Search Documents

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

By John Wightman

LOCATION OF PROPERTY THE property of Caribou Gold Mines, Limited, is situated in the north-eastern part of Halifax county, seven miles south of the Canadian National railway line at Upper Musquodoboit. Approach to the village is by a secondary road, improved recently by waste rock from the mine dump. A two-wire telephone line, seven miles long, built and owned by the present operators, provides communication to the nearest telephone exchange, Parker's Corner. HISTORY In 1870, the Caribou area was recognized as a proclaimed gold district. From then on, operations were intermittent, with periods of considerable activity by small companies until there were no fewer than seven mines in a district two miles long by three-quarters of a mile wide. These were the Holman, Truro, Caffrey, MacDonald or Elk, Lake, Dixon, and Hilchey properties, all of which have had separate stamp-mills, and have produced gold for varying periods. Depths of the workings range from 100 feet to 1,000 feet. Power was generated at each property by means of steam boilers. At the present time, the Consolidated Mining and Smelting Company of Canada, Limited, controls all the leased areas, approximately 800 acres, and is operating by means of one central vertical shaft. GEOLOGY The district in and about Caribou Mines has an elevation of approximately five hundred feet above sea level. The area is fairly well wooded, with rock outcrops here and there. These outcrops, along with information from test-pits and shafts, have been the basis for the very excellent geological map of the district prepared by E. R. Faribault some years ago. The rock structure, which is one of the best examples in Nova Scotia of an elliptical dome, has its anticlinal axis in a northeast-southwest direction, and flat plunges in the same directions.

Jan 1, 1938

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996

By I. Farr, M. R. Mock, J. C. Robison

"HPAL and POX autoclave vapor-space gasses are vented through an autoclave PCV (Pressure Control Valve). The downstream steam-born mist of liquid droplets and solid particles travels in excess of 1000 m/s with megawatts of kinetic power at temperatures up to 160 C. The characteristics of downstream states often result in problems with corrosion, erosion, noise and vibration. Comprehension of those and related characteristics aids in improved pressure control, overpressure control and autoclave level control. We introduce compressible multiphase flow concepts and constructs germane to such flow including choked flow, continuous phase change, shock waves and supersonic flow plumes. Flow modeling based on first principles quantitatively predicts such flows providing a tool for component sizing and a method to estimate effects of water injection on flow. Insight deduced from modeling aids in mitigation of afore mentioned problems of which we share some from-site examples.INTRODUCTION First principles related to fluid thermodynamics and compressible flow have been employed akin to their application in the rocket industry. We will present the results of the application of those principles conceptually and authentically without mathematical rigour while using language of the pertinent disciplines. The autoclave (AC) vapor space over the slurry of a POX (Pressure Oxidation) or HPAL (High-Pressure Acid Leach) system (depicted in Figure 1) is vented via a PCV (pressure control valve) followed by certain ducting, and perhaps a nozzle, before exiting at atmospheric (typically) pressure. As indicated by its name the PCV controls the AC pressure as the flow control component of a pressure control loop."

Jan 1, 2017

By C. E. Baltzer, W. H. Harper

"This study has been developed to illustrate the trend and pattern of distribution applying to the quantities and costs of the fossil fuels used, and the related amounts of electricity generated, in the thermal segment of the Canadian electric utility industry.Traditionally, Canada's requirements for electric energy have been preponderantly met by hydraulic power. The need for augmented supplies of thermally generated power has mainly developed since the close of World War Il-in an era that has seen drastic decline in the production of indigenous coal and buoyant expansion in the supply of oil and natural gas. Although coal currently is faced with serious competition from the fluid fuels, the utility industry in particular promises an advancing market for coal, because of its abundant resource, at prices less likely to show sharp increase. For Canada as a whole, this trend has been progressive since 1959, and, unbelievable as it may now seem, the extent of the advance by 1975, particularly in Ontario and the Prairie Provinces, may well be as much, or even more, than the present rate of consumption for all purposes.The text and the tables and charts are arranged to focus attention on: the growth of thermal genera ting capability; the historical trend in consumption of fuel and the related production of electricity; patterns of distribution by types of fuel and thermal capacity; the relationship of steam to other sources of thermal capacity; and the quantities, costs and related percentages of electricity generated by types and kinds of fuel used, both regionally and provincially."

Jan 1, 1966

By D. Mishra

Electric arc furnace dust (EAFD) generated during the recycling of steel- scrap is classified as a hazardous waste for landfilling. This is because it contains leachable heavy metals such as zinc, lead,... Recovery of these metals could result in both resources conservation and resolving waste disposal problems. A study of the thermal reduction of a sample of EAFD was carried out in an inert gas atmosphere using coke as a reducing agent. Preferential volatilization of zinc and lead was achieved during the reduction process at about 800 "C. More than 96 % of both zinc and lead were removed from the dust and were recovered in the condensates. The treatment residue was essentially composed of iron oxides and almost free from heavy metals.

Jan 1, 2002

China has been producing gold for more than 4000 years with gold production increasing substantially since the 1980s, from about 25 tonnes in 1980 to some 160 tonnes in 1998. More than 80 per cent of the gold production is from East China. However, complete information on eastern China gold has been rarely reported internationally. This is a general overview on the tectonics and metallogeny of gold deposits in East China. The geology of these gold deposits is compiled mainly from data and information reported in China, and is also based on the authorÆs work in China from 1974 to 1986 and a recent visit to China.

Jan 1, 1999

By O. A. Velasquez, A. R. Kumar

"Dust generated on underground mechanized coal mining faces is a health and safety hazard. Continuous miners deployed underground usually have an integrated flooded-bed dust scrubber mounted onto the machine that arrests the generated dust from close to the face and cleanses the air around it. However, the impingement screen might get clogged depending on the coal seam being worked. This necessitates the cleaning of the screen which in turn, reduces the overall availability of the scrubber and, hence the continuous miner. A novel non-clogging screen has been developed at the Department of Mining Engineering, University of Kentucky. The proposed impingement screen is built up of three individual aluminum screen units 1.5 mm thick and separated by 3 and 2 mm respectively. The screens have long vertical slits measuring 6 mm. A water spray continuously keeps the screen wet and provides for the filter element to arrest the dust particles. The slits force the dust-laden air to make sharp turns. The dust particles cannot change directions rapidly, impact one of the three screens and are separated out based on their momentum. Preliminary computational fluid dynamics (CFD) models have indicated significant cleaning efficiencies in the respirable range at the expense of much lower pressure drops. Results indicated by CFD models and supported by laboratory experiments have been discussed in this paper.ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research. Dr. Thomas Novak, Professor of Mining Engineering, is also acknowledged for his continued support and encouragement. INTRODUCTION Continuous miners are ubiquitous in coal mining around the world. The miners are operated against bling headings, ensuring adequate flow of air at the face could be difficult. The minimum requirement of ventilation airflow quantities at those coal faces are legislated to dilute dust generated to harmless levels. New dust rules promulgated recently have further called for lower exposure levels of personnel working underground (Courtney) (MSHA, 2014) (NIOSH, 2010). Water sprays are also installed at strategic locations and serve as powerful air-movers. The sprays capture some amount of dust generated while cutting. In addition to this, usually, all continuous miners are equipped with a flooded-bed dust scrubber as shown in Figure 1 to capture the dust from close to the extraction drum (Chao & De-sheng, 2000) (Wala, Vytla, Huang, & Taylor, 2008) (Organiscak & Beck, 2010)."

Jan 1, 2018

By G. Archer

ASARCO, a large and diverse producer of nonferrous metals, is involved primarily in the smelting and refining of lead and copper. Lead-antimony alloys, antimony trioxide, bismuth, cadmium oxide, selenium, tellurium, silver and gold are among products which result from processing by-products of smelting and refining. The complex mixture of concentrates at some smelters and the high impurity loads at some refineries result in various drosses, sludges, dusts and slags. In this paper, the complex interplant and intraplant transfer of by-products is addressed. These by-products result in an exchange of metals between the lead circuit and the copper circuit. Examples of the transfer of by-products and the prospects for the recycle of valuable products from wastes generated by customers and unrelated processors are also discussed.

Jan 1, 1992

By Paul Girard

"The copper property of Madeleine Mines Ltd. is in Lapotardiere and Boisbuisson townships, Gaspe North. The initial find was made in 1964, and subsequently a copper deposit of 5.3 million tons of ore was outlined. The property lies in Ordovician sedimentary and volcanic rocks near the major granite intrusive of the McGerrigle Range. The host-rock is a 300-foot-thick metamorphosed silty shale unit, close to the contact of the intrusive. The structure itself coµsists of a southerly-dipping monocline or the south limb of an anticline, on which a large dragfold has been imposed.Chalcopyrite, bornite and chalcocite are the principal sulphides present in the ore. Of particular interest is the zoning arrangement of these sulphides. The orebody is chimney-like in shape and appears to be a fracture-filling deposit that is genetically related to the granite intrusive and is confined within a highly fractured zone of very brittle rock. The deposit presents features uncommon to any of the other known copper deposits in the Gaspe Peninsula."

Jan 1, 1969

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By William D. Riley

The U. S. Bureau of Mines has developed technology to recover by-product materials from aluminum scrap using engineered scavenger compounds (ESC). ESCs are structural oxides with a channel or tunnel structure that allows them to hold ions of a specitksizes and charges. The scavenging reaction is easily reversible allowing the ESC to be recharged for continued use and the ion is recovered as an electro deposit. Key features of this novel technology are; a) ESC ,systems are designed to have a high degree of selectivity for a desired ionic species. b) The recovered mater.ial requires little or no additional reprocessing prior to reuse. Two current uses for the ESC technology that are described in this paper are the removal and recycle oflithium (Li) from lithium aluminum (Li-AL) alloys; and, using ESCs as a replacement for the conventional demaging (magnesium removal) technology used by the secondary casting industry. Research indicates that the ESC technology proposed for both these applications has either 'distinct economic and/or environmental advantages over previously employed methods of recovering. metal values from aluminum scrap.

Jan 1, 1995

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973

By Rahul Bhaduri

Mercury levels in Twin Creeks Vista pit ore (previously Chimney Creek, North pit ore) increased substantially since plant start-up in November 1987. Consequently, modifications were necessary to minimize industrial hygiene hazards and potential operational problems. The original plant design included mercury control measures. With progressive increases in mercury levels, the issue had to be re-addressed. Modifications to operational practice, industrial hygiene and management philosophy will be discussed. Additionally, a detailed examination of the mercury vapor suppression system currently employed at Twin Creeks will be presented.

Jan 1, 1994

By R Bertuzzi

Permanent rock bolts in civil engineering are taken as having to serve their design purpose for at least 50 years. In many projects the design life is specified as greater than 100 years. A review of recent Australian tunnelling projects shows that substantial differences exist in the level of corrosion protection provided for permanent steel shafted rock bolts. This paper reviews the current state of practice and sets out what the authors consider to be appropriate requirements for corrosion protection.

Jan 1, 1999

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983