Search Documents

By M. C. Ruiz

This work outlines the results of leaching studies on a copper concentrate containing chalcocite (Cu2S) and digenite (Cu9S5) with an acid saline solution of cupric chloride oxygenated at ambient pressure. The variables studied included the stirring speed, concentration of cupric ions, concentration of HCI, concentration of chloride ions, oxygen flow rate, temperature and time. The leaching system was found to be very effective for the dissolution of the concentrate. Over 95% of the copper was dissolved in 30 minutes with negligible dissolution of iron. The dissolution of copper increased with the stirring speed up to about 400 rpm and depended little on the total chloride concentration. The oxygen flow rate affected the dissolution of copper only below 0.1 1/min. The concentration of HC1 did not influence the dissolution providing its was sufficient to avoid the precipitation of copper oxychloride. The study of the effect of the temperature showed a maximum in copper dissolution around 90 "C

Jan 1, 1997

By E. G. King

Thermodynamic data for the hydrated varieties of alumina are sparse, and those for the common clay minerals are virtually nil. This paper partly fills the vacuum by reporting low-temperature heat-capacity measurements and entropy evaluations of diaspore (A10(OH)) and three clay minerals of the composition A12Si207?2H20 - kaolinite, dickite, and halloysite. The heat-capacity measurements were made in the temperature range 510 to 298.15° K., and the entropies were evaluated at 298.15° K. Diaspore has an unusually low heat capacity and entropy compared with boehmite (another mineral of the same chemical composition). The entropies of the three clay minerals differ too little for entropy to be the important factor relating to differences in the thermal stability of these substances.

Jan 1, 1961

By Ch. Enkhbold

Underground mining of minerals is becoming an increasingly complicated technological and ecological problem. It can be explained both by worsening of geological conditions of mining and by a specific character of mining industry, which, in contrast to processing branches of industry, intrudes into one of principal components of the nature ? the Earth's interior. At a traditional organization of mining industry, the entire volume of the produced rock mass is brought to the Earth's surface, where valuable components are extracted. This entails not only power over expenditure for long-distance transfer (especially in the vertical direction) of the waste rock forming a part of the original mineral, but also the formation of huge volumes of worked-out spaces. The latter leads (nature cannot stand emptiness!) to an irreversible development of geomechanical processes of shifting of overlying rock masses resulting in an irreparable damage of all surface structures located on the territory undermined by deep mining. Owing to their high productivity combined with low power consumption and instrumental compactness, novel bifunctional technological processes of minerals dressing successfully solve the problem of rock mass processing in underground conditions with subsequent operative disposal of final tailings of such underground dressing in the worked-out space. Besides, an integration of two processes into one is achieved, for example, a decrease in the rock mass coarseness with a simultaneous precise separation of valuable and waste components.

Aug 1, 2013

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By Hao Deng, Hongmin Zhu, Jichao Li, Kai Huang

"Silicon and silicon carbide mixing micropowders obtained from the saw cutting industry of polycrystalline silicon ingot is separated by a simple sequential sedimentation. The Zeta potentials of the powders in the aqueous suspension are adjusted by varying the pHs with dilute acid or alkaline reagents. The dispersion and aggregation content of the microparticles is significantly influenced by pHs, and so their settlement velocity in the same hydraulic conditions are quite different, and silicon powders tend to suspend in the upper section of the suspension for its finer size and smaller density under the stronger Zeta potential repulsion force. The original content of the cutting powders with 30%wt silicon are separated into the Si-rich and SiC-rich powder respectively, and 62%wt Si-rich powder can be obtained after 4 times of sedimentation under pH = 8.0, showing the great potential for Si and SiC powder separation and recovery in a cost-effective way.IntroductionWith the fast development of photovoltaic (PV) technology these years, the market demand for the solar-grade high pure silicon material significantly increased, making the silicon recycling and recovery from the wire sawing slurry profitable and attractive[1]. Waste silicon slurry was produced in the multi-wire sawing process of a silicon ingot by using an ethylene glycol-based solution and silicon carbide abrasives as the slicing system. During this slicing process, about 30% of the silicon ingot will become the waste as the fine particles suspended in the slurry, which mainly consists of silicon kerf-loss particles, SiC fragmental particles, tiny iron fragments from the worn sawing wire and ethylene glycol-based solution [2]. The separation of above individual component is usually easy except for Si and SiC fine particles for their quite similar properties. So the biggest challenge for the effective recovery and recycling of silicon particles from the wire sawing slurry actually lies in the mutual separation of silicon and silicon carbide particles."

Jan 1, 2012

By T. -W. Hong, Y. Son, S. -J. Hong, D. Choi

The characteristics of indium-tin-oxide (ITO) nanoparticles recovered from TFT-LCD panel scraps were investigated. The ITO was separated from TFT-LCD panel scraps by dissolving the color filter layer located between the ITO layer and the glass substrate. The solution was filtered to separate the ITO from the color filter component, and the filtered ITO was dissolved in the acid solution. ITO nanoparticles were then precipitated with ammonium hydroxide and organic dispersing agent, followed by heat-treatment at 600 °C. HRTEM, EDX and XRD analyses revealed that the 20 nm sized particle were composed of 90 % In and 10 % Sn, and were well crystallized to in the (222) preferred orientation.

Jan 1, 2014

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

In connection with tin strategic minerals investigations of the Bureau of Mines and the Geological Survey under authority of the Strategic Materials Act (Public 117, 76th Cong., 1st sess.) a study is being made of tin deposits in the United States in an effort to improve the situation with respect to domestic supplies. These studies include sampling and exploration of some of the larger deposits with the objective of establishing emergency reserves, if possible to do so. Two exploration projects have been completed, and the over-all results obtained are set forth in this progress report. RESOURCES Tin was first discovered on this continent in 100 in the Temescal Mountains of what is now southern California. In the ensuing century, occurrences of tin have been reported in no less than 17 States and Alaska. Although most of these are of scientific interest only, tin-bearing veins and placers in California, Alabama, North and South Carolina, Virginia, South Dakota, Wyoming, Texas, New Mexico, and Alaska have been extensively explored, and largo sums of money have been expended in recurring attempts to exploit them.

Jan 1, 1941

By G. L. Alston

Rigid urethane foam can be used effectively for improving mine air conditioning systems by reducing heat and moisture transfer from mine rock to ventilating air and from mine rock to ventilation ducts, for erecting mine ventilation stoppings and overcasts, for sealings around door frames and bulkheads to prevent air leakage, for preventing spalling and sloughing of roof and rib and for erecting fire-resistant powder magazines and transformer or compression stations. Rigid urethane foam is a tough, cellular material, made by nixing diisocyanate and polyether polyol resin in accurate proportions through an applicator system, then the two chemicals react, the mixture expands thirty times its original volume with 85 to 95 percent closed cells. Within seconds, the mixture solidifies and takes a preset which will adhere to overhead or vertical surfaces. It will adhere to brattice cloth, steel, wood, concrete and rock, Excessive wetness will reduce the adherence, but in such cases adherence can be improved by preliminary application of an absorbent dust such as cement.

Jan 1, 1963

By Sven Petersen, Iain J. Stobbs, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONIt is widely thought that seafloor massive sulphide (SMS) deposits, the modern analogue of volcanogenic massive sulphide (VMS) deposits, present a potential global resource for base (Cu, Zn) and precious metals (Au, Ag). In addition, SMS deposits can be enriched in ‘critical metals’ including Se, Te, Tl [1], which are essential for use in the construction of modern and green technologies. Globally over 340 high temperature hydrothermal sites have been identified at a range of ocean spreading centres [2], significant massive sulphide deposit formation has been recorded at 165 of these sites [3].To date only 13 deep sea sulphide deposits have undergone intrusive investigation (drilling or coring) and of these, only 6 sites have published tonnage estimates [2]. Almost all research and drilling of SMS deposits has been focused on active systems, the investigation of the morphology, subsurface structure and mineralogy of hydrothermally extinct seafloor massive sulphide (eSMS) deposits is almost non-existent.As such, little is known about the mechanisms that operate post-SMS formation and which have an impact on the preservation and hence resource value of SMS. Identifying these generic processes and mechanisms, and the extent to which they impact the resource grade, is critical in evaluating the global potential of SMS."

Jan 1, 2017

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By B. A. McKee, T. Adamcewicz

For a capital expenditure of only $46,000, Caland Ore Company has successfully converted its three dry grinding center peripheral discharge rod mills to dry grinding ball mills. The conversion has resulted in a significant capacity increase, operating cost reductions and in-plant environmental improvements. This paper describes why and how• the conversion was made.

Jan 1, 1972

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By J. L. Uhrie

A potentially cost effective technique for the reclamation of heavy metal contaminated soils and sediments involves the technique of froth flotation. Heavy metals sorbed to clays in the soil may be sulfidized by the introduction of sodium sulfide and floated using a dithiophosphate collector. Separations were obtained where up to 78% of all copper ion was removed from the system. Selected samples were floated in a column cell but little advantage was seen.

Jan 1, 1996

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By S. C. Dhara

The recovery of Platinum Group Elements from various industrial scraps and spent materials in the form of high and low grade, such as, impure metals, matte, catalysts and other ceramic substrates, etc., has .been described by using high pressure reaction method. Nickel, Stainless Steel, Titanium and glass lined reaction vessels? are used in the reaction process. Primarily, the method involves either direct leaching of the substrates from the metal value or dissolving the precious metal from the substrate. Both acids and alkalies are used along with other reagents in the reaction process. The temperature and pressure of the leaching process are the main criteria for the reaction kinetics.

Jan 1, 1989

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By Fred D. Wright

A compressor and utility station, which is believed to be one of the largest mobile units of this type ever constructed, was placed in operation at the Bureau of Mines experimental oil-shale mine near Rifle, Colo., during. 1949. This mobile unit mounts two 770-cubic-feet-per-minute air compressors, a 2,500-gallon water tank, and a 200-cubic-foot air receiver. The mobile base of the unit is a 30-ton trailer 30-feet long and 12-feet wide. Prior to the construction of this unit, compressed air was supplied to underground workings through pipe lines connecting with a stationary compressor plant on the surface. The power consumed in supplying compressed air to underground drilling crews was 0.531 kw.-hr. per ton of shale broken. Use of the mobile unit has cut this figure to 0.421 kw.-hr. per ton of shale broken and, more important, has eliminated the cost of installing and maintaining underground air and water lines.

Jan 1, 1950