Search Documents

By Felix Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36' W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Teguci-galpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced.

Jan 1, 1940

By D. Harrington

At the time of mine accidents one frequently hears the expression "there will be accidents as long as there are mines", or it may be varied to state that the accident in question was unavoidable, or something similar indicating inability to prevent accidents. However, it is the opinion of the writer, after over twenty-one years experience in both coal and metal mining, seven years being spent wholly in safety work, that by far the greater number of all accidents is due to carelessness or negligence. This carelessness or negligence may be on part of the victim of the accident or of one of his companions, or on part of his employer or possibly even of the inspector or safety man, and in some cases all of these agencies are involved. It manifests itself in various guises, one of the most serious being violation of state mining laws or regulations or of mine rules, and frequently the rules of ordinary common-sense. The cause very frequently is that trait in human nature to "take a chance" and it has been the writer's observation that the worst offender is the old-time miner who has come safely through many years experience, who was mining when the "safety man was a baby", and who clings to old-time ideas and practices and has "no use" for "newfangled" present-day "notions". Unquestionably, there are accidents, wholly unavoidable and many are caused by ignorance and by the new-comer in mining, yet as previously indicated, the writer's observation is that the old-timer is by far the worst offender, bringing grief to himself, companions and employer. Of the numerous manifestations of carelessness and negligence in connection with mine accidents, which have come to the notice of the writer, only one will be treated in this paper, viz: Violation of State Mining Law, and mention will be made only of explosions and major accidents in coal' mines with which the writer came in personal contact as investigator. In most cases, in addition to mine inspection after the accident, the writer heard the evidence given at Coroner's inquest and thus was enabled to for¬mulate fairly definite impressions as to events and conditions leading up to the occurrence.

Jan 1, 1922

By Joseph Jensen, J. B. Stevens

The history of the normal oil field is supposed to show an oil graph starting high in flush production, descending more or less steeply into the curve of settled production and dropping gradually to the vanishing point of economical operation. Together with this, somewhere in the early history of the field, there appears from a vanishing point a graph showing the production of water. During the period of settled production this graph rises higher and, toward the close, unless extensive work is done in the line of correction, rises far above the oil graph to the point at which the cost of operation terminates profitable pumping. Fields that start out with a high relative content of water are generally very short-lived. Fields that never develop a water problem are exceedingly rare. The McKittrick oil field, Kern County, California, with 840 acres of proved ground, 300 wells and a present recovery per acre of 94,598 bbl. from 1898 to Aug. 1, 1930, presents a study which is an apparent reversal of the outlined normal history. Though the history of the field now covers over 30 years of operation, it is still too early and the conditions too unique to project the graph of production to completion. The present conditions and directions of change are most interesting, in that the curve of oil production is remarkably flat and the curve of water invasion, after reaching an appalling height, has shown a definite reversal and a continued decline for 10 years. Early drilling in the McKittrick field was in or prior to 1898. Development continued steadily to 1918 when the present limitations of the field were determined. Shut-offs, according to accepted practice of the time, were made by driving the shoe into a shale stratum or into a tamped-in bridge of sand, rosin and clay. Records of early days speak of three waters: (1) surface water which was fresh; (2) an intermediate sulfur water, encountered below the top oil or tar sand; (3) bottom salt water. In different portions of the field any one of these waters let into a well by faulty completion might require immediate correction to obtain satisfactory production. In many wells,

Jan 1, 1931

By James A. Barr

When phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. TO attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per ccnt. of available phosphate, which, howrever, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney formation, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss. One of the largest temporary losses in the industry occurs in the Florida pebble district where the recovery of phosphate runs about 25 per cent. The loss is classed as temporary because most of the tailing has been collected in ponds and piles, where it may be reclaimed in the future should developments or improved processes warrant. In cleaning the Florida pebble phosphate, aside from the elutriatisn

Jan 1, 1916

By Bradford C. Wesstrom, Omar Araujo

"Impurities from an electrolytic refinery are typically extracted from the electrolyte utilizing conventional electrowinning cells. These cells are arranged in series with cascading solution flow and are commonly referred to as liberator cells. The Freeport McMoRan Copper & Gold El Paso Refinery has optimized the removal of arsenic in cascading liberator cells by utilizing two separate feed solutions. The primary feed solution is recycled liberator electrolyte and the secondary feed solution is ""neat"" tank house electrolyte. The secondary feed solution is added based on the voltage response across the individual cells utilizing independent variable frequency drive (VFD) pumps. When the voltage across a cell changes, a signal is sent to the VFD pump to maintain a cell voltage of 1.98 volts. By maintaining this voltage the copper content in each cell exits at 2-4 grams per liter. This safely optimizes the arsenic removal as copper arsenides on the liberator cathodes.IntroductionDuring the electrolytic refining of copper, impurities from the copper anode report both to the bottom of the electrolytic refining cell as slimes and to the electrolyte. The impurities which enter the electrolyte are arsenic, antimony, bismuth and nickel. The impurities that report to the electrolyte during the electrolysis process gradually increase. As these impurities increase, they are incorporated into the refined copper cathode. There are many processes that have been used to remove these impurities from refinery electrolytes. Some of them are listed as follows: solvent extraction, ion exchange, hydrogen sulfide reduction, bioreactor, adsorption onto a low - solubility metal-oxide hydrate, adsorption onto activated carbon and EMEW cells. The conventional process used by the copper refining industry for controlling the level of impurities in electrolyte involves multistage electrolytic cascading liberator cells. In these cascading liberator cells copper, arsenic, antimony and bismuth are removed as various mixed deposits from the electrolyte. Removal of these impurities is achieved through an increase in voltage resulting from the depletion of copper in the electrolyte through electrowinning. With this higher voltage, the Group Vb elements, arsenic, antimony and bismuth are deposited on the copper cathode and report as slimes to the bottom of the cells. Nickel is removed in a subsequent process."

Jan 1, 2012

Reliable sampling practices are the key to optimising the market value of a mining or chemical companyÆs stock. As a result, reliable sampling standards are needed. However, current standards on sampling present the æuniversalÆ Pierre GyÆs Sampling Theory in an ambiguous way. For example, the Total Sampling Error is divided into its basic components only in informative annexes, when it should clearly be the main body of the standard. Sampling standards are presently loaded with statistical concepts that actually belong in the annexes. Furthermore, many non-probabilistic sampling procedures are still mentioned which do not belong in a standard. The objective is not to criticise existing sampling standards, but to suggest better ones. Sections on the Sampling Theory should divide the Total Sampling Error into a sum of its nine basic components. Then, and only then, should they be addressed one at the time. Sections for establishing a sampling protocol should address the in situ Nugget Effect, the Fundamental Error, the Grouping and Segregation Error, the Long Range Quality Fluctuation Error, and the Periodic Quality Fluctuation Error. Sections for sampling methods, mechanical sampling, manual sampling, grab sampling, sampling of trucks, railroad cars, bags, and drums should be part of the critically important practical implementation of a recommended sampling protocol, called Sampling Correctness. It includes the increment Delimitation Error, the increment Extraction Error, the Weighting Error, and the Preparation Errors. Unless these errors are addressed one at a time, in an unambiguous way, the standard will remain ineffective in solving sampling problems for the industry. Therefore, a strategy is needed to create better standards required at the early stages of new projects, both by manufacturers of sampling equipment and by engineering firms. A logical sequence of important points that cannot be ignored in any sampling standard is presented. An analysis of the practical use of the words sampling uncertainty versus sampling error is recalled. Finally, as a practical example, an in-depth analysis of the correctness of cross-belt samplers is presented, and emphasis is placed on the correct ways to perform bias-tests for mechanical sampling systems.

Jan 1, 2005

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By Charles Schwab

WHEN I leave this life, as an employer of labor there is no one thing that I want so much to be engraven upon my monument as the fact that I have been one of the men who have worked, whether with my brains or my hands, for the advance-ment of industry in the United States, and to be regarded, as I should like to be regarded by labor with love and kindly remembrance for our years of association. In my relationship with my employees, I have always contended that every man should be paid for what he does. I will not employ or be associated with any kind of labor of which the organization insists that a man shall receive a fixed sum of money for his day's wages, however poor or good his day's labor may be. What applies to the common laborer applies equally well to the management, the brains of an industrial establishment. I have always thought of industry as a three-legged stool, with capital, management and labor as the legs. All three legs of that stool must be there before that stool can stand up. If you take any one of those legs away, it is going to topple over. The. three must stand together for successful business accomplishment. I believe that a man who has his labor to sell, to put it plainly, has just as good a right to bargain for the best price for that labor as those who employ him. It is a perfect right for him to do so. If the government of our United States is right, our method of handling labor in our Bethlehem plants is right because it is representative and democratic. We have our labor elect delegates; elect representa-tives from their own ranks, who shall meet frequently. That constitutes, as. it were, the House of our great Congress in Washington, the industrial house. We have our management, who represent the Senate, who meet independently. Working men have learned to express their views freely as to whether they are treated fairly and whether conditions are right or wrong.

Jan 12, 1922

By E. P. Klier, Volker Weiss, George Sachs

IT has been shown that the isothermal transformation of austenite in a special steel can be modified by isothermal holding in the high subcritical transformation range.' Since this treatment potentially leads to increased hardenability, limited testing has been completed to determine if the stabilization effects observed with this treatment can be used to advantage in the heat-treating of 4340 steel. As an index of the effects of the several austenitizing treatments on the hardenability of the steel, Jominy-type hardenability tests were completed for specimens 2.5 in. in diameter and 8 in. long. Since the steel studied is to be used at strength levels where notch sensitivity is of major concern, notch sensitivity after selected austenitizing treatments has been evaluated by notch tensile tests for several specimen sizes. The steel composition and the austenitizing treatments are given in Table I. The test specimens are presented in Fig. 1. The hardenability data are given in Fig. 2 and the notch tensile properties are presented in Fig. 3. The hardenability of the steel investigated when determined by use of the standard Jominy test specimen2 as high and remained essentially unchanged for the different austenitizing treatments. For the larger test specimen, as has been shown by other investigations," the characteristic hardenability indexes are changed and it becomes possible to isolate austenitizing treatments which promote maximum hardenability. The stepped austenitizing treatment promotes higher hardenability as is indicated in Fig. 2. The evaluation of notch sensitivity for very high strength steels is best accomplished by means of the notch tensile test. The experimental conditions of the test, however, modify the notch strengths measured, and in the present experimentation an effort was made to achieve a limiting notch condition by fixing the notch root radius at 0.001 in. while the specimen diameter was allowed to increase from 0.3 to 1.1 in.* For this root radius the notch strength, 0.3-in.-diam specimen, and this trend differs from that for the larger specimens. At the highest tempering temperatures the 1.1-ip.-diam specimens yield comparable results for the austenitizing treatments compared. However, as the tempering temperature is progressively lowered below 800°F, em-

Jan 1, 1958

By L. W. Jones, B. H. Bennetts

The removal and disposition of large quantities of slag from blast-furnaces is a question of great importance in the design of works, and various methods have been devised, from time to time, in order to take the best advantage of local conditions. With blast-furnaces treating copper-ores or lead-ores, it is necessary to use a fore-hearth, or matte-settler, in order to collect, if possible, every particle of valuable matte which, otherwise, would be carried away with the out-flowing slag. In all of these cases, the slag overflowing from the fore-hearth is caught in pots and then conveyed to the dump. If the slag is of no value and the necessary water-supply, grade and dumping-space be available, the disposal of the slag by granulation is by far the cheapest and best method. It involves a minimum of labor, both at the furnace and at the dump; and it permits a continuous outflow of slag from the furnace or settling-pot, thereby avoiding frequent tapping and plugging. When the conditions of water-supply, grade and dump-area will not permit slag-granulation, there are three other methods in common use. Large steel or cast-iron pots, or ladles, supported by trunnions on heavy cars which are moved by steam-, air-, or electric locomotives; some type of mechanical conveyor; and small pots or buggies moved by hand. The pots on the slag-cars are generally circular or oval in shape, and each one contains from 15 to 40 or more cu. ft. of molten material. The mechanism for tipping them is more or less elaborate; and, as a general rule, the slag is dumped alongside, and quite close to, the track. They are more or less costly to construct and to keep in repair, and, in order to use them to best advantage, it is necessary to have a good elevation of track above the dumping-ground ; furthermore, the rails must be of heavy weight, and well-supported on heavy ties. Other disadvantages of the slag-pots are—1, that the slag cannot be removed continuously

Jan 1, 1906

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By Alberto Oalvez, Lucya Yunus, Pengfii Tan

"Laboratory flotation tests of slow cooled converter slag have showed that 92.5% copper recovery at the copper cut-off grade of 24 - 25 % can be achieved by using a 50:50 ratio of DSP330 and SIBX (sodium isobutyl xanthate) at the natural pH of 7 and with a grinding time of 18.5 minutes. 70ìéç is the P80 achieved at this grinding time. MIBC is the frother and the solid content of the flotation feed was 46%. In the plant trials, two types of collectors at two different feed particle sizes for both the normal and slow cooled slag were operated. The particle size was controlled by the feed rate. The P80 of 75 ìçé at a feed rate between 32 - 36 t/h were tested. The plant trials have demonstrated that the copper recovery in the milling and flotation process of the slow cooled slags was improved by 3%. IntroductionIt is proposed to float the slow cooled converter slag, in the auxiliary circuit of the copper concentrator at Mount Isa, by using the processing conditions identified from several laboratory flotation tests. Among these laboratory tests, one produced a copper recovery of 4 % higher than those achieved from a normal cooled slag with the same slag feed grade and the same copper content (24 - 26 %) in the concentrate. These test conditions were selected for further studies.Laboratory Test Work and Plant TrialsThere has been a lot of work conducted under laboratory and plant conditions [1]. However, the achieved results did not justify their total implementation in the Mount Isa Copper Concentrator. Initially, the lab trials were carried out with slag cooled 100% in air; then it was changed to combined cooling for 12 h with air and 2.5 days with water sprays. The reason for this change was the shortage of space when the slag was cooled 100% in air, as it takes several days to achieve safe temperatures for its removal. The San Manuel Copper Smelter has reported that their slag was left for air cooling in pits for 8 h and then was followed by water cooling for 2-3 days [2]"

Jan 1, 2012

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By Byron Bird

WHILE Mr. Fahrenwald has been working on the fundamentals of ore-dressing, in Idaho, the Northwest Experiment Station of the U. S. Bureau of Mines, in cooperation with the University of Washington, has been studying the corresponding fundamentals for the closely-allied subject of coal-washing. In this work many of the principles outlined in Mr. Fahrenwald's paper have been touched on, one important exception being that phase of his studies where conditions were approximated between those existing on a table and those existing in a hindered-settling classifier. During the past three years this work has been given over almost exclusively to a study of coal-tabling to devise better methods of cleaning fine sizes of coal, particularly the coals of the Northwest, which are very difficult to wash. One important result of this study thus far has been the development of a satisfactory hindered-settling coal classifier, now in use in several commercial plants. Recently table stratifica-tion has been the subject for study. This latter phase of the work with coal,. as well as the earlier portion dealing with hindered-settling classification, has in a measure paralleled Mr. Fahrenwald's work with ore. Without going into details about the results of the coal experiments, I shall merely say that, from a quali-tative standpoint, they are, in general, concordant with Mr. Fahrenwald's, but that from a quantitative stand-point the results, particularly those with, table strati-fication, are somewhat different. These differences may disappear as the work progresses-Mr. Fahrenwald is further ahead with his experiments than we are at the Northwest Station-but if not, the disparity would not be surprising, and indeed would be what one might reasonably expect when investigators work on two very dissimilar materials and use different apparatus and methods of study. However, this- mention of our coal-washing experiments is made only in passing. A principle of general application that may be estab-lished from Mr. Fahrenwald's paper is that different types of stratification should be used in successive' gravity-concentration processes to. obtain best results.

Jan 3, 1927

Prof. J. W. Richards, South Bethlehem, Pa. (in reply to several questions):—The cut representing some of the round briquettes which were under test shows that, at the brcaking-stresses, they break into lumps, and do not disintegrate into powder. The process is simplicity itself. I have followed the different processes for sintering iron-ores and flue-dust, am interested in all of them and wish them all success; but this process appealed to me strongly by its simplicity. It is in line with a method which I once tried to work out myself, but which never came to anything, namely, the agglomeration of fine iron-ores by means of Portland cement. As small an amount as 5 or 6 per cent. of Portland cement will enable fine ore to agglomerate and set into a briquette, but when I came to estimate the cost, I found it was a little too high. The Schumacher process, curiously enough, does not work well on iron-ore, but flue-dust thus treated does harden and give a strong briquette. In my attempts to find a reason for this difference, it has occurred to me that possibly the particles of flue-dust had been coated over with some sublimed silica, which might be an agent in the setting. But I found by experiment that neither sublimed silica, nor ordinary silica, nor ordinary alumina, would briquette. Chemically pure iron oxide briquetted quite hard; but the application of pressure is a necessary part of the operation. If simply moistened with the solution and allowed to stand it does not set hard, but the more pressure applied to it the hardcr it sets. Evidently the flue-dust particles must be pressed very close together in order to get the small proportion of active material wet, so that the particles shall act at their points of contact; for it is evident that only at the points of contact does the cementing action take place. The reactions are facilitated by considerable pressure, bringing the acting particles close together, and may go on with

Jan 1, 1913

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By D. P. Mitchell

Western Australia is the home of much that is new and interesting in the gold-mining industry. Some of the gold deposits are outranked for size and value by nothing yet discorered, while the value of the ores is, in many cases, rivaled only by their complex character. As in all parts of the world, many of the ore-bodies occur in ways which tax the skill of the miner in following them; and among these the writer considers the case of the East Murchison United more interesting than the average. This is one of the leading gold-mines of the colony in point of production, and is situated near the town of Lawlers, in the East Murchison district. The country for several miles around the mine is mainly granite, and the line of outcrop on which this mine is located can be traced for a long distance. As will be seen from the accompanying plan (Fig. I), there are, at the water-level, two nearly parallel veins running slightly north of west. Structural Features.—The most striking peculiarity of these veins, and the hardest to understand, is their tendency to send out horizontal stringers or side-veins. These vary in size from a veinlet an inch thick to a veil] several feet in width, and they extend with great persistence into the wall-rock on either side of the vein. This tendency is shown in Figs. 2 and 3. The usual signs of a movement of the wall-rocks, such as a ribbon-structure of the quartz and a well-defined gouge or seam of clay along the walls, are in many places lacking, while in other places they appear strongly marked. They seem more in evidence below water-level than above. It is a commonlly accepted idea that when a gold-bearing vein loses in width, it often gains in value. In this instance, however, the direct opposite is the case; for in many stopes it has been possible to leave the narrow portions of the vein to act as pillars, and to extract only the wide portions, which are

Jan 1, 1900

By Hanlu Xie, Liang Yu, Ping Wang, Yuanchi Dong

"The leaching process is the first step when recycling BF slag as raw material for some other products. While studying the kinetics of the BF slag leaching process, a fractal phenomenon was found, which indicated some interesting mechanism in the process. The result suggested a new understanding of the leaching process in detail which useful for the industrial applicationIntroductionTypical composition (wt. %) of blast furnace slag varied in a pretty wide range: SiO2 30–40, Al2O3 10–20, CaO 30–40, MgO 5–10.The ground granulated slag is commonly used as base of roadway (mixed with natural inert for paving, soil stabilization, etc.) or one of the resources of Portland cements because of its good hydraulic activity [1]. To recycle the slag economically, the selective recovery of some components of the slag may be considered. As main components exist in the slag, silica [2, 3 and 4] and alumina [4] recovery was first considered.While recovering of silica from the slag, silica gels are recovered selectively from the leaching solution deriving from the treatment of the slag with waste sulfuric acid. After separation of the exhausted solid of leaching, the silica gel is precipitated from the solution at pH 3.2. Although the silica gels obtained by this procedure contain many impurities and need some more work afterward, it is the first and important step for the process.In the prior work [5], silica extraction using blast furnace slag had been investigated, focused on the pH value of selectively silica extraction. In the present work, kinetics of the leaching process was focused. It is important to design an economical process.ExperimentalThe composition of the slag and the calcined gels has been determined by a LINK860 (Oxford Instruments, Oak Ridge, TN) energy dispersive spectrometer (EDS) in conjunction with a CAMBRIDGE S250-M2 (Cambridge Instrument Ltd., Cambridge, U.K.) scanning electron microscope(SEM). The leaching of slag and the precipitation of silica gels have been conducted at atmospheric pressure in a stirred reactor placed at temperature controlled by a heated water bath."

Jan 1, 2008

By Arthur F. Wendt

Within the last few years the production of iron, and of the metals generally, by a given furnace-plant, has been largely increased, in many instances trebled. Iron-furnaces exceeding one hundred tons' capacity per diem are now the rule in new constructions. Copper and lead-furnaces smelting from 60 to 100 tons of ore per day are common. With this greatly augmented product, the life of furnace-linings has been diminished, and recourse has been had to various cooling devices for prolonging the life of such liuings. The object of this paper is to call the attention of the profession to an arrangement recently patented by the writer. The common course of projecting water against the exterior of the brickwork of a furnace has been in a large measure abandoned by our most progressive managers. All have recognized the danger of this proceeding, especially when applied to the crucible of a furnace below the line of the tuyeres. Cast-iron water-jackets, with wroughtiron pipes for circulating the cooling-water, have replaced the cruder methods. In iron-smelting the use of such jackets has been confined to the crucible and the space around the tuyeres; and it has been the custom to support the jackets on the brickwork of the furnace. But the erosion of the brickwork below tuyere-jackets allows them to sag, and often displaces the alignment of the tuyeres and leads to other annoyances. The principle of construction adopted by the writer to remedy this and other evils, is to use a thin fire-brick lining (not over nine inches) from the tuyeres up to the bosh, to back this lining with wrought-iron or steel water-jackets, hung from the mantel-ring, and thus to carry the whole weight of the furnace and its filling upon the supporting pillars. The crucible proper is lined with three or four thicknesses of fire-brick on the sides, and not less than forty-eight inches in the bottom. It is supported on independent pillars, and is practically an independent structure. It could even be placed on wheels and made removable, were there any adequate advantage to be gained by such an arrangement.

Jan 1, 1885

By Frank Firmstone

The furnace from which the brick here referred to were taken, was lined under my supervision and blown-in in May, 1902. It was 75 ft. high and 18 ft. in greatest diameter, and used coke to smelt a lean magnetic iron-ore. The lining was put in as follows:—First, blocks 14 in. long by 6 in. thick; second, 2 in. of loam; third, 13.5 in. of 9-in. fire-brick (one-and-ahalf brick wall) laid in English bond; fourth, red brick to within 2 in. of the iron shell; and fifth, 2 in. of slag-wool between the red brick and the shell. The brand of brick used has been known to me for over 20 years, and in my observation had always proved very durable, notably when used in a small furnace 50 k. high which treated the same magnetic. ore. On revisiting and examining the furnace in March, 1903, it was found that the whole of the lining of 14in. blocks at the top, and for an unknown distance (more than 20 ft.) below, had completely disappeared; and a few weeks later the 13.5-in. lining and the red brick at the top likewise vanished, and the furnace was blown out. N~twithstanding the complete failure of the lining higher up, measurements taken after blowing-out showed no unusual wear in the lower part of the furnace. The exact position in the furnace of the piece of brick-work used in the analysis, given below, is not known; but it came from between 30 and 40 ft. above the bottom. It had formed part of the 13.5-in. wall (no 14-in. brick remaining at that level) and consisted of parts of several bricks so firmly sintered together that fracture occurred indifferently through the joints and through the body of the brick. The joints could, however, be traced by a close examination. The surface which had been in contact with the material in the furnace was covered with a yellowish, translucent glaze, somewhat vesicular, and from

Jan 1, 1904