Search Documents

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood&apos;s recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By L. D. Clark, S. S. Saluja

A physical law, governing the rupture of rock by confined explosive charge correspondent to current expressions for determining weight of charge to rupture rock burden, W, was developed in the form Q = cVw3 by two early investigators performing unique experiments with ice. The coefficient C, is found by trial blast. Recent physical tests conducted with rock, synthetic materials and ice to establish the validity of the theory on which it and other related formulae are based indicated: (a) that failure under hydrodynamic impact pressure is by tension rather than shear as was assumed; (b) that the fundamental law of mechanics, enabling the determination of Q = cvw3, modified to the form P = R x Sa x Wb is valid when low velocity explosives are used; (c) that rock breakage under the action of low velocity explosives is entirely due to explosion gas pressure, as was believed; (d) that under the action of high velocity explosive it is due to the joint effects of scabbing and gas pressure; and that further possible modification could make the above equation also applicable to these joint mechanisms. shape could be easily frozen and because large loads would not be required. They found: (a) that the not unfamiliar shearing equation for metals was applicable to ice where P = load in lb; S = periphery of pressure surface, in.; W = burden, in.; K = modulus of rupture by shear in lb per in.2; and (b) that "the form of cavity produced by the application of gradual pressure is similar to that obtained by blasting in rock under similar conditions of free face and pressure surface!" This similarity in crater shapes leads to the conclusion that rock would rupture by shear, as did ice, and its behavior under the force of a blast could be governed by such a relationship as P = S x W x K. Three important interrelated empirical expressions were derived and rock, charging and spacing coefficients C,, C, and e were established and substantiated by trial blasts. In checking the accuracy of the main assumptions, duplication of the ice tests, substituting rock, suggested that K is not constant and that P = K x W x S, though valid for ice, does not necessarily hold for homogeneous limestone.&apos; Conclusions from this later work raised questions making continued investigation desirable because such conclusions do not destroy the practical value of the empirical equations or theory. Further study for the establishment of the relationship between load, burden and periphery of the pressure surface and possible application of these to the mechanism of rock blasting was undertaken by the authors of this paper. MECHANICAL TESTING - EXPERIMENTAL PROCEDURE Certain inconsistencies in the results of the aforementioned tests repeated on three types of limestone suggested these inconsistencies be attributed to rock inhomogeneity. It was also suspected that the loading speed, which could not be held uniform, may have contributed. The earlier work with both rock and ice

Jan 1, 1964

By H. H. Kaveler

A summary of the reservoir engineering and related geologic data on the Schuler field, Union County, Arkansas, is presented here in a manner intended to interest both technical and nontechnical readers. The Cotton Valley formation and the Reynolds oolite are oil-productive formations in the Schuler field, but the Jones sand pool, at a depth of 7500 ft., developed with 146 wells on zo-acre spacing, is the reservoir of principal interest. The Jones sand sandstone reservoir is an anticlinal trap typically gas-drive or depletion type in performance. The core analyses from 88 per cent of the wells drilled, together with drilling time and electric-log data, yield an accurate estimate of the "productive" sand thickness and its areal distribution over the pool. Accurate production statistics, monthly reservoir-pressure surveys, and bottom-hole sample analyses when correlated by the "material-balance equation" show unusually good agreement with that principle. Estimates of oil initially in place made by the material-balance method and the sand-volume method are in good agreement at 116 to rzo million barrels. The reservoir-pressure history of the pool reflects the reaction of a reservoir to production, proration and secondary-recovery practices. The cost of the extensive program of reservoir study in the Jones sand pool has been estimated, in order to emphasize the value derived from such an investment through better understanding of a reservoir&apos;s reaction to production practices. Unit operation of 140 of the 146 Jones sand wells made possible an effective unitized gas-injection pressure-maintenance program. Res-ervoir-pressure decline was arrested, natural flow was maintained, and pumping and lease equipment were conserved. An increased ultimate recovery of zo million barrels beyond the estimated 34 million barrels primary recovery is indicated at present. Extension of the Jones sand unit to include the undeveloped Cotton Valley formation will permit additional recovery of otherwise uneconomic reserves of oil through wells no longer required in the Jones sand operations. Introduction The Schuler field comprises approximately 4000 acres in and about sec. 18, T. 18 S., R. 17 W. in west central Union County, Arkansas. Three reservoirs are procluctive of oil and gas: the Cotton Valley formation, the Jones sand, and the Reynolds oolite section of the Smackover limestone. The Jones sand pool is the most important reservoir from an engineering viewpoint. It possesses the traditional and somewhat classic characteristics usually associated with an anticlinal trap. Development and operations have followed the dictates of advanced engineering practices. The pool has attracted attention because of the unusually detailed reservoir data obtained, its interesting production history, and the success of the unitized gas-injection pres-sure-maintenance operation now being carried out. The purpose of this paper is to present a summary of the engineering data relating to the field, with particular reference to the more interesting general applications of

Jan 1, 1944

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.&apos; In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6&apos;7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By C. F. Clausen

"Cement" means binding agent or glue. It is derived from the Latin word "Caementum," the name of a limestone, chips of which were used in mortar more than 2,000 years ago in Italy. During the middle ages "cement" or "cement" generally denoted mortar. Today it means any binding material. The Thomas Register lists nearly 200 classifications for "cement" including automobile cement, household cement, rubber cement, etc. The material most commonly associated with this word, however, is portland cement which, when mixed with water and allowed to hydrate, is a ceramic binding material used to cement aggregates (crushed stone, gravel and sand) together in "concrete," the most universally used building material of today. It is estimated that more tons of concrete are used annually than all other building materials put together including steel, lumber, gypsum, bricks, tiles, aluminum and glass. Its use in foundations, building construction, sanitary work, dams, railroads, and highways, makes it difficult to conceive of modem civilization without concrete. A survey made in October 1955 showed the following uses of portland cement: [Percent Highways20 Nonresidential buildings20 Residential buildings15 Military construction10 Sewer and water works8 Public utilities10 Other (conservation, farm, and maintenance and repair)17 100] As of today, the percentage for highways is probably even higher. Ceramic binding materials have unquestionably been used in construction work for thousands of years. The mortar between the blocks of the great pyramids was calcined gypsum (plaster of paris). The use of calcined and slaked limestone goes back earlier than the Roman Empire. Gypsum, however, is relatively soft, and common lime mortar is not "hydraulic," i.e., it does not harden under water. The Greeks and Romans discovered later that an addition of a finely divided active siliceous material (Santorin earth or Pozzolana) would react with slaked lime to form a stronger, and hydraulic, cement. The Appian Way in Italy, Colosseum, and the great Aqueducts built by the Romans were made with this type cement, and some of these structures are still in existence today. However, not until 1756 did some serious research result in the development of better cements. In that year the English engineer, John Smeaton produced a stronger cement by burning a limestone containing considerable proportions of clayey impurities. Other investigations and improvements were made by Bryan Higgins, Bergmann, Joseph Parker, L. J. Vicat, J. F. John, James Frost, and I. C. Johnson.2 Traditionally, but perhaps unfairly to others, the invention of the prototype of today&apos;s portland cement is credited to the English mason Joseph Aspdin who in 1824 obtained a patent and gave the product its name, because in color the mortar produced from it resembled a natural building stone obtained from the British Isle of Portland. The contributions of Johnson and Aspdin were primarily the important step of preparing a synthetic mixture of lime and clay without depending on raw materials found in nature which might contain such elements in desirable proportions. However, even these early

Jan 1, 1960

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw&apos; 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.&apos; Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.&apos; Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By Richard J. Fruehan

ThE thermodynamic activities of nickel and chromium in liquid Ni-Cr alloys have not been previously reported. There have been several investigations on the solid alloys.1-3 In the present investigation the activity of chromium in liquid Ni-Cr alloys at 1600° C was determined by the use of the following galvanic cell, The use of galvanic cells employing solid oxide electrolytes for determining the activity of metals in solid alloys was first demonstrated by Rapp and Maak4 on Cu-Ni alloys between 700° and 1000°C. Recently Schwerdtfeger5 tested the performance of the ZrO2(CaO) electrolyte at 1600°C and found it satisfactory for oxygen pressures as low as 10"12 atm. He also demonstrated the use of solid oxide electrolytes for determining the activities in liquid metal systems in measuring the activity of manganese in Fe-Mn alloys at 1500°C. Extensive investigations have been carried out in this laboratory, exploring the oxygen partial pressure lower limit at which ZrO2(CaO) electrolyte can be used satisfactorily in oxygen galvanic cells at 1600°C. In a paper to be published at a later date,9 it is demonstrated conclusively that ZrO2(CaO) exhibits insignificant electronic conductivity at oxygen pressures down to about 3 x 10"13 atm which is lower than the oxygen partial pressure in equilibrium with Cr-Cr2O3 at 1600°C. Therefore, the activity of chromium can be related to the measured reversible electromotive force of the cell in the present investigation since no electronic short circulating will occur. Fig. 1 is a schematic diagram of the cell used. The Cr-Cr2O3 electrode was made of equal weights of chromium and Cr2O3 powders which were mixed and packed into a recrystallized alumina crucible. A Pt-wire lead was embedded into the Cr-Cr2O3 compact to insure good contact. A ZrO2(CaO) crucible, supplied by the Zirconium Corp. of America, contained the Ni-Cr melt equilibrated with solid Cr2O3. The ZrO2(CaO) crucible was placed on the Cr-Cr2O3 electrode and additional Cr-Cr2O3 mixture was packed around it. Contact with the Ni-Cr alloy was made with a Cr2O3 tube, which is a weak electronic conductor. A platinum wire lead was attached to the Cr2O3 tube. The galvanic cell was lowered slowly into the hot zone of the furnace tube in order to avoid too large a thermal shock which could break the ZrO2 (CaO) crucible. The furnace was con- tinuously flushed with purified argon during the experiment. The temperature was measured with a Pt-Pt/10 pet Rh thermocouple and maintained at 1600° ± 5°C. The electromotive force was measured with a recording potentiometer. The furnace was turned off when measurements were being made in order to avoid induction effects and the reversibility of the cell was demonstrated in the usual manner. The electromotive force was measured several times over a period of approximately 1 hr. During that period the electromotive force remained constant within ± 3 pet and did not continuously drift in any one direction. After the experiment the alloys were analyzed for chromium in the usual manner. The measured electromotive forces of the cell at 1600°C, (2912°F), are listed in Table I. The activity of chromium, with solid pure chromium as the reference state, (a), was calculated using Eq. [l], , n F E I, n lna RT- U] where E is the measured electromotive force, F is the Faraday constant, and n is equal to 3, the number of equivalents per mole, (nF/RT = 18.59 volts&apos;1 at 1600°C). The resulting activities are listed in Table I. The activity of chromium relative to pure liquid chromium was also calculated. The free energy of fusion of chromium at 1600° C was calculated using

Jan 1, 1969

By Don Suttie, Frank Roybal, John Wright

The Roybal Raise incorporates the simplicity and low cost of a short bald-headed raise while overcoming the usual impediments to driving a high baldheaded raise. The concept provides for speedy excavation and maximizing the use of the excavated opening, using the rock for structural support. The design is simple: two baldheaded raises are driven parallel to one another, interconnected by dogholes about 8 m (25 ft) apart. In this fashion, the raise can be driven safely and efficiently to 60 m (200 ft) or more. When the raise is complete, the excavation requires no timber for support or partitioning. Rather, the rock itself supports the construction. As a test, a two-compartment Roybal Raise was attempted at the Independence mine in the Willow Creek District of Alaska. One side was driven 2 x 2 m (6 x 6 ft), intended for a manway and equipment skip. The other was driven 1.5 x 1.5 m (5 x 5 ft) for a muck compartment. Both sides were driven at a 65° angle from horizontal and 1 x 1 m (4 x 4 ft) dogholes spanned the 4.6-m (15-ft) pillar between the two compartments. After topping out at 50 m (160 ft), the raise was found to meet all expectations of efficiency, low cost, and practical simplicity. Technique Preparing the Roybal Raise for driving involves no elaborate or costly site prep except assembling materials and providing for muck removal. Normally, the raise muck falls directly onto the sill or track and is picked up either by an overshot mucker or a front-end loader. Raise mining proceeds initially by taking up both compartments simultaneously to the first doghole. It progresses by alternating one side as a clear manway for access with the other side, the active side, as a muck compartment (Fig. 1A). This stage proceeds quickly for no mucking or staging is required to cycle the first three rounds. On the fifth round, in addition to the normal raise round, rib holes are winged out toward the adjacent raise, thus starting the dogholes. Finally, as the sixth raise rounds are drilled and shot, the first doghole is also completed from both sides. The second stage commences by establishing one side as a clear manway for access while the other side, used as a muck compartment, is prepared for active mining. Figure 1B illustrates this step in the succession of raising with the active side advancing to the second doghole level. During this stage, services are maintained through the manway side and equipment is stowed in the doghole during blasting. As the active side advances, muck may be allowed to fill the bottom portion of that side since it is unnecessary to clear it for access. The next stage of raising involves cleaning out the former muck compartment and preparing it for use as a manway. At the same time, the former manway is prepared for advance and use as a muck compartment (Fig. 1C). As in the previous step, the same doghole is used for access and equipment storage. The active side advances until the second doghole is completed, at which point equipment and access are moved to the new doghole. From there, the active side is driven past the second doghole 8 m (25 ft) more to the third doghole level. Again, half of the doghole and the next raise round are mined. The fourth stage involves switch ing back the manway side for the muck side (Fig. ID). The new muck side is driven to the third doghole where equipment storage and access are reestablished. From there, the active side is advanced to the fourth doghole. In the same fashion, the raise is advanced to the top, alternating the manway side with the active side, maintaining access through the inactive manway, and storing equipment in the uppermost doghole. The cycle time for driving each compartment, regardless of the raise height, is greatly improved over that for normal bald-headed raises of comparable height. By storing equipment in the upper-

Jan 1, 1984

By R. H. Moore, B. D. Breitenstein

INTRODUCTION The United States Uranium Registry (USUR) tissue program was funded in 1978 by the United States Department of Energy (DOE) through its Human Health and Assessments Division, and registrant enrollment began in 1980. It is operated by Hanford Environmental Health Foundation (HERF), Richland, Washington, with support provided by Pacific Northwest Laboratory (PNL).** The USUR tissue program is the first systematic effort to contact and gain assistance of workers occupationally exposed to uranium and to seek and study uranium deposition in human tissue. This paper describes the program objectives, populations selected for study, procedures for enrolling workers in the program, types of tissue to be studied, and analytical procedures to be used. PROGRAM OBJECTIVES The objectives of the USUR tissue program are to: 1) Determine the distribution and concentration of uranium, if any, in the tissues of occupationally exposed workers. 2) Compare bioassay measurements of exposed individuals with the results of analyses of tissues obtained at autopsy. 3) Seek evidence of histopathologic changes related to any uranium deposition that may be present. 4) Conduct analyses of whole bodies, when available, to obtain more precise data on the uranium burdens, if any, in the body and organs, and especially the distribution in parts of the body, such as the skeleton, that are not usually accessible for sampling. 5) Develop data that will assist in evaluating a) the accuracy of current in-vivo measurement techniques, b) the propriety of existing regulations, and c) the adequacy of current protection programs. SELECTION OF POPULATIONS FOR STUDY Selection of the populations for the USUR tissue program was based on studies of the United States Uranium Registry described elsewhere (0c81). Potential populations for study were quite varied because of occupational exposure to different chemical forms of uranium, different levels and eras of exposure, varying ability to identify populations exposed in the past, and the general interest and cooperativeness of the populations. Nevertheless, certain identifiable populations emerged that were both willing to participate in the study and likely to provide useful information. Among the targeted populations are individuals who were exposed to uranium prior to the existence of modern exposure standards. These individuals are presently being enrolled by the USUR. The reliability of concentration and distribution data and the demonstration of effects are more likely in such individuals than in those who have received less exposure. However, the targeted groups also include individuals who Have been exposed to permissible levels of uranium, and reference employees in uranium plants who have not worked with uranium. The lesser exposures are of immediate interest because of the rarity of heavy exposures under current standards. The sampling of potentially exposed individuals with negative in-vivo measurement results may serve to check the adequacy of in-vivo measurements in the detection of deposition. [ENROLLMENT PROCEDURE] The enrollment of participants follows three patterns. 1) Presently employed workers are enrolled by the cooperative efforts of USUR staff with the medical, industrial relations, and/or health physics personnel of the uranium facility. Volunteers may be enrolled by medical personnel at the time of their physical examination or by health physics personnel at the time of a bioassay or lung counting procedure. Follow-up after initial contacts with currently employed uranium workers is carried out by on-site personnel, but subsequent follow-up is the responsibility of the Registry. 2) Retired workers are contacted by mail, with a covering letter from their former employer supporting the principles of the study but leaving participation in the program on an entirely voluntary basis. 3) An alternate method of enrollment is to obtain a USUR autopsy consent after death from the next of kin. As part of enrollment in the program, permission is requested for access to the individual&apos;s medical and exposure data, and a short occupational history is filled out. The autopsy permission agreement signed by the individual is for an initial period of 5 years; the USUR ordinarily seeks renewal of the agreement upon its expiration. While this agreement provides

Jan 1, 1981

By Eugene McAuliffe

The subject of my few remarks addressed to the Rocky Mountain Coal Mining Institute, "Guessing or Knowing! Which," may perhaps suggest but little to you here today. However, I am sure you will all agree with me when I say that in the conduct of a coal mining operation there should be no choice between guessing and knowing. The value of, and the results to be obtained from this Institute, its meetings and printed transactions, as well as those of other similar educational organizations, depend very largely on the mental attitude of those who constitute, through their pronouncements, the more active portion of the membership. Perhaps the most apt criticism that is now being made of the coal industry is that, to an extent possibly exceeding any other industry of similar magnitude and importance, it depends for its conduct altogether too much on "rule of thumb" and "tradition," rather than on proven practice and actual fact. The records of our coal mining association meetings bear expression of many conflicting opinions, the majority of which are sincerely put forth by those expressing same as representing the facts; the extremes expressed, however, frequently fix the question raised as one yet located in "no man&apos;s land." There are yet too many chances taken we are still "weighing pounds on railroad track scales" and measuring yards with the proverbial "bit of string." The actual expense of conducting any one of the several operations incident to the production of coal is rarely determined, and in many instances the general cost figures, prepared some weeks after the work is complete, are of that sweeping character that very little can be abstracted therefrom. Many coal companies are now making a daily cost sheet, showing the cost of labor and material in detail, as used in the several related operations,, and such is decidedly helpful, particularly to the mine superintendent and his foreman, who, without such, sail an uncharted sea; the auditor&apos;s belated monthly summary rarely ever seen by these men who are held responsible for the labor and material used. I have made reference to this situation as an accentuation of the fact that the coal industry contains more "serious minded, conscientious guessers" than does any other similar industry, although the annual cost of our product runs up well beyond the billion dollar mark, and what is more important, our industry is one that still continues to exact a heavy toll of human life. Now this brings me to the question of safety, the one question that should be, and which is, I know, uppermost in your minds. The coal mining world, engineering and operating, is now well sold on at least two things the theory of using permissible explosives and the elimination of the open light. Furthermore, the industry, particularly that portion which is located in Great Britain and the United States and Canada, are now planning vast extensions of the use of "rock" or "shale dust," both in the form of "dust barriers" and in "direct application" to entries and cross-cuts. This is well; however,, my study of past mine explosions has convinced me that the great majority of such had their very beginning in gas accumulations; frequently originating in restricted areas at the working face, in abandoned worked-out areas, or in some other certain place where ventilation is not, maintained as it should be; and that again leads me to the point where it can again be well said, that there is too much "rule of thumb," too much guessing now being done in regard to the volume of air required, and continuously furnished, in a given entry,, panel, room or area. Just to emphasize this situation, is it not a fact that the majority of mine inspectors express the ventilation conditions as measured by them, in terms of cubic feet per man employed, in each certain split, and does not the mining laws of many states yet demand a minimum of "100 or 150 cubic feet

Jan 1, 1924

By A. T. Aldred

HIS note reports the existence of several new scandium intermetallic compounds of the A2B and AB stoichiometries where the A element is scandium and the B element is from group VIII or IB of the periodic table. Alloys were arc melted from high-purity materials using 2-g charges. Typical lot analyses for the materials used are given in Table I. Chemical analyses were not made on the alloys as there was little or no weight loss on melting. After annealing the specimens for 14 days at 600°C and water quenching, metallographic and X-ray techniques were used to determine the occurrence of the various phases. Table II lists the relevant data for the A2B phases. The Ti2Ni structure,2 has ninety-six atoms in a face-centered cubic cell, whilst the Al2Cu structure is body-centered tetragonal.3 The occurrence and stability of the various A2B type phases in transition metal alloy systems has recently been considered by Nevitt.4 The Ti2 Ni-type phases occur over a relatively narrow range of radius ratios from 1.14-1.26 with A partners mainly from the titanium group and B partners predominantly from the cobalt group. This suggests that both a favorable relative size of the atoms and a favorable electron concentration are necessary conditions for the existence of this structure type. A12Cu-type phases involving Ti group elements as A partners are formed with B partners from the cobalt and nickel groups, predominantly the latter, and have a higher radius ratio (1.27-1.29) than the Ti2Ni-type phases. The occurrence of both Sc2Pd and Sc2Co can be rationalized in terms of these considerations but SczNi is anomalous because of its high radius ratio. The radius ratios are calculated from the Goldschmidt CN12 radii and it might be postulated that the scandium atom is reduced in size in the compound. Unfortunately the apparent atomic size of scandium in the compound cannot be calculated from a knowledge of the structure and lattice dimensions. The crystal structure of the Sc2Au compound could not be identified from the powder diffraction pattern, but it is interesting to note that it is isostructural with a series of A2Au phases where A is a rare earth element.5 Pertinent information concerning the AB phases found in this investigation is given in Table 111. All the phases have the ordered bcc CsCl structure. The occurrence and stability of CsC1-type phases have recently been discussed by Dwight,7 who concludes that the relative sizes of the atoms do not appear to be a controlling factor (the radius ratios of all the known phases vary between 0.985 and 1.439) but that the occurrence of the phase is predominantly dependent on the relative positions of the A and B partners in the periodic table. As a measure of the stability of a given CsCl phase it has been customary to define a lattice contraction on alloying, DAB — dAB, where DAB is the AB interatomic spacing as calculated from the Goldschmidt CN8 radii and dAB is the AB interatomic distance in the compound (= v3/2 ao). Values of the parameter DscB -dScB for the compounds found in this investigation are given in column 5 of Table III and are plotted in Fig. 1. If the lattice contraction does in fact reflect the stability of a phase then Fig. 1 shows two very interesting trends when the position of the B partner in the periodic table is considered. Firstly, within any given group the stability increases in order on going from the first to third long period. Secondly, within any given period the stability increases in order as the B partner is taken from the copper, nickel, and cobalt groups. In the case of the second long period, the lattice contraction reaches a maximum at ScRh and then decreases to ScRu. The same trend could

Jan 1, 1962

By G. K. Manning, M. C. Udy, L. W. Eastwood

Those who have examined beryllium and beryllium-rich alloys under the microscope have noted the results of the difficulties encountered when preparing these materials for examination. Hard constituents are readily chipped and pulled out of the matrix, and the soft ones are easily gouged out or embedded with abrasive or other material. The matrix is easily deformed, which makes it very difficult to remove the effects of scratches. Furthermore, the matrix and some of the constituents are also readily pitted during etching, which makes the structure difficult to develop. The metallographic techniques designed to avoid these difficulties are neither radically new nor necessarily the best possible procedures. They were developed at Battelle to fill immediate requirements as part of a study of the preparation and pouring of beryllium melts as described in a separate paper. A part of the research program on the causes of gas unsoundness in beryllium castings entailed a study of the effects of such gases or gas formers as oxygen or oxides, nitrogen or nitrides, and carbon or carbides. These gases or gas formers, if dissolved in the melt, might be an important factor in the study of unsoundness caused by gas evolution in beryllium. Because it was necessary to be able to distinguish these gases or gas formers, if present as alloy constituents, from metallic phases also present as alloy constituents, a series of alloys was prepared with additions of the various possible metallic and non-metallic constituent formers. It should be emphasized that the constituents referred to as gases or gas formers are important in the study of gases in beryllium only if they form a part of the alloy, that is, if they dissolve in the liquid or solid metal. During the first part of the development of metallographic techniques, the Massachusetts Institute of Technology, unpublished report (TC 3315, Nov., 1945) by Paul Gordon, describing various microconstituents in beryllium, was quite useful. Of particular interest in this report is the confirmation of one of the conclusions drawn from the present investigation, that is, that a distinct oxide phase apparently does not occur in beryllium. The Preparation of Metallographic Specimens GRINDING PROCEDURE The original specimen is either sawed or cut on an abrasive wheel to a convenient size. For best results, the surface to be polished should not be more than about 1/4 in. square, and it is convenient to mount the specimens in bakelite to facilitate handling. Two alternative grinding procedures have been developed. As one alternative, specimens are ground successively on 120-, 240-, and 400-grit, wet-or-dry metallographic discs. The abrasive discs are revolved at 1750 rpm on a conventional pedestal grinder. The coarsest disc (120 grit) is used either wet or dry, and in most instances, it can be eliminated from the procedure. Grinding on the two finer discs (240 and 400 grit) is accompanied by the application of kerosene. The technique consists of holding an oil can, containing kerosene, in one hand and the mounted specimen in the other hand. While the grinding is being done, several drops of kerosene are applied every few seconds close to the center of the disc. Carbon tetrachloride serves at least as well as kerosene as a lubricant; perhaps it is slightly better, but it volatilizes so readily that an additional health hazard is involved. Light oils and water are not satisfactory for the finer grinding operations. The second procedure is perhaps slightly slower than the first and requires a more careful technique, but it eliminates the use of kerosene. The specimen is first ground wet on a 240-grit disc, followed by dry grinding on a 400-grit disc. Finer grinding does not appear to be necessary with either of the two alternative procedures. The pressures used throughout either grinding operation must be extremely light, that is, barely sufficient to hold the specimen in contact with the disc; otherwise, flow and chipping are almost certain to occur. In both procedures, it is essential that the discs be sharp and that they be discarded as they show evidence of becoming dull or loaded. In general, not more than four or five specimens can be ground on a disc before the disc becomes dull enough to warrant discarding it.

Jan 1, 1950

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By Elza Burch

Introduction The feeding to zero concept involves feeding 600 µm x 0 (28 mesh x 0) size raw coal to heavy media (magnetite) cyclones along with the +600 µm (+28 mesh) size coal. Traditional circuits employ desliming or removing the 600 µm x 0 (28 mesh x 0) size fraction and feeding the cyclones +600 µm (+28 mesh) size coal. The feeding to zero concept recirculates 600 µm x 0 (28 mesh x 0) fines in the circuit. At the same time, a portion of the fine material is continuously withdrawn and recovered. This, in turn, prevents a fines buildup. This concept eliminates desliming screens and secondary fines circuitry for recovery of 600 x 150 µm (28 mesh x 100 mesh) coal. The result is a very simple circuit. Feeding to zero at Island Creek Island Creek Corp. was the first involved with the new concept in 1976. The company needed a temporary plant for the 9.5 mm x 0 (0.4 in. x 0) raw coal at its Pond Fork mine, near Madison, WV, while a full-scale plant was being designed and built. At that time, the Childress Corp., of Beckley, WV, became interested in the feeding to zero concept. Island Creek awarded a contract to Childress to build a single cyclone modular plant, incorporating this feeding to zero concept. The plant was erected in three months. The Pond Fork modular plant proved successful in attaining the desired feed rate of about 63.5 t/h (70 stph), while maintaining good separating efficiencies and low magnetite consumption rates. The 9.5 mm x 150 µm (0.4 in. x 100 mesh) clean coal was recovered and the 150 µm x 0 (100 mesh x 0) size was disposed of to waste. The full-scale plant was completed about two years later and the Pond Fork modular plant was moved to Holden, WV. There, it was incorporated into the Holden 29 preparation plant as a separate circuit for cleaning -25 mm (-1 in.) coal. In 1976, a similar plant was installed in Virginia by another company. These two plants are believed to be the first two operational plants in the United States incorporating the feeding to zero concept. Island Creek subsequently contracted with Childress for an identical plant at the Coal Mountain operation in West Virginia. The plant operated for three years before the mine was closed. The unit was then moved to the Spurlock mine near Martin, KY where it continues to operate. The successful operation of the Pond Fork and Coal Mountain plants before and after relocation proved both the performance and moveability of this type of circuit when constructed in a modular fashion. Since the first two plants were built, Island Creek has incorporated the feeding to zero circuit in nine additional plants. A grand total of 33 cyclones have been installed using this concept. One is the Providence mine, near Providence. Providence preparation plant Island Creek contracted with J.O. Lively Corp. of Glen White, WV in July 1978 for the construction of the Providence preparation plant. The plant began operation in February 1979. The construction period was about halved by building the plant with modular design concepts. Prefabricated sections, floors, and sides were brought in as units and then bolted in place. The Providence plant has a good track record of processing coal at a feed rate of 454 kt/h (500 stph). Feed coal to the plant has an average ash content of about 18% and sulfur content of about 4.5%. It contains about 22% refuse. The coal product has an average ash content of about 8% and sulfur content is about 3%. Raw West Kentucky No. 9 seam coal is conveyed from a box cut in the Providence mine to a rotary breaker. The breaker is fitted with 74 mm-diam (3 in.-diam) opening breaker plates. Therefore, it is well suited for removing trash, roof bolts, wood, and pyritic balls that are common in Illinois Basin coal. The -75 mm (-3 in.) coal is conveyed from the rotary breaker to

Jan 8, 1987

By E. C. Ekedahl, R. J. Heath

Introduction Potassium, together with nitrogen and phosphorous, is an essential nutrient required for growth. Since all living things need potash, the major demand for potash - about 95% of the total - is as a fertilizer. Agricultural productivity has increased dramatically in recent times. This increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows then that potash will always be in demand. There is no substitute. Other fertilizers that contain phosphorous (P) and nitrogen (N) are complementary and not competing products. Fireplace ashes (pot-ashes) have a relatively high potassium content. Their value as a fertilizer had been recognized for centuries. But today&apos;s potash industry did not begin until deposits of potassium-rich ore were discovered and exploited in Europe during the 19th century. Canadian potash development Potash in Saskatchewan was first recognized in 1943. It was discovered as a byproduct of an oil exploration program. But it was several years later before the existence of a major commercial deposit was acknowledged, and not until 1951 that the first attempt at development occurred. That attempt was unsuccessful. The shaft flooded and was abandoned. It did, however, demonstrate the need for new technology to penetrate the waterlogged Blairmore layer. This was eventually developed and the first mines were brought into production in the early 1960s. Once the technology was available, and the extent and quality of the potash beds became known, a number of companies proceeded to develop mines. By 1970, seven mines were in operation and three more were nearing completion. Combined, total capacity then was 7.6 Mt/a (8.4 mil¬lion stpy) K20. At that time, world potash consumption was about 15 Mt/a (16.5 million stpy). This increase in supply from Canada produced a large potential surplus that shattered the prevailing balance between supply and demand. Although world demand increased steadily throughout the 1960s and early 1970s, it was several years before world supply and demand were again in balance. Saskatchewan capacity has been expanded a number of times. It now stands at 10.7 Mt/a (11.7 million stpy) K20. Actual production has not approached this figure, however. Two new mines in New Brunswick have recently been built with a combined annual capacity of 1.2 Mt (1.3 million st) K20. Total Canadian capacity of about 12 Mt/a (13 million stpy) now amounts to 30% of world capacity. Central offshore marketing organization Canadian Potash Exports Ltd. (Canpotex) was created in 1970 as the offshore marketing organization for Canadian producers. Canpotex is owned by Saskatchewan producers and is their exclusive marketing organization for offshore business. Each company handles its own sales in Canada and the US, but all sales to other markets are handled through and by Canpotex. The Saskatchewan industry has an ore body of a size and consistency unmatched anywhere in the world. Large efficient mines have production costs that compare favorably with other producing countries. On the minus side, Saskatchewan is remote from most major markets. It therefore needs the ef¬ficiencies that stem from one organization that coordinates all offshore shipments and minimizes distribution costs. Agriculture guides potash market In the period following World War II, potash was a classic growth industry. World demand increased each year from 1945 to early 1970s. Since then, demand has been more erratic. Some years show substantial increases, but are followed by significant declines. For about the last decade, the pattern has been unclear and future demand has become correspondingly difficult to predict. North America and Europe together account for about 40% of the world potash consumption. In both areas, farming is characterized by surplus production, declining crop prices, and expensive government support programs. Under those circumstances, farmers respond by minimizing input costs. Fertilizer is one of the items they reduce. Potash is retained in the soil. It is possible to reduce potash application with no immediate deterioration in crop yield. The lower yields occur only when potash levels are depleted. So, farmers can econo-

Jan 12, 1987

By H. H. Klepfer, M. E. Snyder

UNTIL very recently, the commercial availability of the rare earths as metals has been very limited. Fabrication of mill products from these metals has not been studied in most cases. This note reports the results of the development of fabrication techniques for thulium. Thulium has a melting point of about 1550°C and a hexagonal close-packed crystal structure. It oxidizes in air to give a black oxide (TmzO,). The procedures for producing thin thulium foil were developed on one ingot weighing about 220 g and were subsequently applied in processing about a pound of metal to foil. Several alternates for the various fabrication steps were investigated and will be discussed. The metal fabricated was in the form of commercial chill-cast ingots 1 in. in diam and 2 in. long weighing approximately 220 g. Impurities in the ingots were reported by the vendor to be 4000 ppni tantalum, 2000 ppm calcium, 200 ppm nickel, 100 to 200 ppm iron, 100 ppm europium, and less than 100 ppm copper, lutetium, and ytterbium. In addition to these impurities, several salt-like inclusions as large as l/8 in. in diam were revealed along the center line of the one ingot sectioned. Preliminary tests indicated that small wafers cut from the as-cast ingot would not fabricate readily by rolling. Forging of copper-jacketed wafers was therefore attempted. At 1550"F forging was satisfactory but an apparent reaction of copper with thulium demanded investigation of lower temperatures. Therefore, the remainder of the test ingot was forged at 1450°F—with only minor cracking. All ingots forged were inserted into copper tubes of 1 in. 1D and 0.125-in. wall thickness. The jackets were sealed by flattening the ends of the tubes and welding under helium. Heating time at 1450°F was 30 min. Press forgings of 1/8 in. per pass were used, followed by 10 min reheats. When the ingots had been squared and reduced to 0.250 in. in thickness, the original copper jacket was stripped off and replaced by a new jacket in preparation for hot rolling. Hot rolling at 1450" F without edge cracking was readily accomplished after forging. Excellent results were obtained with 10 pct reductions of thickness followed by 5 to 10 min reheats. After reduction of thickness from 0.250 to 0.100 in. the copper jacket was removed. It was found, in fact, that hot rolling in air was possible. A tenacious black oxide similar to that seen on zirconium was formed during 3 min reheats at 1450°F. Reduction in air to 0.010 in. foil was possible taking 10 pct reductions per pass. The oxide coat formed during hot rolling in air could best be removed by sand blasting and pickling. Common pickling solutions containing polar solvents were found to attack the metal too rapidly and a concentrated nitric-hydrofluoric acid mixture attacked neither the oxide nor the metal. The most satisfactory pickling solution was 52 vol pct concentrated nitric acid-48 vol pct glacial acetic acid. After forging to 0.250 in., vacuum annealing and cold rolling was found to be another satisfactory alternate to hot rolling in copper jackets. After forging. a hardness of Rockwell B76 was found. Annealing in vacuum (2 X l0-5 mm of Hg) for 1 hr at 1200"F did not alter this value. Annealing at 1470"F for 1 hr brought the hardness down to R;]63. With cold rolling (5 pct per pass) the hardness returned to about R,1:76 after 20 pct reduction and edge cracking became noticeable. However, cold rolling to a total of 40 pct reduction in thickness (RI,,83) was possible before edge crack propagation became serious. Good surface finish was obtained, and the metal loss due to oxidation was minimized by cold rolling and vacuum annealing. Using this procedure the yield of 1.25 in. wide by 0.010 in. thick foil from a 1-in. diam ingot was about 40 pct.

Jan 1, 1961