Search Documents

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By E. S. Yan, R. Graley

"The StackCell was developed to overcome the engineering and design challenges that are commonly associated with existing flotation technology such as pneumatic, self-aspirating cells, mechanical cells, and flotation columns. These challenges include high energy consumption, large floorspace requirements, and size. They are most evident when designing systems to process streams containing a high volumetric flow rate coupled with a significant float yield. Unlike many metalliferous and industrial mineral applications, fine coal flotation circuits are typically characterized by feed streams containing a low solids content (<5%, by weight) where up to 85% of the feed can report to the product launder. With input from major engineering houses and end-users, the Eriez Flotation Division (EFD) developed the StackCell technology with the goal of providing an additional flotation option for end-users. This technology was designed specifically to overcome these challenges by providing an efficient method of separation in terms of metallurgy, but also with respect to equipment size, energy consumption, and installed costs. Besides being placed in tandem with existing cells to provide cost-effective supplemental capacity, this technology can be installed in a stand-alone arrangement as recently demonstrated at Patriot Coal’s Kanawha Eagle preparation plant. This manuscript provides an understanding of the underlying fundamentals of this new technology and presents data from Kanawha Eagle in addition to other industrialscale installations.INTRODUCTIONOver the past decade, column flotation has continued to gain acceptance as an alternative method for recovering fine coal due to superior metallurgical performance as compared to mechanical flotation cells. This point has been proven on numerous occasions by comparison of plant flotation data with the release analysis separation curve (Dell et al., 1972). Data from a release analysis test approximates the ultimate flotation response of a coal sample. In North America, a number of investigations have been published that document bottom-line improvements achieved using column cells (Luttrell et al., 1999; Kohmuench et al., 2004; Baumgarth et al., 2005). According to these reports, the benefits are derived from an overall increase in plant yield that can be achieved due to the improved product grade in the flotation circuit. In particular, the application of wash water to a deep froth utilized in column flotation minimizes the nonselective recovery of high-ash ultrafines that are hydraulically entrained in the froth by conventional flotation machines."

Jan 1, 2013

By Brian Flintoff

"When I was first asked to prepare this paper and presentation in late June, I thought it might be fun to ""step back and paint the bigger picture."" Having attempted to do this, fun is not the first descriptor that now comes to mind, and speaking dyslexically, I've had 'nuf.'Unlike Nostradamus, or even Orwell, I've discovered that I'm ""clairvoyantly challenged"" and not even the psychic hot-line was of much help, at least with respect to process control! I am somewhat comfortable speculating on evolutionary change, but the radical developments that will arise from revolutionary changes are well beyond my mortal capabilities. Even with evolutionary change, I'm reminded of the lessons of time series analysis which show the prediction error to grow exponentially as the horizon moves into the future. As Macluhan is reported to have said: ""Predicting the future based on the past is a little like driving your car while looking in the rearview mirror!""Having honestly presented my qualifications, allow me to try to look at process control and to offer some conjecture on where we're probably headed. In the end, it is said that: ""The plant of the future will have only two employees, a man and a dog. The dog will be there to keep the man from touching the equipment.1""IntroductionA little less than a decade ago Andy Mular and I co-edited a monograph entitled ""A Practical Guide to Process Control in the Minerals Industry."" The work was commissioned by the senior management of a consortium of Canadian mining companies, since it was widely perceived that control was an area of great economic potential, but one that had not been effectively tapped. The concern was that if the industry could not soon deliver on the ""potential"", the term may well have appeared in the epitaph of what was, to these men, a very attractive investment opportunity. I think it is fair to say that over the past few years process control has clearly established itself as an essential technology in plant operation and optimization. That isn't to say that we get it all-right, all-the-time, but, the circumstances are much different than they were. In the eyes of many, process control has attained the distinction of being considered a mature technology, even though there are still countless avenues for exploration."

Jan 1, 1998

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By G. B. Michaels

Exploration programs for mineral resources often involve analysis of soils or stream sediments for the mineral being sought or its pathfinders. Because many metals are toxic to microorganisms, patterns of metal resistance in soil or aquatic populations may provide additional useful information at a reasonable coat. These patterns in some cases have been more effective than the soil geo-chemistry and may be easier to obtain. Elevated levels of resistance to silver and its path-finders have been demonstrated in stream populations from an area of known silver deposits, and resistance to gold pathfinders has been demonstrated for gold-bearing areas. Uranium has also been located by this method.

Jan 1, 1989

By T. Guerin

More than 370 million litres of oil leak from hydraulic equipment every year, excluding all other sources of plant fluid losses. This item analyses the causes of fluid spills from plants and equipment on resource construction sites, and offers some possible solutions.

Apr 1, 2015

By D. D. Lauriski

The Mining Division of Utah Power and Light Company is located in the coal fields of southeastern Utah -main office in Huntington, Utah. The Division will produce 6.5 million tons of low sulfur steam coal in 1988, making UP&L the largest underground mining operation west of the Mississippi. Coal is mined from three underground mines utilizing continuous miner and longwall mining methods. All coal produced by the Mining Division is utilized at UP&L&apos;s two largest steam-electric power plants, the Hunter and Huntington plants with a combined capability of 1,995,000 Kw. At UP&L we believe that to achieve success a company must have clearly defined goals which are understood, communicated and shared at each level of operation. We have also found from experience that a safe operation is generally an efficient and productive operation. As a Division, we have established a goal to achieve the safest, most efficient operation in the country. This is an ambitious goal. To achieve such a goal requires real commitment and a safety/training program capable of achieving needed results. The following is an overview of the program we have established at UP&L which has enabled us to reduce our accident frequency rate from over 40 in 1980 to 8.00 at present, as illustrated in Figure 1.

Jan 1, 1989

"Outotec’s TankCell® e500 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland. The TankCell® e500 is the first cell in this size class (500m3) to be run in an operational duty and it has been working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50. In addition the cell has proved to be very energy efficient, operating with a specific energy of around 0.4kW/m3 under production conditions. This presentation will provide a review of the installation and operation of the TankCell® e500 at Kevitsa and will summarize the results found in the published literature from the various testing campaigns conducted around the cell. INTRODUCTION The TankCell e500 was installed and commissioned at the Kevitsa mine in northern Finland in 2014. Post startup the cell was initially run for testing and optimization with various test campaigns undertaken. but was subsequently taken into a production duty (Mattson et al., 2015a). At Kevitsa the cell is run as the first copper rougher replacing the previous two copper roughers (both 160m3) in this duty. The unit is running at between 38-40% solids at a feed rate of approximately 850tph. Since operational the average copper recovery from this single cell has been around 71% copper. This is typically with an enrichment ratio of around 50 being fed with an average head grade of 0.3% copper. More details on the circuit configuration and production performance of the e500 at Kevitsa can be found in Mattson et al., (2015a) and Murphy et al., (2016). In addition through the optimization program with the use of a variable speed drive controlling rotor speed it was found the the e500 was very energy efficient under production conditions. During this work the cell was found to run at a specific energy of around 0.4kW/m3 which exceeded design expectations (Xia et al., 2015)."

Jan 1, 2016

By Nav Dhadli

Tailings from Oil Sands MiningWhat are they? Challenges Solutions Regulatory Environment Definition of the AFD Tailings Treatment Process 2010 AFD Pilot/Demonstration ProgramTechnical challenges Performance and Results Next steps Oil Sands Industry Collaboration on Tailings Technology TAILINGS ?WHAT ARE THEY? Mixture of remaining water and solids following bitumen extraction process Composed of water, sand, silt, clay, small amounts of hydrocarbon (bitumen, solvent, and asphaltenes) A necessary part of production in excavation of oil sands and removal of bitumen

May 1, 2011

By George C. Riley

While the general public has little knowledge or appreciation of either the mining or explosives industries, modern civilization could not exist without them. They are to-day the key industries of the world. In common with many other industries the demands of the war greatly stimulated the production of explosives and the research necessary for such increased production. Production, supplies of all kinds, munitions of all sorts and then again production, practically regardless of cost, were the first reactions to the imperative war demands of the governments of the world. Following the war there was a momentary lull, then first gradually but with quickening acceleration, particularly in a recent slump, the situation was reversed - cost and not production was the dominant factor. Some industries readjusted themselves very rapidly and completely. Others were but partially re-adjusted and others again only carried out the process of deflation in certain departments. The explosives industry in Canada has not only thoroughly deflated itself, but has learned to apply to commercial disruptive explosives, the best, most efficient and most economical methods of manufacturing developed during the war. As a consequence, miners have at their disposal to-day better and more different kinds of compressed energy than ever before in all the long history of mining.

Jan 1, 1925

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009

By Yuuki Hagio, Hiroyuki Tobo, Michihiro Kuwayama, Yasutaka Ta

"Reduction of CO2 emission is necessary to remedy global warming, however, promising approaches of CO2 separation require a large amount of energy. Molten slag, which is generated as by-product of steel production, has high temperature, but its energy has not been harnessed. To recover the thermal energy from the slag and to apply to separation of CO2 are economical and environmental conscious ways. We propose a new heat recovery system, in which, molten slag is solidified continuously on water-cooled roll and the solidified slag plates are charged into counter-current heat recovery equipment. In laboratory scale experiments, heat recovery ratio of more than 30% was acchived by controlling the thickness of slag.IntroductionThe steel industry in Japan has been working on the projects of ""Environmentally Harmonized Steelmaking Process Technology Development (COURSE50)"". COURSE50 aims at developing technologies to reduce CO2 emissions by approximately 30%. One of the main technologies is to capture and recover CO2 from blast furnace gas using chemical absorbents to regenerate CO2-laden chemical absorbents by separating CO2 from the absorbents. As one of the solutions, JFE Steel Corporation has been developing sensible heat recovery process from steelmaking slag. It is effective to recover and use unutilized high temperature waste heat within a steel plant as the thermal energy required."

Jan 1, 2012

By P. F. Hara, O&apos

Stratabound Proterozoic precious metal mineralization in central Arizona is associated with felsic and adnesitic to mafic volcanic rocks and sediments derived from these rocks. Hydrothermal fluids associated with felsic volcanism form gold mineralization within hotspring vent complexes or within asymetric basins, which flank the vent complexes and are filled with tuffaceous sediments. Massive to semi-massive sulfide copper-zinc systems associated with felsic volcanism may locally contain small gold occurances either laterally or vertically zoned from the ore. In andesitio to mafic rocks, zinc-lead-gold-silver-copper bearing mineralization and gold mineralization are both associated with feruginous sulfide bearing cherts. The partitioning of gold into these specific geologic environments may be related to variations in temperature and composition of the hydrothermal fluid and the depth of the seawater-sediment interface below sea level during the mineralization event.

Jan 1, 1988

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbon-ate gangue from sedimentary apatites "francolite" in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high Mgo siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate, from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the Mgo was rejected in the froth and the phosphate flotation stage produced concentrates analyzing about 31% P2O5,0.7% HgO and 4% insol. The overall P2O5 recovery in the two stages is about 85%.

Jan 1, 1989

By Brooke Clements

The Buffalo Head Hills region is located approximately 350 kilometres northwest of the city of Edmonton in northcentral Alberta (Figure 1). The Alberta diamond joint venture consisting of Ashton Mining of Canada Inc., Alberta Energy Company Ltd and Pure Gold Minerals Inc. began exploring for kimberlites in the Buffalo Head Hills region in late 1996. At the time, the Mountain Lake diatreme, located 200 kilometres to the southwest, was the only reported kimberlitic rock in Alberta (Leckie et al., 1997, Figure 1). Exploration efforts since 1996 have successfully identified a new diamondiferous kimberlite province in Canada.

May 1, 2001

By K. P. Pavlich

Strategic planning, including the process of developing competitive strategy, is an integral part of all organizational management; from one person operations to multi-national Fortune 100 firms. The structure of that process varies from decisions and direction based upon one person&apos;s intuition to the integration of multiple strategic planning groups from each of a firm&apos;s many business units. Everyone has heard interesting strategic planning stories such as the railroad industry&apos;s long term failure to realize that they were in the transportation business and not the railroad business, the decision to "give away the razors and sell them the blades", Caterpillar&apos;s "SOQ NaP" campaign (Sell On Quality, Not On Price), or the tanker industry&apos;s eventual realization that by better managing turn-around the firm could control their largest single cost: depreciation. It is important to remember that very few strategic planning decisions are going to become Harvard Business Review case studies. That fact does not, however, diminish the need for understanding the firm&apos;s business, and actively planning how it is going to remain in business in the future!

Jan 1, 1989

Objective: To improve the effectiveness of dust collector capture on surface mine drills.

Oct 1, 2005