Search Documents

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By M. J. Deats

INTRODUCTION To prepare the reader adequately, reference should be made to the paper 'The Pioneering of Fully Mechanized Longwall Coal Mining in South Africa' by R. T. Naude and M. J. Deats, published in the February, 1967, edition of the Journal. At the time mechanized longwalling had been proved operationally feasible with encouraging results since its inception in South Africa in mid 1965. Subsequently, further top seam panels were successfully extracted with improved productivity and with some modification to equipment. In 1968, after an overseas visit by mine officials, equipment specific to suit local conditions was acquired and lower seam trials commenced. Despite initial obstacles and difficulties the first panel was successfully mined. Modification and improvements to equipment and techniques resulted in the second lower seam panel being extracted economically during 1969-1970 and with productivity exceeding even that of top seam faces. During extraction of the second lower seam panel, gradual and complete surface subsidence occurred over the panel without affecting face operations. Rock mechanics investigations had originally indicated some uncertainty regarding adverse dolerite sill behaviour which could have caused longwall mining to be hazardous. All such doubts have now been removed. RESUMÉ AS AT FEBRUARY, 1967 Mechanized longwalling was introduced in 1965 on an experimental basis in an effort to improve productivity in the newer area of the mine and to increase the quality of the comparatively dirty run of mine feed to the washing plant. In addition advantages could be predicted in the long term by better utilizing reserves of straight coking coal and increasing the life of the mine. The top seam unit was obtained on a rental basis and by the beginning of 1967, two panels, the first having a face length of 215 m, a panel length of 345 m, seam section of 1 219 mm, and the second the same face length, a panel length of 453 m and a seam section of 1 067 mm had been successfully longwalled. At this stage a best month of 24 602 metric tons with an average of 17 364 metric tons per full working month could be reported. Results were sufficiently encouraging for the company to exercise its right to acquire the equipment as its own asset and from 1967 onward, the unit has operated on this basis. From the point of view of rock mechanics, the dolerite sill over the first two panels was known to have 'bridged', only the material below the base of the sill having truly 'goafed'. No adverse pressure effects had significantly affected face operations except for two 'bumps' towards the end of operations in each panel. Gate road maintenance presented no problem. The strong inflows of water experienced on the first face were now known to be associated with an isolated water bearing fault plane and were not experienced on the second face. TOP SEAM EXPERIENCE - MAY, 1966, TO DATE Panel 2 (February, 1966, to November, 1966) The operations in panel 2 (see Fig. 1 for location of panels) continued uneventfully until the final month in this panel. At this stage, the chocks behaved most inconsistently often lowering under the weight of the canopies alone. Roof trouble became so severe that the unit was unable to produce adequately and blasting of chocks became a daily occurrence. Finally 24 m short of the planned limit it was decided that a complete overhaul was the only solution and the extraction operations commenced. At this time, the only fatal accident associated with longwalling occurred when a Non-White inadvertently fell into the panzer conveyor transfer point at the main gate. Some gate road difficulties in this panel were overcome by bolting tapes to the roof as decking and allowing them to pass over the gate chocks and collapse into the goaf. Two cribbed roof falls were also negotiated by the gate chocks at the face ends without undue difficulties. It was decided in the light of maintenance problems encountered on this face that the best solution would be to appoint a foreman solely in charge of face maintenance crews. This step has to a large extent contributed to success achieved subsequently. Panel 2-face length 213 m panel length 456 m cutting height 1 092 mm average monthly output 16 443 t best month 19 130 t Panel 3 (December, 1966, to June, 1967) By the end of 1966 results were sufficiently encouraging for the company to exercise its right to acquire the equipment. This was negotiated and the unit has operated as such to the present date. Prior to installation in panel 3, all face equipment was thoroughly overhauled underground and the chocks boost-tested to yield-load. The costs of overhauling, including almost complete hose replacement, were much higher than anticipated. Advice had been received that complete hose replacement was common practice after +/- 18 months' operation. Shortly after commencement of operations in panel 3 the chocks again failed as they had towards the end of panel 2. At this stage, the suppliers advised that the valve gear should have been repaired during the overhaul as the needle and seat seals could no longer be relied upon. This operation was impossible to carry out on the face and would have been e1ttremely time consuming. Fortunately a new type of valve gear was then available from the suppliers, termed the capsule-type valve, and a complete change over could be made on the face. The encapsulated valve has a delrin pad sealing over a raised

By Wm. J. McCracken

HISTORICAL REVIEW OF BOARD OPERATIONS The Ontario Worker's Compensation Board was established in law enacted by the legislature of the Province of Ontario in 1915. It was designed to pay insurance benefits to injured workers, and at the same time to protect employers from legal suit. It was based upon an enquiry system rather than an adversary system such as that used in the courts process. Initially, the system was designed to pay compensation benefits and subsequently, to pay for the cost of medical treatment and pensions for disability and disease resultant from the effects of traumatic injury. In 1947, the Act was changed to include industrial or occupational generated diseases, not specifically related to traumatology. Such occupational diseases were therefore accepted and benefits paid subsequent to that date. As will be discussed in several minutes, even today the vast preponderance of compensation claims with the Ontario Board continues to be related to the effects of trauma. HISTORICAL REVIEW OF EXPOSURE TO RADON GAS DECAY PRODUCTS In some areas of Ontario, especially in Northern Ontario, there is a natural leaching of radon gas from the underlying rock formation. This constitutes very low levels of radon gas decay product radiation exposure to those persons coming in contact and inhaling these substances. This paper however is designed to discuss the occupational generated types of radon gas exposures. For many years dating back to the 1930's, partially refined ores were being shipped from Northern Canada to a refinery located at Port Hope, Ontario, still in operation and currently operated by Eldorado Nuclear Limited of Canada. Initially, the purpose for the operation was extraction of radium to be sold on world markets for medical treatment purposes. With the advent of World War II, this market collapsed. Subsequent to World War II, the availability of other sources of radiation for medical radio-therapy generally replaced the requirements for radium. During World War II, a new market opened up for the Port Hope refinery however as work into nuclear chain reactions and the development of the atomic bomb identified the need for uranium and enriched uranium. During the period of operations where radium was being extracted at the Port Hope refinery, it is now known that an identifiable radon gas hazard did exist. This hazard disappeared when the production line for extraction of radium ceased operations. In 1954, uranium mining operations opened up in Ontario at two locations, Bancroft and Elliot Lake. At the peak of operations, 16 mines were operational and 11,000 workers were employed in these mining operations. A high level of mining activity continued over a 10 year interval with the Bancroft Mines closing permanently in 1964 following a 10 year life of operation. The other mines in Elliot Lake closed about the same time with the exception of two uranium mine operations which have continued to be operational up to the present time. By 1965, due to a dramatic drop in world demand for uranium, the total work force had fallen to 1/10 of the peak work force, and approximately 1,300 workers remained in employment. It is of interest to note that one significant difference in the work environment between Elliot Lake and Bancroft was the high silica content of the Elliot Lake ore. This gave rise to a number of cases of silicosis developing in relatively short intervals of time in the Elliot Lake miner population. No cases of silicosis were identified from the Bancroft operations. Based upon the experience in investigating and evaluating actual cases of lung cancer in the uranium miners over the years, the medical staff at the Ontario Board also developed the impression that radiation levels were much higher in the Bancroft operations, especially in the earlier years of operation, than at Elliot Lake. This resulted in accumulation of higher levels of Working Level Months (WLM), usually over a shorter exposure interval in many of the cases. This aspect will be further evaluated in this presentation. Subsequent to 1965, the work force remained quite static in numbers until 1975. At that time, there began to develop an increase in the work force, and this increase is continuing at a moderate rate up to the present. INITIAL METHOD OF HANDLING LUNG CANCER CLAIMS The first lung cancer claims in Ontario from uranium mining operations were accepted on the perceived cause-effect relationship. This relationship was based upon the data from the Colorado observations and the Czechoslovakia data. Initially, a series of regression equations on mortality were developed and used to estimate the effect of exposure to low cumulative doses of radon daughters as it might relate to the frequency of occurrence of lung cancer at any particular cumulative exposure level. A probability of cancer being radiation induced as against it being caused from other factors was calculated. This method was discontinued subsequent to 1972 due to problems encountered in carrying out this complex evaluation. Thereafter, each case was dealt with on an individual basis, being based upon whether or not the tumour was of the oat cell type, a cumulative exposure in excess of 120 WLM; latency periods in excess of 10 years, commencement of mining prior to

Jan 1, 1981

By Jean Howard

ThE formation of the (100) [001) texture in 3-1/4 pct Si-Fe strip was first reported by Assmus ef a1.l in 1957. Since then much experimental work has been carried out with a view to establishing the mechanism involved. The papers cited above state that the (100) [001] texture was developed in strip rolled from material melted and cast in vacuum. (The impurity content of the ingot is reported as 0.005 pct.) The present note records that similar results can be obtained in material processed by powder metallurgy. A processing schedule is described.which enables the texture to be formed in strip up to 0.010 in. thick, but there seems no reason why this should not be achieved in thicker strip, provided that large grains are developed after sintering. The materials were prepared from Carbonyl Iron Powder Grade MCP (particle size 5 to 30 p) of the International Nickel Co. (Mond) Ltd. The powder contains about 0.15 pct 0, 0.01 pct C, 0.004 pct N, <0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni— that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The silicon powder was 99.9 pct purity, or material of transistor quality (ground in pestle and mortar). The mixed powders (3-1/4 pct Si to 96-3/4 pct Fe) are heated in hydrogen at 350" and 650°C to deoxidize the iron before sintering loose at temperatures between 1350" and 1460°C (depending upon the ultimate thickness of strip required) for up to 24 hr. The object of the high-temperature sinter is to develop a large grain size at this stage. Alternatively, the loose sintering can be done at a lower temperature followed by rolling or pressing and then annealing at temperatures between 1350" and 1460°C. Both methods produce large grains, which remain large throughout the process. The compact is then hot-rolled to approximately 1/8 in. with high-temperature interstage anneals if necessary. This step is taken to avoid intercrystalline cracking which would occur if the material of such large grain size were cold-worked. The bar is then annealed at 1050°C and reduced to its final thickness by approximately 50-pct reductions and 1050°C interstage anneals. Throughout the process the dew point of the hydrogen furnace atmosphere is maintained at about -40°C. Samples were annealed in hydrogen at various temperatures and times. Secondary recrystalliza-tion to (100) [001] was developed on the thinner material (i.e., up to 0.002 in.) by annealing in hydrogen at 1050" to 1200°C with a dew point of - 40°C or in vacuum (10-5 Torr) at 1050°C. With the thicker materials (i.e., up to 0.010 in.) the best results were obtained by annealing in hydrogen at 1200°C with a dew point of - 55°C. Complete secondary recrystal-lization to (100) [001] textures was obtained. Above these temperatures secondary recrystallization to (110) [001] tended to develop. The final annealing of samples was normally carried out with the samples placed between recrystal-lized alumina plates, but some experiments were performed with the samples suspended so that their surfaces were not in contact with anything except hydrogen, and these were equally successful in developing secondary crystals. An approximate determination of the proportion of material (before secondary recrystallization took place) having crystals with the (100) or (110) planes in or near the rolling plane showed that 11 pct of the sample had (100) and 16 pct (110). The method used for the determination is described below. A sample was annealed at a temperature just below the secondary recrystallization temperature and etched to reveal the (100) planes. The approximate area covered by crystals having (100) or (110) in or very near the surface was measured on the screen of a Vickers projection microscope. This was repeated for twenty positions chosen at random and a mean of the results calculated. The main hindrance to developing the secondary crystals in the thicker materials was the difficulty of obtaining a large enough initial primary grain size before secondary recrystallization. This was overcome by increasing the particle size of the silicon powder used. During the course of the work, it had been observed that the larger the grain size after sintering the more likely it was that the material would be successful in developing secondary crystals at a later stage. An experiment was therefore carried out to determine whether the material with the larger grain was more successful in developing secondary crystals due to the large grain produced at the sintering state per se or whether it was due to the greater reduction of silica brought about when the sintering temperature was raised in order to increase the grain size. A comparison was made between two compacts, one of which was made with silicon powder of 60 to 100 mesh, the other with silicon powder which was finer than 200 mesh. F?r this experiment, use was made of a phenomenon previously observed that the larger the particle size of the silicon powder employed in making a compact, the larger is the grain size of the compact. The silicon powder was ground

Jan 1, 1964

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of &apos;average&apos; (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by &apos;average&apos;? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual&apos;s quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the &apos;average&apos; Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being &apos;average&apos; recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the &apos;50 per cent of maximum oxygen intake&apos; level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and &apos;optimum&apos; levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors&apos; ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at &apos;optimum&apos; levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that &apos;The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample&apos;. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry&apos;s stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor&apos;s bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By Warren D. MacEvoy

INTRODUCTION Good ventilation bulkheads (stoppings) can be obtained only by conscientiously adhering to four basic principles: carefully selecting the site for the bulkhead, adequately preparing the site, properly constructing and sealing the bulkhead, and checking the results with a smoke tube before leaving the area. If all these guidelines are followed during each ventilation project, a poor job will result only from the use of improper materials and cannot be blamed on carelessness or oversight. SITE SELECTION A perfectly constructed bulkhead in the wrong location can be completely worthless. Conceivably, a bulk-head in the wrong location could cause dangerous ventilation conditions that are difficult to identify and isolate. If the suggestions herein are followed, a considerable amount of work, time, and material may be saved. Perhaps the single most important step is always to select the exact site for a bulkhead before starting construction. Although the latitude in selecting a site may be limited by instructions or operating conditions, it is common to find poor bulkheads built within a few meters (feet) of a site that would have been far superior but was overlooked during the planning process. The ideal site for a bulkhead should have as many of the following features and conditions as possible: 1) To provide a solid bulkhead, the selected site should be in firm and unbroken ground. 2) To minimize the amount of work and material required and to minimize the danger of later damage to the bulkhead, the site should have as small a cross section as possible. 3) The bulkhead site should not be encumbered by interferences such as pipes, wires, ditches, wire roof supports, trash, muck piles, etc. 4) The walls and timbers of the site should be free from oil, grease, or tar that would inhibit adhesion of the sealant used on the bulkhead. 5) Unless special precautions are taken, the site should not have water seepage, standing water on the floor, or water-carrying ditches. 6) To expedite construction of the bulkhead, the site should have reasonable access to transportation, supplies, communication facilities, and compressed-air lines. 7) The site should have a reasonably level floor, allowing direction of the bulkhead door swing to be reversed at a later time if so desired. In a steeply sloping location, it may be possible to open the door in one direction only. SITE PREPARATION Once a suitable site has been selected for the bulk¬head, it must be prepared properly. All site preparation work should be completed before starting any construction work on the stopping itself. Unfavorable site conditions can be identified during the course of thepreliminary site preparation, saving time, effort, and materials that otherwise might be wasted. The follow¬ing preparation steps help assure the construction of a good stopping: 1) If wire mesh has been used at the site, a strip 457 mm (18 in.) wide should be cut and removed from the walls and roof at the selected location. 2) The exposed strip of rock should be barred down thoroughly to provide a smooth surface. 3) All obstructing materials should be removed, including old timbers, pipes, rockbolts, wires, etc. If a conduit must cross the bulkhead area, it should be located or relocated away from the floor, walls, and roof to allow a 6.28-rad (360°) seal around the juncture between the conduit and the bulkhead structure. 4) All loose muck should be cleaned from the site and a trench about 152 mm (6 in.) deep should be dug from wall to wall in the floor. The trench must be wide enough to accommodate the entire bulkhead, including the posts. 5) The rock surfaces of the walls and roof should be cleaned with a wire brush to remove as much loose surface material as possible. Thorough cleaning promotes adhesion of the bulkhead sealant to the surfaces of the walls and roof, thus promoting an airtight seal. 6) It is quite difficult to seal landing mats that cross a bulkhead. If such a crossing cannot be avoided, the bulkhead should be placed between the end and the first hole in the steel so at least one side of the bulk-head can be sealed easily and completely. That may have to be done prior to actual construction if the end is located on the opposite face from the seal coating of the bulkhead. BULKHEAD CONSTRUCTION The three principal considerations in bulkhead con¬struction are the type of bulkhead, materials to be used, and construction method to be employed. For many projects, the bulkheads are specified by the requesting agency, with no latitude for independent choice of the type, materials, or construction method. In such cases, any deviations from the specifications, for any reason, must be approved in advance by the proper department or by the project senior ventilation engineer. Types and Materials When a choice of type, materials, or method is allowed, consideration should be given to factors such as cost, required useful life, proximity to blasting concus¬sions, availability of materials, direction of permissible air leakage, and degree of airtightness required. Other factors to be considered include the amount of time available, accessibility of transportation, potential for interference with operations or production, ambient water conditions, availability of connections to com¬pressed-air lines, etc. Despite the multitude of factors to be considered, most stoppings can be analyzed easily and the proper choices can be made without much difficulty. The four common classes of bulkheads utilized in

Jan 1, 1982

The October General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th October, 1969, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present 17 Members, Messrs: M. Barcza, R. C. J. Goode, J. A. Nixon and V. C. Robinson (Council Members), M. L. Fitzgerald, D. F. H. Graves, C. G. Hinds, S. D. Hill, J. S. Hall, D. F. Malan, T. Meyer, W. pyne-Mercier, K. S. Rae, S. G. Taussig, L. W. P. van den Bosch, Dr A. Whillier, C. H. Wyndham. Four Associate Members: Messrs O. Davel, M. J. Martinson, M. P. J. Sandys, T. G. Harington. One Student: R. P. W. Henrard. Three Visitors: Messrs A. V. Pike, B. Schmitz, A. P. Raats. Secretaries: D. C. Visser and S. de. Gersigny. Total present: Twenty-eight. OBITUARY The President: "It is my said duty to announce the death of Pieter Ulrich Fischer, Member, who joined the Institute in 1961 and passed away on 24th June, 1969. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments&apos; silence." MINUTES The President: "The minutes of the last meeting will only appear in next month&apos;s Journal and I would request that the confirmation of these minutes be held over." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades:" Members: Alexander Edward O&apos;Meara, Anton Leopold Melvill, WilIiam Harold Wise, Eric John Dunstan, Frank Nel, Lubertus Hendrikus Jakob Poortier. Associate Members: Michael Irvine Britten, Selwyn Wilson Lange. James McCormack, Christiaan Lodewyk de Jongh, WilIiam Andrew Hustrulid, Reinhold Johannes Ortlepp, Felix Henry Lancaster. Graduates: Willem Adriaan Gericke, Hamish David Sneddon Miller, David lan Ossin, Robert Antony Layboume, Ewart John Shillaber, Colin Hewitt Wiggett. Affiliates: Bernard Andre Thomas, Waiter Arthur Wood, Andrew John George Paschalides, David John Perry, Alex Richardson, Gert Blekker Kotze. Student: Matthys Jacobus de Beer. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: David Alphonso Viljoen. From Student to Associate Member: Michael Charles Carruthers. "I welcome the newly elected members to the Institute and congratulate the members who have been transferred to a higher grade." PAPERS FOR PRESENTATION The President: "Professor Wyndham, may I call on you to deliver the paper entitled &apos;Factors affecting the mechanical efficiency of men shovelling rock in stopes&apos;, written jointly with J. F. Morrison, J. H. Viljoen, N. B. Strydom and A. Heyns." After the presentation of the paper the President said: "Gentlemen, I would like to thank Dr Wyndham and his colleagues for once again reporting through the medium of this Institute the results of the very important work they are carrying out at the Human Science Laboratories. It is most appropriate that this work which is leading to a better understanding of the capabilities and efficiency of the human body under the arduous conditions encountered underground should be reported to this forum. In this way our members, who are actively engaged in the job of mining, can firstly learn something of this research and secondly, can, with their practical knowledge of conditions underground, contribute to what has been learnt and possibly pose new problems for our scientists in the laboratories. The scientist should always have the opportunity of subjecting his research to the scrutiny of people engaged in practical operations. By the very nature of our gold mines we are unfortunately heavily dependent on a large labour force and while mechanization has been introduced wherever feasible, we are likely to continue to be heavily dependent on this labour. In accepting this fact we can be proud in this country of what has been achieved, not only in obtaining the best efficiency from labour but in ensuring that their working conditions are reasonable and that their health and well-being are adequately cared for. When one visits our gold mines, one cannot help being impressed with what is being done to ensure that we have a satisfied, happy and healthy labour force. The Human Sciences Laboratory with its scientific approach has assisted greatly in promoting a better understanding of the problems associated with labour under the conditions experienced on our mines. Thank you." Mr M. Martinson then contributed to the discussion. (This contribution will appear in a later issue of the Journal.) "Professor Wyndham, may I call on you to deliver the paper entitled &apos;Acclimatizing men to heat in climatic rooms on mines,&apos; written jointly with Prof Strydom." After Dr Wyndham had presented the paper the President said: "Thank you Dr Wyndham for so ably describing the work associated with the acclimatization procedures on our gold mines. It has certainly been an eye-opener to those of us not familiar with this work and I believe it is very important that everyone and not only people in the gold mines should know about it. It is fortunate that all industries do not have the same arduous heat conditions experienced on our mines but other industries such as our chemical and metallurgical industries do have other problems relating to the adjustment of labour to the work situation. The scientific approach employed by the gold mines in tackling this problem is an example to these industries of what can be achieved by logical

By More-O&apos, R. C. Ferrall, J. W. Wilson

Discussion: M. D. G. Salamon* (Fellow): The theoretical principles behind the techniques of calculation used by the authors was formulated and published during the period 1962- 65. These principles, together with their practical implications, were summarized in a review paper in 1966.1 Now, in February, 1970, we have this long and comprehensive paper discussing the practical application of the theory. I think this is good progress. The large number of practical examples treated in the paper clearly demonstrates not only the skill and knowledge of the authors, but also the versatility of the techniques of analysis. I feel that the techniques described by the authors, and their improved versions, will revolutionize mine planning. I suggest that no shaft system or stoping layout should be planned in future without an adequate rock mechanics analysis. It seems that it will be progressively more difficult to white wash mistakes in rock mechanics and attribute their costly outcome to normal mining risk. We should not, however, become complacent. There is still a lot to learn and do in the future. I do not want to discuss tonight the question of further research but instead, I will raise two other problems which may hinder the future progress of practical rock mechanics. To carry out work similar to that described in the paper, mine managements require men who are capable of doing the work and who have the most efficient techniques of analysis at their disposal. As a research engineer I have been associated with the development of techniques of analysis. I can assure you that these have undergone an amazingly rapid development during the last six years. We have seen the change from the use of the electrolytic tank analogue and manual integration to the method described by the authors, that is, to the employment of the automatic network analogue and computer integration. But this is not the end. In a recent paper Prof R. P. Plewman2 and his co-authors described a completely digital technique. Here the process of calculating on- and off-reef quantities is integrated into one computer run. But these sophisticated methods of computation are useless without men to make intelligent use of them. During the last few years a new breed of mining engineers has appeared on the scene - the Rock Mechanics Engineer. I feel it is timely to call the attention of the senior members of this Institute to the fact that this new breed will succeed in carrying out its duties in a valuable manner only if we manage to attract to its ranks young engineers of the right quality. The requirements are high. The top rock mechanics engineers have to be good mine planners and they have to understand the essence of sophisticated theories. Without these attributes they will not succeed in the long term and the industry will not gain the benefit of available knowledge. To attract this quality of engineers the industry will have to ensure that rock mechanics is accepted by all concerned as a career which could lead to the top echelons of our profession. Finally, I would like to make one or two remarks concerning Part I of the paper. In Sections 3.1 and 3.2 the authors describe methods of determining the normal stress on the reef plane and the convergence distribution in the excavations. The description as given applies only to a horizontal reef. When the reef is inclined the situation is more complex since a shear component of stress on the intact reef and a ride component in the excavations must then also be determined. These can be calculated by methods similar to that described in the paper.3 The practical application of the method of calculating the released energy (Section 3.4) is in the comparison of various stoping layouts to establish an order of preference in terms of decreasing rates of energy release. To carry out these comparisons effectively, the calculations must be carried out in a manner by which the values of energy per unit area obtained are comparable. I would like to note in this respect that the method of calculation given in the paper is valid without reservation only if there is no elastic contact between the hanging and foot walls in the mined-out area. If there is contact then the calculated energy values are correct only if the mined out area is increased in small steps during the analysis. My second point in this regard is concerned with the practical method of calculation as described in Sections 3.4 (ii)-(iii). Firstly, I would like to suggest that the energy calculation should be carried out, as far as possible, by using always the same scale on the analogue. Secondly, the reading of current on a pin should be followed by the removal of that pin to obtain the corresponding reading of potential. The product of these two values will be proportional to the energy released during the mining of the small area corresponding to that pin. The method suggested by the authors tends to mask possible danger points in the layouts, since they obtain an average value for a time period, say, for six months.

By C. S. Finney, John Mitchell

On December 31, 1959, there existed in the United States 15,993 slot-type coke ovens capable of producing 81,447,700 net tons of coke. These ovens were concentrated in 74 coke plants in 21 different states. As of the same date, there were 7448 beehive ovens in existence at 45 plants in the states of Pennsylvania, Virginia, West Virginia, and Kentucky. Total annual capacity of the existing beehive ovens was 4,368,800 net tons, but only 5148 ovens with a capacity of 3,131,600 tons were in operating condition. It is interesting to compare the average dimensions of slot-type ovens built during recent years with the 30 ft x 5 ½ ft x 16 ½ in. ovens erected at Syracuse, N. Y. in 1892. A composite oven built according to the average dimensions of all those erected between 1954 and 1958, for instance, would be 39 ft long. 12 ft high, and 18 in. in width. The coal capacity would be 16 tons as against the 4.4 tons which could be charged to the Syracuse ovens. Of the 15.993 slot- type ovens in existence at the end of 1959, by far the greater number were built by the Koppers Co. whose total of 11,280 ovens included 7891 Koppers- Becker and 3389 Koppers ovens. Of the remainder, there were 3260 Wilputte, 1350 Semet-Solvay, 63 Otto, and 40 Simon Carves ovens. By-product coke oven plants are usually classified either as furnace or merchant plants. According to the definitions used by the US Bureau of Mines, the former are "those that are owned by or financially affiliated with iron and steel companies whose main business is producing coke for use in their own blast furnaces. All other coke plants are classified as merchant. They include those that manufacture metallurgical, industrial, and residential heating grades of coke for sale on the open market; coke plants associated with chemical companies or gas utilities; and those affiliated with local iron works, where only a small part (less than 50 pct of their output) is used in affiliated blast furnaces." The annual coke capacity of the merchant plants during 1959 was 10,393,000 tons. However, the by-product oven of today is essentially an appurtenance of the iron and steel industry, rather more than 87 pct of total by- product coking capacity being concentrated at furnace plants. This was not always so. There was a time when the merchant plants played a much greater part in meeting the US demand for coke and gas. High noon for the merchant plants was reached during the early 1930&apos;s. By 1932 there were as many by- product oven installations being operated by the merchant sector of the industry as by the coke divisions of the iron and steel industry (44 of each), and in the same year the merchant plants produced 46.5 pct of all by-product coke made in the country. Since that time their contribution has drastically declined. In 1940 merchant plants were responsible for only 23.2 pct of total US production, and by 1950 their number had decreased to 30 plants which turned out 18.5 pct of the total by-product coke made. At the end of 1959 only 20 of the 74 existing by-product oven installations were merchant plants. They ac- counted for 12.5 pct of the year&apos;s production, or 6,849,786 net tons. This percentage has remained fairly constant since 1954. There are several reasons for the decline of the merchant coking industry. For example. On the grounds of economy, quality control, continuity of supply, and so on, the iron and steel industry usually prefers to control its own mines and carbonize its own coal at or near to the blast furnace rather than rely on independent operators for metallurgical coke. As the steel companies have enlarged their own coking facilities, so has the need for coke obtained from other sources declined. Furthermore, not only has the steel industry increased in self-sufficiency by building mare coke ovens during recent years, but it has also progressively improved the fuel efficiency of its blast furnaces. During the years 1947-49 the average coke consumption per ton of pig iron was 1892.8 lb. During 1958 the corresponding figure was 1613.4 lb. There are many individual furnaces where still better results are being obtained, and further reductions in the average may be expected. Perhaps the greatest threat to the merchant coking plant has been the fantastic increase in the use of natural gas and petroleum products for purposes which manufactured gas once served. So deadly has the com- petition from natural gas and oil been that it has almost eliminated by-product oven installations owned by public utilities. In the peak years of the early 1930&apos;s there were 23 such public utility plants. In 1960 only two were left. One of these, owned by the Citizens Gas and Coke Utility, was at Indianapolis, Ind.; the other was the plant operated by the Philadelphia Electric Co. at Chester, Pa. The non-utility merchant plants have also been sorely hit. With gas sales revenues reduced, domestic

Jan 1, 1961

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day&apos;s data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may &apos; be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor&apos;s bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By J. Quigley

As the outcrop mines in the West developed into underground operations, systems of ground support were gradually evolved. In the early coal mines there was little need for support except near the dirt line in portals, where stone masonry was common. Where the top was shaley or broken, native pine props with light cross bars and legs furnished enough support even in Utah&apos;s 25-ft coal seams. As depth of workings increased. roofs and backs of the same general nature as those near the surface became more and more unstable and required more and more support. Some coal airways show this tendency very clearly. From the surface down the same type of roof shows deterioration which an experienced eye can translate into a measure of depth under surface rather than change in rock characteristics. Rock bolts, developed by various companies and by the U. S. Bureau of Mines, have become an effective substitute for timber in sections of some metal and nonmetal mines formerly requiring escessive timber support, and further use of war surplus landing mats, chain link fencing, and a new punched channel developed by one of the steel companies has enabled other mines to operate deposits where costs of timber and lack of clearance for timber support would have prohibited mining. The block caving mines have made extensive use of reinforced concrete underground to achieve similar ends under difficult conditions. Steel sets are standard in many Bureau of Reclamation projects, although these are usually covered in with concrete to make the permanent structures the Bureau&apos;s reclamation projects require. But the use of steel in mining operations is limited and has been confined principally to the iron ore mines of Michigan, Wisconsin, and Minnesota. Some mines have installed used rail as posts, caps, and crossbars, but a rail section is not suited for load carrying, and used rails are generally brittle. having a tendency to fail without warning when overloaded. European mines were the first to reach the size of worked out areas and depths of cover resulting in major roof problems. The Europeans resorted to pack walls and masonry walls, in conjunction with timber arched sets. rail arches, and combination timber and rail and steel arches. The give in these pack walls and wooden blocking was supplemented by a hinge in the center of the arch. This design is called an articulated arch Through various refinements of this principle of the support giving graduallv with the load. Toussaint-Heintzmann developed the yielding or sliding arches, in which yield is accomplished by friction in the overlapping joints of the arch. This type has gained widespread acceptance in the Ruhr and Lorraine Basin and is being manufactured by Bethlehem Steel for sale in this country. In North America the anthracite mines in Pennsylvania, followed by certain iron ore mines in upper Michigan and Canada, were the first to employ these arches to any extent. The practice was later adopted by Kennecott at Ruth, Nev., and by others. Despite high initial cost, the use of these arches is growing in many parts of the country because of their suitability in heavy ground. In its present form of manufacture the yield-able arch consists of open U-shaped rolled section with heavy beads on the edge. The open edge of the U is placed toward the wall. The section nests in another section of the same dimensions, and an arch can be built up from rolled radii and tangents of various weights and lengths. Sections are fastened together by U bolts and saddles. The lap on the joint varies from 12 to 24 in., and ordinarily the bolts are tightened with a 1-in. drive air wrench. The arches are spaced with channel struts held by J bolts and saddles. Sections can also be obtained that are composed of various combinations of radii and tangents and true circles. The joints can be placed to bear against anticipated loads and asymmetrical loads imposed by dipping strata. In the arches now being manufactured clearance widths up to 19 ft are obtainable in weights of sections from 9 to 30 lb per ft. The circular cross sections are available in the same weights ranging from 8 to 16 ft diam. At present most of the arches sold are supplied only in carload lots. It is hoped that demand will grow so that distributors can stock various weights and sections to give small operators a chance to try this new type of rock support under their own particular conditions. Several excellent papers have discussed the properties of various sections now manufactured, the dimensions of the sets obtainable, and their application under widely differing conditions. The present article will describe the methods and results of a special use of the arches at Kaiser Steel mine No. 3. Sunnyside, Utah. Problem at Mine No. 3 : In 1953 Kaiser Steel Corp. laid out Sunnyside mine No. 3 to recover coking coal left by the previous operator, Utah Fuel Co.. below workings that had been abandoned in 1928. Two seams had been worked, the upper and lower, separated by 30 to 42 ft of rock. Approximately 10 million tons of coal had been extracted from this area some 3000 ft down the itch from the outcrop to a 1500-ft depth of cover. The mine had been opened by slopes in both upper and lower seams. Sometime in the late 1920&apos;s the lower slope

Jan 1, 1960

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.&apos; A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.&apos; A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world&apos;s largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

By Francis Collins, E. R. Brownscombe

A study has been made of the material balance-fluid flow method of estimating reserves and degree of water drive from pressure and production history data. By considering the effect of random pressure errors it is shown that in a particular example a standard deviation of three and one-half pounds in each of ten pressure survey? permits the determination of the reserves with a standard deviation of 8 per cent and the water drive with a standard deviation of 15 per cent, assuming that certain basic geologic data are correct. It is believed that this method of estimating reserves and water drive is useful and reliable in a number of cases. The method is particularly valuable when reservoir pressure data are accurate within a very few pounds, but may also be applied with less accurate pressure data if a relatively large reservoir pressure decline occurs early in the life of the field, as for example in an under-saturated oil field. INTRODUCTION A knowledge of the magnitude of reserves and degree of water drive present in any newly discovered petroleum reservoir is necessary to early application of proper production practices. A number of investigators have contributed to methods of relating reserves, degree of water drive, and production and pressure history. 1-8 Three types of problems of increasing complexity may be mentioned. If a reservoir is known to have no water drive. and if the ratio of the volume of the reservoir occupied by gas to the volume of the reservoir occupied by oil (which ratio permits fixing the overall compressibility of the reservoir) is known, then only one further extensive reservoir property remains to be determined, namely the magnitude of the reserves. A straightforward application of material balance considerations will permit this determination. The problem becomes very much more difficult if we wish to determine not only the magnitude of the reserves but also the magnitude of water drive, if any, which is present. In principle, a combination of material balance and fluid flow considerations will permit this evaluation. Finally, if neither the magnitude of reserves, the degree of water drive, nor the ratio of oil to gas present in the reservoir is known and it is desired to determine all three of these variables, the problem could in principle be solved by a fluid flow-material balance analysis which determines the overall compressibility of the reservoir at various points in its history. The change in compressibility with pressure would provide a means of determining the ratio of gas to liquid present, since the compressibilities of gas and liquid vary differently with pressure variation. However, in practice this problem is probably so difficult as to defy solution in terms of basic data precision apt to be available.&apos; It is the purpose of this discussion to illustrate the second case, which involves the determination of two unknown variables, single phase reserves and degree of water drive, from pressure and production history and fluid property data, and to study the precision with which these unknowns can be determined in this manner in a particular case. Although an electric analyzer developed by Bruce as used in making the calculations to be described, numerical methods necessary in carrying out the process have been devised and have been applied for this purpose. Schilthuis,&apos; for example, developed a comprehensive equation for the material balance in a reservoir. He combined this with a simplified water drive equation, assuming that the ratio of free gas to oil was fixed by geological data and that a period of constant pressure operation at constant rate of production was available to determine the constant for his water drive equation. On this basis he was able to compute the reserves and predict the future pressure history of the reservoir. Hurst developed a generalized equation permitting the calculation of the water drive by unsteady state expansion from a finite aquifer. He showed in a specific case how the water influx calculated by his equation, using basic geologic and reservoir data to fix the constants, matched the water influx required by material balance considerations. Old3 illustrated the simultaneous use of Schilthuis&apos; material balance equation and Hurst&apos;s fluid flow equation for the determination of the magnitude of reserves and a water drive parameter from pressure and production history. He used this method to calculate the future pressure history of the reservoir under assumed operating conditions. As a basis for determining reserves, Old assumed a value for his water drive parameter and calculated a set of values for the reserves, using the initial reservoir pressure and each successive measured pressure. The sum of the absolute values of the deviations of the resulting reserve numbers from their mean value was taken as a criterion of the closeness of fit to the experimental data possible with the water drive parameter assumed. New values of the water drive parameter were then assumed and new sets of the reserves calculated until a set of reserves numbers having a minimum deviation from the average was established. The average value of- the re-

Jan 1, 1949