Search Documents

By Foster Fraas

INTRODUCTION THAT variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.1 Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or contact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are separated and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a similar problem. PERMISSIBLE MOISTURE The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1947

By D. J. Griffiths

Beyond doubt it is practically impossible to eliminate all chances of accidents from falls. Mother Earth is not going to give up her treasures without some sacrificing on our part. This particular question ranks among the important subjects connected with coal-mining, and has been given less attention as a factor of life- and limb-destroyer than any other cause. The single fatalities which happen create very little attention; nevertheless, when counted up at the end of the year, they outnumber the unfortunate ones that are mowed down by the wholesale by mine explosions. Fire-damp and coal dust were often considered the greatest evils in coal-mining. All records, however, prove this conclusion to be wrong. The second annual report of the Bureau of Mines gives the loss of life caused by falls of coal and roof in 1910 as 1,310, and in 1911 as 1,321. The reports of Pennsylvania mine inspectors for a period of thirty-three years show that 59.38 per cent of all the accidents underground were caused by falls of roof and coal. Also, the Bureau of Mines shows in its last issue on fatalities that accidents from fall of roof and coal killed more men than any other two causes combined, and that they account for more than half of the deaths under- ground. It seems we are getting too accustomed, taking too many things for granted, running too many risks, trusting too much for the best, and preparing too little for the worst. We must remove the cause; then the effects will cease. However, I can see that a better day is here. The main damaging factors underground are falls of roof and sides. A bad roof is tender and lacks the adhesive qualities to sustain its own weight over comparatively small areas. A roof of any character which is frequently penetrated by well-defined slips and cleats, is characterized as a treacherous roof. The carelessness of men has been one of the main causes of most of the accidents in mining as well as in any other industries. Three Grades of Miners Miners can be classified into three distinct grades, to-wit: the experienced and careful, the experienced and reckless, and the inexperienced. The accidents which the first class usually meet with occur through the carelessness of their co-workers, as well as through accidents which are termed unforeseen, such as falling roof between timbers, and between the timbers and the face of the coal. This may have 'previously given evidence of being absolutely sound and safe, but be released by invisible slips or by sudden outburst of occluded gases in large quantities, as we term big blowers or feeders,

Jan 1, 1913

By John E. Sherborne, William M. Newton

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By J. J. Arps, T. G. Roberts

Since the introduction of the relative permeability concept in the middle thirties1,2 various investigators have shown3,10,11,12,15 how the basic equations for the flow of oil and gas through porous media can he utilized to compute the recovery from depletion type or solution gas drive type reservoirs under certain conditions, when the necessary physical data pertaining to the reservoir rock and its reservoir fluids are known. In the study by Muskat and Taylor" in 1945, the effects of viscosity, gas solubility, shrinkage, and the permeability-saturation characteristics of the producing formation on the production histories and the recovery of gas drive reservoirs were analyzed. Each parameter was varied a limited number of times, while keeping the others constant. The work was not carried to the point where the data could be used directly to estimate the primary recovery in those cases where certain rock and fluid characteristics were known or could be assumed. Since the publication of this classic study, the work by Beal in 194616 and Standing in 1952'" has established general correlations of oil viscosity and shrinkage with gas solubility and oil gravity. In addition. a considerable number of relative permeability relationships for different types of reservoir rocks has been published2,5,13,17,19,20. Also, the burden of the numerical work required in the solutions of the differential equation has. during the last few years, been greatly reduced with the availability of modern electronic computing facilities. The purpose of this paper is therefore to present the results of a large number of such recovery computations covering the normal range of variation of the main parameters such as the type of rock, the API gravity of the oil, and the amount of gas in solution. As is to be expected, the ultimate recovery is found to increase with the oil gravity. except for the higher solution gas-oil ratios. Within the normal range of solubilities, the ultimate recovery generally appears to decrease with the amount of gas in solution for the higher oil gravities, and to show a slight increase for the lower oil gravities. Intermediate oil gravities seem to fall between the two trends. The type of reservoir rock, as identified by its relative permeability relationship, appears to have a very pronounced effect on the ultimate recovery. In general, sands and sandstones show higher recoveries than limestones and dolomites, although certain intergranular limestones seem to show a higher theoretical recovery than unconsolidated sand. The recovery from sands and sandstones generally decreases with increasing cementation and consolidation, while the recoveries from limestones and dolomites are highest for the intergranular type and lowest for the fracture type porosity.

Jan 1, 1956

By J. E. Hilliard

It is proposed that shape anisotropy in the internal structure of materials be defined by distribution functions which specify what fraction of the total line length or boundary area lies in a given direction. Methods are descriibed for determinirg these distribution functions from measurements on sections through an opaque material. New derivations, that have certain advanifages over those given previously, are Provided for well-known expressions used in estinzating the total density of lineal or areal features. INCREASING attention is being given to the quantitative description of imicrostructures in metals and other materials. This interest stems from the recognition that the structure often provides a convenient half-way point between the properties on the one hand and the processing variables on the other. Such cross correlations become increasingly desirable as materials become more complex and the demands on them more stringent. One of the principal aims in structure analysis is therefore to find parameters that are readily measurable and specific enough to be correlated with other properties of the material. Certain properties, such as magnetic and mechani cal behavior, are strongly influenced by structural anisotropies; in order to relate such properties to the structure it is obviously necessary to have means of specifying and measuring the type and degree of anisotropy. For the determination of preferred orientations in crystal structure, X-ray diffraction methods are available and are widely used, but scant attention has been given to the estimation of anisotropy in the shape of grains and particles. It is the latter problem that will be considered in this paper. It is evident that shape anisotropy can be describe in terms of preferred orientations of lineal and area elements of the structure. It will be shown that these preferred orientations can, in turn, be specified by distribution functions that define what fraction of the total line length or boundary area lies in a given direction. Methods will be given for determining the distribution functions from measurements on sections through the structure. Even when the orientation distributions are of no interest per se, they still have an important bearing on the measurement of the total line length or boundary area by means of an intercept analysis. The treatment in terms of orientation distribution functions leads to new derivations, that have certain advantages of those given previously, for the well-known expressions used in estimating the total density of lineal or areal features. The treatment is divided into two main sections. The first deals with the orientation distribution of a two-dimensional array of lineal features such as occurs in the projected image of dislocations in electron transmission microscopy. The other section treats the estimation of the distribution of lineal and areal features dispersed in three dimensions.

Jan 1, 1962

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

Discussion of the paper of C. W. WASHBURNE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93,. September, 1914, pp. 2365 to 2378. ROSWELL H. JOHNSON, Pittsburgh, Pa.-It seems to me rather important to bear in mind one thing which is sometimes lost sight of, that the marine sedimentary rocks are laid down in water. We have to start with an initial charge of water. That being so, and the surface tension between the water and the -oil being as slight as it is, as referred to by Mr. Washburne,. the phenomena of capillarity are bound to be most important as between the liquid surface and the gas surface. So far as the liquid-gas surface is concerned, capillarity, in my opinion, is of the utmost importance, and it seems to me this paper of Mr. Washburne's is of great value to us for that reason. Starting out as we have, with our attention concentrated upon gravitational sorting, we have had to wait for the discussion of movement furnished by Munn, and this discussion of capillarity by Washburne, for a more balanced view of the situation. It seems to me that in the accumulation of oil and gas we have a problem of the interworking of gravitational sorting, capillarity, viscosity, immiscibility, and movement. All five things seem to me to be important. I would have expected Mr. Washburne to have given a fuller treatment of the relation of movement to capillarity. In my own experiments I find that gravitation and capillarity alone seem remarkably impotent when everything is at rest, but if I furnish a little movement, gravitation and capillarity step in and accomplish a great many results that one would not expect. Take a horizontal tube and fill a portion at the middle with an ordinary sand saturated with oil, and then put water and sand in each end, and the tube may remain at rest a very long time without that oil distributing itself along the top of the tube. But with a little motion that oil will gradually work up to the upper side. So gravitation and capillarity alone are rather impotent unless they get this element of movement. It would not be necessary to have very extensive movement, but some degree of movement is essential. Now if natural gas, in addition to the method of origin by the action of bacteria on organic matter in mud, may also arise by pressure at great depth, as the overburden is added, a great deal of motion may result. I think more motion is produced in this way than by the descent of meteoric waters.

Jan 4, 1915

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.', n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " '.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.',' Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a'=-n;s/= nD,(qo);"; and b' = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

By Bonn J. Macy, David A. Gulley, William A. Vogely

INTRODUCTION Some of the most famous and graphic environmental incidents have arisen from mineral extraction, including oil spills, the Reserve Mining asbestos tailings case, Kaiparowitts surface mining and coal combustion, and other environmental causes celebre. The remote location of much of the mining industry to some extent reduces the human health hazards from pollution, but often times the pristine locale in which mining is conducted provides a sharp contrast to the impacting industry. This prompts questions as to what the research literature says about the true costs and benefits of environmental compliance. We survey the state of this knowledge. Where possible, we discuss studies focused on mining and related industries, such as primary metals production. In many cases, how- ever, the studies pertain to the economy as a whole. For present purposes, the mining industry is defined as companies engaged in the production and refinement of minerals, including metals, fuels, and nonmetallics (e.g., phosphate, sand and gravel). There are several stages in mining, with environmental effects occuring at every stage. The exploration stage comprises the period from initial prospecting to the point where the deposit has been located and delineated in sufficient detail to permit development decisions to be made. Geophysical and geochemical surveys, diamond drilling programs, and exploratory stripping and excavation are activities that may be employed during this stage. Some forms of prospecting are relatively benign, al- though even airborne surveys and motor vehicles generate noise pollution. Roads and the passage of vehicles and equipment affect land surfaces and vegetation, and attract heavier backcountry use. Clearings, stream crossings, and borrow pits can lead to increased erosion and sedimentation of streams. Geological survey grids disrupt vegetation and appearance. Moreover, prospecting can involve the excavation and stripping of overburden, resulting in soil and vegetation disruption as well as in- creased sedimentation of streams and lakes. The effects of exploration are often temporary, and frequently less severe than for other activities. Nevertheless, exploration-related impacts vary with the intensity and type of exploration effort, and can be significant. During the development stage of mining, shafts are sunk, pits excavated, buildings erected, and transportation facilities established. Dust, noise, and other socioeconomic and environmental impacts are generated by the relatively large and sudden influx of people, equipment, and activity. Surface disturbance and solid waste are generated by development, and liquid wastes form when mines are dewatered. The extraction phase is associated with a variety of environmental impacts. These impacts may differ for surface and underground mines. In surface mining, surface disturbance is obviously a major consequence. Piles of overburden and waste accumulation mar land surfaces. Wind and water erosion tend to spread the dis-

Jan 1, 1985

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By Tracy L. Atherton

The mapping of slant-hole oil fields is complicated by the fact that relationships between wells are subject to variations in three dimensions and are not readily adaptable to representation on a plane surface. Formalized perspectives usually expand into an undecipherable maze of lines and peg models with the necessary supporting dividers serve only to awe the beholder with their perplexity. The usual compromise arrived at is a plotting of the projection of the courses of all of the wells in the field onto a horizontal plane (Fig. I). These complicated plots, when used in conjunction with the individual vertical projections of the wells, heretofore have been the most practical foundation for the study of general field problems. This method has many shortcomings, however, which arc not found in the recently developed straight-hole equivalent projec-tion method. The new method supplies a series of maps similar to the type now in common use in straight-hole fields. It is remarkably simple to use and supplies a ready check on clearances between wells. Perhaps the method can best be understood if the steps that led to its development are described. Common practice of oil-well surveyors is to supply the owner with a tabling of the survey and a plan view plotted against the true meridian. If a vertical projection is plotted, it is usually plotted separately and shows vertical depths against the projection of the stations along a section line joining the top and bottom of the hole on the plan view. A more practical method would be to plot the section line of the plan parallel to the abscissa of the vertical projection (Fig. 2). If this is done, any line parallel to the "base line1' will pass through the points on each projection that represent a single point in the hole. Another very useful graph, which the well surveyor could provide, would be plotting of vertical depths against measured depths. Fig. 3 illustrates the next step facilitated by this form of plotting. The lines designated "well A" represent the proposed course of a hole to be drilled. Superimposed on the drawing, in its proper relative position, is the plan view and a portion of the vertical projection of a present producer, well B." From an inspection of the plan view we arrive at the correct conclusion that the only indicated possibility of collision is at the point of crossing of the wells on the plan view. Referring to the vertical projection, note that the vertical depths of stations on B, in the vicinity of the crossing, are plotted on the same plane of projection as A. The clearance is the indicated distance between the two vertical sections measured along the parallel to the "base line," which passes through the point of intersection of the plan view. Repeat this process for the other wells crossing the proposed course of A on the plan view and you have a preliminary check of clearance for the proposed course. A similar comparison of crossings on the vertical projections of all >

Jan 1, 1941

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By John T. Galey

The outstanding developments of the year in southwestern Pennsylvania were the establishment of the Summit Fayette County gas pool and the gas pool in Nicholson township, Fayette County, and Monongahela township, Greene County, as major producing areas, and the indication of four new shallow gas pools. Curtailment of drilling for shallow gas is expected to follow order M68 of the Office of Production Management. Gas completions were approximately 70 per cent higher, oil completions nearly 25 per cent lower, dry holes were unchanged and drilling wells as of Dec. 31, 1941, nearly loo per cent higher than last year. Shallow Development Oil.—Outside Butler County, only 11 producers were drilled, with a total initial of 221 bbl. The best of these was in a portion of Gilmore township, Greene County, which ordinarily produces gas. This well flowed 77 bbl. in 11 hr., along with about one million cubic feet of gas from the Fourth (U.Dev.) sand. Washington County had a 10.20 and a 25-bbl. well in Morris township and a 20-bbl. well in South Franklin township. These were all in the Fifth Sand. The price of oil to Jan. 27 was $1.80 per barrel, when a 15¢ increase was made. This was followed by a raise of 20¢ on Apr. 23, 15¢ on May 21, 20¢ on June 18 and 25¢ on Aug. 14. The last increase was canceled on Aug. 23 by the Office of Price Administration, which pegged southwestern Pennsylvania crude at $2.40 per barrel. Gas.—An almost doubled initial production of natural gas is the result of the large increase in number of wells drilled. The outstanding discovery of the year was in the vicinity of Armbrust, Hempfield township, Westmoreland County, where a well drilled to what at first was considered the Bayard sand, but what is now known to be the Fifth (U.Dev.) sand, at 2100 ft. found nearly 5 million cu. ft. of gas. Since this completion 14 wells have been finished, only one of which was dry, giving a combined total open flow of approximately 15 million cu. ft. The sand is 35 to 40 ft. thick and the saturation extends through most of that thickness. Rock pressure, which is 1040 lb. per sq. in., is abnormally high. An area of only about one square mile has been proven but some of the 24 new wells drilling as of Dec. 31 will no doubt extend it considerably. This development has taken place in an area heretofore considered to have had little prospect. There were three good wells in other parts of Westmoreland County. One well in Franklin township, which had 12 million cu. ft, of gas in the Fifth sand, was entirely surrounded by dry holes but is still pro- . ducing at a high rate. In Bell township a 1.6 million cu. ft. well was found in the Speechley (U.Dev.) sand and in Washington township the same sand produced 2.7 million cu. ft. with shut-in pressure of 970 Ib. at 2820 ft. This well is offset by two dry holes and one well with a capacity of only 10 M cubic feet.

Jan 1, 1942

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By M. G. Cheney

Careful estimates indicate that during 1942 new discoveries and extensions in West Central Texas added oil reserves slightly in excess of the eight million barrels produced. Drilling activity fell 40 per cent below 1941 and 82 per cent below the normal drilling activity of the late 1920's. Total production for the district continued its downward trend, now being less than % of the 42.7 million barrels peak in 1921. Rapid revival of activity is not probable under existing conditions, as costs of discovery, development and operations on the average probably now exceed current market price for the oil, the latter having remained constant since the spring of I941. Costs have advanced materially since the third quarter of 1941, when reports to the Tariff Commission indicated a margin of profit of 13.3 per barrel. Physical as well as economic conditions are holding back the amount of drilling in this district. The lenticular sands are not suited to 40-acre spacing regulations. There is no surplus of experienced oil-field labor. To reduce costs, much second-hand material is used for all except the deeper wells.. Price controls have retarded movement of used equipment by prescribing maximum prices that arc too low for the better grade materizl, thus making , owners reluctant to sell. On the other hand, buyers are unwilling to pay ceiling prices asked by sellers for poor material. Seventeen new oil fields and five new gas fields were found during 1942. Extensions and deeper 'drilling brought favorable results in eight older fields. The most significant new developments appear to have been in Coleman, Jones, Shackelford and Taylor Counties. A 5800-ft. completion in Wise County brought this county into the producing column for the first time. None of these new discoveries can he rated above one million barrel reserve on the basis of present development. Probably the most important development was discovery of a deeper pay (Gunsight lime) in the Wimberly field of Jones County, which shows promise of producing over an area of about 1000 acres. Jones and Shackelford Counties still lead the district in total annual production. Discovery of the Reddin pool, north central Taylor County, is credited to geochemical methods, making one success out of five or more wildcats based on such methods. Geophysical surveying increased decidedly during 1942 and returns from these studies are expected during coming years. Most of the wildcatting in the district is still based on surface and subsurface geological structural mapping, study of log data as to distribution of prospective producing reservoirs, and drilling in proximity to previous showings of oil and gas. Geological debate continues as to the proper correlation of the 100 to 300 ft. of gray lime that has produced more than 100 million barrels in the Parks, Brecken-ridge, Curry, Eliasville, Ibex, Pioneer and other important fields of this district. Fossils indicate that this limestone is younger than the Atoka beds of Oklahoma. On a structural basis most geologists include this formation with the Bend but a number of paleontologists believe it is more properly classified with the Strawn.

Jan 1, 1943

By M. M. Slotnick

It was once aptly said that a sign of approaching senility is ceasing work on a subject and beginning to talk about it. Perhaps that explains why, after many Years in which Part of my duties has been the training of college men in various branches of petroleum exploration geophysics, I have now begun to talk about it. In making an outline of what I believe ought to be discussed under the general heading of the title, I found it almost impossible to subdivide the ideas into an ordered set of discrete subjects. Rather, the pertinent remarks seemed to interlock almost everywhere. The consequence is that it will be necessary to start with the conclusions and then try to justify them by jumping back and forth. However, based on the types of men with whom I have had to deal, the subject naturally divides itself into two parts. In the first part, I should like to deal with the case of those undergraduates whose natural bent is toward the physical sciences and who may decide to enter the geophysical fold as a career. The other part will deal with those many men, geologists and engineers for the most part, who have drifted into exploration geophysics by one means or another, and whom it is necessary to train for geophysical work while they are occupied in their routine jobs. Here it may be in point to remark that most men in exploration geophysics at Present have been developed from precisely the latter group, and that the problem of training here is of great importance even though, in this paper, it will perforce occupy the secondary place. Training oF a Geophysicist The outstanding reason for the perplexing problem on the training of a geophysi-cist is that ideas differ on the answer to the question: "what is a geophysicistp" ln any of the scientific "specialties," like physics, for example, it is relatively simple to pigeonhole a man as being qualified to call himself a physicist. That appellation applied to an individual does not mean that he has mastered only the branches of intellectual endeavor usually associated under the broad name of "physics." we expect him also to have a more than mere acquaintance with mathematics and chemist~ and some understanding of most of the other sciences. But note this important point—we expect our physicist, whom we have chosen as an example, to be intelligently trained so that, if necessary, he can and will know how and where he can get the proper information on a subject in which he is not a specialist; he will know how to absorb that information and turn it to his uses. It seems to me that this is the outstanding characteristic of a man who can truly call himself a scientist: that he is a specialist in one of the broad branches of science in that he has enough training and discipline in the scientific approach so that, when called upon to do so, he can inteugently absorb knowledge from another bordering science (and all sciences not only border upon one another to some extent, but more often, overlap One another), and

Jan 1, 1946

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946