Search Documents

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By R. W. Mei, R. A. Strombom, D. J. Moore

"Heat-shrinkable cable accessories are solving problems in the mining industry. This paper describes a range of products used by the industry, including low-voltage splices, high-voltage splices to 8.7 k V, cable repair sleeves, mining cable terminations used on system voltages up to 25 kV and motor connection kits up to 8 k V. Technical procedures and designs are illustrated.IntroductionThe development of high-performance heat-shrinkable materials slightly over 20 years ago proved to be one of the major technological breakthroughs in power cable accessories. Heat-shrinkable products were introduced initially for use as low-volt age cable accessories in the aircraft and electronics industry. A program of continuous development and product introduction now enables the manufacturer to offer a broad range of products for mining, industrial and utility electrical systems.With the advent of atomic energy, an important discovery was made-exposure of some plastic materials to high-energy electrons can cause the permanent crosslinking, or intermolecular joining, of adjacent molecules. Once the material has been crosslinked, it will not melt or flow at any temperature.The unique properties of heat-shrinkable products also result from the exposure of special thermoplastic formulations to high-energy electrons. Because of crosslinking, these products have perfect elastic memory. The heat-shrinkable products are supplied in expanded condition. When heated, they will shrink and tightly cover the object over which they have been placed. 'The functional and operating demands of mine cable accessories exceeded the classic electronic applications of heat shrinkable materials. These demands required a very sophisticated program to develop materials and adhesive systems that could endure the operational environment associated with the mining industry,Ease of assembly, low installed cost and operational reliability are among the main reasons for the acceptance of heat-shrinkable mine cable accessories in electrically powered mines. For over a decade, these systems have been demonstrating proven performance."

Jan 1, 1980

By John F. Papp

Based on a review of historical domestic and international chromium metal production capacity, production, consumption, trade, and trade literature, world annual chromium metal production capacity in 1995 was estimated to have been 38,300 metric tons, a drop from 43,500 tons in 1994. World chromium metal production and consumption were estimated, on average from 1984 through 1992, to have been 21,000 tons per year. U.S. consumption was estimated, on average over the same time period, to have been 6,200 tons per year. The major world chromium metal producers between 1984 and 1995 were China, France, Germany, Japan, Russia, United Kingdom, and United States. From 1984 through 1992, world trade averaged 8,400 tons per year. Germany and the United States accounted for over 75 percent of imports on average during the same time period. U.S. chromium metal import value rose from under $1 per kg before 1964 to over $6 per kg in 1993. Over the same time period, prices rose from about $4 per kg to about $10 per kg. Chemical specifications have become more stringent. Detailed chromium metal trade, prices, value, chromium metal chemical specification, and production capacity by country are reported. A shift in trade patterns was anticipated as Japan exits production and displaces Germany as the second largest importer and as Russia increases its role in world trade.

Jan 1, 1995

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

By J Graaf, R A. Murrell

Gold Fields Australia is constructing two major ventilation shafts at the Wallaby gold mine in Western Australia. The new ventilation shafts are required to facilitate the long term ventilation strategy for the mine, thereby allowing continued extraction of ore beyond 1000 m below the surface. The construction work has involved all of the challenges that shaft construction can throw up, including challenging geotechnical conditions, unexpected high water inflows and major circulation loss during pilot hole drilling for raise boring. An extensive geotechnical and hydrological investigation program was undertaken prior to awarding the shaft construction contracts. While most of the risks were identified, several proved to be much more challenging than expected. The shaft construction methods included conventional sinking into the fresh rock profile in each shaft, followed by raise bore pilot hole drilling and reaming. A headframe was constructed for the first shaft, which was sunk to 92 m with a stage suspended in the shaft to facilitate the concrete lining and provide rope guides for the kibble winding. Drawing from experience when sinking the first shaft, additional ground pre-conditioning was implemented for the second shaft, which was pre-supported with continuous piles to 28 m followed by sinking to 50 m using a crane instead of winders and a headframe. Following the conventional sinking through the weathered zone in each shaft, the shafts were completed using a raise bore. The first shaft utilised a riser pipe and rotary vertical drilling system (RVDS) with the second shaft having utilised a dual rotary rig for pilot hole drilling. This paper reviews the site investigations undertaken, construction methodologies applied, the results achieved and the lessons learnt.CITATION:Murrell, R A and Graaf, J, 2017. Shaft construction at the Gold Fields Wallaby mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 321–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

A genesis based on new developments in the physical chemistry and flow properties of colloidal substances is proposed for the pipe-like Peko orebody. The rheological behaviour of sediments is governed by the contained colloids. Remobilization of thick pasty sediment during diagenesis is regarded as an essential step in the concentration of metal dispersed in sediments. At a high concentration the sediment pore fluid is a dense gelloid such that van der Waals attractive forces between the colloidal particles exceeds the coulombic repulsion. This permits accretion of the colloids into globular clots and their fracture fragments. These have a uniform size distribution dependent upon the rate of shear, and the sediment lithifies to clotted, porphyry-like, "gritty", dolomitic or igneous-looking intrusions and flows. The physical chemical properties of natural sediment colloids appear adequate to account for ore formation.Adsorption accounts for the dispersion and retention of metal in sediments. Accretion accounts for the segregation of the colloidal materials to give the various types of clotted igneous-looking intrusive source rocks. Syneresis enables the colloids to spontaneously draw together and to dehydrate. Formation of an ordered lattice achieves a lower energy state and desorbs metals and insoluble metal compounds "particle by particle" into the escaping water of hydration and pore water. Peptization enables migration of the metal hydrosols as stable dispersions until they merge for outflow through seepage zones or water extrusion channels. Nucleation and concretion precipitate the metal dispersoids from pore waters seeping through hydrous parts of the source rock, porous beds, faults, and zones of weakness by which the connate waters leave the lithifying sediments. Gelatinous precipitated mineral matter in the ore channels is capable of thixotropic reliquefaction when disturbed by shock or movement. Local reintrusion, flowage, interveinings,brecciation, and intermixing of the materials is the result.The principles of the suggested genesis are applicable to both syngenetic and epigenetic mineral accumulations.

Jan 1, 1966

A stronger U.S. economy stimulated the domestic mineral sector in 1994. Metals demand was spurred by robust U.S. motor vehicle sales, while demand for major industrial minerals rose in response to highway and building construction. Domestic mineral and material demand is expected to increase in 1995, particularly if interest rates do not restrain the building industry and international monetary exchange rates remain advantageous to U.S. automobile manufacturers. Additional information on events, trends, and issues in the mineral and material sector is presented below and in the commodity sections that follow. Overall Performance Processed materials of mineral origin produced in the United States during 1994 increased to an estimated value of $360 billion. Domestic output of raw nonfuel minerals in 1994 was estimated at $34 billion, about 6% more than that of 1993. The value of U.S. minerals production has increased in 29 of the last 34 years.

Jan 1, 1995

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By D. M. S. Bhatia

Twenty-six insitu analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an increase in the concentrations of Ag, Ga, Ge, and In with As showing the opposite trend Bi, Cd and Sn did not show any pattern. Sb was not detected. These variation patterns nay serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1984

By Richard F. Link

The objective of this report is to explain a statistical method for the summarization, organization, and classification of multivariate assay and other data from the mineral industry. Multivariate data are those characterized by several measurements at each data point, such as assay data from a mixed metal mine, or blast furnace data. A specific method of linear discriminant analysis, the Mahalanobis d2 procedure, is explained, starting from elementary principles; the d2 procedure enables many measurements at many data points to be studied by investigating the interrelationships among the data. The relation of linear discriminant analysis to other statistical methods for treating multivariate data, in particular the eigenvalue technique of factor analysis, is also explained. Example analyses are made on data from the Frisco mine, San Francisco del Oro, Chihuahua, Mexico. The data comprise assay values for silver, lead, copper, and zinc taken at some 19,000 sample points distributed into 91 groups.

Jan 1, 1967

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By Robert W. Geehan

The Bureau of Mines has been developing deposits of critical and essential minerals in the United States since 1939. A preliminary examination of the Union lead mine was made in November 1944 and January 1945 by W. T. Benson, a Bureau of Mines engineer, who recommended development by diamond drilling. The Bureau conducted a drilling project at the mine from February 12 to May 16, 1947. The property is in sec.12, T. 17'N., R. 19 E., Mount Diablo Base and Meridian, in. southern Washoe County, Nev., about 15 miles south of Reno. The Union lead mane, also known 4s the Commonwealth mine, has been an intermittent producer of zinc-lead-silver ore since 1860. During World War II, ore was shipped to smelter& near: salt Lake City, Utah. The Bureau drilled 21 diamond-drill holes having a total length of 1,549 feet and 20 long percussion-drill holes with a total length of 359 feet. The program was designed to test for horizontal and vertical extensions of the ore body and to prospect for parallel ore bodies. As a result of this program, extensions of the ore zone were established, but no parallel ore-bearing structures were found. The areas drilled were limited by drill sites available.

Jan 1, 1950