Search Documents

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills AQ or BQ holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

The main purpose of mine ventilation design is to provide sufficient quantity and quality of air to the workers and to dilute methane and other contaminants. It is generally perceived that the additional air along the longwall face will improve methane dilution on the face and in the tailgate. However, computational fluid dynamics (CFD) modeling efforts at the Colorado School of Mines (CSM) under a National Institute for Occupational Safety and Health (NIOSH) funded research project have found that higher flow velocities along the longwall face are shown to increase the pressure differential between the gob and longwall face allowing more methane to be entrained in the active face and tailgate (TG) area, thereby negating the dilution effect. The increased face ventilation causes an increase in pressure along the headgate side which allows more oxygen to ingress into the gob area, thereby increasing the amount of oxygen available to form explosive methane air mixtures in the gob and to support spontaneous combustion of the coal. Two things are happening at two different locations along the longwall face, increase in pressure as the flow enters the active area cause an increase in pressure which forces more oxygen into the gob, but as the flow is developed along the longwall face, the higher velocities causes greater pressure drop allowing methane to enter the active face further downstream from the headgate (HG) towards the tailgate side. In this paper, a parametric study will be presented to discuss the effect that varying the face air quantity has on methane concentrations in the tailgate and formation of explosive gas zones (EGZs) in the gob. Counter to conventional wisdom, it appears that increased longwall face air quantities may increase the explosion hazard as they result in increased EGZ volumes in the gob, along with increased methane quantities in the tailgate return.

Jan 1, 2015

By Rolf Andreas Lauten, Yanhong Wang, Yongjun Peng

"In mineral flotation, bentonite as a kind of clay mineral imposes deleterious effects on the flotation of valuable minerals, possibly through its ability to increase the pulp viscosity. A higher viscosity lowers the amount of froth and affects the bubble-particle collision frequency. A previous study found that adding gypsum to a bentonite-ore mixture lowered the viscosity, possibly by inhibiting the formation of interconnected network structures. In this study, sulfate as an anion with different types of cations, Na+, K+, Mg2+ and Ca2+ were used to reduce bentonite viscosity and to improve flotation performance. It was found that at the same concentration, MgSO4 was the most effective salt in reducing bentonite suspension viscosity, while CaSO4 was not as effective likely due to the lower solubility of CaSO4. Na2SO4 and K2SO4 reduced bentonite suspension viscosity at high concentration. Flotation kinetics of ore blended with bentonite was increased with increasing the electrolytes concentration, which generally correlated with the reduction of bentonite viscosity. Meanwhile, significant discrepancies were found between flotation results and rheological measurements in the presence of monovalent ions. It is indicated that the morphology of bentonite aggregates in electrolytes solution is likely to influence the hydrodynamics in the froth zone.INTRODUCTIONClay is present in many ore bodies as a gangue mineral. Presence of clay presents several challenges in the processing of valuable minerals. They are soft compared to valuable minerals, which means that during grinding of the ore, clay particles are likely to obtain a smaller particle size than the valuable mineral. Often clay particles may be within the colloidal size domain (<20 µm). The smaller size increases the probability of entrainment in the concentrate. Another challenge is their anisotropic charge distribution, where depending upon the pH, edges (E) and faces (F) carry charges of opposite sign. This facilitates formation of aggregation structures that may impede percolation of bubbles through a froth, but also increase the viscosity more than expected from the mere change in volume fraction. In addition to lowering the froth mobility, a high slurry viscosity will have implications for the gas dispersion in the flotation column as it affects the dispersion of the suspended particles, and it modifies the bubble-particle collision rate and attachment efficiency (Bakker, Meyer, & Deglon, 2009; Shabalala, Harris, Leal Filho, & Deglon, 2011). A pragmatic approach to this problem is to blend high clay ore with ore of lower clay content, reducing the overall clay concentration. Alternatively, one may lower the solids content of the flotation slurry to counteract the viscosity-building properties of clay. While feasible, this approach has the disadvantage of increasing required flotation volume, and it also affects the properties of the froth. Thus, there are currently limited options in lowering the impact of clays and their tendencies to increase viscosity in flotation slurries."

Jan 1, 2016

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a&apos;=0.407 nm for two axes and c&apos;=0.390 nm for the third axis. The a&apos;axis is shorter by 4% than the c&apos;axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000

By M J. Nugus, F Clark, E J. Hill, J T. Carswell, J S. Cleverley, N H. S Oliver

High-nugget gold orebodies are difficult to model in 3D because samples from diamond drill core are generally too small to provide reliable estimates of the gold content of the larger body of rock, and therefore interpolation of gold assay values between drill holes is also unreliable. As a result, gold resources are generally underestimated in areas of high nugget. In practice, proxies for gold mineralisation, such as presence of alteration, specific structures or high vein density, have been used by geologists to predict rocks which are favourable for mineralisation. However, there has been no automated method for combining the predictive capabilities of several proxies, except by human judgement.We have been developing a method to combine several different types of geological features or geochemical analyses into a single measure using conditional probability. Conditional probability provides a meaningful numerical measure for the favourability of rocks for containing high-grade gold mineralisation. This measure can be interpolated in the exploration space, providing a sound basis for a 3D model of the orebody. We have developed this technique using data from the Sunrise Dam Gold Mine, which is a high-nugget orebody hosted in a structurally complex Archaean greenstone belt and which has historically proved to be a very challenging orebody to model.CITATION:Hill, E J, Nugus, M J, Clark, F, Oliver, N H S, Cleverley, J S and Carswell, J T, 2013. Predictive three-dimensional modelling of nuggety gold orebodies, Sunrise Dam, Western Australia, in Proceedings World Gold 2013 , pp 463-468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Vicken Aprahamian

"The Royal Canadian Mint (RCM) operates a gold and silver refining toll operation in Ottawa, Ontario, Canada. The silver refining line is a recent addition and was commissioned in 2005. One source of silver in the refinery is from gold doré which undergoes Miller chlorination before electrorefining to 99.99% cathode gold. Treatment of the Miller salt or silver-copper chloride produced consisted of a 2-stage high temperature reduction process step using soda ash prior to 2005. Copper-rich silver bars were produced and shipped offsite for further refining.The copper-rich bars could not be blended into sufficient high grade silver doré to dilute the copper and allow electrorefining in a silver nitrate medium. A new wet process was developed and commissioned to replace the high temperature reduction and allow removal of bulk copper. Thus upgraded impure silver produced was cast into anode for electrorefining to 99.9% purity silver flake. The 2005 RCM Hydromet Slag process is presented as well as its more current version. In addition, mention is made of a novel processing scenario for the introduction of Miller chlorination silver into the electrorefining circuit."

Jan 1, 2015

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By D. L. Shenck

The Navajo Mine is exclusively a multiple seam surface coal mine located in the northwest corner of New Mexico, and entirely on the Navajo Indian Reservation (Figure 1). It is owned and operated by the Broken Hill Propriety Co., Ltd. of Melbourne, Australia. The mine began production in January 1963 with a long term fuel supply agreement with the Four Corners Power Plant. The 2175 MW nominal generating capacity of the Four Corners Power Plant consumes 8-8.5 mm tons of coal annually. With estimated reserves totaling 1.1 billion tons of strippable coal, only one third is presently committed to the generating station. As development has continued over the years, mining operations have advanced into more complex geologic areas to satisfy the utilities demand for coal.

Jan 1, 1990

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because &apos;of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By Y Li, S Ramazan, E Topal

A mine waste dump progression plan can provide a clear outlook of the mining operation. To produce such an output requires detailed placement schedule of the mined material, including the volume (or tonnage) and the allocated dumping location. However, current practise mainly focuses on the ore production, over-simplifying the waste material scheduling. As a result, a rock dump is often treated as a single point in long-term planning, making it difficult to predict the waste dump progression pattern over the life-of-mine. Without such a guidance, it is almost impossible to carry out progressive rehabilitation on the waste rock dumps. The lack of dumping schedule could cause delay in development construction, ie tailing storage facility and run-of-mine pad. Other downstream effect due to the over-simplification is inaccurate estimation of required truck hours, which could have huge financial impact on the operation.In this paper, mixed integer programming (MIP) models of different objective functions, ie maximise truck productivity by minimising the overall haulage distance, minimise required truck deviation between adjacent years, and a hybrid between the two objectives, are utilised to generate the long-term optimum rock placement schedules under the criteria of satisfying site specific conditions. All three MIP models are implemented in a large scale open pit mine. The numerical solutions from the models forms three different rock placement schedules, based on which, the yearly truck requirements are easily calculated and compared. The graphical results show the three corresponding waste dump progression patterns over the life-of-mine, providing the optimised long-term forecast of the operation.CITATION:Li, Y, Topal, E and Ramazan, S, 2014. Optimising the long-term mine waste dump progression and truck hour schedule in a large-scale open pit mine using mixed integer programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By L. K. Daneshmend

Key issues in managing information systems in the minerals industry will likely continue to be those relating to the integration and interoperability of disparate systems. This paper argues that, in order to harness the promised benefits of information technologies, the mining industry should adopt a set of open systems standards to define data formats and protocols for seamless data exchange. This is in direct contrast to the present situation where mining equipment, software and instrument suppliers rigidly adhere to proprietary standards for fear of losing competitive advantage. Benefits to the mining sector resulting from the adoption of such standards would be: the provision of near-time data for executive decision support, and the freedom to choose best technologies. The principal benefits to the leading mining software suppliers will be increased market share as a result of “captive sites” converting to open systems standards. Examples are given of open systems standards developed for related industries such as the Petroleum Open Systems Corporation (POSC) and the Machinery Information Management Open Systems Alliance (MIMOSA).

Jan 1, 2000

By John Bailey

Stressmap is a program whereby the earth&apos;s stress field is charted in detail and utilized for design of mines and mine exploitation. This program is implemented by mapping the attitude (location, direction, dip, and extent) of induced rock ruptures during the process of hydrafracturing drill holes contiguous to mine interest. The program includes utilization of ancillary naturally occurring stress relief signals, They are precipitated because the earth is indeed dynamic and the strata of the crust are continually adjusting to load and/or strain differentials resulting in rock deformation and fracturing. These fracturing adjustments occur as small to tiny earthquakes comparable to Richter magnitudes of one, zero, minus one, and smaller events termed microearthquakes. Obviously, the earth&apos;s stress field changes due to continued differential loading and crustal movements; therefore it becomes conspicuously evident that resolving today&apos;s stress field as opposed to paleostresses is most important for efficient, economical, and safe mining operations.

Jan 1, 1974

By C. I. Basilio

Pearson&apos;s hard and soft acid and base (HSAB) principle may be applied to flotation systems. The HSAB principle states that hard acids prefer to bond with hard bases and soft acids prefer to bond with soft bases. By determining the Drago E and C parameters for the different components of a flotation system, the HSAB principle could be used to explain the selectivity of some collectors such as thionocarbamates against some minerals. Determination of these parameters is done by utilizing Drago&apos;s theory and flow micro-calorimetry.

Jan 1, 1991

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

Bendigo Mining operates a 600 000 t/a comminution, gravity, flotation and leaching processing plant for the recovery of gold from their Kangaroo Flat Operation, in the Bendigo goldfields. The free gold and gold bearing sulfi des present are typically coarse grained and hence are highly amenable to gravity recovery. Plant operating data is consistently showing that over 78 per cent of the feed gold is recovered in a circuit, consisting of inline pressure jigs, inline spinners followed by free gold tabling and intensive leaching of tabling tails. The circuit receives coarse crushed product from high pressure grinding rolls and the grinding mill discharge, which allows material to be re-circulated through the gravity process until the particles are small enough to enter the flotation circuit. A plant audit was completed on 26 November 2009 designed to give an indication of the overall operational characteristics of the gravity circuit including single pass efficiencies of associated equipment. The techniques, results and challenges of such a survey are discussed.

Aug 1, 2010

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014