Search Documents

By Walter R. Hibbard

ALTHOUGH extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110), [III] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampon5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr s in a standard mercurous nitrate test. Edmunds 12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wassermann reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. PREPARATION OF SPECIMENS Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5,10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. DETERMINATION OF POLE FIGURES A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pct nitric acid to 0.0015 in. thickness and (III) pole figures were determined using copper K-alpha radiation in the manner described by Brick.1 The three general types of pole figures

Jan 1, 1947

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.' Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

The production of harmful pollutants from coal mines and/or from coal and associated strata has been a recognizable fact in the United States for over two hundred and seventy years. In 1698, Gabriel Thomas observed(l) that the colored water flowing from streams in this country was similar to that which flowed from the coal mines in Wales. Hence, water pollutants such as acid were being produced before any known coal mines were operating in this country. The coal mining industry has contributed to the increase of pollution by exposing large amounts of sulfide materials that enable the reaction of water, oxygen and sulfur containing materials to form acid. A map of the United States coal fields can be seen on Figure 1. The anthracite regions of Pennsylvania, although small when compared to the total reserves, have produced some of the country's major water problems. The map indicates the extent of bituminous reserves of the Appalachian and midwest regions. Also evident are the bituminous, subbituminous and lignite coal reserves in the west which have recently come into greater demand. Acid mine pollution is encountered in numerous states, but the major problem is found in the Ohio, Susquehanna, and Potomac River basins.(2) Most coal beds contain some sulfur which may be in the inorganic, sulfate, or sulfide form, and thus have the potential to produce sulfuric acid. However, much of the strata that overlays the coal beds also contains acid neutralizing materials. Therefore, the amount of acid produced depends upon the amount of both acid and alkali materials that dissolve in the water in any given mine. The common sources of sulfurous material in the seam or surrounding rock are generally called sulfur balls or "nigger heads" by the miners. Sulfur balls that have been observed(3) seem to be equally divided between those containing sulphuritic iron capable of producing sulfuric acid upon oxidation and those that are primarily calcium carbonate. It has been observed in many instances that two types of water, acid and alkaline, are being produced in the same mine. A study of the geological strata and a survey of subsidence, faults and sulfur balls will usually give some indication of why this happens. The reaction of pyrite (FeS2) with oxygen and water to form ferrous sulfate (FeSO4) and sulfuric acid (H2SO4) by a series of complex chemical interactions is well documented but not well understood.(4,5) However, it is well known that the reactions to form the acid cannot occur unless all three constituents are present. Since pyrite is inherent in most coal seams and air is needed to sustain the miner, the most logical answer is to eliminate water infiltration into the mine, or to remove it from the mine before acids can form.

Jan 1, 1970

By W. A. Koehler, M. E. Hinkle

INTRODUCTION THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: I. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of fer¬rous (iron) sulphate and some sulphuric acid. 2. The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages nor¬mally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio¬bacillus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not yet been established. Apparently it does not promote the oxida¬tion of ferrous iron compounds in mine, drainage to the ferric state. The second organism has not been identi¬fied by name but is described as "Gram negative, non-spore-forming rods approxi¬mately 0.4 micron wide by o.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur com¬pounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced percentage of oxygen and increased percentage of carbon dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. ACID COAL MINE DRAINAGE Acid coal mine drainage has been the concern of coal mine operators, industrial¬ists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1948

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By Arthur F. Taggart

THIS paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. CAPACITY Operators know that the tonnage of rock that can be put through a particular crusher in a given time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: TR = TR80KK'K" [I] in which TR, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R50 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific-gravity range-2.5 to 2.7-T should be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppard' has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about I.5: I: 0.6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:0.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for -150 + 200-mesh pyrite to be I.4: I : 0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value I.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciable tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 8o per cent of the feed, divided by the aperture that would pass S0 per cent of the product. It is best determined from screen tests.

Jan 1, 1941

By O. Schaaber

THE existence of isothermal martensite without the presence of the athermal form thus far has been established only in a 6 pct Mn, 0.6 pct C steel' and a 23 pct Ni, 3.5 pct Mn-Fe alloy.' " Theoretical calculations, moreover, predict this phenomenon to be observable only within narrow composition limits.' In all other steels, it is generally considered that martensite inevitably forms upon cooling below the M, temperature. Even the possibility of isothermal martensite transformation has been questioned for the common steels, although Averbach and Cohen" showed that martensite formation does not stop when the cooling is arrested and that as much as 5 pct retained austenite may transform isothermally to martensite at room temperature. This note presents some observations made on a number of low alloy steels by dilatometric and inductive measurement of isothermal austenite transformation at various temperatures close to the Ms. In the dilatometer studies reported previously, austenitized specimens were immersed in a salt bath maintained at proper temperature and immediately inserted into the dilatometera8' already at thermal equilibrium with the bath. The dilation was read on a dial gage divided into 0.001 mm intervals. Induction measurements were made with a separate excitation source and a test coil, sealed together in a salt-tight case. The increase in the induced voltage caused by the transformation products was recorded at a paper speed of 4 mm per sec. The steels studied are listed in Table I. Specimens prepared from steels 1 and 2 were in the form of hollow cylinders 60 mm long, 10 mm ID, 14 to 16 mm OD, while specimens of steels 3 and 4 were in the form of notched-bar impact test specimens, DVM type. Specimens of steel 5 were in the form of strip, 7x0.3 mm. In the bainitic range, curves representing the amount of transformation vs log time have a single step appearance, as is shown by the curve of isothermal transformation at 320°C in Fig. 1.Y ransformation proceeds in accordance with the Austin-Rickett equationo P -----------= k t" 100-P where P is the percentage of transformed austenite, t is time, and k and n are constants. Near the M, temperature, however, complex curves having two steps are observed. As shown in a previous papera for steel 3 isothermally transformed at 245"C, such complex curves can be separated into two separate transformations or reactions each following the Austin-Rickett equation. The values of n in the equation for a number of such two-step transformations are listed in Table 11 for steel 1. At transformation temperatures of 250" and 235"C, evidence of a second transformation is very

Jan 1, 1956

THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enormous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engineers, superintendents, and' others, in mastering &he problems which are constantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal-liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects : 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the periodical publication of essays or papers, communicated to such societies by their members. I t must be evident to all practical men that the interchange of the varied experience of those engaged in such occupation in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centers, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. I t is proposed that a meeting of those sympathizing with the object above mentioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

By E. H. Crabtree

THE heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. 1, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. 1, 1946, to represent the ferrosilicon medium. During the first of 'these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. FLOWSHEET The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through 11/2-in. and wet-screening out the minus 3/16in. portion. The minus 1 1/2 plus 3/16in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone .concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. HEAVY-MEDIA PLANT The heavy-media cone plant treating the minus 1 ½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig 1.

Jan 1, 1947

The use of scrapers in mining and earthmoving operations is not new; in fact they are one of the earliest methods of bulk earthmoving. A single machine, which can load, haul, and dump material with a minimum of ancillary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. Maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancillary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

By E. R. Gibson

It is quite generally conceded that the coal mining industry is among the most progressive in the adoption of modern and efficient equipment and mining methods, but most woefully antiquated in many respects in the matter of systematic accounting. The cause of this condition is problematical, but is usually thought to be due to false economy. We realize that those who do not understand accounts, or like accounting, are inclined to be disdainful of accounts and statistics, and to under-estimate the benefits derived from the expense and labor involved in proper accounting. The business that is run without a proper accounting system is subject to haphazard financing and courts disaster. Furthermore, the operator who disposes of his product without due regard to the requirements of the industry as a whole, as reflected in the cost of doing business, is an unfair competitor. No one will deny that the possible production of coal in the United States is much in excess of the demand. While it is true there is an occasional shortage in certain localities, it is due to temporary abnormal conditions which are overcome in a short period of time, when the mines are again obliged to take idle time, and herein lies the danger, not alone to the operator who neglects to keep informed as to operating costs; but to his competitor as well. While physical conditions and operating methods differ materially, accounting methods must likewise differ in some respects, but irrespective of how the result may be obtained, a true statement of cost is absolutely essential. Daily cost statements may be preferred by some, but have proven unsatisfactory, generally speaking, because of variation in production as well as in both labor and material expense from day to day; therefore, we will confine our attention to a monthly cost statement. To be most effective, operating cost statements should be prepared and submitted to the officers as soon after the close of the month's busi¬ness as possible, to enable them to remedy any defects in the operations that might be discovered by an analysis thereof. Opinions differ materially with respect to the most efficient method of compiling and the distribution of labor and material. The writer believes that a time book which provides space in which to enter the number of hours worked each day of the month by each employe, together with distribution thereof, is the most accurate, simple and complete. This record will show the service performed by an employe each day of the month and the account to which same is properly chargeable. This, of course, refers only to the employe working by the-day or month. While there can be but little said concerning the compiling and distribution of miners' wages, as the weighman's bulletin used almost

Jan 1, 1921

By M. W. Dumais, E. P. Abrahamson

In a paper by Abrahamson and Alexander concerning a series of correlations between electronic structure and property changes, it was hypothesized that each solute atom in a dilute solution had a characteristic volume of solvent atoms over which some form of electronic interaction occurred. From this description it is possible to picture the solute atoms as occurring in an ordered array for the most efficient arrangement. A recent review article2 has shown that some form of anomaly exists for a whole series of properties when dilute additions of tungsten are made to iron, of. Fig. 1. Any mechanism to fit one property must also be amenable to mechanisms for the other properties. The possibility of some structural change in this region appears to offer the best hope. The system chosen for investigation was the iron tungsten system. Zone-refined iron with zone-leveled tungsten additions were supplied by Materials Research Corp. as 3/8-in.-diam bars. Transmission electron microscopy was used to study the structure. One-quarter inch specimens of each alloy were cold-rolled to 10-mil sheets, cleaned, punched to electron-microscope specimen-holder size, and annealed in vacuum for 2 hr at 800°C and 2 hr at 700°C followed by a furnace cool. The specimens were attached to a platinum wire and the specimen edge and wire were painted prior to thinning in a solution of 10 pct perchloric acid in glacial acetic acid. It was believed that if ordering were present due to electronic interactions the polishing procedure chosen would provide a simultaneous combination of chemical attack and electropolishing to exhibit the ordered structure. The chemical attack would be expected to penetrate those areas equidistant from the tungsten atoms, while the electropolishing would serve to "plane off" the volumes where the chemical attack had taken place. If one of the ordered tungsten planes were parallel to the specimen face at the edge of the thinned hole, a plate or micalike structure would be expected. A typical result of this polishing is shown in Fig. 2. Here a series of plates can be seen lying one upon the other. In several other specimens the plates parallel to the electron beam have been observed, behaving like slices of bread in a loaf. These edge views coupled with moire patterns indicate that the minimum plate thickness is 37 to 42A. This is equivalent to a concentration of 455 at. ppm of W if a simple cubic superlat-tice exists, or one tungsten atom every twelve iron atoms on the ordered plane. It was further noted that the base iron exhibited no signs of platelike structure. As the concentrations increased above 100 at. ppm W the amount of plate material increased. Among the specimens investigated was that shown

Jan 1, 1967

By Charles Hart

THE-report of the advisory committee to the U. S. Bureau of Mines, on the use of oxygen in metallurgy, brings to the art of steelmaking a radical change in the method of operation of the many processes of this widely diversified industry. When completed, the improvements suggested by the use of oxygen will be far-reaching and revolutionary. As to its effect upon the iron blast furnace, the use of oxygen should be as important as any of the improvements in the art of iron smelting and should take its place beside the German "Hochofen" which was the first attempt to use a shaft for preheating the stock, and beside the hot-blast stove which heated the blast before entering the furnace. The former initially produced molten iron and the latter made unbelievable economies in fuel consumption. It would seem that a discussion of this paper would be best served by following the conclusions on page 17 of the report and analyzing them seriatim. 1. (a) A decrease in costs, due to higher smelting heats is only attainable by taking full advantage of these heat units. This is affected by, adding additional ore to the burden which in turn increases production and yields a larger tonnage upon which to figure costs. These economies appear in decreased cost per ton of iron for coke and limestone consumed, and a proportionate reduction in all items entering the cost above materials. We can take no exception to these. premises. It is a well-known fact that silicon in the iron and sulfur removed" are the result of hearth temperature, other matters remaining constant. To a practical furnaceman the most satisfactory manner of controlling a furnace is by increasing the burden. It is not necessary, therefore, to consider the question of refractories, for this discussion presupposes that the temperatures in the furnaces will be kept practically where they now stand for making the various grades of iron. The same situation obtains in regard to the height of the furnace, which, as intimated, was one of the great strides forward in this art, and its abandonment at this time, is inconceivable. The shaft prepares the stock so that at each succeeding step we have exactly the proper conditions. All the stock entering the furnace is dried and preheated. The limestone is calcined by sensible heat practically at no cost, for this is sensible heat which otherwise would pass from the top with the gases. Under normal conditions, external calcination has been attempted without tangible results. Under normal average furnace operation, limestone requires about 760 B.t.u. for calcination and the loss of sensible

Jan 11, 1924

By H. H. Vogel

THIS paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. CHARACTERISTICS OF THE ORE The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾ mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3A12 (Si04)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to 12 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crystals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3.07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive. FORMER OPERATIONS Mining operations have been carried on for 60 years. Until 1023, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

By Cornelius Kelley

I HAVE been asked to pay a tribute to the mining industry. It is appropriate to this occasion that a word upon this subject should be spoken to this assemblage; but to pay a tribute to the mining indus-try, one that would be worthy of its traditions and its accomplishment and that would outline what it has meant to the economic and social development of this nation, would carry me far beyond what must be the brief confines of this address. I wonder how many there are who have ever paused to reflect how different might have been the current history of the world had it not been that for nearly eighty years a never-interrupted stream of wealth has flowed from the storehouse of treasure in the mines of the West into the commercial and economic life not only of this nation but of the world. Truly it was a historic day that Marshall discovered in the runway at Sutter's mill the glistening particles that proved to be gold. That event was one of the most momentous events in its consequences that ever happened in the history of mankind. Without its occurrence this nation undoubtedly would have grown; it would have reached a position; of economic and social soundness; but certainly it could not have achieved the splendid and immediate results that have become our proudest heritage and established our unrivaled posi-tion in the industrial world. As the primal cause that led to one of the great migratory movements of man it stands alone, unequaled, without any precedent in the annals of history, comparable in its effect on the imagination, on the movement, and on the devlop-ment of a people. Nearly three-quarters of a century had passed since the banners of the Revolution had been furled and a new nation had come into existence. Beyond the boun-daries of the original colonies, and through the passes of the Alleghanies, hardy frontiersmen had cut their way, and the process of establishing what have become -great states in the Valley of the Mississippi was under way. An empire of virgin land beckoned to the home-seekers of the world; but scarcely had its occupation been begun when, true to the instinctive urge that meant the ultimate destiny of the nation, there began the movement to carry the Stars and Stripes westward to the Pacific. Within the boundaries of what was then Mexico, Americans fought and died in the Alamo, and the banner of the Texan had been raised in eager ex-pectancy that its Lone Star might be added to the grow-ing constellation on the American banner.

Jan 5, 1928

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

Previously we reported crushing or grinding crystalline silica results in silica-based free radicals on the particulate surface which can generate hydroxyl radicals in aqueous solution (1). Now we find that freshly ground silica is more cytotoxic to and a more potent activator of alveolar macrophages than similarly sized aged silica. Since the United States Department of Labor estimates that over 1.25 million American workers may be exposed to freshly ground crystalline silica arid nearly 60,000 may be at risk of developing some degree of silica-based occupational lung disease, then this is hardly a trivial problem. Occupations of concern include workers who come in contact with silica including miners of soft and hard minerals, stone quarry workers, glass workers and even millers who stone grind flour. Acute silicosis is manifested by inflammation, alveolar lipo-proteinosis, and the rapid development of respiratory disability that depending on the dose of silica can produce chronic silicosis which takes 20 - 40 years to develop. It is demonstrated by the appearance of concentric hyalinized nodular lesions and progressive development of dyspnea(3). Certainly the free radicals produced on the surface of freshly ground crystalline silica play a most important role in producing the acute and chronic symptoms of silicosis. When respirable-size freshly- ground silica (0.1 -- 5 microns in diameter) enters the deep alveolar spaces in the lung and contacts an aqueous environment, hydroxyl radical are generated and cellular damage is bound to occur. We have found that freshly ground silica can cause lipid peroxidation and lysis of erythrocytes(1). The objective of this investigation was to further elucidate the enhanced toxicity of freshly ground versus aged silica. It can be deduced from the data that not only is freshly ground silica more cytotoxic to alveolar macrophages but it is a more potent stimulant of these phagocytes. However the mere characterization of toxicity is not entirely helpful if there is not a useful means to detoxify the cause of the damage. We have identified an aqueously soluble substance that can be used in high dilution to detoxify the SiO(•) and Si(•) type of free radicals. This is the organosilane known as Prosil 28 (R). We have found that coating of the freshly ground silica can effectively reduce its toxicity. The importance of this observation is that such a coating could be used with water cooled drills. This may partially detoxify silica at the point of generation of the free radical, i.e., the generation of the fresh silica dust itself. Such a coating could be used in great dilution 1:103 or 1:104. The coating would be long lasting, inexpensive and should be non-toxic because of the great dilution.

Jan 1, 1991