Search Documents

By J. H. Mallery, J. H. Keeler

THE crystal structure of Zral, the compound richest in zirconium (91.03 pct Zr by weight) in the system Zr-Al, has been found to be ordered face-centered-cubic. This compound is of particular interest, since it is encountered as the precipitated phase in potentially useful zirconium-rich alloys. It forms peritectoidally from body-centered-cubic zirconium and Zr,Al at about 975°C. The Zr-A1 constitution diagram has been reported by McPherson and Hansen.' For the primary determination a 100 g ingot was prepared by arc-melting in a water-cooled copper crucible under purified argon. The raw materials were crystal-bar zirconium (a purity of better than 99.7 pct) and spectroscopically pure aluminum. The ingot was double melted, examined metallographi-cally, and found to be quite uniform as shown in Fig. 1. The hardness of the as-cast button was VHN 390 to 445. A 20 mil diam specimen was prepared from annealed (900°C) filings of Zr,Al. The specimen was mounted in a 5 cm radius powder camera and an 8 hr exposure was taken using copper radiation with a nickel filter. The structure of the compound Zral was found to be ordered face-centered-cubic of the Cuau type, with an a,, value of 4.37220.003A. Its calculated density is 5.976e0.013 g per cu cm. The relative intensities for the lines were calculated using the formula 1+cos2 20 I oc----------------- • p • /F7 sin2 0 cos 0 1 + COS' 20 where----------------is the Lorentz polarization fac- sin2 0 cos 0 tor, p is the multiplicity factor, and F is the structure factor. The X-ray data are given in Table I. The compound has exhibited plasticity when present as particles in a matrix of a zirconium. During hot working at about 900°C, the compound has been found to deform plastically to the extent that some of the particles exhibit a length-to-width ratio greater than 4:1 as shown in Fig. 2. In answer to the discussion of ref. 1, McPherson and Hansen pointed out that the compound may be cold rolled and reduced as much as 33 pct. Zr,Al has also been found2 under certain conditions to precipitate in lamellar form at grain boundaries of the a phase of hexagonal-close-packed zirconium. Acknowledgment This work was carried out under Contract W-31-109-Eng 52 for the United States Atomic Energy Commission.

Jan 1, 1956

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8.9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3-s in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6.9 The measure of internal friction adopted here, I/Q, is (p) X the logarithmic decrement, a measure used by some writers, and is also (I/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°°C. As shown in Fig. i, the internal friction increased by only a factor of 2 from room temperature to 300°°C., then by a factor of 100 during the next :too' interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction ~ e-HI/RT [I]

Jan 1, 1942

By L. D. Jaffe, D. C. Buffum

The importance of temper brittleness in alloy steels has long been realized in Europe. In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. Interpretation of Previous Data For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.' One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 45w550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness. If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2J found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.'-= The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture. If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1949

By John M. Gallow

Discussion of the paper of JOHN M. CALLOW, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2321 to 2339. R. H. RICHARDS, Boston, Mass.-I think there is one note which would be interesting to have recorded in connection with this paper, and that is another form of flotation machine. The Minerals. Separation machine has a vortex action, with a vertical shaft and a propeller. This new frother has been developed for the Copper Queen Co. at Bisbee, Ariz. It has a horizontal shaft and a paddle wheel for a frother. It has eight cells, I think, all connected underneath in one continuous tank, and the only separation of the cells is in the upper chambers where the froth is. When this paddle wheel goes around it throws out the froth and the sand goes to the bottom and drifts over from the first to the second cell, where it is paddled again, and comes out with its froth; the sand goes to the third cell where it is again beaten. In that way the sand is continually drifting toward the last cell, while each new froth remains in its own cell. You can see in the working of this machine just the same effect that you see in Callow's machine, i.e., the earlier cell has the darker or richer froth, and the latter has the lighter or poorer froth until you get to the farthest one-which has very little froth, and is very light. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-Speaking from the metallurgical standpoint, it is quite desirable, in many cases, that the oil be removed from the concentrate in order to facilitate the metallurgical work, and I think attention should be directed to the desirability of removing from zinc sulphide concentrates the oil which interferes with their subsequent roasting. The value of the oil is not large; in Mr. Callow's plant, for instance, it would be $20 a day, and it may be possible that a process might be developed which, within the limits of the value of the oil, would remove it, and thus facilitate the metallurgical treatment. LEONARD WALDO, New York, ,N. Y.-The question came up about a year ago as to why-Mexican crude was not an admirable oil for flotation. I have never heard any satisfactory answer to the question. The Mexican crude has the peculiar property of comparative freedom from dangers of fire, a very great reluctance to part with its water, and a specific gravity almost identically the same as water.

Jan 5, 1916

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By Carl F. Floe, John Chipman

A YEAR ago the authors published a paper on the solubility of sulphur dioxide in molten copper.1 The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: [ ] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above l00 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu20 and (a; 2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of SO2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. EXPERIMENTAL METHODS The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By Luis Elek

DEVELOPMENT of the cement industry in Mexico began some 40 years ago. It has gradually reached great importance in the economic life of the country and has contributed greatly to the technical and economical advances which have been so noteworthy, particularly during the last 15 years. From a modest start, the industry now comprises 18 cement-producing plants having a potential annual capacity of approximately 14 million bbl. About half the plants were built and equipped with secondhand machinery during the last world war when no new machinery could be procured. They will hardly attain full production before being modernized and reconditioned, a job now under way in several of the plants. At present, the yearly consumption is only about 8 to 9 million bbl but is steadily increasing. This is only a fraction of the cement consumed in the U.S.A., which is about 250 million bbl per year, although on the basis of consumption per capita per year, the figure is 1/3 bbl for Mexico and 1 2/3 bbl for the U.S.A. Cement consumption in Mexico is well above the average of all other Latin American countries, with the exception of the Argentine, and considering the potentialities and undeveloped riches of Mexico, the road construction and irrigation works, it is fair to assume that the Mexican cement industry will still prosper and expand in spite of temporary setbacks in the future caused by local events of economic or political nature. Portland cement is manufactured by burning a mixture of raw materials, one of which is mainly composed of calcium carbonates and the other of aluminum silicates. The most typical materials answering this description are limestone and clay, both of which occur in Mexico in many varieties. To be usable for cement manufacture limestone should contain at least 77 to 80 pct calcium carbonate. Lower grade limestone can be used for cement manufacture only if the lime content is increased by the beneficiation process, which has not yet been adopted by the Mexican cement industry. Most of the limestone used by Mexican cement plants has a calcium carbonate content of 90 to 95 pct and therefore requires addition of one or several correction materials. A typical composition of raw mix for cement manufacture is 85 pct limestone and 15 pct shale, clay or volcanic materials. Occasionally it is necessary to add a smaller amount of sand or other siliceous material to increase the silica ratio in the raw mix. Likewise, it is sometimes necessary to add 1 or 2 pct iron ore to facilitate fusion in the kiln and to obtain proper relation between alumina and iron oxide. After calcining and

Jan 1, 1953

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989

By Henry S. Drinker

THE Butler Mine property is situated in the vicinity of Pittston, in the Wyoming coal-field of Pennsylvania. The coal has been worked out from the fourteen-foot or Baltimore vein for a number of years on part of the tract, the old chambers remaining open as when originally abandoned. This vein outcrops on the Butler property, and is nowhere more than sixty feet below the surface of the ground on the line of the cut-off to be described. Above the fourteen-foot vein and about, say midway, between it and the surface of the ground, there is another small vein or rider of coal, about twelve inches in thickness. The rock between the two veins is a carbonaceous slate, about twenty-five feet in thickness. Above the smaller vein is a bed of sandstone, varying in thickness, but generally not less than from eight to ten feet. This sandstone is also carbonaceous, but the proportion of carbon is much less than in the slate below. Both rocks have been analyzed, and before the next Institute meeting, the writer hopes to be able to furnish the exact proportions. The sandstone is overlaid with debris up to the surface of the ground. Some time during the spring of 1876, it was found that the coal left in the worked-out mine had been set on fire, and that the fire was gradually spreading. Inquiry developed the fact that the fire had originally been started by a woman, who had taken up her abode in an old tunnel leading into the workings. Owing to some delay in the early attempts made to extinguish the fire, it finally gained such headway that no ordinary means were found to be effectual. Finally, Mr. C. F. Conrad, civil and mining engineer, of Pittston, Penna., was called in as consulting engineer. He advised the making of a thorough cut through such portion of the old workings as had not been reached by the fire. It was found by survey that this cut could be limited to a length of about one thousand two hundred feet, as the vein faulted on both sides, and that the greatest depth of the cut would be about sixty feet. Subsequently it was decided to tunnel part of the way, thus saving the deepest portion of the cut. In 1856-7, there occurred a fire in the same mine. Two stone-walls in V-shape running from the apex of the V towards the outcrop, were built to cut the fire off, and these walls were carried as far as the vein had at that time been worked. After the walls were finished

Jan 1, 1879

By V 7. 0 / 300 dpi

LAST fall, having a number of ore samples from mine-development work carried on in spite of the "Revolution," I was forced to do my own assaying again, after a lapse of many years. This gave me an opportunity to build a furnace for crucible assaying, using wood for fuel, along lines which had been developing in my mind since the time 20 years ago, when as general factotum at a little mining camp in western Chihuahua, Mexico, I had converted a crucible charcoal furnace into one using the reverberatory principle. Wood-burning furnaces have been described in technical literature, but I believe the present application will prove helpful to those of the profession who are working in out-of-the-way places. The furnace is shown in detail in Figs. 1, 2 and 3. Remembering the trouble caused by stoking my first charcoal furnace too heavily, I fired this one with but a few sticks of wood at a time. By this method I could run out a charge of 12 crucibles in 30 to 35 min., using 50 sticks of ordinary stove wood. Later I fill up the firebox, holding about 40 sticks, get everything ready, put the crucibles into the melting chamber and "fire up." Just as soon as the fire is well started the draft door is closed and the furnace allowed to heat up slowly for 5 min. Then the draft is opened (the door to the ash-pit) and the fire allowed to roar, which it does. In 20 min. from the time the fire is lighted the fire door is opened, the fire stirred along the grates, and 5 or 6 more sticks of wood thrown in. In 25 min. from the start, the draft is closed again, the cover of the melting chamber pushed back and the charges poured. The melts will be found to be perfect, and the crucibles to pour absolutely clean, if everything has gone right, as will usually be the case. A new charge may be put in, and fired with S to 10 sticks of wood at a tine, and be ready to pour within 20 min.; but it is just as well to leave the crucibles in the melting chamber a full 2.5 min. By using 10 sticks of wood to start the fire and adding 5 sticks as often as needed, which will be as soon as the last sticks fed in are in perfect combustion, the smelting can be completed in from 30 to 35 min., using from 35 to 40 sticks of wood. I consider this to be the best method of stoking.

Jan 10, 1914

By Jean-Michel Rendu

That you are giving the Daniel C. Jackling award to me is a great personal honor. But more significantly, it is a recognition that geostatistics has come of age. And since I am considered by many as belonging to an older generation of geostatisticians, I thought that it would be fitting that I reflect on where geostatistics came from and where it might be going. First, though, let me propose a definition of geostatistics. Etymologically, paraphrasing Webster's definitions of "geo" and "statistics," it is "a branch of mathematics dealing with the collection, analysis, interpretation and presentation of masses of numerical data taken from the earth." This definition is most appropriate in the context of mining geostatistics. It includes both classical and spatial statistics. It emphasizes the earth aspect, or the analysis of geologic features. And it should remind the practitioner that geologic input is a critical part of all geostatistical applications. In the 1910s, statistical methods were already used to analyze geological data. However, the origin of geostatistics, as we know it today, is best set in the late 1940s, when H.S. Sichel recognized the lognormal distribution of sample values in the South African gold mines. In 1951, Daniel Krige observed that "it can be expected that the gold values in a whole mine will be subject to a larger relative variation than those in a portion of the mine." In other words, samples taken close to each other are more likely to have similar values than if taken farther apart. This observation is the foundation on which spatial statistics, which characterizes values defined in a multidimensional space, is built. However, the 1950s were marked by studies based on classical, as opposed to spatial, statistics. It was only in the 1960s that the need was recognized to model the similarity between sample values as a function of the distance between samples and that the semivariogram was defined. A theoretical framework was developed by Matheron that supplied an elegant mathematical explanation to the empirical observations made by Krige. Matheron coined the term "kriging" in recognition of Krige's pioneering work on the geostatistical evaluation of mineral deposits. As soon as this theoretical framework was developed, it was possible to bring geostatistics to the academic world. The "Centre de Geostatistiques" was founded in Fontainebleau. Numerous students were trained there, disciples eager not only to improve the theory and develop more sophisticated mathematical tools, but also to spread the new faith throughout the world. Expansion of geostatistics exploded in the 1970s, arguably the most fertile decade if it is judged by the frequency of theoretical breakthroughs, the number of original publica-

Jan 1, 1995

SINCE I have mentioned the art of alchemy in. many parts of this treatise of mine, especially when 'came to the description of the practice of various operations,* I do not here intend to argue as to whether it may be called true or not. But in case it is true, inasmuch as it is seen in operation to be a result dependent on the actions and virtues of fires, I should not pass by in silence without speaking at all of this art here, nor would I wish to do so, especially since I think that you do not really know what it is except in so far as common report is heard everywhere to the effect that whoever carries it to completion makes silver and gold with it. Because of this belief, many seek it with much time, labor, and expense, as I know you have often heard related, if not elsewhere, by me in the chapter on gold that I have written in this volume. Now do not think that I wish to teach you this art here, for I am one of those who do not know it. Therefore I shall tell you here, so that you may know more, only. that those workers who so eagerly follow after and seek it proceed by just two pathways. One is that which takes its enlightenment from the words of the wise philosophers, by means of which they think to attain it. This they call the just, holy, and good way, and they, say that in this they are but imitators and assistants of Nature, indeed, manipulators and true physicians-of .mineral bodies, purging them of superfluities and assisting them by augmenting their virtue and freeing them from their defects. In this way they sometimes proceed to corrupt these bodies in order to be able to separate the elements they contain so as to reduce them, if possible, to their primary materials, as they call them, or sometimes they convert them into new substances by means of this art or by adding another spirit different from the first one. Thus they seek in this way to bring these materials to a certain point of corruption or to a separation of elements, or to remove or add spirits to things, or to make coarse materials subtle and sometimes to make subtle materials coarse. Therefore, as you can understand, these persons, with bridle broken, run a circular track night and day, without ever having rest; and surely I do not know whether anyone has ever arrived at the desired goal. Nevertheless, even though the goal of this art were emptiness, as many

Jan 1, 1942

By Franz E. Pawlek

Synopsis This is a summary of investigations in the field of pressure leaching carried out at the Institute for Extractive Metallurgy of the Technical University of Berlin-West during the last seven years. The efficient dispersion of gas in a liquid and its dissolutions as well as the events at the phase boundary when leaching ZnS are reported. At the end two examples are given for the use of pressure leaching in the processing of smelter by-products. INTRODUCTION About 20 years ago, experiments were independently started in Canada and in Berlin on the subject of dissolving sulfidic ores without preliminary treatment by means of leaching under increased oxygen pressure. In Canada ammoniacal solutions were mainly employed, and F. A. Forward and his co-workers were successful in applying this process on a large industrial scale1, 2. This process is used in Fort Saskatchewan to produce about 15,000 tons of Ni per year. In Berlin, investigations were started on leaching with acid solutions3, 4. This process had also been used on a large industrial scale in the D.S.A., but the choice of unfavourable working conditions led to great difficulties, and to giving up this process for industrial use. Later on in Berlin work was carried out especially on the kinetics of pressure leaching 5, 6, 7, 8, 9 and its applications to the processing of smelter by-products, in particular of mattes and speisses10, 11, 12, 13, 14. The dissolution of ores and by-products can be subdivided into four steps: 1. the efficient dispersion of the gas, so that its dissolution occurs over as great a surface area as possible, since only the dissolved oxygen reacts with the solid, 2. the suspension of the solid, so that the entire surface can take part in the reaction, 3. the phase boundary reaction, 4. the removal of the reaction products. The first two steps belong to the field of process engineering and will be discussed from this point of view. The aim of these experiments15 was to find out first of all the limits of efficiency of self-sucking stirrers in solutions of low viscosity with regard to the mass transfer. In addition, the effect of ultrasonics in the same reaction system was studied. The experiments were carried out in a lucite container as shown in Fig. 1. Four baffles of 0.1 d width were in the stirring vessel. The height of these baffles was adjustable. For every experiment one litre of liquid was used. An infinitely variable direct current motor, which was fixed with a hollow shaft, served as the driving power for the stirrer.

By A. Bain

The use of plastics in the coal mining industry is making slow progress whereas these materials could make a greater contribution to safety, to a reduction of working costs and to the higher productivity of mine workers. Possibly the reluctance to experiment with the new material of our age is due to the low profit margin of coal mining. This note has been prepared to present a brief survey of what has been done in the last few years and to mention some of the investigations the author has made and is making in an attempt to develop more use of plastics in the industry. Some of the plastics used on the mines have taken their place in the industry in the same manner that they are used in everyday life while others have been introduced because there has been a need for them. New uses and applications are being developed and these are the ones that are most interesting. The plastic that is specially developed to give the maximum benefit and not the one that is a modification of some other everyday product is the next development in the field. Many manufacturers are keen to promote such investigation but are not aware of the problems the mines wish to solve and therefore it is only through management itself that this development can be carried out. This note deals with plastic material under three headings: (a) Plastic as the superior material, and briefly describes how plastic has replaced a few major items which are better when made from plastic. (b) Plastics of necessity, being a short summary of how plastics had to be introduced because of laws and conditions making it a necessity. (c) Development of new ideas, being briefly some of the ideas being developed overseas and some of the ideas being tried by the author. Plastic items in common use such as in housing, electric cables, laboratory equipment, awnings, nylon bearings, locomotive brake linings, etc. being well known are not discussed. PLASTIC AS THE SUPERIOR MATERIAL Plastic belting underground Following a fire in a belt road in England resulting in the deaths of many workers, and subsequently a fire accompanied by fatalities in a belt road in a mine in this country, a law was introduced which states that only flameproof belting is to be used underground. This ruling forced the mines to use P.V.A. belting as no other was available. This belting has non-inflammable characteristics that are superior to rubber. Due to the high tension on long-distance belts used today the need for stronger belting material called for something better than cotton and the answer to this was nylon. Nylon also has the ability to withstand dry-rot which reduces the life of a belt very quickly.

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

By M. M. Neale

The pottery department has been aptly described as the "heart of the zinc plant," md every operator of a horizontal-retort plant is acquainted with the fact that good retort practice is the keystone of the smelting process. Since retorts and condensers are clay products, it is obvious that improvements in other branches of the ceramic industry should be observed for possible adoption in the pottery process for zinc smelting. Deaeration of clay bodies is one of the improvements that have become fully, established in many brick and pottery plants. Our investigation of a number of these installations always yielded the same answer—improved practice. Improvement in workability, elimination of laminations, less porosity, greater wet and dry strength, were among the claims put forth for this process. All of these features are exceedingly desirable characteristics in the manufacture of a zinc retort. A preliminary test, which involved truck transportation of deaired slugs over a relatively long distance, did show the value of many of these characteristics in forming the retort. Results from the standpoint of , longer retort life in the smelting furnace were not outstanding. The idea lay dormant for several years but was revived again in 1940, when it was decided to make whatever changes were necessary in the equipment for pottery manufacture to fully demonstrate the process. A number of the manu- facturers of machinery for clay work were asked to submit proposals, and the plan finally adopted was extremely simple and economical. Machine FOR DeaeRRATING Selection of the ''Straight-line'' principle for conversion of the "Wettengel" pug mill to a ''vacuum-extrusion" machine preserved some usable parts of the original equipment, such as the drive mechanism, and main shaft. The converted machine consists of a feed hopper, a compression and shredding zone, a vacuum chamber, and an extrusion barrel, as shown in Fig. I. In operation the clay mix travels from the feed hopper into the compression zone, where it is compressed and finally forced around the tapered cone into the vacuum chamber. As it enters this chamber the clay body is shredded into thin plates, for exFosure to the vacuum. The shredder consists of a hub mounted on the main shaft, to which are bolted segmental sections, each of which carries shredder knives. The compression zone and extrusion barrel function as seals for the vacuum chamber and the shredded clay mix is agitated thoroughly during its exposure to the vacuum. A vacuum pump, equipped with a 3-hp. motor, is attached to this chamber, and maintains 25 to 26 in. vacuum during operation of the mill. Changes in Practice Prior to the adoption of the deaeration process, our standard pottery practice called for double mixing in the combination 7

Jan 1, 1944

By L. Guttman

LESTER GUTTMAN* The question of whether classical thermodynamics alone imposes any lower limit to solid solubilities was raised during a discussion among various members of the Institute for the Study of Metals. Although our conclusions are not new,1 they may be worth reiterating, since confusion on this subject seems to persist. In a binary system (A,B), the conditions for equilibrium, at constant pressure and temperature, between a solid solution and a liquid solution are µAs = µAl [la] µBs = µbl [lb] Here µ denotes the chemical potential either of component A or B, as shown by the subscripts, and the superscripts s and l refer to the solid and liquid solutions, respectively. These two conditions are just sufficient to determine the compositions of both phases. Suppose, however, that the solid phase is found experimentally not to contain any of component B; then we cannot evaluate µbs, which is defined by Here nAs and nBs are the number of mols of A and B, respectively, in the solid, whose free energy is Fs. Eq lb cannot be used, but it is no longer needed: we stated at the outset that the solid has the composition "pure A," and only the liquid composition need now be determined, from Eq la. All the equilibrium properties of the system can be derived from Eq la rigorously and simply. Hence there is no purely thermodynamic reason to exclude phase diagrams which show precisely zero solid solubility. Marsh2 has objected to such diagrams as implying that even the transformation of pure A begins at the eutectic temperature. In any case, the user of the diagram must have a certain minimum knowledge of how to interpret it, and it would seem simpler to remember the general rule that eutectic temperatures have no significance for pure components, rather than to show, say, by broken lines, on a scale which will often be exaggerated, a hypothetical solid-solubility about which we know only that it is less than a certain amount. The case of an intermetallic compound in equilibrium with a binary liquid solution does not require a separate treatment since nothing in the foregoing was dependent on the nature of the components. Therefore, thermodynamics alone does not exclude the possibility that (intermetallic) compounds may exist with compositions always precisely those given by their chemical formulas. With the aid of extra-thermodynamic methods, one may conclude that the solubility of one solid in another is never exactly zero. On the other hand, one would generally expect that the solubility will be small unless the components resemble one another (as do the metals), or form weakly-bound crystals. Therefore, it is useful to know that when there is no direct evidence for solid-solubility, one may neglect it without violating thermodynamic principles.

Jan 1, 1950

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003