Search Documents

By D. R. Baughman

Copper oxide deposits that may be considered for in situ leaching exist in unique geologic settings, different from uranium deposits. A large number of interrelated factors must be considered in wellfield design. Many of these factors are hard to quantify and are directly related to geologic features of the orebody. This paper discusses some of the important factors in wellfield design and suggests an outline for a design procedure.

Jan 1, 1988

By T. A. Edison

A distinct hydrocarbon maturation anomaly coincides with the Gold Acres open pit, Nevada (Figure 1). Both atomic hydrogen to carbon (H-C) ratios and reflectance measurements of contained organic matter indicate significantly higher maturity in samples collected within the confines of the open pit than in samples from the surrounding region (not shown in Figure 1).

Jan 1, 1987

By M. Irish

This paper describes the emergency water control measures used at Pegasus Gold's Zortman Landusky mine during the September 1986 flood. The amount of solution stored increased by approximately 78 165 m3 due to receiving 0.2134 m of rain in a 24 hour period. Three methods of water disposal will be discussed including continuous chlorination, batch chlorination, and reverse osmosis. A water management program will also be discussed.

Jan 1, 1988

By H. H. Kleizen

The operation range and efficiency of dewatering apparatus are important factors in the selection of an apparatus for a given purpose. In this paper theories are presented allowing to predict these basic characteristics for different dewatering apparatus and compared with experimental and practical data obtained on coal and ore slurries.

Jan 1, 1989

By David M. Holmes-Smith

Many attempts have been made to design and build an AUV that is small, meets the sensing objectives and is cost effective. Many inventors have already designed smaller vehicles but the problem observed is an increased vehicle instability resulting in instrument instability where data gathered is not trustworthy. Additional problems include instrument weight to vehicle weight ratios and the lack of space for power storage and electrical components. The UFOceanic seeks to remedy these concerns by employing a completely different design and propulsion system. Still in the design stage ? now with a mock-up unit for testing, the results are encouraging. We have chosen a very low voltage embedded systems design using multiple PIC processors and fuzzy logic programming. We are designing the craft to rotate for stability and to provide friction reduction to minimize the need for instrument stability compensation and propulsion power. Additionally, we are looking and experimenting with a number of power plant drive systems including flywheels, GNP (plasma), fuel cells and more conventional systems. We of course plan for the UFOceanic to run for months at a time supported by a self-charging system.

Jan 1, 2001

By J. M. Keane

Critical to successful dump and heap leaching for copper is an adequate testing program for evaluation of the applicable parameters. This paper deals with testing methods to establish best conditions for dump and heap leaching of copper so that commercial operations can proceed on a rational basis. Discussion is also offered of ore occurrences suitable for dump and heap leaching.

Jan 1, 1985

By Richard Harrison, Frank Lim

"Lifting of slurry from the seabed mining machine to the surface production vessel is a critical element of any deepwater seabed mining system. A Vertical Transport System (VTS) comprises pump(s), riser string, connectors and hang-off assembly as its main components, but it is the pipe material, riser configuration and installation method that often attract the most discussions.This presentation will feature important VTS design work 2H has done over the years for different stakeholders, and highlight the work carried out as a partner to the EU funded Blue Mining Joint Industry Project.The key challenges faced by a deepwater VTS are:??High riser payload??Large deck space for storing riser joints??Long time to deploy and retrieve riser??Uncertain metocean conditions??Vortex induced vibrations??Weld and connector fatigueIncreasing the water depth further sees the longer and increasingly ‘springy’ riser experiencing axial resonance caused by wave induced vessel heave motions being close to the riser resonant period. This can lead to snatch loading and fatigue failure in the riser.The presentation will discuss the above design issues, analysis requirements and provide guidance on pump/riser selection. Solutions to mitigate the resonant response issues will also be proposed.."

Jan 1, 2017

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By S. Rajendran

Much advance has been made in offshore hydrocarbon exploration and exploitation in India. But the same amount of success could not be achieved in the case of other offshore minerals which are amenable for mining. However, employing present technology, there should not be any difficulty in successful exploitation with minimum environmental hazards. A demonstration is provided by considering the conditions prevailing in the Kerala offshore (southwest coast of India) scenario of monazite, ilmenite, phosphatic mud and calcareous deposits. Mud banks are unique phenomenon of the Kerala coast during monsoon season. Acting as barriers to waves, mud banks protect portions of the beaches from being eroded and trap sediments from either side facilitating growth of adjacent beach. The easy minable possibilities of the phosphatic mud during non-monsoon season with less pollution hazards and dumping back the waste material after processing for phosphate at the breaker zones to reduce the erosional effects on the coast make the exploitation economic and ecofriendly unlike the benefication of the lowgrade phosphate ores on land on a comparatively larger area and subsequent crushing, transport and resulting pollution.

Jan 1, 1993

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"The effects of mixed collectors on some physicochemical parameters (thin film lifetime, kinetics of expansion of the three-phase contact, equilibrium three-phase contact angle and surface tension) involved in the elementary act of flotation were investigated experimentally.We have used the microscopic thin balance developed by Scheludko et al (1970) to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates at 1:1 molar ratio. The experiments were performed at a range of concentrations at pH 6.5. The equilibrium contact angle was measured with a microscope technique using the modified Mingins-Sheludko method (Mingins and Scheludko, 1979). The surface tension was measured by the method of Wilhelmy (Adamson, 1960). It was found that the mixed surfactants caused lower contact angles, lower rates of the thin film rupture and longer film lifetime, compared to the pure amine system."

Jan 1, 2003

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By Mitsuhiro Shibazaki

Generally, water-soluble polymers are effective in convergence of water jet ejected from a nozzle as they add viscosity to water. However, excessive additional polymers (added to keep water viscous) could increase friction on the contrary. Therefore, we have totally modified the jetting system from every possible aspect, such as the shape and upstream conditions of a nozzle in order to keep the flow spread to the minimum as stated in my presentation.

Feb 10, 2003

Joy Mining Machinery has developed a new generation of ultra-heavy shields for Anglo Coal Australia?s Moranbah North Mine in the Bowen Basin region of Queensland. These are the largest two-leg longwall shields yet produced by Joy. The longwall at Moranbah North posed a number of challenges, among them a thick, inclined, sometimes undulating seam with increasing depths. The result of this was the need for larger, heavier, more powerful roof supports. Knowing that future longwalls would be going deeper, mine management determined that shield yield ratings of at least 1,750 t (1,930 st) was what would be required.

Jan 1, 2011

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By T. W. Mattioli

Restrictions on fugitive emissions and crushing operations continue to get tighter. Although fugitive dust control in the gold mining industry has historically been difficult, there are now several options that can make dust control both effective and efficient. Using new technology, mine operators can now design and maintain a dust control program that can reduce product losses, decrease equipment failure, cut cleaning costs, and meet air quality compliance standards as well as provide a better working environment. This paper discusses the sources of fugitive emissions related to the gold mining and crushing operations and describes effective new control methods.

Jan 1, 1998

By AIME AIME

JOHN LIVERMORE CHRISTIE belongs to that group of metallurgists who entered the industrial field during World War I and have been responsible for many of the important metallurgical developments since that time. He was born in Montclair, N. J., on Jan. 31, 1894. After graduating from Montclair High School he attended Sheffield Scientific School, Yale University, received his Ph.B. degree in chemistry in 1915 and that same year was employed by the Bridgeport Brass Co. in its laboratory. Among his first duties was the return to Sheffield Scientific School for two years of graduate work in metallography under C. H. Mathewson; receiving his M.S. degree in 1917. Thus we see him becoming one of that group of eminent physical metallurgists who, with Dr. Mathewson's teaching as a foundation, have done outstanding work in metallurgy.

Jan 1, 1945

By R. C. Mahon

Operators concerned with the destruction of their piping by acid mine waters will be interested in the method by which this problem was solved at the Cardiff mine of the Homer group. Rubber lined, or acid resisting metal pipes were found too expensive. Casting concrete lining in pipe would have required a minimum thickness of one inch, thus excessively reducing the pipe's diameter, as well as taking twenty four hours per length of pipe. The Naylor Pipe Co. of Chicago, having experimented with centrifugal lining of pipe with concrete, provided information which eventually solved the problem. An experimental plant was constructed as shown, and the following procedure developed : (1) Kerosene is used to remove the interior oil coating of new pipe. Closed with blank flanges, the pipe is revolved for eight minutes at varying speeds. Stopping and starting the motor achieves a good washing action. The kerosene is then drained off, and similar washing action with caustic soda removes any excess. Swabbing in done with burlap fastened to a 1/2-in. pipe. (2) The aggregate, made of one. part quick-setting cement and two

Jan 1, 1949

The 1980's has seen a revolution in gold mine developments in Australasia. We are witnessing a near ten fold increase in all phases of gold mine development ranging from exploration through to production. Ounces produced have yet to mirror this activity but have increased from a low point of 600,000 in 1980 to 1,800,000 ounces in 1985 in Australia alone. In 1980 the region had less than 10 gold mines, yet 14 new mines started production in 1985 and as many as 28 might start up in the next 18 months. Developing gold mines in the 1980's in Australasia has not been the easiest of jobs, yet the great number of new developments suggest that we have entered a new era that will rank in history along with the 1850's, 1890's and 1930's as high points.Within- our Australasian region two very distinctive styles of gold deposits are being discovered and developed. On the Australian mainland the new mines are in geologically old rocks and are mostly the low grade haloes surrounding worked out high grade deposits. Most are limited life open pit operations depending on recent innovative carbon-in-pulp or heap leach technology. In the Pacific Islands region the style of discoveries are geologically recent, large bulk-low-grade deposits often geologically analogous to porphyry copper deposits. These deposits are typically 10 to 20 times larger than those being proved up on the Australian mainland.

Jan 1, 1986