Search Documents

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1949

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By C. K. Stoddard, R. G. Knickerbocker, E. T. Leidigh, R. R. Lloyd, K. L. Mattingly

DURING July 1941, a study was initiated at the Boulder City Experiment Station of the Bureau of Mines on proposed methods for the production of magnesium metal. The major emphasis was placed upon development of a process that required minimum reliance upon the sale or utilization of by-products to meet economic competition from processes already in operation. It was felt that only through the development of such a process could the nation's vast resources of dolomite and low-grade magnesite that are contiguous to large blocks of firm power be properly utilized. During the course of exploratory tests on electrolytic and electrothermic processes, it was noted that fused magnesium chloride would dissolve appreciable quantities of magnesium oxide in the presence of small amounts of boric oxide. The use of such a solution in an electrolytic cell employing a graphite anode and a steel cathode caused the deposition of magnesium at the cathode and the evolution of carbon oxides at the anode with minimal amounts of chlorine The original results were sufficiently encouraging to justify further investigation on an enlarged scale, since the process seemed to present advantages over other proposed processes 1.2 for the direct use of magnesium oxide in a fused chloride electrolyte. When work on a larger scale was initiated it was found that the addition of boric oxide to the electrolyte resulted in dispersion of metal and constantly decreasing current efficiency. However, by this time solubility studies had shown that magnesium oxide was sufficiently soluble in magnesium chloride melts containing no boric oxide to effect the same anode reactions, and development work was continued. Over two years of development work have been carried out, and considerable work remains to be done. It is desired to emphasize the fact that many of the difficulties met require a long period of continuous operation before they become serious enough to affect operation of the cell. ACKNOWLEDGMENTS This paper is one of many reporting on various aspects of the Bureau of Mines' program initiated in August 1939 by passage of the Strategic Minerals Act the scope of which was greatly expanded by subsequent legislation. Some of these papers are published as war minerals reports. others as bulletins, technical papers, reports of investigations

Jan 1, 1945

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definitive life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENTVALUEOFAMINERALPROPERTY In essence the present value of a mineral property is a sum of money in today's dollars that future earnings from the property are worth. It differs

Jan 1, 1959

By J. Ellzey Hayden

THE Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-concrete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made, the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard' were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to Mr. W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 8, 1920

By Heinrich Freyn

THE American iron and steel manufacturer finds himself to-clay barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels. The fuel cost is by no means the smallest of items which enter into the cost of manufacture of iron and steel products, but the great wealth of this country in high-grade fuels, together with a protective tariff, has heretofore made fuel economy relatively unimportant. In Germany, the use of raw coal for the purposes of iron and steel manufacture has been all but abandoned and large sums of money, formerly irrevocably wasted, are now being saved. When scanning the literature of this country devoted to the application of gas power, but little information will be found on a subject which, however, is destined to become of considerable importance in the United States, namely, the use of coke-oven gas for the generation of power in gas engines. This lack of information can be traced to the fact that the regenerative by-product coke oven with its large amount of surplus gas is still far from having attained in this country the universal application which it has found in Europe. This statement needs hardy any corroboration other than the evidence of statistical investigations made by E. W. Parker of the United States Geological Survey, according to which only approximately 25 per cent. of the total coke produced in this country in 1912 was made in by-product coke ovens, whereas 75 per cent. was produced in bee-hive ovens. This entailed the enormous loss of over $80,000,000 in non-recovered by-products, such as gas, tar, and ammonia, without considering the substantial loss due to the non-recovery of benzol from the coal. There are two more or less distinct fields of application of the by-product coke oven: one, to furnish as the main product metallurgical coke of specified quality, and surplus coke-oven gas as the by-product, and the other, to carbonize high-volatile coals, and thus produce as the main product large quantities of gas, high in heat value and rich in illuminants, adapted primarily for domestic heating and lighting, while domestic coke becomes the by-product.

Jan 4, 1914

By O. W. Ellis

Before entering upon a general discussion of the fascinating, but at present rather controversial, subject of gases in copper, the author feels that some attention should be directed to the work which has been carried out on the solubility of gases in metals. The outstanding contributions to our knowledge of this subject have been made by Sieverts and his collaborators(1) † and by Iwasé.(2) Both the German and the Japanese investigators employed apparatus of the same general design in their investigations. Full reference need only be made, therefore, to the German scheme, which is diagrammati-cally illustrated in Fig. 1. This, to use the words of Sieverts, which he employed in describing his arrangement of apparatus at the 1928 meeting of der Deutschen Gesellschaft für Metallkunde(10): shows a diagram of the usual mode of procedure. A quartz flask contains the metal (for high temperatures a highly refractory porcelain tube is used) and is connected with the rest of the apparatus by means of a stopcock. The other parts consist of a burette divided into 1/10 c.c., a leveling tube, and an adjustable mercury reservoir. The burette is connected on one side with the gas inlet and on the other side with the absorption flask; the connection can be interrupted by means of suitable taps. Another tap permits the connection of the flask and the Töpler pump. In an experiment the quartz flask is first exhausted and then a measured quantity of gas is let in from the burette. In the first place the volume of the flask when empty is found by calibration with an inert gas. The pressure is read off on the level tube of the burette, and the temperature measured by means of a thermocouple whose welded junction lies close to the outside of the quartz flask, which is heated in an electric furnace. In several experiments the quantity of absorbed gas was transferred to a burette by means of a pump and measured. Care was taken by Sieverts to cool the ground-in joint between the reaction flask (or tube) and the rest of the system. Suitable precautions

Jan 1, 1934

By E. B. Olds, B. P. Burt

The mines of the Consolidated Gopper-mines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 11/2 miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1949

By B. M. Larsen

AN increasing amount of attention is being paid to the possible influence of oxygen, in its several modes of occurrence in steel, upon some of the properties of the metal; but clearly investigations along this line are unlikely to yield significant results until reliable analytical methods for the determination of oxygen have been established. This paper presents some results of a study of an improved Ledebur method which aims to determine a definite portion of the oxygen; namely; that which presumably is present in diffusible form in the. solid steel. These more or less preliminary results lead us to believe that the oxygen so determined has some significance; their presentation at this time will, we hope, stimulate discussion of, and focus attention upon, certain rather neglected aspects of the problem. Considerable work has been done recently on methods of estimating inclusions and on the vacuum-fusion method for oxygen; with results which, however, are of somewhat questionable significance. It is commonly presumed that the oxygen in a bath of molten steel in a furnace is present partly as a separate phase consisting of suspended particles of oxides or silicates, partly in solution, the latter being probably the more important. Upon addition of a deoxidizer, it reacts with some portion of the dissolved oxygen and precipitates it as additional suspended particles; the oxygen not eliminated in this way, which remains in solution in the liquid steel, may be regarded indifferently either as dissolved oxygen or as dissolved FeO. When the steel is poured, some of the suspended particles rise towards the surface, others remain trapped in the finished steel, appearing as nonmetallic inclusions in amounts corresponding usually to about 0.01 to 0.03 per cent 02 in the steel. The dissolved oxygen may be partly eliminated as CO during freezing of the ingot, but some remains either in solution or in part precipitated as FeO. Finished steels may thus contain oxygen in several forms: (1) In non-metallic inclusions which are probably quite insoluble in the solid metal at all temperatures; (2) in solid solution which at lower temperatures may be supersaturated; (3) in FeO particles produced by relief of this

Jan 1, 1932

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By L. F. Mondolfo

An investigation of the relationship between properties of the elements and type of binary diagram formed was conducted. It was found that, for each type of equilibrium diagram, the factors for the size, valence, electronegativity, period, melting point, entropies of fusion, and sublimation calculated for each pair of elements cover a range of values. However, these factors show sufficient relationship to the equilibrium diagram so that the correlation of several of them can be used to predict the type of diagram formed, or at least limit the choice to only a few types. ThE goal of the metallurgist concerned with alloy development has always been to find a method that predicts the properties that can be obtained when a certain metal is added to another one. In most cases a qualitative predictiton of properties can be made if the equilibrium diagram is known. However, this means that for new metals the alloy development has to start with the experimental determination of the equilibrium diagrams. Because this determination is at least as complicated and time-consuming as the determination of the properties themselves, most alloy development has taken place by trial and error, and the study of the equilibrium diagrams has followed rather than preceded the creation of new alloys. Alloy structures and properties depend on the interaction between electrons and a complete knowledge of these interactions would permit prediction of structure and properties of alloys. Unfortunately direct measurement of these interactions is extremely difficult and somewhat doubtful and only properties that depend on them can be measured easily and with certainty. Study of the relationship between properties of the elements and equilibrium diagrams is not new. Besides the well known Hume-Rothery rule of the necessity of an atomic diameter fit within 15 pct for extensive miscibility in the solid, and the wide knowledge of the effect of such factors as size, electronegativity, electron-atom ratio on solid state features,"' work relating to liquid state and liquid-solid reactions can be found in the literature. Of particular interest is the work by Axon,3 who investigated the effect of size and melting point on a selected number of eutectic and monotectic dia-

Jan 1, 1962

By J. W. Gwinn

The underground haulage system in the lead-silver mine of the Bunker Hill & Sullivan Co., situated at Kellogg, Idaho, is the most extensive in the Cæur d'Alene district, comprising about 35,000 ft. of tunnels, drifts, and cross-cuts where locomotive haulage is in use. The main working adit, known as the Kellogg tunnel, or No. 9 level, is approximately 10,000 ft. in length from the portal to the main working shaft and extends beyond that about 4,500 ft. in each of two directions. On this level all the ore from the Bunker Hill & Sullivan, the Sierra Nevada Consolidated, and the Caledonia Mining Co.—an average of 44,600 tons per month—is hauled to the mills, located a short distance from the portal. Electric haulage by the trolley-type locomotive is used on this level throughout. Below this level, at intervals of 200 ft. vertically, are five other working levels (Nos. 10, 11,12,13, and 14); and the total haulage distance on these, where electric locomotives are used, is approximately 16,000 ft. No. 13 level has but recently been opened up and is not working to capacity; while the main cross-cut on No. 14 has just been started, and has no need of power haulage. Of the four levels equipped with electric haulage, Nos. 11, 12, and 13 have storage-battery locomotives, and No. 10 still retains the trolley type by reason of the small and decreasing tonnage produced. Electrification - Electric power is supplied to the mine by two systems. The first, the 500-volt direct-current trolley, was installed in 1897 when the Kellogg tunnel was started, and was extended as the tunnel advanced, being used for the first trainload of ore on Nov. 17, 1902, since which time it has been in continuous service. The current for the line is transmitted on a No. 00 copper wire as far as the shaft, and on No. 0 wire throughout the remaining length of the Kellogg tunnel; and until the installation of the storage-battery locomotives it was used in practically all the cross-cuts and drifts on each level below No. 9.

Jan 1, 1915

By Chester A. Fulton

In Polk County, Florida, the mining of raw phosphates began some 50 years ago with dredging operations on the Peace River, and in other near-by places by removal of shallow overburden with negroes and wheelbarrows, or with mules and scrapers, and the excavation and screening of deposits found close to the surface. There were many individual operations of comparatively short life. Later steam shovels removed the overburden, and still later hydraulic methods were substituted for the steam shovel. Within the last 10 years large electrically operated draglines have almost entirely replaced hydraulic mining for overburden removal. The matrix is still mined by hydraulic giants and pumped to the washer or recovery plant. The many small operations have long since disappeared and the most desirable phosphate lands have gradually been acquired through purchase or merger by the seven companies that are operating in the field today. These companies are producing and selling about 2,000,000 long tons of phosphate per annum, or about two-thirds of what the industry likes to think is the normal output, with 1929 and 1930 in mind. To produce these 2,000,000 long tons of raw phosphate, they mine and treat about 1,000,000 tons of tailings from older and less efficient operations, about 11,000,000 tons of matrix, and remove from above this matrix some 22,000,000 tons of overburden. The mining practice that has made possible the excavation and handling of 34 million tons of material to win but 2 million tons of merchantable product, selling for probably an average of only $4 per long ton when dried, should be of interest to the mining profession, though little has been written of it. The Florida Pebble Field, as it has come to be known, comprises an area (Fig. 1) within a radius of about 18 to 20 miles centering around Mulberry in Polk County, a small town 30 miles east of Tampa, Florida's largest port on the Gulf coast. The geology1 of these phosphate pebble deposits may be described briefly. A fairly pure limestone was altered to a secondary apatite.

Jan 1, 1938

By F. W. Miller

A brief history of byproduct coking in Alabama with short general descriptions of plants and the state's production of beehive and byproduct coke. PRIOR to the Civil War, there were several small charcoal furnaces for smelting the brown limonite ore that is found, in comparatively small bodies, throughout the central and north-central portions of the state. During the Civil War, these furnaces furnished charcoal iron to the Confederate Government. No attention was paid to the large bodies of lime-bearing hematite ore that now supplies the bulk of the ore used in the various blast-furnace plants of this district until the latter part of the 19th century. Red Mountain, which is the southernmost and one of the smaller ranges of the Appalachian Chain, lying immediately south of the Birmingham and Bessemer, is the principal source of this ore. The orebody outcrops on the northern face, extends through the mountain, and underlies Shades Valley on the southern side. When it was found that these ores could be worked satisfactorily in the blast furnaces, there was a comparatively rapid growth in the blast-furnace industry in the Birmingham district. As these ores are far more refractory than the limonite ores, this blast-furnace development was accompanied by the construction of beehive ovens to carbonize the coal, in order to supply the necessary fuel. The state's production of bee-hive coke in 1880 was 60,781 tons; ten years later this had increased to 1,072,942 tons; and, in 1897 the production had reached 1,443,017 tons. In 1898, the first byproduct oven built in the state was put in operation. This plant consisted of 120 horizontal-flue Semet-Solvay ovens, three flues in height by thirty flues in length with an average width of 16 in. The plant was constructed by Semet-Solvay Co., for the Tennessee Coal, Iron & Railroad Co., and was located adjacent to the blast-furnace plant of that company at Ensley. Coal was delivered from the Pratt mines, by gravity tracks, directly into bin's of the ovens after having

Jan 9, 1924

By L. A. Mekler

The recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to those produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack. The convection-type oil still is particularly suitable for the application of flue-gas recirculation. In an oil still, the heating of the oil is accomplished by applying to the tube surfaces a given quantity of heat of a certain predetermined quality, usually with the initial temperature of the gases not over 1500" F. as measured by thermocouples placed above the tube bank. To obtain the full benefit of the heating surface of the coil, the final temperature of the gases, after passing over the coil, is kept 200" to 300" higher than the temperature of the incoming oil. This final temperature varies from 500" F. for a topping still with only a slight or no

Jan 1, 1928

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

By L. D. Jaffe, M. R. Norton, J. H. Hollomon

In the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermalt‡ decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work.§ Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. Method In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1947