cake thus produced is being accumulated as an inventory, due to invariable market and leading to space constraints & hazardous ambience. Hence, a project has been taken up for in-house generation of copper sulphate solution through ammonical leach followed by solvent extraction process and utilizing it as an active promoter for zinc sulphide flotation in Hindustan Zinc’s own captive mines. Cold purification cake majorly contains copper (30-40%) along with zinc (10-20%) and cadmium (2%). Confirmation to the above statement, photomicrographs of purification cake also confirmed the major presence of copper in metallic or oxidized form. In present work ammoniacal carbonate leaching of purification cake followed by solvent extraction using diketone based solvent has been studied under the influence of various parameters viz., temperature, agitation, pulp density, ammonia, CO2 dosages, solvent concentration, and impact of w/s zinc on leaching and solvent extraction. Leaching kinetics determined based on shrinking core model. Chemical reaction at unreacted core was found to be the rate controlling step. The estimated activation energy was found to be 24 KJ/mol. Leached copper has been extracted by solvent extraction with a ß diketone based solvent and is stripped with sulfuric acid as concentrated copper sulfate solution. The above established R&D findings are successfully implemented in the Commercial plant with a treatment capacity of two tons of cold purification cake per batch. Till now 500 MT of Purification cake has been treated, and generated 6500 MT of copper sulphate (55 g/l Cu), with final Cu recoveries between 87-90%."

Jan 1, 2018

By M. L. Cunha

The lack of control of As and Sb compounds from copper smelters and converters has rendered some chalcopyrite containing arsenopyrite, stibnite and tetrahedrite minerals unusable for metal extraction. In the present investigation, we have studied the carbothennic reduction of Portuguese chalcopyrite mineral concentrate in the presence of lime/CaS04 and CaS04/Si02. Thermodynamic equilibrium calculations were performed to study the distribution of As and Sb between metal and the CaO-Si02-FeO slag phase. The phase equilibrium calculations also show the effect of oxygen partial pressure on the increase in the volume of the slag phase, which helps in lowering the copper metal formation temperature and facilitates a better separation between metal, matte and slag. The reduction reaction kinetics was studied between 850°C and 1100 °C, and the phases formed were identified by X-ray powder diffraction and scanning electron microscopy techniques. The importance of this research for using recycled matte, lean and rich minerals with As and Sb is also explained.

Jan 1, 2001

By A J. Burchell

The introduction reviews the tunnelling carried out in Singapore since the early 1980s. Between 1983 and 1990, Phases 1 and 2 of the mass rapid transit system were constructed. These included some 20 km of bored and cut and cover tunnels together with 18 underground stations. Some particular points of interest in this massive project are briefly commented upon. Reference is also made to other underground or underwater schemes undertaken during this period such as the proposed large caverns project and the submerged tunnel to Pulau Seraya. A description of the subsurface works, now under construction in Singapore, follows. This includes an all underground North-East railway line 20 km long with 16 stations. At a budget of US$ 3 billion, this is a major civil engineering undertaking. Another project is the extension of the railway to Changi Airport which involves 3.5 km of twin tube tunnelling together with a major underground station which is fully integrated into the airport terminals. An on-going program of further major railway extensions over the next 10 to 15 years is in place and an outline is given of some of the most important underground sectors. Other proposed projects such as the underground roads system and the deep level sewers are briefly described. Together they demonstrate the very significant volume of underground construction scheduled for the next century in Singapore.

Jan 1, 1999

By Harry Jomini

Introduction The Wakefield plant of the Aluminum Company of Canada, Limited - a member of the Aluminum, Limited, group of companies - produces magnesia, magnesia fertilizer ingredient, and hydrated lime, from brucitic limestone. Wakefield is on the Gatineau river in Wakefield township, Quebec, some 22 miles north of Ottawa. The plant is near the western bank of the river adjacent to the Ottawa-Maniwaki highway and branch line of the Canadian Pacific railway. The plant is unique in the sense that it is the only place in Canada where brucite is processed. It is also distinguished for its outstanding safety record, as not a single lost-time accident occurred during either 1948 or 1949. The plant is amply provided with safety and comfort provisions in keeping with the standard practice in all of the twelve plants operated in Canada by Alcan and its associated companies. History Following the identification of brucite in the Rutherglen and Bryson districts in Ontario, occurrences of the mineral were discovered in the Wakefield area, Quebec, in 1939. After exploratory work on these deposits and investigation by the Bureau of Mines, Ottawa, on a method of extracting the brucite from the ore, a plant for treating the ore from the Maxwell property was built in 1941 by the Aluminum Company of Canada and commenced operations in early 1942. The process used is more or less in accordance with the method worked out by Mr. M. F. Goudge of the Bureau of Mines.

Jan 1, 1950

By B. Burke

Magnesium and its alloys are attractive materials for use in automotive and aerospace applications because of the low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present paper reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents preliminary results of current work on producing magnesium alloys via powder metallurgy P/M. P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The feasibility of producing magnesium powder metallurgy products utilizing the industrially dominant process of mixed powder blending, uniaxial die compaction and controlled atmosphere sintering was investigated. An alloy composition based on the commercial Mg alloy AZ31 (3% Al, 1% Zn) was used to facilitate comparison to similar wrought products. The optimal processing conditions (compaction pressure, sintering time and temperature, and quenching temperature) were found to maximize sintered density and mechanical properties.

Jan 1, 2007

By S D. Dessureault

The largest surface coal mine in North America requires complex materials handling infrastructure to fulfil the highly variable quality specifications of its contracts. These diverse demands, reflected in the arrival of numerous customer trains every day, necessitate the integration of information in every stage of production. To meet this goal, quality measurement, train line-up and mine planning processes are being integrated into local and remote control rooms. The effectiveness of such a system can only be measured by comparing decisions that are made with, and without, each of the individual integrated control systems. Traditionally, mine controllers use their experience, intuition or a variety of trial-and-error spreadsheets to determine the ideal materials handling flows needed to achieve the correct quality. These balanced decisions are complex since many factors must be considered such as the mine plan, fleet costs, quality variability and others; consequently mine controllers usually have widely varying success between crews.An evaluation model was developed to assess the impact of a decision support system (DSS) integrated in a control room for controlling the coal blending process. To this end, an ARENA-based simulator representing the whole production process can be used to pull performance and current materials handling settings directly either from the real-time systems in the mine, or from historical data. In this way, the same shift (breakdowns, cycle rates, etc) can be simulated and performance compared. Different settings of the DSS, in terms of what information is displayed and the methods for doing so, can be tested for effectiveness. The historical data are extracted directly from a corporate data warehouse, without altering the everyday working databases. At the same time, the simulator writes its results back into the same data warehouse structure, allowing the same KPI reports to be used to measure simulated shifts.

Sep 26, 2011

By W. E. Uren

The Dominion Coal Board was created by Statute passed on July 17th, 1947, and was brought into effect by proclamation on October 21st, 1947. It is, consequently, a comparatively young body, having been in existence for only eighteen months. Before dealing with the constitution and duties of the Board, it may be well to answer the unspoken question of why it has been considered necessary to single out coal as one specific mineral requiring the continuous attention of a specially created permanent Board. In Canada, coal has been the neglected sister of the more spectacular minerals and it comes as a surprise co many to note that in 1948 the value of the coal produced in Canada was higher than that of any other mineral with the one exception of gold. Coal touches upon our daily lives in many different places of which the public are not generally conscious. As household fuel, it is a necessity of life in this northern climate; as a source of steam, it provides the heat for most of our industries; it is the food of the 'iron horse' chat shuttles our persons and our goods across the land; it is the source of power in many parts of the country; it is the chemical reducing agent chat, in our furnaces, transmutes the metallic oxides to the virgin metal. Coal is, in fact, the indispensable mineral chat forms the corner-stone of our present structure of industrial civilization. Is it, then, such an odd thing that the provision of an adequate supply of coal should be a matter of national interest or that measures should have been taken by government co provide for a constant watch, by a permanent Board, on the supply of co al? ? The Board is the result of the recommendations of the Royal Commission on coal which made a long and detailed study of the Canadian coal problem. It is composed of a permanent Chairman and six part-time members, most of whom have had intimate contact with various phases of the industry.

Jan 1, 1949

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By A Agasty, O Langefeld, MáKellner, E Clausen

The lowering of the pollutant concentration limits at the workplace subjects the mining industry to higher requirements for dilution; this situation is worsened with the current discussions within the European Union (EU) to set new stricter exposure limits for nitrogen oxides in the workplace. This is directly reflected in the performance of the mine ventilation system, which may need to be revised to meet the new standards. The after blast re-entry time, being inversely proportional to the threshold limits, will be higher for a lower limit. This in turn increases the down time for production from the blasted area.Numerical tools have been very useful in predicting the effectiveness of ventilation. This study aims at analysing the dilution time for NOx gases from an ANFO blast in a room and pillar panel. The effect of changing the ventilation on the dilution time is studied next, which helps with the selection of a suitable ventilation system.CITATION:Agasty, A, Clausen, E, Kellner, M and Langefeld, O, 2013. After blast re-entry time for a room and pillar operation, in Proceedings The Australian Mine Ventilation Conference , pp 179-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A. A. Brant

"Improving geological and geophysical evaluation should serve to reduce the early-stage risk assessment and there-by contribute to exploration expenditure stimulation. The limitations of present-day methods are reviewed, particularly as to anomaly causes, depth penetration and quantitative physical interpretative abilities. Some of the problems now under study are discussed. Future developments expected include the treatment of quantitized geologic and geophysical data, as well as continuing attempts toward computerized interpretation."

Jan 1, 1967

By Q. Xu

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactant was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1991

By H. N. Frock

The use of low-angle forward light scattering for measurement of particle size distribution has been described previously.1 Laboratory instrumentation using this technology is used routinely in operating plants for quality control and production control.2,3 Extension of the technique to on-line process monitoring and control has also been undertaken in several important areas. This paper will discuss the application of MICROTRAC R systems to the monitoring of particle size in wet slurry processes and dry powder grinding circuits. Examples of existing installations will be given with emphasis on performance and on-line reliability.

Jan 1, 1979

This paper presents the results of research aimed at proposing new solutions in the area of belt conveyor elements. Many factors, such as energy consumption costs, and operating costs of belt conveyor elements, including belts, idlers and drives have an impact on the operational costs of conveyors. The paper presents special tests of new materials for the bottom cover of an energy-saving belt conveyor, which decrease rolling resistance. It also presents large-scale in-situ tests of a high-output belt conveyor for the purpose of simultaneous measurements of various types of conveyor belts (standard vs several energysaving types) under typical operating conditions of a lignite surface mine. Improvements in materials used for the bottom belt covers, supported by specially developed comprehensive tests of the new types of belts have provided valuable results of various proposed solutions. Since the tests of belts were done at exactly the same time and in the same operating conditions, direct comparison of the results is valid and should lead to a substantial decrease in the conveyors? drives? energy consumption, which will improve the effectiveness of belt transport and minimize its negative influence on the environment.

Aug 1, 2013

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By Anthony Harding

In a world of technology and electronic communication, it is easy to forget what engineers do best with a problem: sitting around a table, exchanging views and ideas with sketches and respecting everyone?s view. This was the approach adopted in the project to arrive at a solution for the cross passage opening sup-port for the Seattle University Link Extension. Schedule and space constraints usually impede concurrent cross passage excavation and tunnel boring machine (TBM) operation. And where the space is constrained, opening support solutions that maximize available cross sections are of great benefit. While there are a number of solutions that minimize space, some of these solutions can require expensive steelwork and extensive drilling and fixing. However, following a detailed round-the-table discussion of the options and constraints, it was identified that a shotcrete shell would not only limit obstruction of the space during installation, but also permit easy installation, particularly around services, and avoid costly steelwork and drilling and fixing.

By J. E. Garlanger

Each year, Florida mines approximately 40 million tons of phosphorite, most of which is ultimately converted to various commercial fertilizers. The phosphorite is mined from within the bottom portion of the 40-to 60-ft. thick surficial aquifer, using open pit mining techniques. The ore zone or "matrix" is generally overlain by relatively permeable fine sand to silty and slightly clayey fine sand. The ore itself is highly variable in nature but, in Central Florida, typically consists of less permeable clayey phosphatic sands and sandy clays with stringers of permeable sand. The ore is much more sandy in the north Florida mining area.

Jan 1, 1990

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012