Search Documents

By Norman Hedley, George Barsky, S. J. Sawinson

The cyanidation of precious-metal ores is a complex chemical process. Numerous reactions occur, some of which cause an undesired consumption of alkali and of cyanide. A knowledge of these reactions, their products, and the factors that influence the rates at which they proceed should be of value in working out the most economical conditions for cyanidation; but at present, much of this knowledge is lacking. This paper is confined to a study of some of the fundamentals of cyanidation. At the start of such an investigation it is necessary to simplify the problem under consideration by eliminating as many variables as possible. The results are then, of course, not immediately applicable to practice, but it is hoped in further work to round out the information and thereby make it of more practical value. For convenience in presentation, the paper has been divided into two parts, one devoted to a study of the reaction between cyanide and gold or silver, the other to a consideration of the factors that determine the rate of dissolution. I. REACTIONS INVOLVED IN DISSOLUTION OF GOLD AND SILVER IN DILUTE CYANIDE SOLUTIONS Ever since the cyanide process for gold and silver extraction was introduced there has been discussion of the equation representing the reactions involved. In undertaking a detailed study of these factors, it was felt that the most logical first step was to determine, if possible, what reactions could theoretically take place when gold and sill-er are dissolved by dilute cyanide solutions. It is possible to determine whether or not a given reaction will theoretically take place by calculating the free energy of the reaction. This free-energy value for any given reaction is the algebraic sum of the free energies of formation of each of the reactants and products, and, if these values are known, the calculation is simple. (A chemical change always involves an energy change and the amount of energy change involved is the factor determining whether a given reaction will take place or how far it will go. In chemistry we consider what is known as the "free energy"; that is, the maximum amount of energy that can be utilized as

Jan 1, 1935

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min. is required to drain and dress the furnace hearth, make up the tap hole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays, because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of' charge. Such general considerations are dealt with first. GENERAL CHARGING PRACTICE Charge materials are discussed in detail in Chapter IV; the present chapter is concerned with the charging, melting, and proportioning of the raw materials in the various types of furnace practice. Charging Equipment and Stock Handling. The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment described in Chapter I (see also Fig. 18, page 33). It is generally desirable to charge the scrap about as fast as the physical volume can be got into the furnace. A limiting factor may be the height to which the scrap may be piled in the furnace without deflecting the flame to such an extent that it will impinge on the roof or walls and thus damage the refractories, but light scrap may often be piled up near the roof since the flame usually "cuts it down" rapidly before impingement on any roof area can persist long enough to do appreciable harm. When the nature of the scrap and the handling facilities are adequate to meet the aim of rapid charging, little thought is given to this feature of operation. Unfortunately, at times

Jan 1, 1944

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By Yun Bai, Ang Chen, Xiangdong Hu, Yanfei Zhu, Gang Li

"It is well known that tunnelling involves a high degree of risk. Conventional risk management only evaluates risks and chooses mitigation measures before the start of a project. However, mitigation measures also introduce risks, which are ignored in the conventional risk control process when choosing different measures. The Multiphase Risk Management Method (MRMM) takes the risk of mitigation measures and dynamic risk control into consideration. This paper introduces this new method and provides a flow chart for better understanding. A case study of the MRMM is given based on Ningbo Metro Line 3, the first quasi rectangle shield tunnel in China. INTRODUCTION Tunnelling itself is generally complex and involves a high degree of uncertainty (Huang, 2006; Thompson and Thompson, 2006). In recent years, several metro tunnel projects in China have been involved in accidents (Wang, 2006; Gong and Zhang, 2012).As a result, Chinese tunnel engineers are paying more and more attention to risk management in tunnel projects (Xiao-lin and Ping et al., 2009; Zhong and Jia et al., 2014), and scholars around the world have put forward many management processes. Existing risk management mainly focuses on a particular stage of a tunneling project. Tunnel engineers or other project parties usually carry out risk assessment and set up schemes or choose mitigation measures before a project begins. The risk from this initial risk assessment may be defined as the initial risk (Bai and Dai et al., 2013). This kind of managing process has been widely used for its simplicity and comprehensibility. However, this static theory cannot properly reveal the dynamic character of the risk during tunnelling. In addition, to reduce the risk from unacceptable level to acceptable level also calls for optimum measures. Therefore, the multiphase risk management method was proposed (Bai and Dai et al., 2013). The purpose of this paper is to introduce and develop the MRMM, and to provide a brief flow chart to illustrate the risk management process based on it. Finally, an example of the first quasi rectangle shield tunnel in China in Ningbo Metro Line 3 is illustrated. It analyzes the initial and secondary risk and sets up a risk control system."

Jan 1, 2016

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

By D. K. Crampton

The object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. Preparation of Material A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1. In fabricating these tubes, rather unusual precautions were observed to insure the elimination of ail variables not under immediate study. All intermediate anneals were carried out at about 1200" F. down to the so-called "cut-in size"; namely, 17/16 by 3/16 in. From this point on, all anneals were made at from 1050' to 1100" F. The greatest care was used all through to have the tubes as free from minor surface defects as possible. When such defects were visible on intermediate sizes they were carefully filed out. On the final draw to 3/4-in diameter the die was aligned with the greatest possible precision in order to insure as straight a tube as possible

Jan 1, 1933

By J. Ellzey Hayden, Lucien Eaton

The Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-conerete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 1, 1922

By W. A. Wood, W. H. Reimann, Maria Ronay

The basic mechanism of fatigue is studied in annealed a brass subjectecl to alternating torsion at room temperature, 100°, 200°, 300°, and 400°C, and in air. It is shown that the slip-zone micro-cracking which characterizes fatigue damage produced by small amplitudes at room temperature is progressively replaced by grain boundary cracking at elevated temperatures, replacement being complete at 400°C. Replacement occurs not because slip activity decreases hut because slip movements at elevated temperatures cease to concentrate in narrow zones and instead disperse. Decrease of amplitude at 400°C through permitting longer lives of specimens before fracture actually causes in- MOST studies of fatigue at elevated temperature have been concerned with data for design. Observations on the basic mechanism of fatigue have been largely incidental, though they have led to the interesting inference that this mechanism has features in common with that of creep.' This paper is concerned primarily with the mechanism itself. Advantage has been taken of mater- crease in pain boundary damage, an anomaly attributed to the greater difficulty at elevated tempwature of starting and propagating a crack. Surface corrosion was most pronounced along slip bands but since at elevated temperatures the slip hands showed no cracking the surface corrosion did not appear to influence onset and early spread of fatigue damage. Similarly the type of fatigue damage produced at room temperature by cyclic strain at large amplitudes, characterized by irregular mi-crocracks at zones between disoriented regions in a grain, was also replaced by mainly grain boundary cracking at elevated temperature, though not so completely. ials and procedures known to show readily how fatigue affects the microstructure of a metal at room temperature, so that direct comparison might be made with what the same procedures show when the material is subjected to fatigue deformation at higher temperatures. 1) MATERIAL This was 70/30 a brass, used extensively in previous studies at room temperature.' Specimens were turned from extruded rod to have parallel test portions 1-1/4 in. long and 7/32 in. diameter, annealed to a grain size -1/10 mm, and electro-

Jan 1, 1965

By Henry D. Hibbard, Edward L. Ford

The process of making washed metal now followed is in principle that described by Holley before this Institute in 1879, as the Krupp washing process. Sir Lowthian Bell also experimented extensively in England during 1877 and 1878 on refining iron and joined his interest with Krupp, the process being often referred to as the Bell-Krupp process. The only plant in this country now operating this process is that of the Brier Hill Steel Co., Youngstown, Ohio. This process may be considered as the sole survivor of the numerous methods conceived for refining crude iron, when the removal of phosphorus from steel-making material was the great desideratum affecting large districts. The east coast of England and all northern Germany, the homes of Bell and Krupp, respectively, could at that time make steel only from imported ores. These processes were in use or in various stages of development 40 years ago and all except the Bell-Krupp received their quietus from the development of the basic steel processes, both pneumatic and open hearth. The aim of the early refining processes was, first, the removal of the silicon, which could be done on a sand bottom, and later, the removal of the phosphorus, requiring a bottom which would give or permit a basic slag. The incidental advantages of increased yield and small fuel consumption were not generally recognized or considered; the aim of the later operations was the saving of the difference in value between low and high phosphorus irons, as well as hastening the removal of the metalloids. The chemistry of the washing process follows in part that of the puddling process, and indeed washing might be considered as the first half of puddling, since all the non-ferrous elements of the crude iron, except the carbon, are eliminated and the iron is maintained molten until cast. In puddling, the iron loses its carbon as well, and because of that, its fusion point rises above the hearth temperature; it freezes into a pasty malleable form, and is worked at once by squeezer, hammer, or rolls. Since Holley's paper, important improvements have been made from time to time in both plants and methods for washing iron, and the

Jan 1, 1916

By J. B. Austin

MEASUREMENTS of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage trans-formed on linear coordinates against time on either a linear or a logarith-mic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even inter-polation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valu-able when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decom-position of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961

By T. T. Read

Personnel work is a term recently introduced to cover the great variety of activities in industrial work that deal with the human factor. Much attention has been focusscd upon individual phases of personnel work, such as accident prevention, sanitation, "welfare" work, reducing labor turnover, and so on. In most cases these activities have been carried on as though they were distinct and separate fields; as a matter of fact, they are only different phases of the single problem of human engineering, and each has important and fundamental relations with the others. Thus, for example, high labor turnover is one of the most important causes of a high accident rate, and unsatisfactory housing conditions are an important cause of labor turnover. In the early stages of the study of these problems, it was necessary to take them up separately; the time has now arrived at which it is desirable to consider them as a whole in order to bring them into the right relation to each other. When thus considered as phases of an interrelated whole, they may be grouped as personnel work. A discussion of the importance of personnel work as a means of increasing dividends in industry may be objected to by some as a too materialistic way of looking upon work that is humanitarian. Nothing could be more mistaken than such an opinion. Humanitarianism, per se, has no place in industry, and nothing is gained and much is lost in pretending that it has. The only reason why a corporation engages in business is to make profits, and any activity of the corporation that does not tend either directly or indirectly toward that end is poor business. It is equally poor business to overlook any activities that do tend indirectly to the making of profits. On this basis, personnel work can be justified as a corporate activity; there is no justification whatever for abstract *humanitarianism from the business standpoint. One characteristic of the American workman is a general high level of intelligence, and it is an insult to intelligence to ask a man to believe that anything so impersonal as a corporation is really desirous of benefiting

Jan 1, 1918

By W. J. Carlson, I. lwasaki

Manganese and silica in nonmagnetic tailings from the direct reduction-magnetic separation step were so closely associated that no physical concentration methods were effective. Dilute sulfuric acid dissolved manganese and iron rapidly; manganese in the form of silicates was virtually insoluble in sulfuric acid solutions, thereby governing the maximum extraction attained by leaching. Autoclave leaching at elevated temperatures and at high oxygen pressures reduced the iron extraction to less than one tenth without affecting the manganese extraction. There was an indication that autoclaving solubilized the manganese silicates appreciably. Elimination of iron from leach solutions was carried out by aerating the solution in the pH range of 6.5-7; a platinum-calomel electrode pair provided a reliable indicator for the end point of iron removal. The purified leach solutions were free of interfering impurities for the recovery of manganese as metal, dioxide, or carbonate. Manganiferous iron ores of the Cuyuna Range, Minn., are too low in iron content to be directly useful as iron ores, and too low in manganese content to be termed manganese ores. Common methods of physical beneficiation such as gravity concentration and flotation have not been successful in upgrading this material. The R-N process, when applied to manganiferous iron ores,1'2 produces sponge iron by direct reduction of iron oxides, while leaving manganese as manganous oxide. From fine grinding and magnetic separation of the reduced ore, a tailing is produced which is relatively rich in manganese and low in iron content. The nonmagnetic tailing can readily be leached with acids and then further processed to recover manganese in various forms. In this way, two processes, neither of which would be an economic solution to the Cuyuna ore problem by itself, may be combined to produce two marketable products, thereby rendering the over-all process economically more attractive. This article reports on the results of a leaching study on the nonmagnetic tailings, both in a batch agitation vessel and in an autoclave; on the problems involved in the purification of leach liquors by aeration; and on the recovery techniques used to produce manganese metal by electrolysis, manganese dioxide either by electrolysis or by autoclaving, and

Jan 1, 1968

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By Yap Chu-Phay

IN 1923, when the writer began his studies in metallurgy, he came upon an article by Professor Honda on the, Equilibrium Diagram of the Iron-carbon System, 1 which made a profound impression on him. What interested him most was this sentence: "In the recent diagram of the iron-carbon system, the solidus is usually shown as a curve bending considerably downward. But it can be shown by thermodynamics that if the liquidus is straight or slightly curved, the same must also be true for the solidus. Hence, in my constitutional diagram, the lower portion of the solidus is slightly bent upward." Ever since then the writer has been interested in thermodynamics, especially chemical thermodynamics. The applications of thermo-dynamics to the metallic systems have been, in the writer's opinion, sadly neglected, although we continually use the phase rule in our study of equilibria in the liquid and solid states of metallic alloys. Many investigators, among whom may be mentioned Heycock and Neville, and s Honda and his coworkers, have applied the simple Raoult-van't Hoff law of depression of freezing point, mainly to determine the heat of fusion, but no attempt has been made to investigate the applicability of the thermo-dynamic laws of solution (as opposed to the laws of solution derived from other sources) to metallic systems" showing either limited or complete solid solutions. Perhaps the reason for this neglect is that until recently there have been so few reliable data on the solidus, which is much more difficult to determine than the liquidus. The writer has under way at the present time an investigation of a number of systems, the solidi of which have been more or less reliably determined. Recently, the writer has not only shown the valid applicability of the thermodynamic laws of solution as applied to the system antimony-bismuth but has also suggested a method of attacking problems involving complete and incomplete equilibria.2 In the present paper, the same method of approach is employed. For convenience, we shall divide this paper into two parts:

Jan 1, 1931

By W. M. Jr. Aubrey, R. L. Stone

INTRODUCTION Most metallic minerals and some industrial minerals have a relatively high specific gravity and most have at one time or another been concentrated by gravity methods. The principles of gravity concentration are straightforward, well documented and easy to understand, but in practice there are many pitfalls that await the engineer in the development of an integrated flowsheet. Gravity concentration equipment has a long history of use and there is a great diversity available. The equipment is capable of treating material over a broad size range, only falling off in efficiency in the very fine sizes. Gravity concentration is also inexpensive, generally free of environmental problems, and commercial equipment can process large tonnages of ore with a minimum of capital cost. As might be expected of an efficient and low cost process, the bulk of the tonnage quickly and inexpensively. Another obvious application is treating mineral deposits such as hematite and manganese ores that are sufficiently liberated after a minimum of crushing to allow production of a coarse concentrate that will meet market specifications. Except for hand picking and mechanical sorting, there is no competing process on coarse size material. Conversely, it is sometimes obvious that gravity concentration does not warrant consideration. Examples are ores that require very fine grinding to attain liberation, for ores where the minerals of interest have a gravity similar to the gangue, and ores that are strongly magnetic. Actually a mineral processing engineer may not know if gravity is the best way to concentrate an ore, but he should have little difficulty recognizing when gravity concentration deserves consideration based upon specific gravity differences and liberation gravity concentration has wide use. size. His challenge then is to At times its selection as the identify and test the applicable primary concentration process is processes, to develop a obvious. Low grade placer deposits metallurgical balance and flowsheet of tin, gold and beach sands usually for the best process, to estimate are only profitable because gravity production rate over the life of concentration is able to throw away the deposit and to make equipment

Jan 1, 1986

By Alden B. Greninger

In a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form {133}. In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form (110), and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices arc body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in marking habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orientation of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix. During the course of the investigation referred to above, samples of 52:48 (stable beta) copper-zinc were deformed and examined micro-

Jan 1, 1938

By P. P. Scott, George C. Howard

During the drilling of wells, fractures which are created or widened by drilling fluid pressure are suspected of being a frequent cause of lost circulation. A study of the variables which are believed by the authors to he related to fracturing led to the premise that the presence of an effective lost circulation material in a drilling mud stream would serve to plug small fractures at the moment they are encountered or created and thereby a a possible cause of lost Circula. tion by preventing fluid pressure from widening and extending the fractures. A large number of lost circulation materials were classified and tested in simulated fractures and in shallow wells. Granular type materials with a gradation of particle sizes were found to be the most effective for plugging. Within the limits of pumpahility, the concentration in mud of each lost circulation material tested was found to be a controlling factor in determining the maximum size fracture which could be sealed. A new type centrifugal sorter was given preliminary tests and found to be capable of concentrating cuttings for rejection and reclaiming lost circulation materials. INTRODUCTION The control and prevention of lost circulation of drilling fluids is a problem frequently encountered during the drilling of oil and gas wells. Lost circulation or lost returns may be defined as the loss to formation voids of the drilling fluids or cement slurries used in the process of rotary drilling and well completion. The loss may vary from n gradual lowering of mud level in the pits to a complete loss of returns. Not to be confused with lost circulation is the continuous reduction in mud volume caused by the loss of the fluid phase of muds as filtrate and the solid phase as filter cake during the continuous filt~ation process which occurs on permeable formation surfaces. The loss of drilling fluids and their costly constituents is only one of the detrimental effects experienced when circulation is lost. The loss of drilling time, plugging of potentially productive formations, stuck drill pipe, blow-outs, excessive inflow of water, and excessive caving of formatioils are other effects which contribute to make the control and prevention

Jan 1, 1951

By J. H. Fletcher

ALTHOUGH some mines have been completely mechanized, on the whole mechanical equipment has made slow progress in the coal fields. Coal mining is particularly well adapted to hand labor. The skillful hand miner can keep his working place safe under difficult roof conditions, remove impurities from the coal at the point of origin, and produce a maximum percentage of large-size coal, so as to command the highest price on the market. Hand mining has also the advantage of low capital investment per ton of production and moderate carrying charge when the mine is idle. Though animal haulage gave way to electric locomo-tives and hand cutting to mining machines, beyond these concessions most of the tonnage is still produced by manual labor. But factors over which producers have no control are speeding the change to mechanical mining. The additional investment in underground equipment and surface preparation plant must be offset by a great increase in tons per man-day, and to do this the employees should be able to utilize as much of their time as possible on production. In the installation of mechanical mining, the only change in method usually has been to add loading machines to a mine already developed for hand loading. Because of a lack of suitable equipment, few mobile loading machines have been installed in seams of coal less than 4 ft. thick; the mechanization in the thinner seams has been confined largely to shaking conveyors and hand loading onto chain conveyors. Mechanical mining requires an organization that is prepared to study its particular problem from production territory to market in recognition of the changed factors arising from the use of loading machines at the working face, and other causes, such as safety of men and property; high wage scale on hourly basis; concentrated working territory and rapid extraction from a given area; change in the percentage of sizes of coal produced and effect of this on average realization. There are also the coal-cleaning problem; increased capital investment, maintenance, obsolescence, and the relation of all these to the spread between realiza-tion and production cost. If coal seams were uniform, the answer would

Jan 1, 1939